SSV Embedded Systems System-on-Module eSOM/2586 Hardware Reference Manual

System
on
Module
eSOM
/25
86
Board Revision 1.0
Hardware Reference
SSV Embedded Systems
Heisterbergallee 72 D-30453 Hannover Phone: +49 (0)511/40 000-0 Fax: +49 (0)511/40 000-40 E-mail: sales@ist1.de
Document Revision: 1.1
Date: 2009-04-07
F
OR FURTHER INFORMATION REGARDING OUR PRODUCTS PLEASE VISIT US AT WWW.SSV-EMBEDDED.DE
System-on-Module eSOM/2586 - Hardware Reference
2
Board R e vision 1.0 / Manual Re v i s ion 1.1
CONTENT
1 INTRODUCTION...............................................................................................................3
1.1 Safety Guidelines...................................................................................................................3
1.2 Conventions...........................................................................................................................3
1.3 Block Diagram.......................................................................................................................4
1.4 Features and Technical Data..................................................................................................5
2 BOARD LAYOUT ..............................................................................................................6
3 PINOUTS ..........................................................................................................................7
3.1 2 x 100 Pin Connector – J1 (1. Part)......................................................................................7
3.2 2 x 100 Pin Connector – J1 (2. Part)......................................................................................8
3.3 2 x 100 Pin Connector – J1 (3. Part)......................................................................................9
3.4 2 x 100 Pin Connector – J2 (1. Part)....................................................................................10
3.5 2 x 100 Pin Connector – J2 (2. Part)....................................................................................11
3.6 2 x 100 Pin Connector – J2 (3. Part)....................................................................................12
3.7 CompactFlash Card Slot – J3 (1. Part) ................................................................................13
3.8 CompactFlash Card Slot – J3 (2. Part) ................................................................................14
3.9 ISP/Test Connector – J4 ......................................................................................................15
3.11 RCM Jumper – JP1..............................................................................................................16
4 MEMORY MAP ...............................................................................................................17
4.1 System Memory Map ..........................................................................................................17
4.2 System I/O Map...................................................................................................................17
5 MECHANICAL DIMENSIONS .........................................................................................18
6 HELPFUL LITERATURE.................................................................................................19
CONTACT..............................................................................................................................19
DOCUMENT HISTORY .........................................................................................................19
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
3
1 INTRODUCTION
This document describes the hardware components of the System-on-Module eSOM/2586. For further information about the individual components of this product you may follow the links from our website at http://www.ssv-embedded.de. Our website contains a lot of technical information, which will be updated in regular periods.
1.1 Safety Guidelines
Please read the following safety guidelines carefully! In case of property or personal damage by not paying attention to this document and/or by incorrect handling, we do not assume liability. In such cases any warranty claim expires.
ATTENTION: Observe precautions for handling – electrostatic sensitive device!
Discharge yourself before you work with the device, e.g. by touching a heater of
metal, to avoid damages.
Stay grounded while working with the device to avoid damage through electrostatic
discharge.
1.2 Conventions
Convention Usage
bold
Important terms
italic
Filenames, user inputs and command lines
monospace
Pathnames, internet addresses and program code
Table 1: Conventions used in this Document
System-on-Module eSOM/2586 - Hardware Reference
4
Board R e vision 1.0 / Manual Re v i s ion 1.1
1.3 Block Diagram
The System-on-Module eSOM/2586 comes with 1 x 10/100 Mbps Ethernet LAN interface, 16-bit GPIO, 1 x SPI, 3 x UART, 18-bit VGA TTL LCD and 4-wire Touch Screen Interface, 1 x CompactFlash (CF) card slot and 2 x USB 2.0 host port. The 16-bit expansion bus inter­face (available over the 2 x 100 pin interface connector) supports the connection to external I/O chips and memory devices. The main application area of the eSOM/2586 is the field of embedded IP-based HMI (Human-Machine Interface) gateways for modern factory auto­mation and laboratory environments.
