SRS Labs SR530 User Manual

Download

MODEL SR530

LOCK-IN AMPLIFIER

1290-D Reamwood Avenue

Sunnyvale, CA 94089 U.S.A.

Phone: (408) 744-9040 • Fax: (408) 744-9049

Email: info@thinkSRS.com • www.thinkSRS.com

Stanford Research Systems, Inc.

Rev. 2.3 (06/2005)

Table of Contents

Condensed Information

SAFETY and Preparation for use 1

Symbols 2 Specifications 3 Front Panel Summary 5 Abridged Command List 7 Status Byte Definition 8 Configuration Switches 8

Guide to Operation

Front Panel 9

Signal Inputs 9 Signal Fi lters 9 Sensitivity 9 Dynamic Reserve 10 Status Indicators 10 Display Select 10 Channel 1 Display 10 R Output 11 Output Channel 1 11 Rel Channel 1 11 Offset Channel 1 11 Expand Channel 1 12 X (RCOSØ) Output 12 Channel 2 Display 12 Ø Output 12 Output Channel 2 13 Rel Channel 2 13 Auto Phase 13 Offset Channel 2 13 Expand Channel 2 14 Y (RSINØ) Output 14 Reference Input 14 Trigger Level 14 Reference Mode 15 Reference Display 15 Phase Controls 15 Time Constants 15 Noise Measurements 15 Power Switch 16 Local/Remote Operation 16 Default Settings 16

Rear Panel 17 AC Power 17 GPIB (IEEE-488) Connector 17 RS232 Connector 17 Signal Monitor Output 17 Pre-Amp Connector 17 A/D Inputs and D/A Outputs 17 Ratio Feature 17 Internal Oscillator 17

Guide to Programming

Communications 19 Command Syntax 19 Status LED's 19 RS232 Echo Feature 20 Try-out with an ASCII Terminal 20

Command List 21 Status Byte 24 Errors 24 Reset Command 25 Trouble-Shooting Interf ac e Probl ems 25 Common Hardware Problems 25 Common Software Problems 25

RS232 Interface

Introduction to the RS232 26 Data Communications Equipment 26 Wait Command 26 Termination Sequence 26

GPIB (IEEE-488) Interface

Introduction to the GPIB 26 GPIB Capabilities 26 Response to Special GPIB comman ds 26 Serial Polls and SRQ's 27 Echo Mode using the RS232 27 Using Both the RS232 & GPIB 27

Lock-in Technique

Introduction to Lock-in Amplifier s 28 Measurement Example 28 Understanding the Specifications 29 Shielding and Ground Loops 29 Dynamic Reserve 30 Current Inputs 30 Bandpass Filter 30 Notch Filters 31 Frequency Range 31 Output Time Constants 31 Noise Measurements 31 Ratio Capability 31 Computer Interfaces 31 Internal Oscillator 31

SR530 Block Diagram

Block Diagram 32 Signal Channel 33 Reference Channel 33 Phase-Sensitive Detector 33 DC Amplifier and System Gain 33 Microprocessor System 33

Circuit Description

Introduction 34 Signal Amplifier 34 Current Amplifier 34 Notch Filters 34 Bandpass Filter 34 Reference Oscillator 35 PSD, LP Filters and DC Amplifier 35 Analog Output 36 A/D's 36 D/A's 36 Expand 36 Front Panel 36 Microprocessor Control 36 RS232 Interface 37 GPIB Interface 37 Power Supplies 37 Internal Oscillator 37

Calibration and Repair

Introduction 38 Multiplier Adjustments 38 Amplifier and Filter Adjustments 38 CMRR Adjustment 38 Line Notch Filter Adjustment 39 2xLine Notch Filter Adjustment 39 Repairing Damaged Front-End 39

IBM PC, Microsoft Basic, via GPIB 51 HP-85, HP Basic, via HPIB 53

Documentation

Parts List, Oscillator Board 55 Parts List, Main Board 56 Parts List, Front Panel Board 70 Parts List, Quad Board 73 Parts List, Miscellaneous 77 Schematic Diagrams 79

Appendix A: Noise Sources and Cures

Johnson Noise 40 '1/f' Noise 40 Noise Spectrum 40 Capacitive Coupling 41 Inductive Coupling 41 Ground Loops 42 Microphonics 42 Thermocouple Effect 42

Appendix B: RS232

Simplest Case Using the RS232 43 Using Control Lines 43 Baud Rates 43 Stop Bits 44 Parity 44 Voltage Levels 44 'Eavesdropping' 44

Appendix C: GPIB

Introduction to the GPIB 45 Bus Description 45

Appendix D: Program Examples

Program Description 46 IBM PC, Microsoft Basic, via RS232 46 IBM PC, Microsoft Fortran, via RS232 47 IBM PC, Microsoft C, via RS232 49

Safety and Preparation for Use

***CAUTION***: This instrument may be damaged if operated with the LINE VOLTAGE SELECTOR set for the wrong applied ac input-source voltage or if the wrong fuse is installed.

LINE VOLTAGE SELECTION

The SR530 operates from a 100V, 120V, 220V, or 240V nominal ac power source having a line frequency of 50 or 60 Hz. Before connecting the power cord to a power source, verify that the LINE VOLTAGE SELECTOR card, located in the rear panel fuse holder, is set so that the correct ac input voltage value is visible.

Conversion to other ac input voltages requires a change in the fuse holder voltage card position and fuse value. Disconnect the power cord, open the fuse holder cover door and rotate the fuse-pull lever to remove the fuse. Remove the small printed circuit board and select the operating voltage by orienting the printed circuit board to position the desired voltage to be visible when pushed firmly into its slot. Rotate the fuse-pull lever back into its normal position and insert the correct fuse into the fuse holder.

LINE FUSE

Verify that the correct line fuse is installed before connecting the line cord. For 100V and 120V, use a ½ Amp fuse and for 220V and 240V, use a 1/4 Amp fuse.

FURNISHED ACCESSORIES

- Power Cord

- Operating Manual

ENVIRONMENTAL CONDITIONS

OPERATING Temperature: +10° C to +40° C (Specifications apply over +18° C to +28° C) Relative Humidity: < 90% Non-condensing

NON-OPERATING Temperature: -25° C to 65° C Humidity: < 95% Non-condensig

OPERATE WITH COVERS IN PLACE

To avoid personal injury, do not remove the product covers or panels. Do not operate the product without all covers and panels in place.

WARNING REGARDING USE WITH PHOTOMULTIPLIERS

LINE CORD

This instrument has a detachable, three-wire power cord with a three-contact plug for connection to both the power source and protective ground. The protective ground contact connects to the accessible metal parts of the instrument. To prevent electrical shock, always use a power source outlet that has a properly grounded protectiv e-gr ou nd con tac t.

It is relatively easy to damage the signal inputs if a photomultiplier is used improperly with the lock-in amplifier. When left completely unterminated, a PMT will charge a cable to a few hundred volts in a very short time. If this cable is connected to the lockin, the stored charge may damage the front-end transistors. To avoid this problem, provide a leakage path of about 100 KΩ to ground inside the base of the PMT to prevent charge accumulation.

SR530 Specification Summary

General

Power 100, 120, 220, 240 VAC (50/60 Hz); 35 Watts Max Mechanical 17" x 17" x 5.25" (Rack Mount Included) 16 lbs. Warranty Two years parts and labor.

Signal Channel

Inputs Voltage: Single-ended or True Differential

Current: 10

Impedance Voltage: 100 MΩ + 25 pF, ac coupled

Current: 1 kΩ to virtual ground

Full Scale Sensitivity Voltage: 100 nV (10 nV on expand) to 500 mV

Current: 100 fA to 0.5 µA

Maximum Inputs Voltage: 100 VDC, 10 VAC damage threshold

Current: 10 mA damage threshold

Noise Voltage: 7 nV/√Hz at 1 kHz

Current: 0.13 pA/√ Hz at 1 kHz

Common Mode Range: 1 Volt peak; Rejection: 100 dB dc to 1KHz

Gain Accuracy 1% (2 Hz to 100KHz) Gain Stability 200 ppm/°C Signal Filters 60 Hz notch, -50 dB (Q=10, adjustable from 45 to 65 Hz)

120 Hz notch, -50 dB (Q=10, adjustable from 100 to 130 Hz)) Tracking bandpass set to within 1% of ref freq (Q=5)

Dynamic Reserve 20 dB LOW (1 µV to 500 mV sensitivity)

40 dB NORM (100 nV to 50 mV sensitivity) 60 dB HIGH (100 nV to 5 mV sensitivity) Bandpass filter adds 20 dB to dynamic reserve Line Notch filters increase dynamic reserve to 100 dB

Volts/Amp

2 VAC peak-to-peak saturation

1 µA ac peak-to-peak saturation

Above 1KHz the CMRR degrades by 6 dB/Octave

Reference Channel

Frequency 0.5 Hz to 100 kHz Input Impedance 1 MΩ, ac coupled Trigger SINE: 100 mV minimum, 1Vrms nominal

PULSE: ±1 Volt, 1 µsec minimum width

Mode Fundamental (f) or 2nd Harmonic (2f)

Acquisition Time 25 Sec at 1 Hz

6 Sec at 10 Hz

2 Sec at 10 kHz Slew Rate 1 decade per 10 S at 1 kHz Phase Control 90° shifts

Fine shifts in 0.025° steps Phase Noise 0.01° rms at 1 kHz, 100 msec, 12 dB TC Phase Drift 0.1°/°C Phase Error Less than 1° above 10Hz Orthogonality 90° ± 1°

Demodulator

Stability 5 ppm/°C on LOW dy nam ic res erv e

50 ppm/°C on NORM dynamic reserve

500 ppm/°C on HIGH dynamic reserve Time Constants Pre: 1msec to 100 sec (6 dB/Octave)

Post: 1sec, 0.1 sec, none (6 dB/Octave) or none Offset Up to 1X full scale (10X on expand)

Both channels may be offset Harmonic Rej -55 dB (bandpass filter in)

Outputs & Interfaces

Channel 1 Outputs X (RcosØ), X Offset, R (magnitude), R Offset, X Noise, X5 (external D/A) Channel 2 Outputs Y (RsinØ), Y Offset, Ø (phase shift of signal), Y Noise, X6 (external D/A) Output Meters 2% Precision mirrored analo g meter

Output LCD's Four digit auto-ranging LCD display shows same values as the analog meters

Output BNC's ±10 V output corresponds to full scale input, <1Ω output impedance X Output X (RcosØ), ±10 V full scale, < 1Ω output impedance Y Output Y (RsinØ), ±10 V full scale, < 1Ω output imp eda nce Reference LCD Four digit LCD display for reference phase shift or frequency RS232 Interface controls all functions. Baud rates from 300 to 19.2 K GPIB Interface controls all functions. ( IEEE-488 Std ) A/D 4 BNC inputs with 13 bit resolution (±10.24 V) D/A 2 BNC outputs with 13 bit resolution (±10.24 V) Ratio Ratio output equals 10X Channel 1 output divided by the Denominator input. Internal Oscillator Range: 1 Hz to 100 kHz, 1% accuracy

Stability: 150 ppm/°C Distortion: 2% THD Amplitude: 1% accuracy, 500 ppm/°C stability

Front Panel Summary

Signal Inputs Single Ended (A), True Differential (A-B), or Current (I)

Signal Filters Bandpass: Q-of-5 Auto-tracking filter (In or Out)

Line Notch: Q-of-10 Notch Filter at line frequency (In or Out) 2XLine Notch: Q-of-10 Notch Filter at twice line frequency (In or Out)

Sensitivity Full scale sensitivity from 100 nV to 500 mV RMS for voltage inputs

or from 100 fA to 500 nA RMS for current inputs.

Dynamic Reserve Select Dynamic Reserve

LOW 20 dB 5 ppm 1 µV to 500 mV NORM 40 dB 50 ppm 100 nV to 50 mV HIGH 60 dB 500 ppm 100 nV to 5 mV

Status Indicators OVLD Signal Overload

UNLK PLL is not locked to the reference input ERR Illegal or Unrecognized command ACT RS232 or GPIB interface Activity REM Remote mode: front panel has been locked-out

Display Select Channel 1 Channel 2

X (RcosØ) Y (RsinØ) X Offset Y Offset R (Magnitude) Ø (Phase) R Offset Ø (no offset) X Noise Y Noise

X5 (D/A) X6 (D/A) Analog Meters Displays Channel 1 and 2 Outputs as a fraction of full scale Output LCD's Displays the Channel 1 and 2 Outputs in absolute units Output BNC's Channel 1 and 2 Outputs follow Analog Meters, ± 10 V for ± full scale Expand Multiplies the Channel 1 or 2 Analog Meter and Output voltage by a factor X1 or X10.

Stability Sensitivity Ranges

REL Set the Channel 1 or 2 Offset to null the output: subsequent readings are relative

readings. REL with phase display performs auto-phasing. REL with X5, X6 display

zeroes the D/A outputs. Offset Enables or Disables Offset, and allows any offset (up to full scale) to be entered. X, Y,

and R may be offset and X5, X6 may be adjusted. Phase is offset using the reference

phase shift. X BNC X (RcosØ) output, ± 10V full scale Y BNC Y (RsinØ) output, ± 10V full scale Reference Input 1 MΩ Input, 0.5 Hz to 100 KHz, 100 mV minimum Reference Trigger Trigger on rising edge, zero crossing, or falling edge f/2f Mode PLL can lock to either X1 or X2 of the reference input frequency

Phase Controls Adjust phase in smoothly accelerating 0.025° steps, or by

90° steps. Press both 90° buttons to zero the phase. Reference LCD Display reference phase setting or reference frequency Time Constants Pre-filter has time constants from 1 mS to 100 S (6 dB/Octave)

Post-filter has time constants of 0, 0.1 or 1.0 S (6 dB/Octave) ENBW Equivalent Noise Bandwidth. Specifies the bandwidth when making

Noise measurements. (1Hz or 10 Hz ENBW) Power Switch Instrument settings from the last use are recalled on power-up

Abridged Command List

AX Auto offset X AY Auto offset Y AR Auto offset R AP Auto phase

B Return Bandpass Filter Sta tus B0 Take out the Bandpass Filter B1 Put in the Bandpass Filter

C Return the Reference LCD Status C0 Display the Reference Frequency C1 Displ ay the Refere nce Phas e Sh ift

D Return Dynamic Reserve Setting D0 Set DR to LOW range D1 Set DR to NORM range D2 Set DR to HIGH range

En Return Channel n (1 or 2) Expand

Status En,0 Turn Channel n Expand off En,1 Turn Channel n Expand on

F Return the Reference Frequency G Return the Sensitivity Setting

G1 Select 10 nV Full-Scale ... (G1-G3 with SRS preamp only) G24 Select 500 mV Full-Scale

H Return Preamp Status (1=installed) I Return the Remote/Local Status

I0 Select Local: Front panel active I1 Select Remote: Front panel inactive I2 Select Remote with full lock-out

J Set RS232 End-of-Record to <cr> Jn,m,o,p Set End-of-record to n,m,o,p

K1 Simulates Key-press of button #1 ... (see un-abridged command list) K32 Simulates Key-press of button #32

L1 Return Status of Line Notch Filter L1,0 Remove Line Notch Filter L1,1 Insert Line Notch Filter

L2 Return Status of 2XLine Filter L2,0 Remove 2XLine Notch Filter L2,1 Insert 2XLine Notch Filter

M Return the f/2f Status M0 Set reference mode to f M1 Set reference mode to 2f

N Return the ENBW setting N0 Select 1 Hz ENBW N1 Select 10 Hz ENBW

OX Return X Offset Status OX 0 Turn off X Offset OX 1,v Turn on X Offset, v = offset OY Return Y Offset Status OY 0 Turn off Y Offset OY 1,v Turn on Y Offset, v = offset OR Return R Offset Status OR 0 Turn off R Offset OR 1,v Turn on R Offset, v = offset

P Return the Phase Setting Pv Set the Phase to v. Abs(v) <999 deg

Q1 Return the Channel 1 output Q2 Return the Channel 2 output QX Return the X Output QY Return the Y Output

R Return the trigger mode R0 Set the trigger for rising edge R1 Set the trigger for + zero crossing R2 Set the trigger for falling edge

S Return the display status S0 Display X and Y S1 Display X and Y Offsets S2 Display R and Ø S3 Display R Offset and Ø S4 Display X and Y noise S5 Display X5 and X6 (ext D/A)

T1 Return pre-fi lter sett in g T1,1 Set the pre-filter TC to 1 mS ... T1,11 Set the pre-filter TC to 100 S

T2 Return the post-filter setting T2,0 Remove post filter T2,1 Set the post filter TC to 0.1 S T2,2 Set the post filter TC to 1.0 S

V Return the value of the SRQ mask Vn Set the SRQ Mask to the value n

(See the Status Byte definition)

W Return the RS232 wait interval Wn Set RS232 wait interval to nX4mS

Xn Return the voltage at the rear panel

analog port n. (n from 1 to 6)

X5,v Set analog port 5 to voltage v X6,v Set analog port 6 to voltage v

Y Return the Status Byte value Yn Test bit n of the Status Byte

Z Reset to default settings and cancel

all pending commands.

