SSS Siedle PUMA X Owner's Manual

MODEL:PUMA X 3-SPEED AIR MOVER

shown with optional transport kit

FOR YOUR CONVENIENCE, RECORD THE FOLLOWING
IMPORTANT INFORMATION

MODEL:

SERIAL NUMBER:

DATE PURCHASED:

PURCHASED FROM:

VV78112TR

REV.2016(08.08)

Warranty Information

Please contact your Triple S Distributor for a copy of the
current warranty for this machine.

1

FIGURE 1

FIGURE 2

2

FIGURE 3

3

17

FIGURE 4

16

15

1

14

13

12

2

11

10

3

4

5

6

4

7

8

9

pPUMA X PART LIST

FIGURE 5

DIA NO PART NUMBER PART DISCRIPTION QTY

1 VV78200 MOTOR SIDE VENT COVER KIT 1
2 VV78106 FAN WHEEL KIT 1

VV78201 120V MOTOR ASSEMBLY KIT 1

3

4 VV78202 REAR RUBBER FOOT KIT 1
5 VV78203 KICK STAND 1
6 VV78204 FRONT SUPPORTING FOOT KIT 1

7 VV78205 FRONT OUTLET VENT KIT 1

8 VV78206 WATERPROOF COVER KIT 1
9

VV78207 CONTROL PLATE KIT 1
10 VV78014 SOCKET 1
11 VV78210 3 SPEED CONTROL KNOB KIT 1
12 VV78211 3 SPPED SWITCH 1
13 VV78019 CIRCUIT BREAKER 1
14 VV78212 OUTER HOUSING KIT 1
15 VV78213 FAN WHEEL SIDE VENT COVER KIT 1
16 VV78214 US POWER CORD 1
17 VV78406 ttt TRANSPORT KIT(OPTIONAL PART) 1

W i r in g D i a g r a m

B l a c k

G r e e n

W h i te

(Figure6)

C i r cu i t B r e a k e r

O F F

R o t a ry
S w i tc h

T . P .

1

2

3

C a p a c i to r

PUMA X Circuit Connection Diagram

1 1 0 ~ 1 2 0 V
6 0 H z
S i n g le
P h a s e
P o w e r
S u p p l y

S J T W 1 4 / 3 C P o w e r S u p p l y C o r d

1/3HP Air Blower Specification(Figur7e 7 )7

Sound

Voltage

Model No.

PUMA X 120V 60 1/3HP 3.7/3.8/4.0 64/68/72 1000/1200/1400 2000/2200/2400 405X402X468 10

Frequency

(V)

(Hz)

Power

(W)

Amp Draw
(L/M/H)A

Level

(L/M/H)

dBA

Motor Speed

(L/M/H)

rpm

Air flow

((L/M/H))

CFM

7

Shipping

Dimension

(mm)

Shipping

Weight

5

(kg)

SAFETY PRECAUTIONS

ENGLISH OPERATING INSTRUCTIONS

All operators shall read, understand and exercise the following safety precautions:

1) Do not operate machine:

 Unless trained and authorized.

 Unless you have read and understand the operators manual.

 Inflammable or explosive areas.

 With a damaged cord or plug.

 If not in proper operating condition.

 In outdoor areas.

 In standing water.

 With the use of extension cords.

2) Before operating machine:

 Make sure all safety devices are in place and operate properly.

3) When using machine:

 Do not pull machine by cord or plug.

 Do not pull cord around sharp edges or corners.

 Do not unplug machine by pulling on the cord.

 Do not stretch cord.

 Do not handle plug with wet hands.

 Keep cord away from heated surfaces.

 Report machine damage or faulty operation immediately.

4) Before leaving or servicing machine:

 Turn off machine.

 Unplug cord from outlet.

5) When servicing machine:

 An experienced technician should only perform service work.

 Unplug cord from outlet.

 Use manufacturer supplied or approved replacement parts.

6

GROUNDING INSTRUCTIONS

ENGLISH OPERATING INSTRUCTIONS

General – This air mover shall be grounded while in use to protect the operator from electrical
shock. The machine is provided with a three – conductor cord and a three – contact grounding
attachment plug to fit the proper grounding ty

pe receptacle.

type

The green (or green & yellow) conductor in the cord is the grounding wire. Never connect this wire to
anything other than the grounding pin of the attachment plug.
Make sure that all the safety functions are normal, and ensure that the actual operation voltage is in
accordance with the required voltage rate.Make sure that the machine is connected to an outlet
having the same configuration as the plug. No adapter should be used with this machine.
This machine is intended for commercial use only. It is constructed for use in an indoor environment
and is not intended for any other use.

BASIC OPERATION

1) Check the machine for any obstructions in fan pri

or to operation.

• If an item blocks the intakes of the air mover, this will hurt the performance of the machine,

and could cause the motor to overheat.

2) Adjust machine to desired position for operation

adjustments.(Air blower drying direction without Transport kit refer to

by pulling it back to its preset height

Figure 1

)

3) Plug power cord into a grounded outlet.

• Do not use an extension cord in conjunction with the standard power cord.

4) This machine has 3 power settings. Turn the power

knob to the desired speed.

• Low = 1 Med = 2 High = 3.

5) To stop the machine at any time, simply turn the

power knob to the “off” position.

• Never stick any object into the air inlet vents or the air outlet vent.

DAISY CHAIN

The can be connected in a “Daisy Chain” allowing for t wo aditional

PUMA X PUMA X

work together on one circuit

refer to .

Figure 2

units to

NOTE: The Air Mover has an onboard circuit breaker. If the auxiliary outlet overloads, the circuit
breaker will trip. If the breaker trips, unplug the units and press the circuit breaker reset button. Plug
the units back into the power source and turn on the switch.

7

MAINTENANCE

ENGLISH OPERATING INSTRUCTIONS

To keep this machine performing well for many years, please follow the following maintenance

procedures:

Always confirm the machine is unplugged from the power source prior to performing

any maintenance or repairs!

1) Unplug machine as soon as you are done using it.

2) Check power cord for any damage. If any damage is detected, replace the cord immediately.

3) Lubricate the handle assembly and wheels with a water resistant lubricant every month.

4) Check machine for loose or missing nuts and bolts, and replace as necessary.

5) Clean the outside of the machine with a mild cleaner.

PART LIST

refer to

Figure 4+ 5

Figure 6

PUMA X

WIRING DIAGRAM

PUMA X

part list drawing refer to

wiring diagram

AIR BLOWER SPECIFICATION

Air blower specification refer to

Figure 7

8