The eSOM/2586 drive space for the operating system and the user files are implemented with a NAND flash controller and a NAND flash chip. The eSOM/2586 NAND flash con­troller is connected to one of the USB 2.0 host controller of the Vortex86DX 32-bit x86 SoC. This means the eSOM/2586 is using an on-board USB boot device.
Figure 1: Block diagram of System-on-Module eSOM/2586
The main component of the eSOM/2586 is the Vortex86DX 32-bit x86 SoC (System on Chip). The Vortex86DX is a high performance MCU, which is compatible with DOS, Linux and Microsoft Windows CE. It integrates 32 KB write through direct map L1 cache, PCI Rev. 2.1 32-bit bus interface at 33 MHz, DDR2 SDRAM controller, ROM controller, IPC (Internal Peripheral Controller) with DMA and interrupt timer/counter, Fast Ethernet MAC and PHY, 16C550/16C552-compatible FIFO UART, USB 2.0 Host controller and many more. Please see the Vortex86DX user manuals for more details.
The eSOM/2586 VGA Graphics Controller is implemented with a XGI Volari Z9s GPU (Graphics Processing Unit) and 64 MByte DDR2-based Frame Buffer RAM. The Z9s GPU device is using an on-board PCI bus interface to the Vortex86DX SoC.
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
5
1.4 Features and Technical Data
Vortex86DX 32-bit x86 SoC @600, 800, 1.000 MHz Clock Speed (please see note 1)
PC-compatible AMI Basic I/O System (BIOS)
128 MByte SDRAM with DDR2 interface @300 MHz Bus Speed
1 GByte NAND FLASH Memory for O/S Boot Image and Data Files
XGI GPU VGA controller with 64 MByte Frame Buffer (DDR2 SDRAM)
On-board PCI Interface between Vortex86DX SoC and XGI GPU
18-bit TTL Color LCD Interface for TFT and STN panels
4-wire Touch Screen Interface (please see note 2)
1x CompactFlash (CF) Card Slot with IDE-based Interface
1x LED for IDE (CF) Access Status
1x 10/100 Mbps Ethernet LAN Interface
1x LED Output Signal for LAN Status
2x USB 2.0 Host Interface with HS, FS and LS support
1x SPI (Serial Peripheral Interface) with one Chip Select Output (please see note 3)
3x 16C550/16C552-compatible UART-based Serial Ports (one with all Handshakes)
16-bit General Purpose Parallel Input Output (GPIOs) (please see note 3)
16-bit Expansion Bus with 24 Address Lines
4x Interrupt Inputs, 4x Chip Select Outputs
Programmable Watchdog Timer
In-System Programming Features
2x 100-pin Hirose FX8C Interface Connector
3.3 Volt Low Power Design, Supply Voltage 3.3 VDC (±5 %)
Supply Current 1.000 mA typ. @800 MHz (1.300 mA max.)
0 °C to +70 °C Operating Temperature (still air) without Heat Sink
Size 80 mm x 50 mm
Preinstalled Linux O/S with Kernel Version 2.6.18 or ROM-DOS 6.22 O/S
RoHS compliant
Note 1: The ex factory clock speed is 800 MHz. The other clock speeds are available over an on-board strap option.
Note 2: The software interface of the eSOM/2586 4-wire touch screen interface is available over an on-board UART.
Note 3: The four SPI signals of the eSOM/2586 can be also used as a 4-bit GPIO (GPIO – Parallel Port C).
System-on-Module eSOM/2586 - Hardware Reference
6
Board R e vision 1.0 / Manual Re v i s ion 1.1
2 BOARD LAYOUT
Figure 2: Board layout System-on-Module eSOM/2586
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
7
3 PINOUTS
3.1 2 x 100 Pin Connector – J1 (1. Part)
Pin Name Group Function
1
VCC PWR 3.3 Volt Power Input
2
VCC PWR 3.3 Volt Power Input
3
PA0 GPIO GPIO - Parallel Port A, Bit 0
4
PA4 GPIO GPIO - Parallel Port A, Bit 4
5
PA1 GPIO GPIO - Parallel Port A, Bit 1
6
PA5 GPIO GPIO - Parallel Port A, Bit 5
7
PA2 GPIO GPIO - Parallel Port A, Bit 2
8
PA6 GPIO GPIO - Parallel Port A, Bit 6
9
PA3 GPIO GPIO - Parallel Port A, Bit 3
10
PA7 GPIO GPIO - Parallel Port A, Bit 7
11
GND PWR Ground
12
GND PWR Ground
13
--- --- Not Connected – Reserved. Do not use.