Status Byte Definition

Bit Meaning

0 Magnitude too small to calculate phase 1 Command Parameter is out-of-range 2 No detectable reference input 3 PLL is not locked to the reference 4 Signal Overload 5 Auto-offset failed: signal too large 6 SRQ generated 7 Unrecognized or illegal command

Configuration Switches

There are two banks of 8 switches, SW1 and SW2, located on the rear panel. SW1 sets the GPIB address and SW2 sets the RS232 parameters. The configuration switches are read continuously and any changes will be effective immediately.

SW1:GPIB Mode Switches

Bit Example Function

1 } up GPIB Address Switches 2 } up Address 0 to 30 allowed 3 } up 'up' for bit = 1 4 } down 'down' for bit = 0 5 } up (Most Significant Bit)

6 down 'down' to echo on RS232 (normally 'up')

7 up Not Used 8 up Not Used

If the GPIB mode switches are set as shown in the example column above, then the lockin will be addressed as GPIB device #23, and all GPIB commands and data will be echoed over the RS232 for de-bugging purposes.

SW2:RS232 Mode Switches

Bit 1 Bit 2 Bit 3 Baud Rate

up up up 19200 down up up 9600 up down up 4800 down down up 2400 up up down 1200 down up down 600 up down down 300

Bit Setting Explanation

4 up Odd parity down Even parity

5 up No parity down Parity enabled

6 up No echo (for computer) down Echo mode (for terminal)

7 up Two stop bits down One stop bit

8 unused

Eight data bits are always sent, regardless of the parity setting. The most significant bit is always zero.

Example: Bit 1 'down' and all others 'up' for RS232 communication at 9600 baud, no parity, two stop bits, and no echo or prompts by the SR530.

SR510 Guide to Operation Front Panel

The front panel has been designed to be almost self-explanatory. The effect of each keypress is usually reflected in the change of a nearby LED indicator or by a change in the quantity shown on a digital display. This discussion explains each section of the front panel, proceeding left to right.

Signal Inputs

There are three input connectors located in the SIGNAL INPUT section of the front panel. The rocker switch located above the B input selects the input mode, either single-ended, A, differential, A-B, or current, I.

The A and B inputs are voltage inputs with 100 MΩ, 25 pF input impedance. Their connector shields are isolated from the chassis ground by 10Ω. These inputs are protected to 100V dc but the ac input should never exceed 10V peak. The maximum ac input before overload is 1V peak.

The I input is a current input with an input impedance of 1 KΩ to a virtual ground. The largest allowable dc current before overload is 1 µA. No current larger than 10 mA should ever be

applied to this input. The conversion ratio is 10 V/A, thus, the full scale current sensitivities range from 100 fA to 500 nA with a max ac input before overload of 1 µA peak. You should use short cables when using the current input.

allowable signals at the inputs. The notch frequencies are set at the factory to either 50 Hz or 60 Hz. The user can adjust these frequencies. (See the Maintenance and Repair section for alignment details.) These filters precede the bandpass filter in the signal amplifier.

The bandpass filter has a Q of 5 and a 6 dB roll off in either direction. Thus, the pass band (between 70% pass points) is always equal to 1/5th of the center frequency. The center frequency is continually adjusted to be equal to the internal demodulator frequency. When the reference mode is f, the filter tracks the reference. When the mode is 2f, the filter frequency is twice the reference input frequency. The center frequency tracks as fast as the reference oscillator can slew and may be used during frequency scans. The bandpass filter adds up to 20 dB of dynamic reserve for noise signals outside the pass band, and increases the harmonic rejection by at least 13dB. (2nd harmonic attenuated by 13 dB, higher harmonics attenuated 6dB/octave more.) If not needed to improve the dynamic reserve or the harmonic rejection then the filter should be left

OUT.

Sensitivity

The sensitivity is displayed as a value (1-500) and a scale (nV, µV, mV). When using the current

input, which has a gain of 106 V/A, these scales read fA, pA, and nA. The two keys in the SENSITIVITY section move the sensitivity up and down. If either key is held down, the sensitivity will continue to change in the desired direction four times a second.

Signal Filters

There are three user selectable signal filters available; a line frequency notch, a 2X line frequency notch, and an auto-tracking band pas s . Each of the filters has a pair of indicator LED's and a function key located in the SIGNAL FILTERS section of the front panel. Pressing a key will toggle the status of the appropriate filter. The status of each filter is displayed as IN, filter active, or OUT, filter inactive.

The notch filters have a Q of 10 and a depth of at least 50 dB. Thus, the line frequency notch is 6 Hz wide and the 2X line notch has a width of 12 Hz. Both of these filters can increase the dynamic reserve up to 50 dB at the notch frequencies. The achievable reserve is limited by the maximum

The full scale sensitivity can range from 100 nV to 500 mV. The sensitivity indication is not changed by the EXPAND function. The EXPAND function increases the output sensitivity (Volts out /volts in) as well as the resolution of the digital output display.

Not all dynamic reserves are available at all sensitivities. If the sensitivity is changed to a setting for which the dynamic reserve is not allowed, the dynamic reserve will change to the next setting which is allowed. Sensitivity takes precedence over the dynamic reserve. The sensitivity range of each dynamic reserve is shown below.

Dynamic Reserve Sensitivity Range LOW 1 µV through 500 mV

NORM 100 nV through 50 mV HIGH 100 nV through 5 mV

Dynamic Reserve

The dynamic reserve (DR) is set using the keys in the DYNAMIC RESERVE section. The reserve is displayed by the three indicator LED's, HIGH, NORM, LOW. Only those dynamic reserve settings available for the sensitivity are allowed (see above table). For example, when the sensitivity is 500 mV, the DR will always be LOW.

The dynamic reserve and output stability of each setting are shown below.

the output, i.e. in the ac amplifier or output time constant. In this case, the dynamic reserve, sensitivity, time constant, or ENBW needs to be adjusted.

UNLK indicates that the reference oscillator is not phase locked to the external reference input. This can occur if the reference amplitude is too low, the frequency is out of range, or the trigger mode is incorrect for the reference signal waveform.

ERR flashes when an error occurs on one of the computer interfaces, such as an incorrect command, invalid parameter, etc.

ACT indicates activity on the computer interfaces. This LED blinks every time a character is received or transmitted by the SR530.

Setting Dynamic Reserve (ppm/°C) LOW 20 dB 5 NORM 40 dB 50 HIGH 60 dB 500

Since a higher DR results in degraded output stability, you should use the lowest DR setting for which there is no overload indication. Note that using the Bandpass Filter provides about 20dB of additional DR and so allows you to operate with a lower DR setting.

Output Stability

Status

There are five STATUS LED's. OVLD indicates a signal overload. This condition

can occur when the signal is too large, the sensitivity is too high, the dynamic reserve is too low, the offset is on, the expand is on, the time constant is not large enough, or the ENBW is too large.

The OVLD LED blinks four times a second when an output is overloaded. This occurs if an output exceeds full scale. For example, during a quadrature measurement where X exceeds full scale while Y is near zero, a blinking OVLD indicates that it is safe to take data from the Y output since only the X output is overloaded. The signal path to the Y output is not overloaded. OVLD also blinks if a noise measurement is attempted on an output which exceeds full scale.

If the OVLD LED is on continuously or flashes randomly, then an overload has occurred before

REM indicates that the unit is in the remote state and that the front panel controls are not operat ive. There are two remote states. The Remote-WithLockout will not allow any inputs from the front panel. The Remote-Without-Lockout command allows you to return the front panel to operation by pressing the LOCAL key.

Display Select

The keys in the DISPLAY section sele ct the parameters to be displayed on the OUTPUT METERS and the output of the two OUTPUT BNC connectors. The displayed parameters are indicated by one of the six DISPLAY LED's and can be either the two demodulator outputs (X Y), the demodulator output offsets (X OFST Y OFST), the magnitude and phase (R Ø), the magnitude offset and phase (R OFST Ø), the rms noise on X and Y (X NOISE Y NOISE), or the D/A outputs (X5 D/A X6). When displaying NOISE, the equivalent noise bandwidth is selected in the TIME CONSTANT section. When displaying D/A, the 2 outputs are the X5 and X6 rear panel D/A outputs, allowing the D/A outputs to be set from the front panel. This feature can be used to set the reference frequency when using the internal oscillator.

Channel 1 Display

The channel 1 outputs are summarized below. X is equal to RcosØ where Ø is the phase shift of the signal relative to the reference oscillator of the lock-in.

display CH1 X

output expand? offset? (RCOSØ)

setting

X X+X XOFST X R R+R R OFST R XNOISE X noise yes yes X+X X5 X5 no adjust X+X

The EXPAND and OFFSET conditions for each display are retained when the DISPLAY is changed. Thus, when the DISPLAY is changed from X to R, the EXPAND and OFFSET assume the conditions set the last time the DISPLAY was

R. If the DISPLAY is changed back to X, the EXPAND and OFFSET return to conditions set for X.

yes yes X+X

ofst

yes yes X

ofst

yes yes X+X

ofst

yes yes X+X

ofst

ofst ofst

ofst

(enbw)

R Output

The magnitude, R, is given by the equation:

R = {(X+X

Note that the X and Y offsets affect the value of R while the X and Y expands do not.

The magnitude output has a resolution of 12 bits plus sign and is updated every 3.5 mS. To achieve maximum accuracy, the magnitude should be as large a fraction of full scale as possible.

R is expanded after the calculation. Thus, when R is expanded, the full scale resolution drops by a factor of 10 to about 9 bits.

)2 + (Y+Y

ofst

)2}

1/2

+ R

ofst

The left hand analog meter always displays the CHANNEL 1 OUTPUT voltage. Accuracy is 2% of full scale.

The CHANNEL 1 LCD display provides a read-out of the displayed parameter in real units. The scale of the displayed quantity is indicated by the three scale LED's to the left of the display. This readout auto ranges and will reflect the sensitivity added when the EXPAND function is on. When displaying X5, the scale LED's are off and the units are volts.

Rel Channel 1

Every time the REL key is pressed, the displayed parameter is offset to zero. This is done by loading the displayed parameter's offset with minus one times the present output. If the output is greater than 1.024 times full scale, the REL function will not be able to zero the output. In this case, the OFFSET ON LED will blink and the offset value will be set to its maximum value.

The REL function and the manual OFFSET are both ways to enter the offset value. After using the REL key, the offset may be adjusted using the manual OFFSET.

When the DISPLAY is X, X OFST, or X NOISE, the REL key sets the X OFFSET (which affects the X (RCOSØ) output). If X NOISE is being displayed, the REL function zeroes X and the noise output will require a few seconds to settle again.

When the DISPLAY is R or R OFST, the REL key sets the R OFFSET.

Output Channel 1

The CHANNEL 1 output is available at the left hand OUTPUT BNC connector. The output parameter is selected by the DISPLAY setting and can be X, X OFST, R (magnitude), R OFST, X NOISE, or X5 (external D/A). (Note that X5 is the ratio output at power up. When displaying X5, the ratio output is 10R/X1). All outputs are ±10V full scale when the EXPAND is off. With the EXPAND on, the output is multipled by 10 effectively increasing the full scale sensitivity by 10. (X5 may not be expanded). The output impedance is < 1Ω and the output current is limited to 20 mA.

The REL key zeroes the X5 output when the

DISPLAY is D/A.

Offset Channel 1

The OFFSET buttons control the manual offset. The offset is turned ON and OFF using the upper key in the OFFSET section. When the offset is ON, the lower two keys are used to set the amount of offset. A single key press will advance the offset by 0.025% of full scale. If the key is held down, the offset advances in larger and larger increments, the largest increment being 10% of full scale. When the offset is turned OFF the applied offset returns to zero but the offset value is not lost. The next press of the upper offset key (return

to ON) sets the offset to the previously entered value.

If an attempt is made to advance the offset value beyond full scale, the ON LED will blink. An offset up to 1.024 times the full scale sensitivity may be entered. When the EXPAND is on, this is 10X the full scale output.

Note that the offsets (either manual offset or those generated by the REL function) represent a fraction of the full scale reading, and so their absolute value will change when the sensitivity scale is changed. A signal which has been nulled by an offset will not be nulled when the sensitivity scale is changed. The analog meter and the output BNC indicate the same value given by the equation:

= 10Ae(AvVicosØ+Vos) {if the output is X}

out

in magnitude to the selected sensitivity which is in phase with the reference oscillator will generate a 10V output. The output impedance is <1Ω and the output current is limited to 20 mA.

The X (RCOSØ) output is affected by the X offset but may not be expanded. The X (RCOSØ) is not affected by the DISPLAY setting except for two cases. When the DISPLAY is set to X OFST, the

X (RCOSØ) output is the X offset. When the DISPLAY is set to X NOISE, the X (RCOSØ)

output has a bandwidth equal to the ENBW (1 or 10 Hz) instead of the time constant.

