SSV Works MRB3 User Manual

RADIO FUNCTIONS

Selecting FM/AM Band: Press MODE until the FM or AM band shows on the display.

Automatic Station Search: Press or to start automatic station search. The search

stops when a station is found.

Manual Station Search: Press and hold or until M - SEEK. Press the or

briey to change the frequency until the desired frequency is set. Change to Automatic

search (A - SEEK) mode after a station is found.

BLUETOOTH AUDIO STREAMING

1. Open the Bluetooth setup program on the mobile device and activate the Bluetooth feature

User Guide

2. The device will show up as “SSV”. Select this device and enter passkey: OOOO

3. After successfully pairing, a Bluetooth logo will appear on the phone menu screen and
show “CONNECT” “BT MUSIC” on the device LCD display.

Stop Playback: Press

Skip Track: Press or to play previous/next song.

briey to pause music. Press button again to continue playback.

CONNECTING AN EXTERNAL AUDIO DEVICE (OPTIONAL)

- Press MODE until AUX shows on the display.

Line in

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All
SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for
replacement of defective components is not covered. All SSV Works Speakers are covered by a limited 1 year warranty
against defects in material or workmanship. Contact SSV Works for further warranty information.

Corporate: SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
Web: www.SSVworks.com | Phone: [phone] | Fax: [phone]

The Bluetooth
marks by SSV Works is under license. © 2016 SSV Works, Oxnard, CA 93030 MRB3 Rev. B 3-22-16

®

word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such

Add 3.5mm AUX-in
and USB Charging with
SSV Works 3PUSB35A
(sold separately)

MRB3

MRB3

Bluetooth® Media Controller

SAFETY INFORMATION

Do not attempt to disassemble or repair the MRB3 yourself. Please call SSV Works for

technical assistance or repair information. Changes or modications to the MRB3 not

authorized by SSV Works will void the warranty.

SSV Works recommends disconnecting the negative battery terminal before

!

beginning any installation.

AMPLIFIER WIRING DIAGRAM

12v+ Yellow

USB 1A charge input

does not read

USB data

Signal ground
(Black)

AMP turn on
(Blue)

BUTTON LOCATIONS AND FUNCTIONS

5

1. Play/Pause
Power On/Off

MRB3

Mute

2. Volume Up/Down

3. Mode

4. Track Forward/Back
Station Forward/Back
Menu Settings Up/Down

5. LCD Display

2

1

3

4

GENERAL OPERATIONS

Power On/Off: Press to power on. Press and hold to power off.

Volume: Press the VOL(+) or (-) button to increase or decrease the volume.

Mute On/Off: Press briey to mute the sound. Press again to un-mute the sound.

Mode Sources: Press the MODE button to switch between AUX, FM, AM, Bluetooth (BT MUSIC).

Mode Settings (Bass/Treble/Balance/Fader/EQ/Loudness): Press the MODE button for

2 seconds and then press the button until the function you want is shown on the display.
Press VOL(+) (-) to change the settings of the menu item displayed.

2 sec.

BASS TRE BAL FAD

MODE

EQ LOUD

Bass (BAS)/Treble (TRE): Press the VOL(+) or (-) button to adjust Bass & Treble.

Balance (BAL): Press VOL(+) or (-) to adjust balance (sound distribution between the right and

left speakers).

Fader (FAD): Press VOL(+) or (-) to adjust sound distribution between the front and rear speakers.

Equalizer (EQ): Press VOL(+) or (-) to select one of the EQ options: OFF, FLAT, CLASS, POP,

ROCK, JAZZ, METAL. The equalizer will be disabled if EQ OFF is set. The equalizer setting is shown

at the bottom of the display.

Loudness (LOUD): Press VOL(+) or (-) (LOUD ON) or to disable the function (LOUD OFF). When
the loudness function is on, LOUD is shown on the right of the display.

Technical speci ications

TUNER FM Frequency
RangeChannelStep
Sensitivity
StereoSeparationSignal
toNoiseRatio

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV technician
for help.

87.5-107.9MHz

200kHz

2.8μV

30dB

50dB

The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.