14
--- --- Not Connected – Reserved. Do not use.
15
--- --- Not Connected – Reserved. Do not use.
16
--- --- Not Connected – Reserved. Do not use.
17
--- --- Not Connected – Reserved. Do not use.
18
SPICS0 SIO Serial I/O, SPI Interface Chip Select 0
19
--- --- Not Connected – Reserved. Do not use.
20
SPICLK SIO Serial I/O, SPI Interface Clock
21
--- --- Not Connected – Reserved. Do not use.
22
MOSI SIO Serial I/O, SPI Interface Master Out Slave In
23
--- --- Not Connected – Reserved. Do not use.
24
MISO SIO Serial I/O, SPI Interface Master In Slave Out
25
VCC PWR 3.3 Volt Power Input
26
VCC PWR 3.3 Volt Power Input
27
INT4 EXPBUS Expansion Bus, Interrupt Input 4
28
CLKOUT EXPBUS Expansion Bus, Clock Output
29
INT3 EXPBUS Expansion Bus, Interrupt Input 3
30
RDY EXPBUS Expansion Bus, External Ready Input
31
INT2 EXPBUS Expansion Bus, Interrupt Input 2
32
WR EXPBUS Expansion Bus, Write Signal
33
INT1 EXPBUS Expansion Bus, Interrupt Input 1
34
RD EXPBUS Expansion Bus, Read Signal
35
GND PWR Ground
36
GND PWR Ground
37
D0 EXPBUS Expansion Bus, Data Bit 0
38
D8 EXPBUS Expansion Bus, Data Bit 8
39
D1 EXPBUS Expansion Bus, Data Bit 1
40
D9 EXPBUS Expansion Bus, Data Bit 9
Table 2: Pinout 2 x 100 pin connector – pin 1 to 40
System-on-Module eSOM/2586 - Hardware Reference
8
Board R e vision 1.0 / Manual Re v i s ion 1.1
3.2 2 x 100 Pin Connector – J1 (2. Part)
Pin Name Group Function
41
D2 EXPBUS Expansion Bus, Data Bit 2
42
D10 EXPBUS Expansion Bus, Data Bit 10
43
D3 EXPBUS Expansion Bus, Data Bit 3
44
D11 EXPBUS Expansion Bus, Data Bit 11
45
VCC PWR 3.3 Volt Power Input
46
VCC PWR 3.3 Volt Power Input
47
D4 EXPBUS Expansion Bus, Data Bit 4
48
D12 EXPBUS Expansion Bus, Data Bit 12
49
D5 EXPBUS Expansion Bus, Data Bit 5
50
D13 EXPBUS Expansion Bus, Data Bit 13
51
D6 EXPBUS Expansion Bus, Data Bit 6
52
D14 EXPBUS Expansion Bus, Data Bit 14
53
D7 EXPBUS Expansion Bus, Data Bit 7
54
D15 EXPBUS Expansion Bus, Data Bit 15
55
GND PWR Ground
56
GND PWR Ground
57
A0 EXPBUS Expansion Bus, Address Bit 0
58
A1 EXPBUS Expansion Bus, Address Bit 1
59
A2 EXPBUS Expansion Bus, Address Bit 2
60
A3 EXPBUS Expansion Bus, Address Bit 3
61
A4 EXPBUS Expansion Bus, Address Bit 4
62
A5 EXPBUS Expansion Bus, Address Bit 5
63
A6 EXPBUS Expansion Bus, Address Bit 6
64
A7 EXPBUS Expansion Bus, Address Bit 7
65
VCC PWR 3.3 Volt Power Input
66
VCC PWR 3.3 Volt Power Input
67
A8 EXPBUS Expansion Bus, Address Bit 8
68
A9 EXPBUS Expansion Bus, Address Bit 9
69
A10 EXPBUS Expansion Bus, Address Bit 10
70
A11 EXPBUS Expansion Bus, Address Bit 11
71