Channel 2 Display

The channel 2 outputs are summarized below. Y is equal to RsinØ where Ø is the phase shift of the signal relative to the reference oscillator of the lock-in.

where... Ae= 1 or 10 per the Expand

Av= 1/Sensitivity Vi= magnitude of the signal Ø = phase between signal & reference

Vos= offset (fraction of FS < 1.024)

When the DISPLAY is X, X OFST, or X NOISE, the OFFSET keys adjust the X OFFSET (which affects the X (RCOSØ) output). When the DISPLAY is R or R OFST, the OFFSET keys adjust the R OFFSET. When the DISPLAY is X5, the OFFSET up and down keys set the output voltage of D/A output X5 (also on the rear panel) up to ±10.24 V. Adjusting X5 will cancel the

RATIO output.

Expand Channel 1

The output EXPAND is toggled by pressing the key in the Channel 1 EXPAND section. The expand status is indicated by the X10, expand on, and the X1, expand off, LED's. Only the Channel 1 OUTPUT is affected, the X (RCOSØ) output is not expanded.

display CH2 Y setting output

YY+Y YOFST Y Ø Phase no no Y+Y Ø Phase no no Y+Y YNOISE Y noise yes yes Y+Y X6 X6 no adjust Y+Y

The EXPAND and OFFSET conditions for each display are retained when the DISPLAY is changed. Thus, when the DISPLAY is changed from Y to Ø, the EXPAND and OFFSET turn off. If the DISPLAY is changed back to Y the EXPAND and OFFSET return to conditions set for Y.

expand? offset? (RSINØ)

ofst

yes yes Y+Y yes yes Y

ofst

ofst ofst ofst ofst

(enbw)

Ø Output

The phase, Ø, is given by the equation:

Ø = - tan-1 {(Y+Y

Note that the X and Y offsets affect the value of Ø while the X and Y expands do not.

ofst

)/(X+X

ofst

)}

The X5 D/A output may not be expanded.

X (RCOSØ) Output

The analog output, X+X (RCOSØ) BNC connector. An input signal equal

, is available at the X

ofst

The Phase Output voltage is 50 mV per degree with a resolution of 2.5 mV or 1/20 of a degree. The output range is from -180 to +180 degrees. The phase output is updated every 3.5 mS. To achieve maximum accuracy, the magnitude, R, should be as large a fraction of full scale as

possible. If R is less than 0.5% of full scale, the phase output defaults to zero degrees.

The Phase Output may not be expanded and the OFFSET keys do not offset the Phase Output. However, the Phase Output can be offset using the Reference Phase shift.

The Reference Phase shift, which may be adjusted via the phase controls in the reference section, rotates the lock-in's internal coordinate axes relative to the reference input. The Phase Output is the phase difference between the signal and the lock-in's coordinate system. For example, if a signal exactly in phase with the reference input is being measured and the Reference Phase shift is zero, the Phase Output will be zero also. This is because the lock-i n coordinate system is in phase with the reference input and signal. If the Reference Phase shift is set to +45 degrees, then the lock-in coordinate system rotates to +45 degrees from the reference input. Thus, the reference input is now at -45 degrees from the lock-in coordinate axes. Since the reference and signal are in phase, the signal is now at -45 degrees with respect to the lock-in coordinates and the Phase Output will be -45 degrees.

The sum of the Reference Phase shift and the Phase Output is the absolute phase difference between the signal and the reference input. Therefore, the Phase Output may be offset to zero by adjusting the Reference Phase shift. This is sometimes necessary when the Phase Output is near 180 degrees and varies between +180 and 180 degrees.

Output Channel 2

The CHANNEL 2 output is available at the right hand OUTPUT BNC connector. The output parameter is selected by the DISPLAY setting and can be Y, Y OFST, Ø (phase), Ø (phase), Y NOISE, or X6 (ext D/A). All outputs are ±10V full scale when the EXPAND is off. With the EXPAND on, the output is multipled by 10, effectively increasing the full scale sensitivity by 10. (Ø and X6 may not be expanded). The Ø (phase) output is 50 mV/deg (20 deg per Volt) up to ±9 V (±180 deg). The output impedance is <1Ω and the output current is limited to 20 mA.

The right hand analog meter always displays the CHANNEL 2 OUTPUT voltage. Accuracy is 2% of full scale.

The CHANNEL 2 LCD display provides a read-out of the displayed parameter in real units. The scale of the displayed quantity is indicated by the four scale LED's to the right of the display. This readout auto ranges and will reflect the sensitivity added when the EXPAND function is on. When displaying X6, the scale LED's are off and the units are volts.

Rel Channel 2

The REL function and the manual OFFSET are both ways to enter the offset value. After using the REL key, the offset may be adjusted using the manual OFFSET.

When the DISPLAY is Y, Y OFST, or Y NOISE, the REL key sets the Y OFFSET (which affects the Y (RSINØ) output). If Y NOISE is being displayed, the REL function zeroes Y and the noise output will require a few seconds to settle again.

The REL key zeroes the X6 output when the

DISPLAY is D/A.

Auto Phase

When the DISPLAY is Ø (phase), the REL key sets the Reference Phase Shift to the absolute phase difference between the signal and the reference. This is done by setting the Reference Phase Shift to the sum of the Reference Phase Shift and the present Phase Output. After autophase is performed, the Ø output will be 0 deg, R will be unchanged, X will be maximized, and Y will be minimized.

Offset Channel 2

The OFFSET section controls the manual offset. The offset is turned ON and OFF using the upper key in the OFFSET section. When the offset is ON, the lower two keys are used to set the amount of offset. A single key press will advance the offset by 0.025% of full scale. If the key is held

down, the offset advances in larger and larger increments, the largest increment being 10% of full scale. When the offset is turned OFF the applied offset returns to zero but the offset value is not lost. The next press of the upper offset key (return to ON) sets the offset to the previously entered value.

If an attempt is made to advance the offset value beyond full scale, the ON LED will blink. An offset up to 1.024 times the full-scale sensitivity may be entered. When the EXPAND is on, this is 10X the full scale output.

= 10Ae(AvVisinØ+Vos) {if the output is Y}

out

where... Ae= 1 or 10 per the Expand

Av= 1/Sensitivity Vi= magnitude of the signal Ø = phase between signal & reference Vos= offset (fraction of FS < 1.024)

Y (RSINØ) Output

The analog output, Y+Y (RSINØ) BNC connector. An input signal equal in

magnitude to the selected sensitivity which is 90° out of phase with the reference oscillator will generate a 10V output. The output impedance is <1Ω and the output current is limited to 20 mA.

The Y (RSINØ) output is affected by the Y offset but may not be expanded. The Y (RSINØ) is not affected by the DISPLAY setting except for two cases. When the DISPLAY is set to Y OFST, the

Y (RSINØ) output is the Y offset. When the DISPLAY is set to Y NOISE, the Y (RSINØ) output

has a bandwidth equal to the ENBW (1 or 10 Hz) instead of the time constant.

, is available at the Y

ofst

Reference Input

The REFERENCE INPUT BNC is located in REFERENCE INPUT section. The input is ac

coupled and the impedance is 1 MΩ. The dc voltage at this input should not exceed 100 V and the largest ac signal should be less than 10 V peak.

Trigger Level

The TRIGGER MODE indicator toggles from POSITIVE to SYMMETRIC to NEGATIVE when

the TRIGGER MODE key is pressed.

When the DISPLAY is Y, Y OFST, or Y NOISE, the OFFSET keys adjust the Y OFFSET (which affects the Y (RSINØ) output). When the DISPLAY is Ø, the OFFSET keys do nothin g. When the DISPLAY is X6, the OFFSET up and down keys set the output voltage of D/A output X6 (also on the rear panel) up to ±10.24V.

Expand Channel 2

The output EXPAND is toggled by pressing the key in the Channel 2 EXPAND section. The expand status is indicated by the X10, expand on, and the X1, expand off, LED's. Only the Channel 2 OUTPUT is affected, the Y (RSINØ) output is not expanded. Ø and X6 may not be expanded.

If the center TRIGGER MODE LED is on, the mode is SYMMETRIC and the reference oscillator will lock to the positive zero crossings of the ac reference input. The ac signal must be symmetric (e.g. sine wave, square wave, etc.) and have a peak to peak amplitude greater than 100 mV. A signal with 1 Vrms amplitude is recommended. The phase accuracy of the reference channel is specified for a 1Vrms sinewave in the symmetric trigger mode.

If the upper TRIGGER MODE LED is on, the mode is POSITIVE. The trigger threshold is +1V and the reference oscillator will lock to the positive going transitions of the reference input. This mode triggers on the rising edges of a TTL type pulse train. The pulse width must be greater than 1 µS.

If the lower TRIGGER MODE LED is on, the mode is NEGATIVE. The trigger threshold is -1V and the reference oscillator will lock to the negative

going transitions of the reference input. This mode triggers on a negative pulse train or on the falling edges of a TTL type pulse train (remembering that the input is ac coupled). The pulse width must be greater than 1 µS.

Reference Mode

The REFERENCE MODE indicator toggles between f and 2f whenever the MODE key is pressed. When the MODE is f, the lock-in will detect signals at the reference input frequency. When the MODE is 2f, the lock-in detects signals at twice the reference input frequency. In either case, the reference oscillator has a maximum frequency of 100 KHz, thus, when in the 2f mode, the reference input frequency may not exceed 50 KHz.

Reference Display

The REFERENCE DIGITAL DISPLAY shows either the reference oscillator frequency or phase shift. The displayed parameter toggles between the two whenever the SELECT key is pressed. The appropriate scale indicator below the display will be on. It is useful to check the frequency display to verify that the lock-in has correctly locked to your reference. The reference frequency is measured to 1 part in 256 resolution at all frequencies. The display reads .000 if there is no reference input and 199.9 kHz if the input frequency exceeds 105 kHz.

Phase Controls

The phase shift between the reference oscillator of the lock-in and the reference input signal is set using the four keys in the PHASE section. The two keys below the FINE label inc r em ent the phase setting in small amounts. A single key press will change the phase by 0.025 degrees in the desired direction. Holding the key down will continue to change the phase with larger and larger steps with the largest step being 10 degrees. The two 90° keys are used to change the phase by 90 degree increments. The upper key will add 90 degrees and the lower key will subtract 90 degrees. Holding both keys down at once sets the phase shift back to zero. The REFERENCE DIGITAL DISPLAY automatically displays the phase whenever any of the PHASE keys are pressed. The phase ranges from -180 degrees to +180 degrees and is the phase delay from the reference input signal.

Time Constant

There are two post demodulator low pass filters, labeled PRE and POST. The PRE filter precedes the POST filter in the output amplifier. Each filter provides 6 dB/oct attenuation.

The PRE filter time constant ranges from 1 mS to

100 S and is selected by the two keys below the PRE filter indicator LED's. Holding down either

key will advance the time constant four times a second in the desired direction.

In many servo applications, no time constant is needed. The SR530 may be modified to reduce the output time constant to about 20 µS. Contact the factory for details.

The POST filter time constant can be set to 1 S or

0.1 S, or can be removed altogether, NONE, using the two keys below the ENBW indicators. When set to NONE, the total attenuation is that of the

PRE filter, or 6 dB/oct. When the POST filter is 1 S or 0.1S, the total attenuation is 12 dB/oct for

frequency components beyond the larger of the POST and PRE filter bandwidths (reciprocal time constant).

Noise Measurements

When the DISPLAY is set to X NOISE Y NOISE, none of the PRE and POST indicator LED's are on. Instead, one of the two ENBW indic ators wil l be on, showing the Equivalent Noise Bandwidth of the rms noise calculation. The ENBW is set using the keys below the ENBW indicator LED's (same keys as used to set the POST filter). The PRE filter keys do nothing in this case. Pressing the upper key when the bandwidth is already 1 Hz will reset the rms noise average (output) to zero, restarting the calculation. Likewise with pressing the lower key when 10 Hz is already selected.

The noise is the rms deviation of the output within a 1 or 10 Hz equivalent noise bandwidth about the reference frequency. A dc output does not contribute to the noise, the noise is determined only by the ac 'wiggles' at the output. By measuring the noise at different frequ enci es , the frequency dependence of the noise density can be found. This usually has the form of v

The noise computation assumes that the noise has a Gaussian distribution (such as Johnson noise). Since the computation takes many time constants (reciprocal ENBW), the noise output

noise ~

1/f.

should be allowed to approach a steady value before a reading is taken. For the 1 Hz ENBW, this time is on the order of 15 to 30 seconds; for the 10 Hz ENBW, the output stabilizes much faster. The noise output will vary slightly since there will always be noise variations that are slow compared to the bandwidth. Any DC component in the output will not contribute to the noise. However, a large DC output will cause the noise computation to initially rise to a large value before approaching the final answer. As a result, the computation will take longer to settle.

If the OVLD indicator is blinking four times a second, then either the X or Y output is overloaded and the corresponding noise calculation should be ignored. If the OVLD LED is on continuously, then the input signal is overloading the ac amplifier or time constant filters. In this case, both noise outputs will be wrong.

To obtain a value for the noise density, the noise reading should be divided by the square root of the ENBW. Thus, when the ENBW is 1 Hz, the noise output is the noise density, and when the ENBW is 10 Hz, the noise density is the noise output divided by √10. For example, if the input noise is measured to be 7 nV with the ENBW set to 1 Hz, the noise density is 7 nV/√Hz. Switching the ENBW to 10 Hz results in a faster measurement and a reading of 22 nV on the output. The noise density is 22 nV/√10 Hz or 7 nV/√Hz. At frequencies » 10 Hz, the noise density should be independent of the ENBW.

Power

This is the instrument's POWER switch. When the power is turned off, the front panel settings are retained so that the instrument will return to the same settings when the power is next turned on. The SR530 always powers up in the LOCAL mode.

The D/A out puts X5 and X6 are not retained during power off. X5 always becomes the RATIO output at power on and X6 is always reset to zero.

the instrument. All displays return to normal after 3 seconds.

Local and Remote

When the instrument is programmed via the computer interface to be in the REMOTE state WITHOUT LOCK-OUT, the LOCAL key will return the instrument to LOCAL front panel control. If the instrument is in the REMOTE WITH LOCK- OUT state, no front panel key will return the status to LOCAL. In this case, a RETURN TO LOCAL command must be sent over the computer interface or the power must be turned off and back on.

Defaults

If the LOCAL key is held down when the POWER is turned on, the instrument settings will be set to the defaults shown below instead of the settings in effect when the power was turned off.

Parameter Setting BANDPASS OUT

LINE OUT LINE X 2 OUT SENSITIVITY 500 mV DYN RES LOW DISPLAYS X Y EXPANDS OFF OFFSETS OFF (value=0) PRE TIME CONSTANT 100 mS POST TIME CONSTANT 0.1 S ENBW 1 Hz REFERENCE MODE f TRIGGER MODE SYMMETRIC REFERENCE DISPLAY FREQUENCY PHASE SHIFT 0°

Whenever default values are used at power up, the red ERR LED will turn on for about 3 seconds. If the ERR LED is on when the instrument is powered on without the LOCAL key down, then the instrument is ignoring the retained settings. This can be due to a low battery.

