( 1 / 8)
Instruction Manual
Models:
version 1.0 since 21 July 2017
ATTENTION!
This instruction manual contains important information about the installation and the use of
the equipment. Please read and follow these instructions carefully.
Always ensure that the power to the equipment is disconnected before opening the
equipment or commencing any maintenance work.
DP6_en_manual_M056.doc
Single Channel 6kW
Studio Dimmer
DP6
( 2 / 8)
Dimmer DP5 is designed to fulfill all the requirements of most lighting applications – mainly
in TV or special scenarios when the single channel dimming by various controlling ways it’s
necessary. It’s equipped with 400us Risetime choke which guarantee very low lamp noise.
The other benefit of DP6 is option to use W-DMX inside which allows control device without
DMX cable. Additionally DMX OUT connector will be as source of DMX signal for any other
DMX equipment or color changer.
• Convectional cooled without fan
• WDMX / DMX / Fader control
• Power output: 1 x 26 A / 6000W
• Main breaker: D32A
• STUDIO Risetime 400uS
• DMX address selector
• LTP function fader/DMX
• DMX input with THRU output
• W-DMX with DMX output function
• Phase–angle control SSR
• Double Overheat protection
• Variable input/output connectors
DMX/W-DMX input with THRU output
USITT DMX 512
Power supply
AC230V / 40-65Hz, CEE32A/3p, single phase
Dimensions
Aluminium: 270x220x360mm 9.7kg
Min./Max. load
100W / 6000W
Device use:
( 3 / 8)
Connect power power input and output load to the DP5. Via fader you can select the
output value. This value is in LTP law with DMX input. For avoid changes via DMX please
setup DIP switch #10 to the position of disabling DMX.
LTP: Latest takes precedence: change of signal take controlling of output power.
Front panel description
1. DMX in / DMX OUT connector
Pin 1 GND
Pin 2 Data Pin 3 Data +
Pin 4,5 Not connected
2. DMX start address and MODE selector switch
a. DMX address : 0-9 switches : active on TOP
b. MODE switch : 10 switch :
i. DMX & ANALOG – dip switch in position 1 – TOP
ii. ANALOG only – DIP switch in position 0 – BOTTOM
In analog only mode the DMX OUT connector isn’t connected to DMX IN connector!!!
3. ANALOG fader knob
i. 0-100% of output value
4. POWER LED
i. Solid GREEN – all OK
ii. Blinking GREEN – over temperature
5. DMX OK LED
i. Solid GREEN – DMX signal OK
ii. Off – DMX signal not presence
6. DMX ERR LED
i. Solid RED – DMX signal ERR – check cable for 2/3 inv. connection
ii. Off – DMX signal not presence
( 4 / 8)
Rear panel description
On rear panel are placed CEE32A/3p in/out connectors, fuse for protection of electronic
and OUTPUT indication.
( 5 / 8)
IMPORTANT INSTRUCTIONS:
All safety and operating instructions should be read before the equipment is installed or
operated.
IMPORTANT SAFETY INFORMATIONS:
The following general safety precautions have to be observed during all phases of
operation, service, and repair of this equipment. Failure to comply with these precautions
or with specific warning in this manual violates safety standards of design, manufacture,
and intended use of this equipment. Do not operate this equipment in the presence of
flammable gases or fumes. Operation of any electrical instrument in such an environment
constitutes a definite safety hazard. Do not operate this equipment near water or in areas
with wet floors, also not in high humidity atmosphere where condensation forms on the
equipment. It should never be placed near or over heat register or other source of heated
air and it should not be installed or operated without proper ventilation. Device must be
connected to the secured circuit with circuit breaker or main switch 16A maximum. Device
doesn’t contain any fuse, no serviceable parts inside.
Warranty:
The product design should be varied to keep the product continuously updated. These
prices should be subject to possible variations for eventual rises of production costs or
duties. Claims for possible damages during the freight, must be notified to the carrier. Any
claim must be notified within 8 days from receive of the goods. The buyer is responsible
of the right installation and use of the apparatus.
The apparatus is guaranteed for TWO YEARS from date of purchase against defects of
manufacture or materials. Defects and breakages caused by wrong connection or use of
the apparatuses are not subject to guarantee. For any dispute is competent the Tribunal
of Bratislava.
( 6 / 8)
DECLARATION OF CONFORMITY
Name of producer: SRS Group s.r.o.
Address of producer: Rybnicna 36/D, SK- 83106 Bratislava, Slovak Republic
Declares that the product
Name of product: Single channel dimming unit
Type: DP6, DP6W
Corresponds to the following product specifications:
EN60065, resp. EN60950-1
EN55103-1:2009
55103-2:2009
EN55014
EN55011
Additional information:
All DMX512 and analogue inputs and outputs must be shielded and the shielding must be
connected to the ground respective to the case of the corresponding plug. The unit and all
connected apparatuses must also be earthed via main cable. Always check for correct
shielding of the device.
Bratislava, 10 May 2009 Robert Sloboda
( 7 / 8)
( 8 / 8)
Copyright 2017 SRS Group, s.r.o. | Specifications subject to change without notice.
Document: DP6_en_manual_M056.doc | Version 1.0 | Actual as of: 21 July 2017
SRS Group s.r.o.
Rybnicna 36/D | 831 07 Bratislava | Slovakia
Phone: +421 2 44 681 417 | Fax: +421 2 4468 1419
Email: sales@srs-group.com | www.srs-group.com
Loading...