A12 EXPBUS Expansion Bus, Address Bit 12
72
A13 EXPBUS Expansion Bus, Address Bit 13
73
A14 EXPBUS Expansion Bus, Address Bit 14
74
A15 EXPBUS Expansion Bus, Address Bit 15
75
GND PWR Ground
76
GND PWR Ground
77
A16 EXPBUS Expansion Bus, Address Bit 16
78
A17 EXPBUS Expansion Bus, Address Bit 17
79
A18 EXPBUS Expansion Bus, Address Bit 18
80
A19 EXPBUS Expansion Bus, Address Bit 19
Table 3: Pinout 2 x 100 pin connector – pin 41 to 80
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
9
3.3 2 x 100 Pin Connector – J1 (3. Part)
Pin Name Group Function
81
A20 EXPBUS Expansion Bus, Address Bit 20
82
A21 EXPBUS Expansion Bus, Address Bit 21
83
A22 EXPBUS Expansion Bus, Address Bit 22
84
A23 EXPBUS Expansion Bus, Address Bit 23
85
--- --- Not Connected – Reserved. Do not use.
86
--- --- Not Connected – Reserved. Do not use.
87
VCC PWR 3.3 Volt Power Input
88
VCC PWR 3.3 Volt Power Input
89
CS1 EXPBUS Chip Select Output 1
90
CS3 EXPBUS Chip Select Output 3
91
CS2 EXPBUS Chip Select Output 2
92
CS4 EXPBUS Chip Select Output 4
93
VBATP PWR 3 Volt Real Time Clock Battery Plus Input
94
--- --- Not Connected – Reserved. Do not use.
95
--- --- Not Connected – Reserved. Do not use.
96
RESOUT RESET Reset Output Signal
97
--- --- Not Connected – Reserved. Do not use.
98
RESIN RESET Reset Input Signal
99
GND PWR Ground
100
GND PWR Ground
Table 4: Pinout 2 x 100 pin connector – pin 81 to 100
System-on-Module eSOM/2586 - Hardware Reference
10
Board R e vision 1.0 / Manual Re v i s ion 1.1
3.4 2 x 100 Pin Connector – J2 (1. Part)
Pin Name Group Function
101
VCC PWR 3.3 Volt Power Input
102
VCC PWR 3.3 Volt Power Input
103
CTS1 SIO Serial I/O, UART COM1 CTS Pin
104
--- --- Not Connected – Reserved. Do not use.
105
TXD1 SIO Serial I/O, UART COM1 TXD Pin
106
--- --- Not Connected – Reserved. Do not use.
107
RXD1 SIO Serial I/O, UART COM1 RXD Pin
108
--- --- Not Connected – Reserved. Do not use.
109
RTS1 SIO Serial I/O, UART COM1 RTS Pin
110
--- --- Not Connected – Reserved. Do not use.
111
GND PWR Ground
112
GND PWR Ground
113
RI1 SIO Serial I/O, UART COM1 RI Pin
114
--- --- Not Connected – Reserved. Do not use.
115
DTR1 SIO Serial I/O, UART COM1 DTR Pin
116
LANLED1 LAN 10/100 Mbps Ethernet LAN Interface LAN1 LED Output
117
DSR1 SIO Serial I/O, UART COM1 DSR Pin
118
--- --- Not Connected – Reserved. Do not use.
119
DCD1 SIO Serial I/O, UART COM1 DCD Pin
120
--- --- Not Connected – Reserved. Do not use.
121
VCC PWR 3.3 Volt Power Input
122
VCC PWR 3.3 Volt Power Input
123
CTS2 SIO Serial I/O, UART COM2 CTS Pin
124
--- --- Not Connected – Reserved. Do not use.
