Features
■ High speed
–t
= 5.5 ns (typ.) at VCC = 5 V
PD
■ Low power dissipation
–I
= 2 μA (max.) at TA = 25 °C
CC
■ Typical hysteresis: V
■ Power-down protection on inputs
= 1 V at VCC = 4.5 V
h
– Symmetrical output impedance
|I
| = IOL = 8 mA (min.)
OH
■ Balanced propagation delay
–t
■ Operating voltage range
–V
■ Pin and function compatible with 74 series 14
■ Improved latch-up immunity
■ Low noise
–V
≅ t
PLH
CC
OLP
PHL
(opr) = 2 V to 5.5 V
= 0.8 V (max.)
Applications
■ Automotive
■ Industrial
■ Computer
■ Consumer
74VHC14
Hex Schmitt inverter
Datasheet − production data
SO-14TSSOP14
Description
The 74VHC14 is an advanced high-speed CMOS
hex Schmitt inverter manufactured with submicron silicon gate and double-layer metal wiring
2
C
MOS technology.
The internal circuit is composed of 3 stages
including a buffer output, which provides high
noise immunity and stable output.
Power-down protection is provided on all inputs
and 0 to 7 V can be accepted on inputs
regardless of the supply voltage. This device can
be used to interface 5 V to 3 V.
Pin configuration and function are the same as
those of the 74VHC04 but the 74VHC14 has
hysteresis.
This along with its Schmitt trigger function allows
the device to be used on line receivers with slow
rise/fall input signals.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2 kV ESD immunity and transient excess
voltage.
Table 1. Device summary
Part number Temperature range Package Packaging
74VHC14TTR -55/+125 °C TSSOP14 Tape and reel
74VHC14YTTR
74VHC14MTR -55/+125 °C SO-14 Tape and reel
1. Qualification and characterization (according to AEC Q100 and Q003 or equivalent) and advanced screening (according to
AEC Q001 and Q002 or equivalent) are ongoing.
June 2012 Doc ID 5741 Rev 8 1/16
This is information on a product in full production.
(1)
-40/+125 °C TSSOP14 (automotive grade) Tape and reel
www.st.com
16
Contents 74VHC14
Contents
1 Logic symbols and I/O equivalent circuit . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2/16 Doc ID 5741 Rev 8
74VHC14 Logic symbols and I/O equivalent circuit
1 Logic symbols and I/O equivalent circuit
Figure 1. IEC logic symbols
Figure 2. Input and output equivalent circuit
Doc ID 5741 Rev 8 3/16
Pin settings 74VHC14
2 Pin settings
2.1 Pin connections
Figure 3. Pin connections (top through view)
2.2 Pin description
Table 2. Pin description
Pin number Symbol Name and function
1, 3, 5, 9, 11, 13 1A to 6A Data inputs
2, 4, 6, 8, 10, 12 1Y to 6Y Data outputs
7 GND Ground (0 V)
14 V
2.3 Truth table
Table 3. Truth table
Input Output
CC
AY
LH
HL
Positive supply voltage
4/16 Doc ID 5741 Rev 8
74VHC14 Maximum ratings
3 Maximum ratings
Stressing the device above the rating listed in the “absolute maximum ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Table 4. Absolute maximum ratings
Symbol Parameter Value Unit
V
I
I
I
GND
T
Supply voltage -0.5 to +7.0 V
CC
DC input voltage -0.5 to +7.0 V
V
I
V
DC output voltage -0.5 to VCC + 0.5 V
O
DC input diode current - 20 mA
I
IK
DC output diode current ± 20 mA
OK
DC output current ± 25 mA
I
O
DC supply current per supply pin ± 50 mA
CC
DC ground current per supply pin ± 50 mA
Storage temperature -65 to +150 °C
stg
Lead temperature (10 sec) 300 °C
T
L
3.1 Recommended operating conditions
Table 5. Recommended operating conditions
Symbol Parameter Value Unit
V
V
V
T
Supply voltage 2 to 5.5 V
CC
Input voltage 0 to 5.5 V
I
Output voltage 0 to V
O
TSSOP14, SO-14 -55 to +125 °C
Operating temperature
op
TSSOP14 (automotive grade) -40 to +125 °C
CC
V
Doc ID 5741 Rev 8 5/16
Electrical characteristics 74VHC14
4 Electrical characteristics
Table 6. DC specifications
Test condition Value
Symbol Parameter
High level
V
t+
threshold voltage
Low level
V
t-
threshold voltage
V
Hysteresis voltage
h
V
V
High level output
OH
voltage
Low level output
OL
voltage
Input leakage
I
I
current
= 25°C -40 to 85 °C -55 to 125 °C
T
V
(V)
CC
A
Min. Typ. Max. Min. Max. Min. Max.