When the power is turned on, the CHANNEL 1

OUTPUT DIGITAL DISPLAY will show the SERIAL NUMBER of the instrument and the CHANNEL 2 OUTPUT DIGITAL DISPLAY will show the firmware VERSION. The REFERENCE DIGITIAL DISPLAY shows the model number of

SR530 Guide to Operation

Pin Voltage

Current Available

Rear Panel

AC Power

The ac line voltage selector card, line fuse, and line cord receptacle are located in the fuse holder at the left side of the rear panel. See the section, Preparation for Use at the front of this manual for instructions on setting the ac voltage selector and choosing the correct fuse.

GPIB Connector

The SR530 has an IEEE 488 (GPIB) interface built in. The GPIB address is set using SW1 located to the right of the interface connectors. Refer to page 7 for switch setting details.

RS232 Connector

The SR530 has an RS232 interface. The connector is configured as a DCE. The baud rate, parity, stop bits, and echo mode are selected using SW2 located to the right of the interface connectors. Refer to Page 7 for switch setting details.

Signal Monitor Output

This BNC provides the buffered output of the signal amplifiers and filters. This is the signal just before the demodulator. The output impedance is <1Ω. When a full scale input is applied, the peakto-peak amplitude at this output is 20 mV, 200 mV or 2 V for dynamic reserve settings of high, norm, and low, respectively.

Preamp Connector

This 9 pin "D" connector provides power and control signals to external peripherals such as preamplifiers. The available power is described below.

1 +20 100 mA 2 +5 10 mA 6 -20 100 mA

7 Signal ground 8 Digital ground

General Purpose A/D and D/A

There are four analog input ports, labele d X1 through X4. These inputs may be digitized and read via the computer interfaces. The range is -

10.24 V to +10.24 V and the resolution is 2.5 mV. The input impedance is 1 MΩ. A digitization can be performed in about 3 mS but the result may take longer to transmit over the interface being used.

There are two analog output ports, labele d X5 and X6. The voltages at these ports may be programmed via the computer interfaces. The range is -10.24 V to +10.24 V and the resolution is

2.5 mV. The output impedance is <1Ω and the output current is limited to 20 mA.

Ratio

Output X5 is the ratio output when not programmed by the computer interface or set via the front panel. X5 becomes the ratio output whenever the unit is turned on.

The voltage at X5 is the ratio of the Channel 1 Output to the analog voltage at port X1. An output of 10 V corresponds to a ratio of 1. The ratio is computed by digitizing the Channel 1 Output and the voltage at port X1 and then taking the ratio. The resolution is 2.5 mV. For best accuracy, the sensitivity should be set to provide at least a 50% full scale signal and the analog denominator (X1) should be 5V or greater. The ratio is updated approximately every 3 mS. For the Ratio feature to work, the voltage at the denominator input must exceed 40 mV.

When the DISPLAY is set to D/A, the ratio output is 10 times the magnitude, R, divided by X1.

Internal Oscillator

The INTERNAL OSCILLATOR is a voltage controlled oscillator with a sine wave output . To use the oscillator as the reference source, connect

the REF OUTPUT on the rear panel to the REF INPUT on the front panel. The REF OUTPUT is a

1 Vrms sine wave. The SINE OUTPUT may be used as the stimulus to the experiment. The SINE OUTPUT can be set to three amplitudes, 1 V, 100 mV, and 10 mV (rms) using the amplitude switch. The output impedance is 600Ω. The AMP CAL screw adjusts the amplitude.

The oscillator frequency is controlled by the VCO INPUT voltage. A voltage from 0V to 10V will adjust the frequency according to the VCO RANGE selected. Three ranges are available, 1 Hz/V, 100 Hz/V, and 10 KHz/V. The input impedance is 10 kΩ. The FREQUENCY CAL screw adjusts the frequency.

There are four ways to set the frequency:

1) Connect X5 or X6 (D/A outputs) to the VCO INPUT. The frequency can now be set from the front panel by setting the DISPLAY to D/A and adjusting X5 or X6. The frequency is also controllable via the computer interfaces by programming X5 or X6.

2) If the VCO INPUT is left open, then the oscillator will run at the top of its range (i.e. 10 Hz, 1 KHz, or 100 KHz).

3) A 10 KΩ potentiometer may be connected from the VCO INPUT to ground. This pot will then set the frequency.

4) Connect the VCO INPUT to an external voltage source which can provide 0 to 10V.

In all four cases, if the REF OUTPUT is connected to the REFERENCE INPUT on the front panel, the frequency may be read on the front panel REFERENCE DIGITAL DISPLAY or via the computer interfaces.

SR530 Guide to Programming

An example of a multiple command is: G 5; T 1,4; P 45.10 <cr>

The SR530 Lock-in Amplifier is remotely programmable via both RS232 and GPIB interfaces. It may be used with laboratory computers or simply with a terminal. All front panel features (except signal input selection and power) may be controlled and read via the computer interfaces. The SR530 can also read the analog outputs of other laboratory instruments using its four general purpose analog input ports. There are also two programmable analo g outpu t ports available to provide general purpose control voltages.

Communicating with the SR530

Before using either the RS232 or GPIB interface, the appropriate configuration switches need to be set. There are two banks of 8 switches, SW1 and SW2, located on the rear panel. SW1 sets the GPIB address and SW2 sets the RS232 parameters. The configuration switches are read continuously and any changes will be effective immediately. For details on switch settings, see page 7 at the front of this manual.

Command Syntax

Communications with the SR530 use ASCII characters. Commands to the SR530 may be in either UPPER or lower case.

It is not necessary to wait between commands. The SR530 has a command input buffer of 256 characters and processes the commands in the order received. Likewise, the SR530 has an output buffer (for each interface) of 256 characters.

In general, if a command is sent without parameters, it is interpreted as a request to read the status of the associated function or setting. Values returned by the SR530 are sent as a string of ASCII characters terminated usually by carriage return, line-feed. For example, after the above command is sent, the following read commands would generate the responses shown below.

Command Response from the SR530 G <cr> 5<cr><lf>

T 1 <cr> 4<cr><lf> P <cr> 45.10<cr><lf>

The choice of terminating characters sent by the SR530 is determined by which interface is being used and whether the 'echo' feature is in use. The terminating sequence for the GPIB interface is always <cr><lf> (with EOI). The default sequence for RS232 is <cr> when the echo mode is off, and <cr><lf> when the echo mode is on. The terminating sequence for the RS232 interface may be changed using the J command.

A command to the SR530 consists of one or two command letters, arguments or parameters if necessary, and an ASCII carriage return (<cr>) or line-feed (<lf>) or both. The different parts of the command do not need to be separated by spaces. If spaces are included, they will be ignored. If more than one parameter is required by a command, the parameters must be separated by a comma. Examples of commands are:

G 5 <cr> set the sensitivity to 200 nV T 1,4 <cr> set the pre filter to 30 mS F <cr> read the reference frequency P 45.10 <cr> set phase shift to 45.10¡ X 5,-1.23E-1 <cr> set port X5 to -0.123 V

Multiple commands may be sent on a single line. The commands must be separated by a semicolon (;) character. The commands will not be executed until the terminating carriage return is sent.

Note that the terminating characters are sent with each value returned by the SR530. Thus, the response to the command string G;T1;P<cr> while using the RS232 non-echo mode would be 5<cr>4<cr>45.10<cr>.

Front Panel Status LED's

The ACT LED flashes whenever the SR530 is sending or receiving characters over the computer interfaces.

The ERR LED flashes whenever an error has occurred, such as, an illegal command has been received, a parameter is out of range, or a communication buffer has exceeded 240 characters. This LED flashes for about three seconds on power-up if the battery voltage is insufficient to retain previous instrument settings.

The REM LED is on whenever the SR530 is programmed to be in the remote state.

RS232 Echo and No Echo Operation

In order to allow the SR530 to be operated from a terminal, an echo feature has been included which causes the unit to echo back commands received over the RS232 port. This feature is enabled by setting switch 6 on SW2 to the DOWN position. In this mode, the SR530 will send line-feeds in addition to carriage returns with each value returned and will also send the prompts 'OK>' and '?>' to indicate that the previous command line was either processed or contained an error. Operating the SR530 from a terminal is an ideal way to learn the commands and responses before attempting to program a computer to control the SR530. When the unit is controlled by a computer, the echo feature should be turned off to prevent the sending of spurious characters which the computer is not expecting.

Try-Out with an ASCII Terminal

Before attempting any detailed programming with the SR530, it is best to try out the commands using a terminal. Connect a terminal with an RS232 port to the RS232 connector on the rear panel of the SR530. A 'straight' RS232 cable is required since the SR530 is a DCE and the terminal is a DTE. Set the baud rate, parity, and stop bits to match the terminal by setting SW2 per the switch setting table given on page 7. The echo mode should be enabled (switch 6 DOWN). After setting SW2 and connecting the terminal, hold down the LOCAL key while turning the unit on. This causes the SR530 to assume its default settings so that the following discussion will agree with the actual responses of the SR530. The ACT and ERR LED's on the front panel will flash for a second and the sign-on message will appear on the terminal. Following the message, the prompt 'OK>' will be displayed. This indicates that the SR530 is ready to accept commands.

DIGITAL DISPLAY. Typing the phase read command, P<cr>, will now return the string 45.00 to the terminal.

Now read the gain using the sensitivity read command, G<cr>. The response should be 24 meaning that the sensitivity is at the 24th setting or 500 mV. Change the sensitivity by typing G19<cr>. The sensitivity should now be 10 mV. Check the front panel to make sure this is so.

The Channel 1 Output of the lock-in is read by typing the command, Q1<cr>. The response is a signed floating point number with up to 5 significant digits plus a signed exponent. Change the gain to 10 uV using the G10 command. The response to the Q1 command will now be similar to the previous one except that the exponent is different.

Attach a DC voltmeter to the X6 output on the rear panel. The range should allow for 10V readings. The voltage at the X6 output can be set using the X6 command. Type X6,5.0<cr> and the X6 output will change to 5.0V. To read this back to the terminal, just type X6<cr>. When setting the X6 voltage, the voltage may be sent as an integer (5), real (5.000), or floating point (0.500E1) number. Now connect the X6 output to the X1 input (a ls o on the rear panel). X1 through X4 are analog input ports. To read the voltage on X1, simply type X1<cr>. The response 5.000 should appear on the terminal. The analog ports X1 through X6 can be used by your computer to read outputs of other instruments as well as to control other laboratory parameters.

At this point, the user should experiment with a few of the commands. A detailed command list follows.

Type the letter 'P' followed by a carriage return (P<cr>). The SR530 responds by sending to the terminal the characters 0.00 indicating that the phase is set to 0 degrees. In general, a command with no arguments or parameters reads a setting of the unit. To set the phase to 45 degrees, type the command, P45<cr>. To see that the phase did change, use the SELECT key on the front panel to display the phase on the REFERENCE

SR530 Command List

The leading letters in each command sequence specify the command. The rest of the sequence consists of parameters. Multiple parameters are separated by a comma. Those parameters shown in {} are optional while those without {} are required. The variables m and n represent integers while v represents a real number. Parameters m and n must be expressed in integer format while v may be in integer, real, or floating point format.

AX AY AR AP

The A command causes the auto offset (rel) function to execute. Auto offset is performed by reading the output and using that value as the appropriate offset. Every time an "AX" command is received, the auto offset function is executed on the X output. The "AY" command auto offsets the Y output. The "AR" command auto offsets the R output. Note that "AX" and "AY" will affect the R output but "AR" will not affect X and Y. The "AP" command will execute the auto-phase routine. This is done by setting the reference phase shift with the present phase difference between the signal and the reference input. The ¯ output then reads zero and the reference display reads the signal phase shift. "AP" maximizes X and minimizes Y but R is unaffected. The A commands may be issued at any time, regardless of the DISPLAY setting.

B {n}

If n is "1", the B command sets the bandpass filter in. If n is "0", the bandpass filter is taken out. If n is absent, then the bandpass filter status is returned.

C {n} If n is "1", the C command sets the reference LCD display to show the phase setting. If n is "0", the

LCD will display the reference frequency. If n is absent, the parameter being displayed (frequency or phase) is returned. Note that the P and F commands are used to read the actual values of the phase and frequency.

D {n} If n is included, the D command sets the dynamic reserve. If n is absent, the dynamic reserve

setting is returned.

nDyn 0LOW 1 NORM 2 HIGH

Note that not all dynamic reserve settings are allowed at every sensitivity.

E m {,n}

The E command sets and reads the status of the output expands. If m is "1", then Channel 1 is selected, if m is "2", Channel 2 is selected. The parameter m is required. If n is "1", the E command expands the selected output channel. If n is "0", the expand is turned off for the selected channel. If n is absent, the expand status of the selected channel is returned. Note that the expands do not affect the X and Y BNC outputs, only the Channel 1 and 2 outputs.

The F command reads the reference frequency. For example, if the reference frequency is 100 Hz, the F command returns the string "100.0". If the reference frequency is 100.0 kHz, the string "100.0E+3" is returned. The F command is a read only command.

G {n}

If n is included, the G command sets the gain (sensitivity). If n is absent, the gain setting is returned.

n Sensitivity 1 10 nV 2 20 nV 3 50 nV 4 100nV 5 200nV 6 500nV 71 µV 82 µV 95 µV 10 10 µV 11 20 µV 12 50 µV 13 100µV 14 200µV 15 500µV 16 1 mV 17 2 mV 18 5 mV 19 10 mV 20 20 mV 21 50 mV 22 100mV

Res

23 200mV 24 500mV

Note that sensitivity settings below 100 nV are allowed only when a pre-amplifier is connected.

The H command reads the pre-amplifier status. If a pre-amplifier is connected, a "1" is returned, otherwise, a "0" is returned. The H command is a read only command.

I {n} If n is included, the I command sets the remotelocal status. If n is absent, the remote-local status

is returned.

nStatus 0 Local: all front panel keys are operative 1 Remote: front panel keys are not

operative. The LOCAL key returns the status to local.

2 Lock-out: front panel keys are not

operative. No key returns the status to local. Another I command is needed to return to local.

When using the GPIB interface, the REN, LLO, and GTL commands are not implemented. The I command is used by both interfaces to set the remote-local status.

J {n1,n2,n3,n4}

The J command sets the RS232 end-of-record characters sent by the SR530 to those specified by the decimal ASCII codes n1-n4. If no argument is included, the end-of-record sequence returns to the default (a carriage return), otherwise, up to four characters may be specified. The end-ofrecord required by the SR530 when receiving commands is not affected.

K n The K command simulates a front panel key press. The effect is exactly the same as pressing

the selected key once. The parameter n is required.

nKey 1 Post Time Constant Up 2 Post Time Constant Down 3 Pre Time Constant Up 4 Pre Time Constant Down 5 Select Display (f/phase)

690° Up 790° Down 8 Zero Phase (Simultaneous 90° Up and

Down) 9 Reference Trigger Mode 10 Reference Mode (f/2f) 11 Degrees Up 12 Degrees Down 13 Channel 2 Rel 14 Channel 2 Offset (On/Off) 15 Channel 2 Offset Up 16 Channel 2 Offset Down 17 Channel 2 Expand 18 Output Display Up 19 Output Display Down 20 Channel 1 Expand 21 Channel 1 Rel 22 Channel 1 Offset (On/Off) 23 Channel 1 Offset Up 24 Channel 1 Offset Down 25 Dyn Res Up 26 Dyn Res Down 27 Sensitivity Up 28 Sensitivity Down 29 Local 30 Line X 2 Notch Filter 31 Line Notch Filter 32 Bandpass Filter

L m {,n}

The L command sets and reads the status of the line notch filters. If m is "1", then the 1X line notch is selected, if m is "2", the 2X line notch is selected. The parameter m is required. If n is "1", the L command sets the selected filter in. If n is "0", the selected filter is taken out. If n is absent, the status of the selected filter is returned.

