SSS AF9 User Manual
Serial
Number______________________________
(Located on bottom of cleaner as shown)
AF9 Commercial
Clean-Air
Turbo Power
Review these instructions
before operating cleaner
Important Safeguards!
When using an electrical appliance, always follow basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
Warning:To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Connect to a properly grounded outlet only. See “Grounding Instructions”.
• Close supervision is necessary when any appliance is used by or near children. Do
not allow vacuum cleaner to be used as a toy or to run unattended at any time.
• Keep hair, loose clothing, fingers, feet and all parts of body away from openings,
rotating agitator and other moving parts. Do not operate cleaner in bare feet or
when wearing open toe shoes or sandals.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
• Do not use to pick up flammable or combustible liquids such as gasoline or fine
wood sandings or use in areas where they may be present.
• Avoid picking up hard, sharp objects with the cleaner. They may damage the
cleaner and the bag.
• Always turn off this appliance before connecting or disconnecting hose.
• Do not use without dust bag or filters in place. Change bag frequently when
picking up very fine materials such as powder.
• Use extra care when cleaning on stairs.
• Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, or anything that may reduce air flow.
• Do not pull or carry by cord, use cord as a handle, close door on cord or pull
cord around sharp edges or corners. Do not run appliance over cord. Keep cord
away from heated surfaces.
• Always disconnect cord from electrical outlet before servicing the cleaner.
• Unplug cleaner when not in use. Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord. Never handle plug or appliance with wet hands.
• The use of an extension cord is not recommended.
• Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, take it to a
Triple S Authorized Dealer.
• Use vacuum cleaner only for its intended use as described in the instructions.
Use only attachments recommended by Triple S; others may cause hazards.
Save these instructions!
Index
Assembling Cleaner ..........................2-3
Cleaner Descriptions ............................4
How To Use
Cleaning Tools ..................................6
Upright Cleaner ..............................5-6
If You Have a Problem ........................11
Important Safeguards ..........................1
Maintenance
Authorized Service..........................12
Cleaning Filters..................................8
Lubrication ......................................12
Clearing Blockages ........................11
Emptying Cloth Bag ......................6-7
Replacing Agitator ..........................10
Replacing Belt ..............................9-10
Replacing Edge Groomers ............10
Replacing Headlight..........................9
Replacing Paper Bag ........................8
Thermal Protector ..............................11
Unpacking Cleaner................................4
© 2003
OPERATING INSTRUCTIONS
ENGLISH ➜ pp. 1-12
ESPAÑOL ➜ pp. 13-18
FRANÇAIS
➜ pp. 19-24
Push bolts into holes on back
of handle.
4
Slide handle onto cleaner body.
Remove bag door on cleaner
body by pushing down at top
of door and pulling door outward.
2
STEP I Unpack carton
Remove all parts from carton
and identify each item shown.
Make sure all parts are located
before disposing of packing.
A. Handle section
B. Cleaner body
C. Hose, cleaning tools and wands
D. Handle bolts and nuts packet
(in bag with operating instructions)
A
B
C
D
E
F
Not required for assembly:
E. Optional Paper filter bag
(Cloth bag already installed in cleaner)
F. Extra belt
(One already installed in cleaner)
STEP II Attach handle
1
1
2
2
3
4
3
Lift hose tube cover (C).
Position hose over hose hook
(D) and onto hose tube (E).
Slide hose into (B) and twist
hose to lock it into place.
Align end of hose with projections (A) over slots (B) in dirt
duct.
Reposition bag door by fitting
tabs on bottom of door into
opening. Press top of door to snap
securely shut.
Place nuts in recessed areas
on front of handle. Hold each
nut in place while tightening each
bolt securely with a Phillips screw
driver.
3
5
7
9
9
8
7
6
5
A
B
B
C
D
E
8
10
11
STEP III Attach Hose
STEP IV Position Tools
A
B
C
6
NOTE: HOSE MUST BE CONNECTED AS SHOWN
FOR ALL OPERATIONS
Place smaller unridged end of
wand into bottom of rack. Snap
wand into clip. Repeat with other
wand.
Position dusting brush (A) and
furniture nozzle (B) into areas
as shown. Place crevice wand (C)
inside extension wand.
10
11
should be used only until a properly
grounded outlet (B) can be installed by a
qualified electrician. The green colored
rigid ear, lug, or the like (F) extending from
the adapter must be connected to a permanent ground (G) such as a properly
grounded outlet box cover. Whenever the
adapter is used, it must be held in place
by a metal screw.