3.0 2.2 2.2 2.2
5.5 3.85 3.85 3.85
3.0 0.9 0.9 0.9
5.5 1.65 1.65 1.65
3.0 0.3 1.2 0.3 1.2 0.3 1.2
5.5 0.5 1.6 0.5 1.6 0.5 1.6
2.0 I
3.0 I
4.5 I
3.0 I
4.5 I
2.0 I
3.0 I
4.5 I
3.0 I
4.5 I
0 to
5.5
= -50 μA 1.9 2.0 1.9 1.9
O
= -50 μA 2.9 3.0 2.9 2.9
O
= -50 μA 4.4 4.5 4.4 4.4
O
= -4 mA 2.58 2.48 2.4
O
= -8 mA 3.94 3.8 3.7
O
= 50 μA 0.0 0.1 0.1 0.1
O
= 50 μA 0.0 0.1 0.1 0.1
O
= 50 μA 0.0 0.1 0.1 0.1
O
= 4 mA 0.36 0.44 0.55
O
= 8 mA 0.36 0.44 0.55
O
V
= 5.5 V or GND ± 0.1 ± 1 ± 1 μA
I
Unit
V4.5 3.15 3.15 3.15
V4.5 1.35 1.35 1.35
V4.5 0.4 1.4 0.4 1.4 0.4 1.4
V
V
Quiescent supply
I
CC
current
5.5 V
= VCC or GND 2 20 20 μA
I
6/16 Doc ID 5741 Rev 8
74VHC14 Electrical characteristics
Table 7. AC electrical characteristics (input t
Test condition Value
= tf = 3 ns)
r
Symbol Parameter
t
Propagation delay
PLH
t
1. Voltage range is 3.3 V ± 0.3 V
2. Voltage range is 5.0 V ± 0.5 V
PHL
time
V
3.3
3.3
5.0
5.0
C
CC
(V)
L
(pF)
(1)
15 8.3 12.8 1.0 15.0 1.0 15.0
(1)
50 10.8 16.3 1.0 18.5 1.0 18.5
(2)
15 5.5 8.6 1.0 10.0 1.0 10.0
(2)
50 7.0 10.6 1.0 12.0 1.0 12.0
= 25 °C -40 to 85 °C -55 to 125 °C
T
A
Min. Typ. Max. Min. Max. Min. Max.
Table 8. Capacitive characteristics
Test condition Value
Symbol Parameter
Min. Typ. Max. Min. Max. Min. Max.
C
C
1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current
consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation.
ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate)
Input capacitance 6 10 10 10 pF
IN
Power dissipation
PD
capacitance
(1)
14 pF
Unit
ns
UnitTA = 25 °C -40 to 85 °C -55 to 125°C
Table 9. Dynamic switching characteristics
Test condition Value
Symbol Parameter
V
CC
(V)
V
V
V
V
1. Worst case package.
2. Max number of outputs defined as (n). Data inputs are driven 0 V to 5.0 V, (n-1) outputs switching and one output at GND.
3. Max number of data inputs (n) switching. (n-1) switching 0 V to 5.0 V. Inputs under test switching: 5.0 V to threshold (V
0 V to threshold (V
OLP
OLV
IHD
ILD
Dynamic low
voltage quiet
(1) (2)
output
Dynamic high
voltage input
Dynamic low
voltage input
), f = 1 MHz.