M {n} If n is "1", the M command sets the reference mode to 2f. If n is "0", the reference mode is set

to f. If n is absent, the reference mode is returned.

N {m}

If m is "1", the N command sets the ENBW to 10 Hz. If m is "0", the ENBW is set to 1 Hz. If m is absent, the ENBW setting is returned.

OX {n} {,v} OY {n} {,v} OR {n} {,v}

The "OX", "OY", and "OR" commands set the offsets for the X, Y, and R outputs respectively. If n is "1", the offset is turned on. If n is "0", the offset is turned off. If n and v are absent, the offset status (on or off) is returned. (The value of the offset is read using the S and Q commands.)

If n is included, then v may be sent also. v is the offset value up to plus or minus full scale in units of volts. For example, to offset half of full scale on the 100 µV sensitivity, v should be "50.0E-6" or an equivalent value. However, if the sensitivity is then changed to 200 µV, the offset is now half of the new full scale or 100 µV. When the sensitivity is changed, the offset is preserved as a constant fraction of full scale rather than as a voltage referred to the input. The expand function will, on the other hand, preserve the value of the offset as an input referred voltage. Once a value of v is sent, the offsets may be turned off and on without losing the offset values by using the O commands without the v parameter. Note that the X and Y offsets will affect the R output but the R offset does not affect the X or Y output.

P {v}

If v is absent, the P command returns the reference phase shift setting from -180 to +180 degrees. When v is included, the phase is set to the value of v up to ±999 degrees.

Q1 Q2 QX QY

The Q commands return the output values in units of volts or degrees. For an input signal of 50 µV on a full scale sensitivity of 100 µV, a Q command will return the string "50.00E-6". "Q1" and "Q2" read the parameters being shown on the Channel 1 and Channel 2 output displays as selected with the S command. "QX" and "QY" read the X (RCOS Ø) and Y (RSIN Ø) BNC outputs.

R {n}

If n is included, the R command sets the reference input trigger mode. If n is absent, the trigger mode is returned.

2R Ø 3 R Offset Ø 4 X Noise Y Noise 5 X5 (D/A) X6 (D/A)

T m {,n}

The T command sets and reads the status of the time constants. If m is "1", the pre time constant is selected, if m is "2", the post time constant is selected. The parameter m is required. If n is included, the T command sets the selected time constant. If n is absent, the setting of the selected time constant is returned.

n Pre Time Constant (m=1)

11 mS

23 mS

3 10 mS

4 30 mS

5 100 mS

6 300 mS

71 S

83 S

9 10 S

10 30 S

11 100 S

n Post Time Constant (m=2)

0 none

1 0.1 S

21 S

U m {,n}

The U command sets and reads the unit's calibration bytes. m is the address offset of the byte, 0-511. If n is absent, the value of the addressed calibration byte is returned. If n is included, the addressed calibration byte is set to the value of n, 0-255. The new value will be in effect until the power is turned off or a reset command is issued. Use of this command is not recommended.

n Mode 0 ositive 1 Symmetric 2 Negative

S {n}

If n is included, the S command selects the parameters shown on the Channel 1 and 2 analog meters, output digital displays, and output BNC's. If n is absent, the displayed parameter is returned.

n Channel 1 0X Y 1 X Offset Y Offset

Channel 2

V {n}

If n is included, the V command sets the GPIB SRQ (service request) mask to the value n (0-

255). If n is absent, the value of the SRQ mask is returned.

W {n}

The W command sets and reads the RS232 character wait interval. If n is included, the SR530 will wait nx4 mS between characters sent over the RS232 interface. This allows slow computer interfaces to keep up. n can range from 0 to 255. If n is absent, the wait value is returned. The wait interval is set to 6 on power-up.

X n {,v} n designates one of the 6 general purpose analog ports located on the rear panel. If n is 1,2,3, or 4,

the X command will return the voltage on the designated analog input port (X1-X4) in volts. If n is 5 or 6, then v may also be sent. If v is included, the designated analog output port (X5 or X6) will be set to v volts where v has the range -10.238V to +10.238V. If v is absent, the output value of the selected port is returned. On power-up, port X5 is the ratio output. An "X 5" command will read the ratio output. An "X 5" command with the parameter v will set port X5 to v volts, overriding the ratio output. Port X5 will return to the ratio output on power-up or reset.

Y {n}

The Y command reads the status byte. (See the following section for a definition of the Status Byte.) n designates one bit, 0-7, of the status byte. If n is included, the designated bit of the status byte is returned. The bit which is read is then reset. If n is absent, the value of the entire byte is returned and all status bits are then reset. This status byte may also be read over the GPIB using the serial poll command.

The Z command causes an internal reset. All settings return to the default values shown on page 15. The ERR LED will be on for about three seconds to indicate that the stored instrument settings are being ignored. If the RS232 echo mode is on, the sign-on message is sent over the RS232 interface.

Status Byte

The SR530 maintains an 8-bit status register which the user may read to obtain information on the unit's status. The status byte may be read in two ways: by sending the Y command, which returns the value of the byte in ASCII coded decimal, or, when using the GPIB, by performing a serial poll. The returned status byte reflects all of the status conditions which have occurred since the last time the byte was read. After the status byte has been read, it is cleared. Thus, the status byte should be read initially to clear all previous conditions (especially after a power up or after settings have been changed).

The definitions for each bit of the status byte are given below:

Bit 0

Not Used

Bit 1

Command Parameter Out of Range. This bit is

set if a parameter associated with a command is not in the allowed range.

Bit 2

No Reference. This bit is set when no reference

input is detected, either because the amplitude is too low or the frequency is out of range.

Bit 3

Unlock. This bit is set when the reference

oscillator is not locked to the reference input. If there is no reference input, bit 2 (no reference) will be set but bit 3 (unlock) may not be.

Bit 4

Overload. This bit is set if there is a signal

overload. This can happen when the sensitivity is too high, the dynamic reserve is too low, the offset is on, or the expand is on. Overloads on the general purpose A/D inputs or the ratio output are not detected.

Bit 5

Auto Offset Out of Range. This bit is set if the

auto offset function cannot zero the output because the output exceeded 1.024X full scale.

Bit 6

SRQ. This bit is set if the SR530 has generated

an SRQ on the GPIB interface. This bit is reset after the SR530 has been serial polled. This bit is set only for status reads via a serial poll, ie., Bit 6 always zero for the RS232 .

Bit 7

Command Error. This bit is set when an illegal

command string is received.

Errors

Whenever a 'parameter out of range' or an 'unrecognized command' error occurs, the appropriate status bits are set and the ERR LED flashes. In addition, any commands remaining on the current command line (up to the next <cr>) are lost. The ERR LED will also light if any of the internal communication buffers overflows. This occurs when 240 characters are pending on the command queue or output queue. The ERR LED will go off as soon as all buffers drop below 200

characters again.

Reset

The Z command resets the unit to its default state. The default front panel settings are listed in the DEFAULTS section of the Guide to Operations. In addition, the interface status returns to LOCAL, the SRQ mask is cleared, the RS232 character WAIT interval is set to 6, and the terminating sequence is reset to the proper defaults.

The command and output buffers are cleared by the Z command. Therefore, it is bad practice to use the Z command before all previous commands have been processed and all responses have been received.

Trouble-Shooting Interface Problems

If you are having difficulty getting your computer to communicate with the SR530 look to the sections on the RS232 and GPIB interfaces for some tips specific to your particular interface.

An ASCII terminal is a valuable aid for debugging interface problems. You can use it to:

1) become familiar with the SR530's command structure,

2) see GPIB bus transactions by using the GPIB echo mode,

3) eavesdrop on transactions when using the RS232 interface,

4) substitute a human for the SR530 by using a null modem cable ( to make the DTE a DCE) and attaching the terminal to the port to which you would normally have connected the SR530. This allows you to test your program's responses to inputs which you provide from the terminal.

Common Hardware Problems include:

mode should be off when not debugging the GPIB interface.)

3) Your computer requires an RS232 control line to be asserted, but your cable does not pass it between the SR530 and the computer, or, your computer is not asserting the DTR line on the RS232.

Common Software Problems include:

1) You have sent the wrong command to ask for data from the SR530. Your program will wait forever for a response which is not going to come. This may not be your fault; we have seen Microsoft's Interpreted Basic on the IBM PC occasionally send a curly bracket (ASCII 253) when it was supposed to have sent a carriage return (ASCII 13).

2) Your computer's baud rate has been changed and no longer matches the SR530's baud rate.

3) The initial command sent to the SR530 was invalid due to a garbage character left in the command queue from power-up, or, the first character in you computer's UART is garbage, also due to power-up. It is good practice to send a few carriage returns to the SR530 when your program begins, and have your program clear-out its UART at the start of your program.

4) The SR530 is not sending the correct 'end-of- record' marker for your computer. For example, it appears that Microsoft's Rev 3.2 FORTRAN on the IBM PC under DOS 2.1 requires two carriage returns for an end-of-record marker. The J command can be used to set the SR530 end-ofrecord marker to 2 carriag e returns. [The end-of-record marker is that sequence which indicates that the response is complete. From the keyboard, a single carriage return is the end-of-record marker.]

1) The RS232 or GPIB cables are not properly attached.

2) The configuration switches for the RS232 characteristics or GPIB address are not set correctly (Make sure the RS232 echo is off when using the RS232 interface with a computer. The GPIB with RS232 echo

5) Answers are coming back from the SR530 too fast, overwriting the end-of-record markers, and causing the computer to hang waiting for a complete response. In this case, the W command can be used to slow down the response time of the SR530 preventing overwriting.

6) Answers are coming back from the SR530 too slowly due to the W6 default setting for the character interval time. Use the W command to speed up the transmission from the SR530. This can cause problems for the GPIB interface if the echo mode is on (switch 6 of SW1).

The SR530 with the RS232 Interface

command is:

J {n1,n2,n3,n4}

where n1, n2, n3, and n4 are decimal values between 0 and 255 corresponding to the ASCII codes of the desired termination characters. For instance, if the desired termination sequence is an asterisk, (ASCII 42), two carriage returns, (ASCII

13), and a line-feed, (ASCII 10), the appropriate command is:

The RS232 is a popular serial interface standard for bit serial communication. Despite the existence of the standard there are many permutations of control lines, baud rates, and data formats. If you do not have a lot of experience interfacing RS232 equipment you should read Appendix B for a description of the RS232 and interfacing tips.

Data Communications Equipment (DCE)

The SR530 is configured as DCE so that it may be connected directly to a terminal. If the SR530 is to be interfaced with another DCE device, a special cable (sometimes referred to as a 'modem' cable) is required. To use the RS232 interface you must set the switches in SW2 to match your computer's baud rate, parity, and number of stop bits. Refer to Page 7 for details.

Wait Command

The SR530 normally waits until the RS232 'Clear to Send' control line (CTS) is asserted before sending characters. However, some computers do not set and reset the CTS line, possibly causing the SR530 to send data when the computer is not ready to read it. The SR530 may be 'slowed down' using the W command. Sending 'Wn' causes the unit to wait nx4 mS before sending each character over the RS232 bus. The command W0 sets the wait interval to zero and results in the fastest transmission. The wait interval is set to 6 (24 mS)on power-up.

J 42,13,13,10

If a G command is sent requiring an answer of 24 (sensitivity = 500 mV), the SR530 would respond with the string

24*<cr><cr><lf>

Up to four terminating characters may be specified by the J command. If no arguments are sent with the J command, the terminating sequence returns to the default (echo on: <cr><lf>; echo off: <cr>).

The J command does not affect the terminating character (<cr>) required at the end of commands received by the SR530. It also does not affect the terminating sequence sent with data over the GPIB interface.

The SR530 with the GPIB Interface

For a brief introduction to the GPIB standard, please read Appendix C at the back of this manual. Before using the GPIB interface you must set the switches in SW1 per the instructions on page 7.

GPIB Capabilities

The GPIB capabilities of the SR530 consistent with IEEE standard 488 (1978) are shown in the table below. Also shown are the responses of the SR530 to some standard commands.

Termination Sequences

The default RS232 termination characters are sufficient to interface with most computers, however, it will occasionally be necessary to send special terminating sequences to fit the requirements of some computers. This can be done with the J command. The format for the

Code Function SH1 Source handshake cap ab ility AH1 Acceptor handshake capability T5 Basic Talker, Serial Poll, Unaddressed to

talk if addressed to listen

L4 Basic Listener, Unaddressed to listen if

addressed to talk SR1 Service request capability PP0 No parallel poll capability

DC1 Device Clear capabilit y RL0 REN,LLO, GTL not implemen ted.

'I' command sets Remote-Local. SR530 Response to GPIB Commands Mnemonic Command Response

DCL Device Clear Same as Z command SDC Selected Same as Z command

Device Clear

SPE Serial Poll Send Status Byte,

Enable & clear status byte

Because the SR530 can be controlled by an RS232 interface as well as the GPIB, the remotelocal functions are not standard. There is no local with lock out state. When in the local state, remote commands are processed, even without the REN command being issued. This is because the RS232 interface has no provision for bus commands and remote commands over the RS232 interface would never be enabled.

Serial Polls and Service Requests

The status byte sent by the SR530 when it is serial polled is the same status byte which is read using the Y command (except for bit 6, SRQ). Ofcourse, when the SR530 is serial polled, it does not encode the status byte as a decimal number. The SR530 can be programmed to generate a service request (SRQ) to the GPIB controller every time a given status condition occurs. This is done using the V{n} command. The mask byte, n (0-255), is the SRQ mask byte. The mask byte is always logically ANDED with the status byte. If the result is non-zero, the SR530 generates an SRQ and leaves the status byte unchanged until the controller performs a serial poll to determine the cause of the service request. When the unit has been serial polled, the status byte is reset to reflect all of the status conditions which have occurred since the SRQ was generated.

Any SRQ generated by the 'no reference, 'unlock', 'overload', and 'auto over-range' conditions will also reset the corresponding bit in the SRQ mask byte. This is to prevent a constant error condition (such as no reference applied to the input) from continually interrupting the controller. When such an SRQ occurs, the controller should change some parameter so as to solve the problem, and then re-enable the SRQ mask bit again using the V command.

GPIB with RS232 Echo Mode

It is sometimes useful when debugging a GPIB system to have some way of monitoring exactly what is going back and forth over the bus. The SR530 has the capability to echo all characters sent and received over the GPIB to its RS232 port. This mode of operation is enabled by setting switch 6 of SW1 to the DOWN position. The baud rate, stop bits, and parity of the RS232 port are still set by SW2. Of course, the RS232 port operates at much lower speeds than the GPIB and will slow down the GPIB data rate in this mode. (Use the W0 command to allow the RS232 interface to run at full speed, otherwise, the GPIB transactions may take so long that the controller can hang.) During actual use, this mode should be disabled.