Note: In Canada, the use of a temporary adapter is not permitted by the
Canadian Electrical Code.
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the appliance - if it will not fit the
outlet have a proper outlet installed by a
qualified electrician. This appliance is for
use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug
illustrated in sketch (A).
A temporary adapter (D) may be
used to connect this plug to a 2-pole
receptacle (E) if a property grounded outlet
is not available. The temporary adapter
4
12
13
14
14
Cleaner description
How to use
The assembled cleaner will
look like the drawing.
1. Handle
2. Cord hooks: wrap cord around
hooks for storage. The top hook can
be rotated right or left for easy cord
release.
3. Hose
4. ON/OFF Switch: located on left
rear corner of cleaner body.
5. Carrying handle
6. Bag door
7. Stair cleaning handle:
located
on lower edge of bag door.
8. Handle release lever: step on
lever to lower to operating or low
positions.
9. Headlight
10. Nozzle control knob: slide
knob to correct setting for height of
carpet being cleaned.
11. Furniture guard: helps prevent
cleaner from marking furniture.
12. Edge groomers
13. Wands
14. Final exhaust filter
15. Dusting brush
16. Crevice wand: stores inside of
extension wand.
17. Furniture nozzle
18. Hose hook
1
2
2
2
3
4
5
6
7
9
10
11
12
17
18
14
15
16
Operate cleaner only at voltage
specified on data plate on bottom
of cleaner.
WARNING: Electric shock could
occur if used outdoors or on wet
surfaces
Grounding instructions
This appliance must be grounded. If
it should malfunction or breakdown,
grounding provides a path of least
resistance for electrical current to reduce
the risk of electric shock. This appliance is
equipped with a cord having an equipment-grounding conductor (C) and
grounding plug (A). The plug must be
plugged into an appropriate outlet (B) that
is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER –
Improper connection of the equipmentgrounding conductor can result in the risk
of electric shock. Check with a qualified
C
F
G
A
B
D
E
13
13
12
8
For maximum cleaning performance, the following carpet
height settings are recommended.
• Lowest setting: for all types of carpet
• Higher settings: for very deep pile
carpet where easier pushing effort is
desired, while maintaining good
cleaning performance.
Edge cleaning
Special edge groomers are pro-
vided on both sides of the nozzle
to remove dirt in carpet near baseboards and furniture. Guide either side
of nozzle parallel to edge of carpet or
furniture.
For ease in sliding knob, the
handle should be in the upright
position (C).
The nozzle will not move into the
adjusted position until the cleaner
handle is lowered to the operating
position (D).
The cleaning of carpet and rugs
takes place at the nozzle (A).
When it is necessary to raise and
lower the nozzle for various carpet
pile heights, slide the nozzle control
knob (B) to the desired setting.
The cleaner can also be moved
by using carrying handle.
Transporting cleaner
To move your cleaner from
room to room, put handle in
upright position, tilt cleaner back on
rear wheels and push forward.
Handle Positions
The handle of your cleaner has
three positions; upright for
storage and when using cleaning
tools; operating position for general operation on carpet and floors;
low for reaching under low furniture.
Step on handle release lever to
lower handle.
Plug cord into electrical outlet.
To turn cleaner ON, push
switch (A) toward front of cleaner.
To turn cleaner OFF, push (A) toward
back of cleaner.
5
15
15
16
17
18
19
20
21
22
22
21
20
19
18
17
16
A
A
C
D
B
HIGH
BARE
FLOOR
Carpet height adjustment
Note: If the cleaner is difficult to push,
slide knob to the next higher setting.
Attach wand and
tools
When using cleaning tools, cleaner
should be in upright position.
Also, turn cleaner OFF before disconnecting and connecting hose
to hose tube (A).
To use hose, lift hose end as
shown. Lower cover (B) on
hose tube.
When you are finished cleaning with
the tools,
be sure to lift cover from
hose tube and reposition hose
end into tube.
Select proper tool
A. Dusting brush may be
used for carved furniture, table tops,
books, lamps, lighting fixtures,
venetian blinds, baseboards, shutters, and registers.
B. Furniture nozzle may be used
for upholstered furniture, draperies,
mattresses, clothing, automobile
interiors, and carpeted stairs.
C. Wand is used to give extra length
to your hose. Use it with any of the
above tools.
D. Crevice wand may be used in
tight spaces, corners and along
edges in such places as dresser
drawers, upholstered furniture, stairs
and baseboards. It can also be
used for extra reach with the dusting
brush and/or extension wand.
Cleaning tools
Tools allow for cleaning surfaces
above the floor and for reaching hard
to clean areas.