125
TXD2 SIO Serial I/O, UART COM2 TXD Pin
126
--- --- Not Connected – Reserved. Do not use.
127
RXD2 SIO Serial I/O, UART COM2 RXD Pin
128
--- --- Not Connected – Reserved. Do not use.
129
RTS2 SIO Serial I/O, UART COM2 RTS Pin
130
--- --- Not Connected – Reserved. Do not use.
131
GND PWR Ground
132
GND PWR Ground
133
HDN1 SIO Serial I/O, USB Host1 Port- Pin
134
LRXN1 LAN 10/100 Mbps Ethernet LAN Interface LAN1, RX- Pin
135
HDP1 SIO Serial I/O, USB Host1 Port+ Pin
136
LRXP1 LAN 10/100 Mbps Ethernet LAN Interface LAN1, RX+ Pin
137
HDN2 SIO Serial I/O, USB Host2 Port- Pin
138
LTXN1 LAN 10/100 Mbps Ethernet LAN Interface LAN1, TX- Pin
139
HDP2 SIO Serial I/O, USB Host2 Port+ Pin
140
LTXP1 LAN 10/100 Mbps Ethernet LAN Interface LAN1, TX+ Pin
Table 5: Pinout 2 x 100 pin connector – pin 101 to 140
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
11
3.5 2 x 100 Pin Connector – J2 (2. Part)
Pin Name Group Function
141
GND PWR Ground
142
GND PWR Ground
143
--- --- Reserved. Do not use.
144
--- --- Reserved. Do not use.
145
LCDB5 PSP LCD Interface, Blue Data Bit 5
146
LCDB4 PSP LCD Interface, Blue Data Bit 4
147
LCDB3 PSP LCD Interface, Blue Data Bit 3
148
LCDB2 PSP LCD Interface, Blue Data Bit 2
149
LCDB1 PSP LCD Interface, Blue Data Bit 1
150
LCDB0 PSP LCD Interface, Blue Data Bit 0
151
VCC PWR 3.3 Volt Power Input
152
VCC PWR 3.3 Volt Power Input
153
--- --- Reserved. Do not use.
154
--- --- Reserved. Do not use.
155
LCDG4 PSP LCD Interface, Green Data Bit 4
156
LCDG5 PSP LCD Interface, Green Data Bit 5
157
LCDG2 PSP LCD Interface, Green Data Bit 2
158
LCDG3 PSP LCD Interface, Green Data Bit 3
159
LCDG0 PSP LCD Interface, Green Data Bit 0
160
LCDG1 PSP LCD Interface, Green Data Bit 1
161
GND PWR Ground
162
GND PWR Ground
163
--- --- Reserved. Do not use.
164
--- --- Reserved. Do not use.
165
LCDR5 PSP LCD Interface, Red Data Bit 5
166
LCDR4 PSP LCD Interface, Red Data Bit 4
167
LCDR3 PSP LCD Interface, Red Data Bit 3
168
LCDR2 PSP LCD Interface, Red Data Bit 2
169
LCDR1 PSP LCD Interface, Red Data Bit 1
170
LCDR0 PSP LCD Interface, Red Data Bit 0
171
VCC PWR 3.3 Volt Power Input
172
VCC PWR 3.3 Volt Power Input
173
LCDHS PSP LCD Interface, HSYNC Signal (Horizontal Sync Output)
174
LCDVS PSP LCD Interface, VSYNC Signal (Vertical Sync Output)
175
LCDDE PSP LCD Interface, Data Enable Signal
176
LCDPCLK PSP LCD Interface, Pixel Clock
177
LCDPC PSP LCD Interface, Power Control Output (VDD Enable)
178
LCDBLC PSP LCD Interface, Backlight Control Output (On/Off)
179
GND PWR Ground
180
GND PWR Ground
Table 6: Pinout 2 x 100 pin connector – pin 141 to 180
System-on-Module eSOM/2586 - Hardware Reference
12
Board R e vision 1.0 / Manual Re v i s ion 1.1
3.6 2 x 100 Pin Connector – J2 (3. Part)
Pin Name Group Function
181
PB4 GPIO GPIO - Parallel Port B, Bit 4
182
PB0 GPIO GPIO - Parallel Port B, Bit 0
183
PB5 GPIO GPIO - Parallel Port B, Bit 5
184
PB1 GPIO GPIO - Parallel Port B, Bit 1
185
PB6 GPIO GPIO - Parallel Port B, Bit 6
186