The SR530 with BOTH Interfaces

If both interfaces are connected, commands may be received from either interface. Responses are always sent to the source of the request (except in GPIB echo mode). It is unwise to send commands from the two interfaces at the same time since the characters from different sources can become interleaved on the command queue and result in 'unrecognized command' errors.

For example, if we want to generate an SRQ whenever there is an overload or unlock condition, we need an SRQ mask byte equal to 00011000 binary, or 24 decimal ("V24" command). The byte 00011000 binary corresponds to the status byte with the 'no reference' and 'unlock' status bits set. If an overload occurs, then an SRQ will be generated. The serial poll will return a status byte showing SRQ and overload. If an unlock condition occurs before the serial poll is concluded, another SRQ will be generated as soon as the serial poll is finished. A second serial poll will reflect the unlock condition.

The Lock-in Technique

The Lock-in technique is used to detect and measure very small ac signals. A Lock-in amplifier can make accurate measurements of small signals even when the signals are obscured by noise sources which may be a thousand times larger. Essentially, a lock-in is a filter with an arbitrarily narrow bandwidth which is tuned to the frequency of the signal. Such a filter will reject most unwanted noise to allow the signal to be measured. A typical lock-in application may require a center frequency of 10 KHz and a bandwidth of 0.01 Hz. This 'filter' has a Q of 10 well beyond the capabilities of passive electronic filters.

In addition to filtering, a lock-in also provides gain. For example, a 10 nanovolt signal can be amplified to produce a 10 V output--a gain of one billion.

All lock-in measurements share a few basic principles. The technique requires that the experiment be excited at a fixed frequency in a relatively quiet part of the noise spectrum. The lock-in then detects the response from the experiment in a very narrow bandwidth at the excitation frequency.

Applications include low level light detection, Hall probe and strain gauge measurement, micro-ohm meters, C-V testing in semiconductor research, electron spin and nuclear magnetic resonance studies, as well as a host of other situations which require the detection of small ac signals.

A Measurement Example

Suppose we wish to measure the resistance of a material, and we have the restriction that we must not dissipate very much power in the sample. If the resistance is about 0.1Ω and the current is restricted to 1 µA, then we would expect a 100 nV signal from the resistor. There are many noise signals which would obscure this small signal -60Hz noise could easily be 1000 times larger, and dc potentials from dissimilar metal junctions could be larger still.

In the block diagram shown below we use a 1Vrms sine wave generator at a frequency wr as

our reference source. This source is current limited by the 1 MΩ resistor to provide a 1 µA ac excitation to our 0.1Ω sample.

Two signals are provided to the lock-in. The 1VAC reference is used to tell the lock-in the exact frequency of the signal of interest. The lock-in's Phase-Lock Loop (PLL) circuits will track this input signal frequency without any adjustment by the user. The PLL has two outputs, cos(wrt) and

sin(wrt).

The signal, Vs cos(wst+Ø), from the sample under test is amplified by a high gain ac coupled

differential amplifier. The output of this amplifier is multiplied by the PLL outputs in two PhaseSensitive Detectors (PSD1 and PSD2). This multiplication shifts each frequency component of the input signal, ws, by the reference frequency,

wr, so that the output of the PSD's are given by:

Vpsd1 = Vs cos(wrt) cos(wst+Ø) = 1/2 Vs cos[(wr + ws)t+Ø] + 1/2 Vs cos[(wr - ws)t+Ø]

Vpsd2 = Vs sin(wrt) cos(wst+Ø) = 1/2 Vs sin[(wr + ws)t+Ø] + 1/2 Vs sin[(wr - ws)t+Ø]

The sum frequency component of each PSD is attenuated by a low pass filter, and only those difference frequency components within the low pass filter's narrow bandwidth will pass through to the dc amplifiers. Since the low pass filter can have time constants up to 100 seconds, the lock-in can reject noise which is more than .0025 Hz away from the reference frequency input.

For signals which are in phase with the reference (¯=0¡), the output of PSD1 will be a maximum and the output of PSD2 will be zero. If the phase is non-zero, Vpsd1 ~ cos(Ø) and Vpsd2 ~ sin(°). The magnitude output is given by,

R = {(V

and is independent of the phase Ø. The phase output is defined as

Ø = - tan-1(V

Thus, a dual-phase lock-in can measure the amplitude of the signal, independent of the phase, as well as measure an unknown phase shift between the signal and the reference.

psd1

)2 + (V

psd2

/ V

)2}

psd1

1/2

)

~ Vs

Understanding the Specifications

The table below lists some specifications for the SR530 lock-in amplifier. Also listed are the error contributions due to each of these items. The specifications will allow a measurement with a 2% accuracy to be made in one minute.

We have chosen a reference frequency of 5 kHz so as to be in a relatively quiet part of the noise spectrum. This frequency is high enough to avoid low frequency '1/f' noise as well as line noise. The frequency is low enough to avoid phase shifts and amplitude errors due to the RC time constant of the source impedance and the cable capacitance.

The full-scale sensitivity of 100 nV matches the expected signal from our sample. The sensitivity is calibrated to 1%. The instrument's output stability also affects the measurement accuracy. For the required dynamic reserve, the output stability is 0.1%/°C. For a 10°C temperature change we can expect a 1% error.

A front-end noise of 7 nV/√Hz will manifest itself as a 1.2 nVrms noise after a 10 second low-pass filter since the equivalent noise bandwidth of a single pole filter is 1/4RC. The output will converge exponentially to the final value with a 10second time constant. If we wait 50 seconds, the output will have come to within 0.7% of its final value.

The dynamic reserve of 60 dB is required by our expectation that the noise will be a thousand times larger than the signal. Additional dynamic reserve is available by using the bandpass and notch filters.

A phase-shift error of the PLL tracking circuits will cause a measurement error equal to the cosine of the phase shift error. The SR530's 1° phase accuracy will not make a significant contribution to the measurement error.

Specifications for the Example Measurement Specification Value Error Full Scale Sensitivity 100 nV

Dynamic Reserve 60 dB Reference Frequency 5 kHz Gain Accuracy 1% 1% Output Stability 0.1%/°C 1% Front-End Noise < 7 nV/√Hz 1.2% Output Time Constant > 10 S 0.7% Total RMS Error 2%

Shielding and Ground Loops

In order to achieve the 2% accuracy given in this measurement example, we will have to be careful to minimize the various noise sources which can be found in the laboratory. (See Appendix A for a brief discussion on noise sources and shielding) While intrinsic noise (Johnson noise, 1/f noise and alike) is not a problem in this measurement, other noise sources could be a problem. These noise sources can be reduced by proper shielding. There are two methods for connecting the lock-in to the experiment: the first method is more convenient, but the second eliminates spurious pick-up more effectively.

In the first method, the lock-in uses the A input in a 'quasi-differential' mode. Here, the lock-in detects the signal as the voltage between the center and outer conductors of the A input. The lock-in does not force A's shield to ground, rather it is connected to the lock-in's ground via a 10Ω resistor. Because the lock-in must sense the shield voltage (in order to avoid the large ground loop noise between the experiment and the lockin) any noise pickup on the shield will appear as noise to the lock-in. For a low impedance source (as is the case here) the noise picked up by the shield will also appear on the center conductor. This is good, because the lock-in's 100 dB CMRR will reject most of this common mode noise. However, not all of the noise can be rejected, especially the high frequency noise, and so the lock-in may overload on the high sensitivity ranges.

appears on both the A & B inputs will not be perfectly cancelled: the common mode rejection ratio (CMRR) specifies the degree of cancellation. For low frequencies the CMRR of 100 dB indicates that the common mode signal is canceled to 1 part

in 10

, but the CMRR decreases by about 6 dB/octave (20 dB/Decade) starting at 1KHz. Even with a CMRR of 10

, a 10 mV common mode

signal behaves like 100nV differential signal. There are some additional considerations in

deciding how to operate the lock-in amplifier: Dynamic Reserve (DR) is the ratio of the largest

noise signal that the lock-in can tolerate before overload to the full-scale input. Dynamic reser ve is usually expressed in dB. Thus a DR of 60 dB means that a noise source 1000 times larger than a full scale input can be present at the input without affecting the measurement of the signal. A higher DR results in a degraded output stability since most of the gain is DC gain after the phase sensitive detector. In general, the lowest DR which does not cause an overload should be used.

Quasi-Differential Connection

The second method of connecting the experiment to the lock-in is called the 'true-differential' mode. Here, the lock-in uses the difference between the center conductors of the A & B inputs as the input signal. Both of the signal sources are shielded from spurious pick-up.

True-Differential Connection

With either method, it is important to minimize both the common mode noise and the common mode signal. Notice that the signal source is held near ground potential in both cases. A signal which

The Current Input has a 1 kΩ input impedance and a current gain of 10

Volts/Amp. Currents from 500 nA down to 100 fA full scale can be measured. The impedance of the signal source is the most important factor to consider in deciding between voltage and current measurements. For high source impedances, (>1 MΩ), and small currents use the current input. Its relatively low impedance greatly reduces the amplitude and phase errors caused by the cable capacitancesource impedance time constant. The cable capacitance should still be kept small to minimize the high frequency noise gain of the current preamplifier.

For moderate source impedances, or larger currents, the voltage input is preferred. A small value resistor may be used to shunt the source. The lock-in then measures the voltage across this resistor. Select the resistor value to keep the source bias voltage small while providing enough signal for the lock-in to measure.

The Auto-Tracking Bandpass Filter has a Q of 5 and follows the reference frequency. The passband is therefore 1/5 of the reference frequency. The bandpass filter can provide an additional 20 dB of dynamic reserve for noise signals at frequencies outside the passband. The filter also improves the harmonic rejection of the lock-in. The second harmonic is attenuated an additional 13dB and higher harmonics are

attenuated by 6 dB/octave more. You may wish to use the bandpass filter and select a low dynamic reserve setting in order to achieve a better output stability. Since the processor can only set the bandpass filter's center frequency to within 1% of the reference frequency, this filter can contribute up to 5° of phase shift error and up to 5% of amplitude error when it is used. In addition, the bandpass filter adds a few nanovolts of noise to the front end of the instrument when it is in use.

In many servo applications, no output filtering is needed. In this case, the SR530 may be modified to reduce the output time constant to about 20 µS. Contact the factory for details.

Noise measurement is a feature which allows direct measurement of the noise density of the signal at the reference frequency. This is a useful feature to assess at what frequency you should run your experiment.

Line Notch Filters should be used in most measurement situations. The filters will reject about 50 dB of line frequency noise (about a factor of 300). If your reference frequency is one octave away, then these filters will introduce a 5° phase shift error, and a few percent amplitude error. Their effect on your signal is negligible if your reference frequency is more than two octaves away.

The frequency range of the SR530 lock-in amplifier extends from 0.5Hz to 100KHz. No additional cards are required for the instrument to cover its full frequency range. The SR530 can be used to detect a signal at the reference frequency or at twice the reference frequency to allow for convenient measurement of the harm onic of the signal.

Output Filters can have one pole (6 dB per octave) or two poles (12 dB/octave). A two-pole filter provides a signal to noise improvement over a single-pole filter due to its steeper roll off and reduced noise bandwidth. Single-pole filters are preferred when the lock-in is used in a servo system to avoid oscillation.

Ratio Capability allows the lock-in's output to be divided by an external voltage input. This feature is important in servo applications to maintain a constant loop gain, and in experiments to normalize a signal to the excitation level.

Computer Interface allows a computer to control and to record data from the instrument. This is the single most important feature for extending the lock-in's capabilities and it's useful lifetime. Measurements which are imprac t ica l wit hout a computer become simple when a computer is used to coordinate various parts of the experiment.

The Internal Oscillator provides a reference source for the lock-in. This allows the lock-in's frequency to be set without an additional signal generator. It also provides a sine wave to be used as the signal stimulus in an experiment. The frequency may be set via the computer interface as well as manually.

SR530 Block Diagram

Several new concepts are used to simplify the design of SR530 lock-in amplif ier . In additi on to implementing recent advanc es in linear int egr ate d circuit technology, the instrument was designed to take full advantage of its microprocessor controller to improve performance and to reduce cost.

As an example of the new techniques used in the SR530, consider the harmonic rejection problem. Previously, lock-in amplifiers used a PLL with a square wave output. The Fourier components of the square wave created a serious problem -- the lock-in would respond to signal and noise at f, 3f, 5f,.ad infinitum. Quite often, one component of

this picket fence of frequencies would land on some noise source, giving a spurious result. To overcome this difficulty designers employed tuned amplifiers or heterodyning techniques. All of these 'fix-ups' had drawbacks, including phase and amplitude errors, susceptibility to drift, and cardswapping to change frequencies.

In contrast, the SR530 detects the signal by mixing a reference sine wave in a precision analog multiplier. Because of the low harmonic content of this sine wave, the instrument is insensitive to harmonics. This approach has eliminated the difficulty, performance compromises, and cost of the older techniques.

The Signal Channel

The instrument has both current and voltage inputs. The current input is a virtual ground, and the 100 MΩ voltage inputs can be used as singleended or true differential inputs.

There are three signal filters. Each of these filters may be switched 'in' or 'out' by the user. The first filter is a line notch filter. Set to either 50 or 60 Hz, this filter provides 50 dB of rejection at the line frequency. The second filter provides 50 dB of rejection at the first harmonic of the line frequency. The third filter is an auto-tracking bandpass filter with a center frequency tuned by the microprocessor to the frequency of the signal. These three filters eliminate most of the noise from the signal input before the signal is amplified.

A high-gain ac amplifier is used to amplify the signal before entering the phase sensitive detector. The high gain which is available from this programmable amplifier allows the lock-in to operate with a lower gain in its dc amplifier. This arrangement allows high stability operation even when used on the most sensitive ranges.

Reference Channel

The processor controlled reference input discriminator can lock the instrument's PLL to a variety of reference signals. The PLL can lock to sine waves or to logic pulses with virtually no phase error. The PLL outputs are phase shifted and shaped to provide two precision sine waves. The two sine waves have 90° of phase shift between them.

Phase Sensitive Detectors

and dc amplifiers will affect the stability and dynamic reserve of the instrument. The output is most stable when most of the gain is in the ac amplifier, however, high ac gain reduces the dynamic reserve.

For the most demanding applications, the user may specify how the system gain is partitioned. However, with prefilters that are able to provide up to 100 dB of dynamic reserve, and with chopper stabilized dc amplifiers, most users will not be concerned with just how the system gain is allocated.

A Microprocessor Based Design

The instrument was designed to take full advantage of its microprocessor controller. This approach provides several key advantages...

The instrument may be interfaced to a laboratory computer over the RS232 and IEEE-488 interfaces. In addition to simply reading data from the lock-in, the computer can control all of the instrument settings with simple ASCII commands.

A key feature of the instrument is its four A/D inputs and two D/A outputs. These analog I/O ports may be used to read and supply analog voltages to an experiment or measurement. All of the input and output ports have a full-scale range of ±10.24VDC with 2.5 mV resolution and 0.05% accuracy.