IHD
(1) (3)
(1) (3)
5.0
C
= 50 pF
5.0 3.5 V
L
5.0 1.5 V
Doc ID 5741 Rev 8 7/16
T
= 25 °C -40 to 85 °C -55 to 125 °C
A
Min. Typ. Max. Min. Max. Min. Max.
0.3 0.8
-0.8 -0.3
Unit
ILD
V
),
Test circuit 74VHC14
5 Test circuit
Figure 4. Test circuit
= 15/50 pF or equivalent (includes jig and probe capacitance)
C
L
R
= Z
T
of pulse generator (typically 50 Ω)
OUT
8/16 Doc ID 5741 Rev 8
74VHC14 Waveforms
6 Waveforms
Figure 5. Waveform - propagation delay (f = 1MHz; 50% duty cycle)
Doc ID 5741 Rev 8 9/16
Package mechanical data 74VHC14
7 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK®
®
is an ST trademark.
10/16 Doc ID 5741 Rev 8
74VHC14 Package mechanical data
SO-14 MECHANICAL DATA
DIM.
A 1 .35 1.75 0.053 0.069
A1 0.1 0.25 0.004 0.010
A2 1.10 1.65 0.043 0.065
B 0 .33 0.51 0.013 0.020
C 0.19 0.25 0.007 0.010
D 8.55 8.75 0.337 0.344
E 3.8 4.0 0.150 0.157
e 1.27 0.050
H 5.8 6.2 0. 228 0.244
h 0.25 0.50 0.010 0.020
L 0.4 1.27 0.016 0.050
k0° 8°0° 8°
ddd 0.100 0.004
MIN. TYP MAX. MIN. TYP. MAX.
mm. inch
0016019D
Doc ID 5741 Rev 8 11/16
Package mechanical data 74VHC14
TSSOP14 MECHANICAL DATA
DIM.
MIN. TYP MAX. MIN. TYP. MAX.
A 1.2 0.047
A1 0.05 0.15 0.002 0.004 0.006
A2 0.8 1 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.012
c 0.09 0.20 0.004 0.0089
D 4.9 5 5.1 0.193 0.197 0.201
E 6.2 6.4 6.6 0.244 0.252 0.260
E1 4.3 4.4 4.48 0.169 0.173 0.176
e 0.65 BSC 0.0256 BSC
K0˚ 8˚0˚ 8˚
L 0.45 0.60 0.75 0.018 0.024 0.030
mm. inch
A2
A
PIN 1 IDENTIFICATION
A1
b
e
c
K
L
E
D
E1
1
0080337D
12/16 Doc ID 5741 Rev 8
74VHC14 Package mechanical data
Tape & Reel SO-14 MECHANICAL DATA
DIM.
MIN. TYP MAX. MIN. TYP. MAX.
A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362
T 22.4 0.882
Ao 6.4 6.6 0.252 0.260
Bo 9 9.2 0.354 0.362
Ko 2.1 2.3 0.082 0.090
Po 3.9 4.1 0.153 0.161
P 7.9 8.1 0.311 0.319
mm. inch
Doc ID 5741 Rev 8 13/16
Package mechanical data 74VHC14
Tape & Reel TSSOP14 MECHANICAL DATA
DIM.
MIN. TYP MAX. MIN. TYP. MAX.
A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362
T 22.4 0.882
Ao 6.7 6.9 0.264 0.272
Bo 5.3 5.5 0.209 0.217
Ko 1.6 1.8 0.063 0.071
Po 3.9 4.1 0.153 0.161
P 7.9 8.1 0.311 0.319
mm. inch
14/16 Doc ID 5741 Rev 8
74VHC14 Revision history
8 Revision history
Table 10. Revision history
Date Revision Changes
12-Nov-2004 6 Ordering codes revision - pag. 1
02-May-2007 7 Document reformatted, updated Table 6 on page 6
Added Applications on page 1
Updated Table 1: Device summary on page 1
15-Jun-2012 8
Updated T
in Table 5: Recommended operating conditions
op
Updated ECOPACK
Minor textual updates
®
text in Section 7: Package mechanical data
Doc ID 5741 Rev 8 15/16
74VHC14
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16 Doc ID 5741 Rev 8
Loading...