PB2 GPIO GPIO - Parallel Port B, Bit 2
187
PB7 GPIO GPIO - Parallel Port B, Bit 7
188
PB3 GPIO GPIO - Parallel Port B, Bit 3
189
VCC PWR 3.3 Volt Power Input
190
VCC PWR 3.3 Volt Power Input
191
TSYN PSP Touch Screen Interface, Y- Position Input
192
CTS3 SIO Serial I/O, UART COM3 CTS Pin
193
TSYP PSP Touch Screen Interface, Y+ Position Input
194
TXD3 SIO Serial I/O, UART COM3 TXD Pin
195
TSXN PSP Touch Screen Interface, X- Position Input
196
RXD3 SIO Serial I/O, UART COM3 RXD Pin
197
TSXP PSP Touch Screen Interface, X+ Position Input
198
RTS3 SIO Serial I/O, UART COM3 RTS Pin
199
GND PWR Ground
200
GND PWR Ground
Table 7: Pinout 2 x 100 pin connector – pin 181 to 200
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
13
3.7 CompactFlash Card Slot – J3 (1. Part)
Pin Name Function
1
GND Ground
2
D3 Data Bit 3
3
D4 Data Bit 4
4
D5 Data Bit 5
5
D6 Data Bit 6
6
D7 Data Bit 7
7
CS0# Chip Select 0
8
A10 Not Connected
9
ATASEL# Ground
10
A9 Not Connected
11
A8 Not Connected
12
A7 Not Connected
13
VCC 3.3 VDC Power
14
A6 Not Connected
15
A5 Not Connected
16
A4 Not Connected
17
A3 Not Connected
18
A2 Address Bit 2
19
A1 Address Bit 1
20
A0 Address Bit 0
21
D0 Data Bit 0
22
D1 Data Bit 1
23
D2 Data Bit 2
24
IOCS16# Not Connected
25
CD2# Connected to Ground
Table 8: Pinout CompactFlash card slot – pin 1 to 25
System-on-Module eSOM/2586 - Hardware Reference
14
Board R e vision 1.0 / Manual Re v i s ion 1.1
3.8 CompactFlash Card Slot – J3 (2. Part)
Pin Name Function
26
CD1 Connected to Ground
27
D11 Data Bit 11
28
D12 Data Bit 12
29
D13 Data Bit 13
30
D14 Data Bit 14
31
D15 Data Bit 15
32
CS1# Chip Select 1
33
VS1# Connected to Ground
34
IOR# Read Strobe
35
IOW# Write Strobe
36
WE# Not Connected
37
INTRQ Interrupt Request
38
VCC 3.3 VDC Power
39
CSEL# Cable Select (Jumpered as Master)
40
VS2# Not Connected
41
RESET# Reset Pin
42
IORDY I/O Ready
43
DMARQ DMA Request
44
DMACK# DMA Acknowledge
45
DASP# Device Active or Slave Present (CF LED)
46
PDIAG# Passed Diagnostics
47
D8 Data Bit 8
48
D9 Data Bit 9
49
D10 Data Bit 10
50
GND Ground
Table 9: Pinout CompactFlash card slot – pin 26 to 50
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
15
3.9 ISP/Test Connector – J4
Pin Name Function
1
VCC 3.3 VDC
2
GND Ground
3
--- Reserved
4
FS1 Reserved for Factory Setup
5
FS2 Reserved for Factory Setup
6
--- Reserved
7
FS3 Reserved for Factory Setup
8
FS4 Reserved for Factory Setup
9
--- Reserved
10
FS5 Reserved for Factory Setup
11
FS6 Reserved for Factory Setup
12
--- Reserved
13
FS7 Reserved for Factory Setup
14
--- Reserved
15
--- Reserved
16
--- Reserved
17
FS8 Reserved for Factory Setup
18
VCC 3.3 VDC
Table 10: Pinout ISP/Test connector
System-on-Module eSOM/2586 - Hardware Reference
16
Board R e vision 1.0 / Manual Re v i s ion 1.1
3.10 RCM Jumper – JP1
The RCM (Remote Console Mode) offers the possibility to control the eSOM/2586 via a terminal emulation program over the UART-based serial port COM1 (serial­based CLI = Command Line Interface).