Suction will automatically be diverted
to the hose when handle is in upright
position and cleaner is turned ON.
CAUTION: Agitator continues to
rotate while cleaner handle is in
upright position. Avoid tipping
cleaner or setting it on furniture,
fringed area rugs or carpeted stairs
during tool use.
How to clean tools
To clean hose, wipe off dirt with a cloth
dampened in a mild detergent. Rinse
with a damp cloth.
Cleaning tools may be washed in
warm water with a detergent. Rinse
and air dry before using.
6
Stair cleaning
A stair cleaning handle has been
designed for ease in using your
cleaner on stairs. With handle in operating position, place fingers under the
edge of stair cleaning handle and
guide cleaner with the other hand on
upper handle.
As an alternative, you may use the
hose and furniture nozzle for stair
cleaning. Clean from bottom to top.
When using cleaning tools, the agitator will continue to rotate.
CAUTION: To avoid personal injury
or unnecessary wear to carpet, and
to prevent the cleaner from falling,
always place it a t bottom of stairs.
23
24
24
25
25
26
23
A
B
D
C
Attach tool or wand to the
hose (C) by pushing it firmly
into hose.
Attach second wand or tool to wand
(D) by pushing it firmly onto the
wand.
Twist wand or tool slightly to tighten
or loosen the connection.
Disconnect cleaner from electrical
outlet before attempting to service it in any manner.
Do not operate cleaner without
either cloth filter bag or paper filter bag in place.
The cloth filter bag
When to empty
Check filter bag from time to time. It
should be emptied often. If the filter
bag is allowed to overfill, the cleaner
will not operate effectively.
A
B
26
C
D
Maintenance
Reposition bag door by placing
tabs on bottom of door into
opening. Press top of door to snap
securely shut.
Should you want to replace the cloth
filter bag, ask for
part no. 43667-050.
Hold filter bag as shown in
Fig. 28 aligning opening in bag
with (B). Push (A) firmly onto (B). Fit
bottom of filter bag into bag compartment.
After replacing clip, open bag
cap (C).
To replace filter bag clip, first
fold down top of bag over
plastic strip (D).
Push clip over edge.
Empty filter bag over paper,
shaking bag until clean.
Slide filter bag clip from bottom
of bag.
Snap cap (C) into collar opening.
Grasp filter bag collar (A) and
pull collar from tube (B).
How to empty
Push down at top of bag door
and pull forward. Remove door.
7
27
28
29
31
32
34
32
31
29
28
27
A
B
34
A
B
35
35
D
C
33
33
30
30
C
The final filter assists in the fil-
tration process to return clean
air to the room.
To remove this filter when it becomes
dirty, pull out filter as shown.
Hand wash the filter in cold water
with mild detergent.
Let filter air
dry and reposition it on
the side of cleaner.
Reposition bag door.
How to clean
Disconnect cleaner from electrical
outlet.
The secondary filter (A),
located behind the grill in the
bottom of bag compartment, protects the motor from dirt particles.
To clean the filter when it becomes
dirty, remove bag door, pull off grill
and lift out filter.
Hand wash filter in cold water with
mild detergent, then air dry.
Reposition
dry filter and grill.
Should you want to replace this filter,
ask for part no. 38765-022.
8
Optional paper filter
bag
A Type Y disposable paper bag
may be used with the cleaner in
place of the cloth filter bag.
How to install
Disconnect cleaner from electrical
outlet.
1. Remove cloth filter bag from
cleaner following Figs. 27-29.
2. Hold paper filter bag collar as
shown in Fig. 28, aligning opening
in bag with tube (B). Push collar
firmly onto tube.
3. Tuck in filter bag and reposition
bag door as shown in Fig. 35.
When to replace
It is recommended that you change
the paper filter bag when dirt reaches the dotted line. If more dirt than
this accumulates, the cleaner will not
operate effectively.
CAUTION: Very fine materials
such as face powder, cornstarch,
fireplace ashes or fireplace soot,
may seal the filter bag and may
cause it to burst even though it is
only partially full of dirt. When
cleaner is used to remove material
of this nature, change filter bag
often.
Where to buy
Filter bags may be purchased from
a Triple S Authorized Dealer.
When ordering paper filter bags,
be sure to give the model number
of your cleaner.
What to buy
To assure cleaning effectiveness,
use only
Type Y disposable filter
bags.
The secondary &
final filters
36
37
37
36
A
Should you want to replace this filter,
ask for
part no. 43613-006.
Do not operate cleaner without
either the secondary or final filter
in place.
Loading...