SSI America MG1-30-A-9V, MG1-3000-A-9V, MG1-1000-A-9V-R, MG1-100-A-9V, MG1-500-A-9V User Manual
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
Product Description
The MediaGauge™ Model MG1-9V is a NEMA 4X rated stand
alone 9V battery operated multi-functional digital pressure gauge
with a standard input pressure port made of 316L stainless steel
which has better pitting corrosion resistance in some media, such
as seawater. The MediaGauge™ MG1-9V is well suited for
marine applications.
The MediaGauge™ MG1-9V contains a media isolated
piezoresistive pressure sensing element, signal conditioning
circuitry for temperature and calibration compensation, a pressure
port and a LCD back lit display. The MG1-9V has an accuracy of
± 1.0% full scale and is a lower cost alternative in the SSI
MediaGauge™ family of digital pressure gauges.
The MediaGauge™ MG1-9V comes standard with a variety of
keypad operated functions – multiple pressure unit displ ay reading
(PSI, BAR or MPA); memory storage of maximum peak pressure
reading; and zero adjustment.
The MediaGauge™ MG1-9V is made of all laser-welded 316L
stainless steel for optimal media isolation and usage in a wide
variety of media and corrosion or oxidation resistant applications.
These compact 2 ½ inch, robust gauges measure pressures from
5 PSI to 5000 PSI and are well suited for a variety of industrial and
commercial applications such as marine, refrigeration,
compressors, pumps, hydraulics, pneumatics and waste water.
The MediaGauge™ MG1-9V digital pressure gauge has better
accuracy, longer life and standard multiple functions which make it
a better choice than mechanical pressure gauges.
MediaGauge™ Model MG1-9V
Product Features
Accuracy: ± 1.0 % Full Scale
Pressure Ranges: 5, 30, 100, 200, 500, 1000, 3000,
5000 PSI
Keypad Operated Functions: Auto zero and peak hold
Operating Temperature: -10°C to 60°C
Storage Temperature: -20°C to 85°C
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
1
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
Typical Applications: General Purpose, Test, Process
Control, MRO, Water, Compressors, Refrigeration; Fuel
Cells; Pumps; Hydraulics; Spraying Systems;
Pneumatics; Flow; Robotics; Agriculture; Hydrogen
Storage
NIST traceable certificates available
NEMA 4X Rating
Chemical Compatibilities: Any gas or liquid
compatible with 316L stainless steel. For example, Sea
Water, Salt Water, Motor Oil, Diesel, Hydraulic fluid,
Brake Fluid, Water, Waste Water, Hydrogen, Nitrogen,
and Air.
LCD Display Battery Saver Mode: MG1-9V
automatically powers down after 3 minutes.
Multiple Pressure Units: PSI, BAR, MPA (kg/cm²)
Compact, Robust Package: 2 ½ inches with black
ABS Thermoplastic case
Measurement Technology
In general, pressure measurement technology translates a
force from an induced pressure into a n electric al quantity. I n
digital pressure gauges, the electrical quantity is then
translated into pressure units and digitally displayed.
The SSI’s MediaGauge™ MG1-9V digital pressure gauge
includes an 316L stainless steel input pressure port, a
piezoresistive pressure sensing element, signal conditioning
circuitry for temperature and calibration compensation, and
a LCD that displays the pressure measured in either PSI,
BAR or MPA (kg/cm²) units.
The piezoresistive sensing element consists of an oil filled
micro-machined 316L stainless steel convoluted diaphragm
with a silicon crystal sensor. The silicon crystal sensor is
mounted on a 304L stainless steel housing and laser
welded to the diaphragm. Optimal media isolation is
achieved when the media’s pressure acts directly on the
316L stainless steel diaphragm and is then transferred
through the oil to the silicon sensor.
Strain gauges (resistive elements) in the silicon are used in
a Wheatstone Bridge circuit. When pressure is applied, the
resistivity of the strain gauges changes proportional to the
pressure applied. One leg of the bridge measures the input
pressures port. The other leg of the bridge is connected to
the reference port (vacuum pressure 0 PSI) the input
pressure port is compared to.
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
2
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
Since piezo resistive pressure sensors are sensitive to
changes in temperature, the MediaGauge™ MG1-9V uses
signal conditioning to compensate for temperature and
calibration. The output signal is then converted into one of 3
user selectable forms (select units with the ON/UNIT/OFF
button):
1) PSI
2) BAR
3) MPA (kg/cm²)
The MediaGauge™ MG1-9V will display the pressure
reading after the ON/UNIT/OFF button is depressed. The
pressure measurement reading is updated 3 times per
second.
MediaGauge™ MG1-9V Panel
MediaGauge™ MG1-9V panel has a LCD display and t hree multifunctional buttons – ON/UNIT/OFF; LIGHT/P-H (Peak-Held) and
RESET/CLEAR.