Computer control can eliminate set-up errors, reduce tedium, allow more complete data recording and post measurement analysis. Also, the computer can play an active role in the data acquisition by adjusting gains, etc., in response to changing measurement con dit ions .

The Phase Sensitive Detectors are linear multipliers which mix the amplified and filtered signal with the reference sine waves. The difference frequency component of the multipliers' outputs are dc signals that are proportional to the amplitude of the signal. The low-pass filters which follow each multiplier can reject any frequency components which are more than a fraction of a Hertz away from the signal frequency.

DC Amplifiers and System Gain

Dc amplifiers amplify and offset the outputs of the two low pass filters. The total syst em gain is the product of the ac and dc amplifier gains. The partitioning of the system gain between these ac

The microprocessor based design eliminates many analog components to improve performance, reliability, and reduce cost. For example, the magnitude and phase outputs are calculated by the microprocessor instead of using an analog vector summer. This eliminates the temperature drifts and inaccur ac ies ass ociat ed with nonlinear analog circuits and greatly reduces the number of parts. Each unit is computer calibrated at the factory, and calibration constants are placed in the instrument's read-only memory. The SR530 has only one-fifth of the analog trimming components that are found in older designs.

Circuit Description

Introduction

The SR530 Lock-in amplifier is an integrated instrument combining state of the art analog design with advanced microprocessor based control and interfaces. This discussion is intended to aid the advanced user in gaining a better understanding of the instrument.

The SR530 has eight main circuit areas: the signal amplifier, the reference osc il lator, the de mod ula tor , the analog output and controls, the front panel, the microprocessor, the computer interfaces, and the power supplies. With the exception of the front panel, the quadrature oscillator and de mod ula tor , and a few pieces of hardware, the entire lock-in is built on a single printed circuit board. Each section is isolated from the others as much as possible to prevent spurious signal pickup. To aid in the location of individual components, the first digit (or first two digits of a four digit part number) of each part number generally refers to the schematic sheet number on which it occurs. To help find the part on the circuit board, the parts list includes a location on the circuit board for each component. Parts with a four-digit part number beginning with 10,11, or 12 are found on the quadrature detector plug-in board located in the center of the main circuit board. Part numbers beginning with 6 refer to parts on the front panel.

Signal Amplifier

Assuming the input selector switch is set to a voltage input, the signal is coupled in through capacitors C101 and C102. The input impedance is set by the 100 MΩ resistors R101 and R102 over the operating frequency range. Note that R103 isolates the signal shields from the instrument ground forcing the return signal current back along the cable shields. The signal is then applied differentially to the gates of Q101. Q101 is a low noise dual JFET. The drain current through R109 is kept constant by 2/2 U101. The other half of U101 maintains a virtual null between the drains of the two transistors and thus an identical current flows through R110. Any input that would cause a differential between the two drains is amplified by 1/2 U101 and fed back via R112 in such a way as to reduce that differential. Since the two transistors are at equal and constant currents, their gate-source potentials are constant. Thus, the fed back signal which appears at the source of the right hand transistor exactly matches the input . Likewise, this signal will match the input

to the left hand transistor but with the opposite sign. Resistors R112 and R110 attenuate the fed back signal from the output of U101 resulting in a differential input, single ended output, fixed gain of 10 amplifier. P101 adjusts the current balance between the two transistors and therefore their gain match and common mode rejection.

The output of the pre-amp is scaled by resistors R119-R122 and analog switch U103 which make up a 1-2-5-10 attenuator. The signal is then amplified by 2/2 U102. Input overload is sensed through diodes D101-D104.

Current Amplifier

When the input selector is set to current, the input to the pre-amp comes from the output of the current to voltage converter, 1/2 U102. U102 is a low voltage-noise bipolar op amp. Q102 serves as an input buffer to provide low current-noise to the input. The op amp always maintains a null at the gates of Q102 thus providing an input impedance of 1KΩ (R128). The input current is converted to a voltage by R135 and the op amp. Q103 bootstraps out the summing junction capacitanc e of Q102.

Notch Filters

U107 is a high Q, line frequency, notch filter which can be switched in and out by analog switch 1/4 U106. The frequency and depth of the filter can be adjusted with P102 and P103. Resistors R146-R149 and switch U108 make up a selectable attenuator. U118 is a line frequency 2nd harmonic notch filter selected by 2/4 U106. P104 and P105 adjust the frequency and depth. The second notch filter has a gain of 3 and its output is scaled by U110 and resistors R156-R159. The signal then takes two paths; to inverting amplifier U111 and to the input of the tracking bandpass filter. U111 has the same gain as the bandpass filter. The output of either U111 or the bandpass filter is selected by 3/4 U112 and 4/4 U106 and amplified by U113. U114 and U115 provide a last stage of gain and scaling and the final output is ac coupled and buffered by 4/4 U208.

Bandpass Filter

The bandpass filter is a three op amp statevariable active filter. 3/4 of U201 make up the three op amps of the standard filter. U203,

U204, and U205 are analog switches which select the feedback capacitors for the 5 decades of operation. The two halves of U202 are matched transconductance amplifiers operating as programmable, voltage controlled, current sources which take the place of the normal, frequency setting, resistors. A voltage proportional to the reference frequency is converted into a current by 1/4 U208 and Q201. This current programs the effective "resistance" of the two transconductance amplifiers and thus, tunes the center frequency of the filter to follow the reference. The output of the filter is buffered by 4/4 U201. The two remaining op amps in U208 are used to detect signal overloads throughout the amplifier chain.

Reference Oscillator

The reference input signal is ac coupled and buffered by U301. R378 isolates the reference shield from the lock-in ground to prevent ground loop currents. 1/2 U303 switches the polarity of the reference reaching comparator U304. U305 is a retriggerable one-shot whose out put ind ic ates a no reference condition if no comparator pulses are generated for three seconds.

U309 is a dual transconductance amplifier in a triangle VCO configuration. U310 selects the integrating capacitor depending on the frequency range. The VCO frequency is determined by the programming current through R318 and therefore by the output voltage of U308. C306 is the phaselocked loop low pass filter which is buffered by U308. U307 is a programmable current source used to charge and discharge C306. The amount of current available to U307 is determined by the VCO control voltage, thus, the tracking rate of the VCO is proportional to the VCO frequency. The triangle output is compared to a constant voltage by U314. 1/2 U313 and 1/2 U312 select f or 2f operation. This signal is fed back to the phase detector U306 to be compared with the reference output of U304. U315 compares the triangle output with a variable voltage to generate a square-wave signal phase-shifted from the reference. The range of this fine phase shift control is -5 to 95 degrees.

The output of U315 serves as the reference to a second phase-locked loop. This second PLL uses a similar proportional tracking triangle VCO. Comparator U329 looks at the square wave output of the VCO while comparator U328 detects the zero crossings of the triangle output. 1/2 U327 selects one these comparators to feed back to the phase detector, U316. Since the square and triangle outputs are in quadrature, U327 selects either an in-

phase or quadrature relationship between the two VCO's. Thus, the output of the second VCO can be shifted from -5 to 185 deg from the reference.

The triangle output is divided by R363 and R362 before reaching transconductance amplifier 2/2 U322. The amplitude of the triangle input to this amplifier is enough to just saturate the input and provide a sine wave output. 2/2 U325 then amplifies the sine wave before it goes to the demodulator. U324 is a comparator which generates a square wave in-phase with the sine output. U326 divides the frequency of the square wave by eight and 2/2 U327 selects the frequency of the square wave chopper.

The square wave output of U322 serves as the reference to the quadrature oscillator PLL. This PLL is identical to the triangle oscillator, sine wave shaper described above. U1004 detects the zero-crossings of the triangle wave to feed back to the phase comparator, U1002. This ensures that the quadrature triangle wave is 90 deg out of phase from the first sine wave. The quadrature triangle is shaped into a sine wave by 2/2 U1009 and amplified by 2/2 U1014. U1012 is a comparator which generates a square wave in-phase with the quadrature sine wave. U1013 divides the frequency of the square wave by eight and 1/2 U1011 selects the frequency of the square wave chopper.

Demodulator and Low Pass Amplifier

Amplifier U402 and switch U401 select the polarity of the reference sine wave. This allows phase shifts up to 360 degrees from the reference input. The sine wave is ac coupled by U403 and inverted by U404. U405 selects alternating polarities of the sine wave at the chopper frequency, f/2 or f/16. This chopped sine wave is then multiplied by the output of the signal amplifiers by the analog multiplier U406. The synchronous output of the multiplier that corresponds to the in-phase signal is a square wave at the chopper frequency. The output is ac coupled by U407 to remove the dc offset of the multiplier. U408 inverts the signal and U405 chops the square wave to recover a dc output. U409 buffers the chopper output before the first low pass time constant. Op amps U416 and 2/2 U402 make up the first low pass amplifier with relays U411-U415 and U417 selecting the time constant. The second low pass amplifier is

U419. Analog switch U418 selects the time constant and gain. The full scale output of U418 is 5 volts.

The quadrature demodulator and low pass amplifiers are identical to that described above. The quadrature detector output is provi ded by U1119.

Analog Output and Control

The dc output of the demodulator/low pass amplifiers is passed to the reference input of multiplying DAC U502. The DAC is programmed with the appropriate attenuation to calibrate the overall gain of the lock-in. Every gain setting in each dynamic reserve is calibrated independently and the proper attenuations are stored in the unit's ROM.

used to program the band pass filter and the reference oscillator phase sh ift. One output is subtracted from the lock-in output in U508 to provide a variable offset and another is the rms noise output. The remaining two outputs generate the magnitude and phase output voltages.

Expand

3/4 U511 and 4/4 U1202 are the expand amplifiers. They provide a selectable gain of 10 to the channel 1 and 2 outputs just before the output buffers.

Front Panel

The quadrature output is calibrated by DAC U1201. Amplifiers U1204 and U1205 buffer the two demodulator outputs to drive the X and Y BNC's.

A/D's

Analog multiplexer U504 selects the signal to be digitized by the microprocessor. This signal can be either the lock-in's in-phase or quadrature output or one of the four independent analog inputs buffered by U501. These general purpose inputs are located on the rear panel of the instrument. The selected signal is sampled and held on capacitor C502 and buffered by 4/4 U508. The A/D conversion is done by successive approximation using comparator U514 to compare the sampled and held signal with known outputs of U505, a 12 bit DAC with a precision reference. Note that the output of U506, an 8 bit DAC is summed with the output of U505. This 8 bit DAC corrects for offset errors which can accumulate as analog voltages pass through buffers, S/H amps, and comparators. These offsets are measured after each unit is manufactured, and values to compensate for these offsets are placed in the unit's ROM. The polarity of the offset-corrected 12 bit DAC is set by 2/4 U511 and the SIGN bit yielding 13 bits of resolution from -10.24 to +10.24 volts.

D/A's

In addition to providing reference voltages for A/D conversion, the DAC output voltage may be multiplexed by U507 to one of eight sample and hold amplifiers which provide analog output and control voltages. The microprocessor refreshes each S/H amplifier every few milliseconds to prevent droop. Two of these outputs are available as general programmable outputs on the rear panel. Two are

There are 71 led's on the front panel controlled by 9 serial-in, parallel-out shift registers. 8 of the shift registers are written to simultaneously and the 9th is written separately. 8 consecutive write operations are required to set the LED's in each case. The liquid crystal displays are managed by the display controllers, U6101, U6102, and U6103. Exclusive-or gates U6104, U6105 and U6106 drive the left over segments. Latches U6107 and U6108 provide the logic bits for these extra segments as well as the keyboard row strobes. U6109 reads the switch closures as the rows are scanned.

Microprocessor Control

The microprocessor, U701, is a Z80A CPU clocked at 4 MHz. 16K bytes of firmware are stored in the ROM, U702. U703 is a 2K byte static RAM, backed-up by a lithium battery. A power-down standby circuit, Q701, preserves the RAM contents when the power is turned off. The battery has a life of 5-10 years. The CPU has power-up and power-down resets to prevent erroneous execution during turn-on or short sags in the line voltage.

U704 is a 3-channel counter. One channel generates the baud rate for the RS232 interface while the other two are used to measure the frequency or period of the reference oscillator. U709 provides a gate pulse to counter 0. Multiplexer U708 selects whether the gate is a single period of the reference (period measurement) or a gate of known duration (frequency measurement). Counter 1 is a programmable divide by N counter whose output is either counted for one period of the reference,

or, generates the gate pulse during which reference pulses are counted.

I/O addresses are decoded by U705, U706, and U707. The microprocessor controls the lock-in functions through I/O ports U714-U721. U713 generates an interrupt to the CPU every 4 msec to keep the microprocessor executing in real time.

RS232 Interface

The RS232 interface uses an 8251A UART, U801, to send and receive bytes in a bit serial fashion. Any standard baud rate from 300 to 19.2K baud may be selected with the configuration switches. The X16 transmit and receive clock comes from counter 2 of U704. The RS232 interface is configured as DCE so that a terminal may be connected with a standard cable. When a data byte is received by the UART, the RxRDY output interrupts the CPU to prevent the data from being overwritten.

GPIB Interface

The interface to the GPIB is provided by U802, an MC68488 General Purpose Interf ace Ada pter (GPIA). The GPIB data and control lines are buffered by drivers U808 and U811. Because the GPIA uses a 1 MHz clock, wait states are provided by U805 to synchronize I/O transactions with the 4 MHz CPU. The GPIA interrupts the CPU whenever a GPIB transaction occurs which requires the CPU’s response. (The GPIB address is set by switch bank SW1.)

Internal Oscillator

The internal oscillator is on a small circuit board attached to the rear panel of the instrument. Local regulators, Q1 and Q2, provide power to the board. The VCO input is internally pul led up by R12. This pulls the VCO input to 10V when the VCO input is left open. 2/4 U1 translates the VCO input voltage to provide a negative control voltage to U2, the function generator. P3 adjusts the VCO calibration. U2 is a sine wave generator whose frequency range is selected by the VCO Range switch and capacitors, C4-C6. P2 adjusts the sine wave symmetry at low frequencies. 4/4 U1 buffers the output of U2. P1 adjusts the amplitude of the output sine wave. The output amplitude on the SIne Out is selected by the amplitude switch. The output impedance is 600 Ω.

Power Supplies

The line transformer provides two outputs, 40VAC and 15VAC, both center tapped. The transformer has dual primaries which may be selected by the voltage selector card in the fuse holder. The 15VAC is rectified by diode bridge BR2 and passed to 5V regulator U909. The output of U909 powers the microprocessor and its related circuitry. The 40VAC output is half-wave rectified by BR1 and regulated by U901 and U902 to provide +20V and -20V. These two dc voltages are then regulated again by 15V regulators U903-U908. Each 15V regulator powers a separate section of the lock-in to reduce coherent pick up between sections. U911 and U912 provide plus and minus 7.5V and U910 generates +5V for the analog circuits.

Calibration and Repair

This section details calibration of the instrument. Calibration should be done only by a qualified electronics technician.

