SSV Works CM-FKP65 User Manual

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com | Phone: [phone] | Fax: [phone]

CM-FKP65

Commander and Maverick

6.5” Speaker Front Kick Panels

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects
in material or workmanship. All SSV Works Electronics are covered by a limited 1 year
warranty against defects in material or workmanship. All SSV Works Speakers are
covered by a limited 1 year warranty against defects in material or workmanship. Labor
for replacement of defective components is not covered. Contact SSV Works for further
warranty information.

TOOLS NEEDED FOR INSTALLATION

-Wire Crimpers

- Wire Strippers

- 5/32 Allen Wrench

- 7/16” Open End Wrench

- Drill with 1/8” and ¼” Drill bit

- #2 Phillips Screwdriver

- T-30 Torx wrench

- Scribe or Marker

PARTS LIST

1. CM2-FKP65-U Enclosures (1 pair)

2. 1/4” x 20 Allen Bolt x 6

!

Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.

3. 1/4” Washers x 6

4. 1/4” Nut x 6

PARTS LIST IMAGES

1. CM2-FKP65-U Enclosures
(1 pair)

2. 1/4 x 20 Allen Bolt x 6

3. 1/4” Washers x 6 4. 1/4” Nut x 6

INSTALLATION NOTES

The use of a thread locker is recommended on all screws to prevent loosening due to vibration. Sealing all wiring holes with a silicone sealer will
prevent moisture from entering the enclosure. The glove box does not need to be removed for Kick panel installation; ours was removed for photo
purposes only.

A

B

A. Align the kick panel above the foot rest and ush against the

rewall and outside of the vehicle (under the glove box on the
passenger side & mid way up the rewall on the driver side);

the enclosure is in the correct mounting location when it sits

ush on all sides. Using a scribe mark the 3 mounting holes.

C D

C. Drill a 1/4” hole in the enclosure for the speaker wire to run out

of, we recommend the at side toward the top of the enclosure.

B. After marking the holes, drill the mounting holes with the

1/4” drill.

D. Mount the enclosure into the vehicle using the supplied

hardware, putting the nut on the inside of the enclosure is
recommended. Removing the 4 - T-30 Torx along the side of
the vehicle will make this step easier.

E E

E. Place the speaker into the enclosure and mark the 4 mounting holes with a

scribe or marker, Pre-drill the marked mounting locations using a 1/8” drill bit.

CM-FKP65

F F

F. Connect and install the speaker into the enclosure using the #2 Phillips screwdriver (be sure to connect the “+” speaker wire to the

“+” terminal on the speaker and the “-“ speaker wire to the “-“ terminal on the speaker), repeat for other side.

G

G. Route the speaker wire away from any moving parts and any

sharp metal, then connect to the amplier.

WIRING INSTRUCTIONS

“+”

“-”

“+”

“-”

For proper sound, ensure the speaker polarity is correct connect the “+” to the “+” and the “-“to the “-“from the speaker wire to the amplier. If using with
an SSV Works complete system refer to the amplier wiring instructions for more detailed wiring information.

© 2017 SSV Works, Oxnard, CA 93030 CM-FKP65 Rev. B 4-10-17

“+”

“-”

“+”

“-”

CM-FKP65

Amplier