ON/UNIT/OFF button is used to display the pressure
The
reading; switch between pressure units (PSI; BAR; and MPA) and
to power down the unit.
To power on the unit: Press the ON/UNIT/OFF button. The
MediaGauge™ MG1-9V has a battery saver mode and will
automatically shut off the display after 3 minutes.
To display the pressure reading in a different pressure unit:
Continue to depress the ON/UNIT/OFF button until the arrow in
the LCD points to the pressure units desired.
To manually power down the unit: Press the ON/UNIT/OFF
button and hold down for 3 seconds until OFF is displayed and
then release the button.
LIGHT/P-H (Peak-Hold) button is used to turn the LCD
The
backlight on/off and to display the maximum peak pressure the
unit has measured.
To turn the LCD backlight on: Press the LIGHT/P-H button once.
To turn the LCD backlight off: Press the LIGHT/P-H button
again.
To see the maximum peak pressure the unit has measured:
Press and hold down the LIGHT/P-H button for 3 seconds. The
maximum pressure reading will be blinking. If the maximum
pressure read was over the unit’s maximum press ure range, o.L
will be blinking on the display.
To return to the current pressure reading: Press the LIGHT/P-H
button and hold down for 3 seconds.
RESET/CLEAR button is used to reset the gauge to
The
whatever pressure is currently applied to the port and to clear the
stored maximum peak pressure reading. Note: The
RESET/CLEAR button only functions when held down for 3
seconds.
To reference your MediaGauge™ digital pressure gauge to the
input port:
seconds. The MediaGauge™ MG1-9V will now be reference to
your input port. For example, if you have 20 psi on the display and
then you press and hold the RESET/CLEAR button for 3 secon ds
the display will show 0.0 psi. A measurement of 30 psi would then
read as 10 psi on the display.
Press and hold the RESET/CLEAR button for 3
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
3
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
To reset the MediaGauge™ digital pressure gauge: Make sur e
the input port is either disconnected or connected to a 0 psi input.
Press and hold down the RESET/CLEAR button for 3 seconds.
To clear the maximum peak pressure reading: Press and hold
down the LIGHT/P-H button for 3 seconds until the maximum
pressure reading appears on the LCD (it will be bli nking). Releas e
the LIGHT/P-H button. Press and hold down RESET/CLEAR
button for 3 seconds.
Installation/Mounting
1) Mount the MediaGauge™ MG1-9V digital pressure gauge
on a suitable (1/4” NPT) female fitting. Use Teflon tape
or pipe dope to seal the threads.
2) Do no over tighten. Torque to 150 in lbs +/- 1 in lb
Electrical Specifications
LCD Resolution (1000,3000,5000 PSI) 1
Proof Pressure 3 X Full Scale
Burst Pressure
Operating Temperature Range -10° to 60°C (14° to 140°F)
Storage Temperature Range -20° to 85°C (-4°to 185°F)
10 X Full Scale or 15,000
PSI whichever is less
Tested Conditions
Humidity 250 Hours (40°C and 90% to 95% R.H.
Pressure/Temperature
Cycles
Thermal Shock
> 1.8 million Cycles (0 to FS @ 8Hz and
-20° to 85°C)
250 Cycles (85 to -20°C. 0.5 hr soaks at
temperature
Supply Voltage 9V Battery
Response Time < 1 ms
Accuracy ± 1.0 FS
LCD Resolution (5 PSI) 0.001
LCD Resolution (30 PSI) 0.01
LCD Resolution (100, 200,500PSI) 0.1
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
Vibration
4
144 Hours (100 to 2000 Hz, 20g
sinusoidal in 3 axes)
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
MediaGauge™ MG1-9V with 22mm Hex and 1/4" - 18 NPT Process Connection
3
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
5
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
SSI Technologies – Application Note PS-AN6
MediaGauge™ (Model MG1-9V) Digital Pressure Gauge
Product Overview
Digital Pressure Gauge Ordering System
The following explains SSI’s MediaGauge™ Digital Pressure Gauge order number sequence.
Example
MG1 - 500 - A - 9V
Product Family
• MG1
Rubber Boot Options:
Order P/N 24610.1 for Model MG1
Pressure Ranges
• 5
• 30
• 100
• 200
• 500
• 1000
• 3000
• 5000
Port Configuration
Hex
Port
• A 22mm 1/4 - 18 NPT
Connector
• 9V Battery, Operated
3
SSI TECHNOLOGIES, INC.
Controls Division
2643 West Court Street
Janesville, WI 53548-5011
Phone: (608)758-1500
Fax: (608)758-2491
6
Copyright November 6, 2008
SSI Technologies Inc.
All Rights Reserved
Revision 3
Loading...