Please note: The default setting of the RCM jumper is set (Enable Remote Console Mode). This mode is checked by the AMI Basic I/O System (BIOS). With RCM jumper set, it is possible to control a DOS O/S over COM1. DOS I/O goes direct over the AMI BIOS I/O functions.
To disable RCM remove the jumper cap of the RCM jumper. This frees UART based serial port COM1 for application usage.
RCM jumper Function
Not set Disable Remote Console Mode Set (default) Enable Remote Console Mode
Table 11: RCM jumper settings
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
17
4 MEMORY MAP
4.1 System Memory Map
Physical Address Range Description Access Format Type
0x0000.0000 - 0x000F.FFFF 1 MByte DOS/BIOS Area 16-bit MEM R/W MEM 0x0010.0000 - 0x03FF.FFFF 63 MByte Main Memory 16-bit MEM R/W MEM 0xF800.0000 - 0xFBFF.FFFF 64 MByte Frame Buffer 16-bit MEM R/W MEM
Table 12: System memory map of System-on-Module eSOM/2586
4.2 System I/O Map
Physical Address Range Description Access Format Type
0x000 - 0x3FF IO Address Space * * 0x078 GPIO Port A Data Register 8-bit IO R/W * 0x079 GPIO Port B Data Register 8-bit IO R/W * 0x07B GPIO Port C Data Register 8-bit IO R/W * 0x098 GPIO Port A Direction Register 8-bit IO R/W * 0x099 GPIO Port B Direction Register 8-bit IO R/W * 0x09B GPIO Port C Direction Register 8-bit IO R/W * 0x100 - 0x10F Chip Select Signal CS1# 8-bit IO R/W GPCS1 0x110 - 0x11F Chip Select Signal CS2# 8-bit IO R/W GPCS1 0x120 - 0x12F Chip Select Signal CS3# 8-bit IO R/W GPCS1 0x130 - 0x13F Chip Select Signal CS4# 8-bit IO R/W GPCS1
Table 13: External I/O map of System-on-Module eSOM/2586
* Refer to Vortex86DX manual.
System-on-Module eSOM/2586 - Hardware Reference
18
Board R e vision 1.0 / Manual Re v i s ion 1.1
5 MECHANICAL DIMENSIONS
All length dimensions have a tolerance of 0.5 mm. The drillings are suitable for M2 screws.
Figure 3: Mechanical dimensions of System-on-Module eSOM/2586
System-on-Module eSOM/2586 - Hardware Reference
Board R e vision 1.0 / Manual Re v i s ion 1.1
19
6 HELPFUL LITERATURE
Vortex86DX documents: http://www.vortex86dx.com
BB6/eSOM hardware reference
CONTACT
SSV Embedded Systems
Heisterbergallee 72 D-30453 Hannover Phone: +49 (0)511/40 000-0 Fax: +49 (0)511/40 000-40 E-mail: sales@ist1.de Internet: www.ssv-embedded.de Support: www.ssv-comm.de/forum
DOCUMENT HISTORY
Revision Date Remarks Name
1.0 2009-03-24 First version WBU
1.1 2009-04-07 Errors in chapter 1.4 corrected WBU
The content of this document can change any time without an
nouncement. There is taken over no guarantee
for the accuracy of the statements. The user assumes the entire risk as to the accuracy and the use of this
document. Information in this d
ocument is provided ‘as is’ without warranty of any kind. Some names within
this document can be trademarks of their respective holders.
© 2009 SSV EMBEDDED SYSTEMS. All rights reserved.
Loading...