********* WARNING *********

The calibration procedure requires adjusting the instrument with power applied and so there is a risk of personal injury or death by electric shock. Please be careful.

Most of the calibration parameters are determined by a computer aided calibration procedure after burn-in at the factory. These calibration parameters are quite stable and so will not need to be adjusted. Calibration parameters which may need field adjustment are detailed below.

Multiplier Adjustments

On the HIGH dynamic reserve setting, there can be some reference frequency feedthrough. This section describes how to null this unwanted output.

This adjustment requires an oscilloscope and a signal generator which can provide a 500Hz reference signal.

Allow the unit to warm up for about 1 hour. Reset the unit by turning it off and back on while

holding the LOCAL key down. Select voltage input A and connect a 50 1/2

terminator or shorting plug to the A input BNC connector. Connect the 500 Hz reference signal to the reference input. Set the SENSITIVITY to

1mV and the DYN RES to HIGH. The PRE TIME CONSTANT should be set to 1mS and the POST TIME CONSTANT to NONE.

Connect the scope to the CHANNEL 1 OUTPUT on the front panel. Set the scope to 2V/div and 5mS/div. Externally trigger the scope using the reference input signal.

After about 90 seconds, the scope display should show a 500 Hz sine wave on a 30 Hz (500/16 Hz) square wave. Remove the four screws holding the top panel on. Slide the top panel back about half way. Using a small screwdriver, adjust P402 at location D2 to

minimize the 500 Hz output. Adjust P403 at location C2 to minimize the 30 Hz output.

Now set the both time constants to 1S. Adjust P404 at location F4 to zero the output. This adjustment has a range of 20% of full scale on the HIGH dynamic reserve setting. (2% on NORM and 0.2% on LOW). This zeroes the DC output of Channel 1 on all dynamic reserve ranges.

Now connect the scope to the CHANNEL 2 OUTPUT. Set the PRE TIME CONSTANT to 1mS and the POST TIME CONSTANT to NONE. Adjust P1102 to minimize the 500 Hz output. Adjust P1103 to minimize the 30 Hz output. Set both time constants to 1S. Adjust P1104 to zero the output. All three potentiometers are located on the plug-in board in the center of the main circuit board.

Replace the top panel.

Amplifier and Filter Adjustments

This section describes how to adjust the Common Mode Rejection and Line notch filter frequencies. An oscilloscope and a signal generator which can provide an accurate line frequency and twice line frequency sine wave are required.

Allow the unit to warm up for about 1 hour. Reset the unit by turning it off and back on while

holding the LOCAL key down. Remove the four screws holding down the top panel.

Slide the panel back about halfway.

CMRR

Set the reference frequency to 100 Hz. It is convenient to use the SYNC output of the signal generator as the reference input if it is available. Connect the sine output of the signal generator to the A input and set the input selector to A. With the SENSITIVITY at 100mV, adjust the amplitude of the input signal to 100 mV (full scale).

Now set the input selector to A-B and connect the signal to both the A and B inputs. Set the SENSITIVITY to 20µV, the DYN RES to NORM and the BANDPASS filter IN. Connect the scope to the SIGNAL MONITOR output on the rear panel. Set the scope to AC coupled, 0.2V/div, and 10mS/div. Externally trigger the scope using the reference input signal.

The CMRR is adjusted by the single turn potentiometer located at A1 under the single hole at the front of the signal shield. (The shield is the aluminum box on the left side of the main board). Using a small screwdriver, carefully adjust the potentiometer to minimize the 100 Hz output on the scope. Set the DISPLAY to R,Ø and the sensitivity to 5µV and minimize the R output on the Channel 1 meter.

Notch Filters

Set the reference frequency to 60.0 Hz (50.0 Hz). It is convenient to use the SYNC output of the signal generator as the reference input if it is available. Connect the sine output of the signal generator to the A input and set the input selector to A. With the SENSITIVITY at 100mV, adjust the amplitude of the input signal to 100 mV (full scale).

Set the LINE NOTCH to IN, the SENSITIVITY to 10mV, and the DYN RES to LOW. Connect the scope to the SIGNAL MONITOR output on the rear panel. Set the scope to AC coupled,

0.2V/div, 10mS/div. Trigger the scope externally using the reference input signal.

The LINE NOTCH frequency and depth are adjusted by the pair of 20 turn potentiometers located under the middle two holes in the signal shield (row 4 on the circuit board). Using a small screwdriver, carefully adjust one pot until the line output on the scope is minimized. Then adjust the other pot until the output is minimized. Iterate between the two pots until there is no further improvement. Set the SENSITIVITY to 5mV, 2mV, and 1mV, repeating the adjustments at each sensitivity.

Repeat this procedure using a reference frequency of 120.0 Hz (100.0 Hz) and the LINEX2 NOTCH filter. The LINEX2 NOTCH is adjusted by the pair of 20 turn potentiometers located under the back two holes in the signal shield (row 5 on the circuit board). Replace the top panel.

Replacing the Front-End Transistors

Both the voltage and current front end transistors (Q101 and Q102) are 2N6485 (IMF6485) dual JFETS. These transistors are selected at the factory to meet the noise specifications.

This section outlines their replacement procedure in the event that they become damaged during use.

1) Remove the AC power cord from the unit.

2) Remove top and bottom panels.

3) Release the signal shields by removing the four screws which hold it onto the circuit board. Be careful not to lose the nuts. Carefully slide the shields back and then lift them out.

4) The input transistors are located on the main board, just behind the input selector switch. Q101 is the voltage (A, A-B) front end, and Q102 is the current (I) front end. Desolder and replace the appropriate transistor.

5) Replace the signal shields. Be careful to check that the shields do not touch any circuit board traces around their edges.

6) Replace the top and bottom panels.

7) If Q101, the voltage front end has just been replaced, the Common Mode Rejection needs to be readjusted using the procedure described in the Amplifier Adjustments section.

Appendix A: Noise Sources and Cures

And Others. Other noise sources include flicker

noise found in vacuum tubes, and generati on and recombination noise found in semiconductors.

Noise, random and uncorrelated fluc tuat ions of electronic signals, finds its way into experiments in a variety of ways. Good laboratory practice can reduce noise sources to a manageable level, and the lock-in technique can be used to recover signals which may still be buried in noise. Intrinsic Noise Sources

Johnson Noise. Arising from fluctuations of electron density in a resistor at finite temperature, these fluctuations give rise to a mean square noise voltage,

_ V2 = ∫4kT Re[Z(f)] df = 4kTR ∆f

where k=Boltzman's constant, 1.38x10-23J/°K; T is the absolute temperature in Kelvin; the real part of the impedance, Re[z(f)] is the resistance R; and we are looking at the noise source with a detector, or ac voltmeter, with a bandwidth of ∆f in Hz. For a 1MΩ resistor,

1/2

(V2)

= 0.13 µV/√Hz

All of these noise sources are incoherent. Thus, the total noise is the square root of the sum of the squares of all the incoherent noise sources.

Non-Essential Noise Sources

In addition to the "intrinsic" noise sources listed above there are a variety of "non-essential" noise sources, i.e. those noise sources which can be minimized with good laboratory practice. It is worthwhile to look at what might be a typical noise spectrum encountered in the laboratory environment:

To obtain the rms noise voltage that you would see across this 1M½ resistor, we multiply

0.13µV/√Hz by the square root of the detector bandwidth. If, for example, we were looking at all frequencies between dc and 1 MHz, we would expect to see an rms Johnson noise of _

1/2

(V2) '1/f Noise'. Arising from resistance fluctuations

in a current carrying resistor, the mean squared noise voltage due to '1/f' noise is given by

where A is a dimensionless constant, 10 carbon, R is the resistance, I the current, ∆f the bandwidth of our detector, and f is the frequency to which the detector is tuned. For a carbon resistor carrying 10 mA with R = 1k, ∆f = f = 1Hz, we have

= 0.13 µV/√Hz*(106 Hz)

_ V2 = A R2 I2 ∆f/f

noise

= 3 µVrms

1/2

= 130 µV

-11

for

Noise Spectrum

Some of the non-essential noise sources appear in this spectrum as spikes on the intrinsic background. There are several ways which these noise sources work their way into an experiment.

Capacitive Coupling. A voltage on a nearby piece of apparatus (or operator) can couple to a detector via a stray capacitance. Although C

may be very small, the coupled in noise

stray may still be larger than a weak experimental signal.

Inductive Coupling. Here noise couples to the experiment via a magnetic field:

Inductive Noise Coupling

Capacitive Noise Coupling

To estimate the noise current through C

stray

into

the detector we have

i=C

stray

dV = jwC

strayVnoise

where a reasonable approximation to C

stray

can

be made by treating it as parallel plate capacitor. Here, w is the radian frequency of the noise source (perhaps 2 * π * 60Hz ), V

noise

is the

noise voltage source amplitude (perhaps 120 VAC). For an area of A = (.01 m)2 and a distance of d = 0.1m, the 'capacitor' will have a value of 0.009 pF and the resulting noise current will be 400pA. This meager current is about 4000 times larger than the most sensitive current scale that is available on the SR510 lock-in.

Cures for capacitive coupling of noise signals include:

A changing current in a nearby circuit gives rise to a changing magnetic field which induces an emf in the loop connecting the detector to the experiment.

(emf = dØ

/dt.) This is like a transformer, with the

experiment-detector loop as the secondary winding.) Cures for inductively coupled noise include:

1) removing or turning off the interfering noise source (difficult to do if the noise is a broadcast station),

2) reduce the area of the pick-up loop by using twisted pairs or coaxial cables, or even twisting the 2 coaxial cables used in differential hook-ups,

3) using magnetic shielding to prevent the magnetic field from inducing an emf (at high frequencies a simple metal enclosure is adequate),

4) measuring currents, not voltages, from high impedance experiments.

1) removing or turning off the interfering noise source,

2) measuring voltages with low impedance sources and measuring currents with high impedance sources to reduce the effect of i

stray

3) installing capacitive shielding by placing both the experiment and the detector in a metal box.

Resistive Coupling (or 'Ground Loops'). Currents through common connections can give rise to noise voltages.

Microphonics provides a path for mechanical noise to appear as electrical noise in a circuit or experiment. Consider the simple circuit below:

The capacitance of a coaxial cable is a function of its geometry so mechanical vibrations will cause the cable capacitance to vary with time. Since C=Q/V, we have

Resistive Coupling Here, the detector is measuring the voltage

across the experiment, plus the voltage due to the noise current passing through the finite resistance of the ground bus. This problem arises because we have used two different grounding points which are not at exactly the same potential. Some cures for ground loop problems include:

1) grounding everything to the same physical point,

2) using a heavier ground bus to reduce the potential drop along the ground bus,

3) removing sources of large currents from ground wires used for small signals.

C dV + V dC dt dt dt

so mechanical vibrations will cause a dC/dt which in turn gives rise to a current i, which will affect the detector. Ways to eliminate microphonic signals include:

1) eliminate mechanical vibrations,

2) tie down experimental cables so they will not sway to and fro,

3) use a low noise cable that is designed to reduce microphonic effects.

Thermocouple Effect. The emf created by dissimilar metal junctions can give rise to many microvolts of dc potential, and can be a source of ac noise if the temperature of the junction is not held constant. This effect is large on the scale of many low level measurements.

= dQ = i

Appendix B: Introduction to the RS232

The 'RS232' is a standard for bit serial asynchronous data communication. The standard defines the format for data transmission, the electrical specifications for the signal levels, and the mechanical dimensions of connectors.

Despite the definition of a standard, there are so many permutations of control lines, data formats, and transmission speeds, that gett in g two RS232 devices to communicate usually requires some work.

In this section, we will provide some basic information to aid you in connecting your RS232 device to the SR530 Computer Interface.

CASE 1 - The Simplest Configuration.

data, must also be connected correctly at the terminal end. If the terminal responds to a control line, it will believe that the SR530 is not ready to accept data (because the line is not passed in this example) and will therefore not send any data.

CASE 2 - RS232 with Control Lines.

The data lines are the same as in Case 1. In addition to the data lines, there are two control lines used:

CTS - Pin 5 "Clear to send" is a signal asserted by the DCE to tell the DTE that the DCE is ready to receive data.

DTR - Pin 20 "Data Terminal Ready" is a signal asserted by the DTE to tell the DCE that the DTE is ready to receive data.

In this case, one wire is used to send data from device A to device B and another wire is used to send data from device B to device A. Notice that pin 2 is an output on device A and an input on device B. (It is good practice to run the ground, pin 7, between the devices as well). The RS232 defines two types of devices; DTE (Data Terminal Equipment) and DCE (Data Communications Equipment.) An RS232 por t on a computer may be either a DTE or DCE but nearly every terminal with an RS232 port is a DTE. RS232 ports on a computer which are intended to connect to a modem, such as the COM1: port on the IBM PC, are DTE. The SR530 is configured as DCE, and so it may be directly connected to ASCII terminals and to the COM: ports on IBM PC's and compatibles.

As an example, consider connecting an RS232 ASCII computer terminal to the SR530 using a 2 wire link. The terminal is a DTE and the SR530 is a DCE. To operate correctly, the SR530 and the terminal must have the same settings for baud rate, parity, and number of stop bits. The control lines in the RS232 Standard, which are used to indicate that a device is ready to accept

The SR530 responds to the control lines as follows:

1) If the lines are not connected, the SR530 assumes that you are ready to receive data.

2) Data will not be transmitted from the SR530 if the

DTR line (pin 20) is low. This is useful in the case when your program is not yet ready to receive data. If data transmission is not suspended, then data may be overwritten in your computer's UART (as it is not being retrieved by the program and so will be lost.) When this happens, the 'over-run' flag will be set in your computer's UART and it may be recognized by the operating system, generating an error message such as "I/O Device Error" (See the "W" command in the SR530 Command List for another way to slow data transmission.)

Baud Rate

The RS232 baud rate of the SR530 is switch selectable from 300 to 19.2K baud (see configuration switch setting in the front of this manual.) 19.2K baud means that data is transmitted at 19,200 bits/second. With one start bit, 2 stop bits, 8 data bits, and no parity bits, each ASCII character requires 573 µsec to be transmitted (11bits/19.2K

baud.) The typical data string 5.1270<cr> characters, requiring 4 msec to be sent.

has 7

Stop Bits

Generally, selection of 2 stop bits will result in fewer data transmission errors.

Parity

The Parity bit provides a check against faulty data transfer. It is not commonly used in local data transmission environments. If the parity option is selected, the SR530 will transmit 8 data bits and a parity bit, however, no parity check of incoming data is done.

Voltage Levels

The RS232 uses bipolar voltage levels:

The control lines use positive logic. For example, the DCE tells the DTE that it is clear to send (CTS) by placing > +3 VDC on pin 5 of the interface. Similarly, the DTE can tell the DCE that it is not ready by placing -3 VDC on pin 20 (DTR) of the interface.

The data lines, pins 2 and 3, use negative logic. A 'zero' bit is represented by a positive voltage and a 'one' bit is represented by a negative voltage. A start bit is a positive voltage and a stop bit is a negative voltage. Data is transmitted with the least significant bit first. The

letter 'A', which has the ASCII code 41H (0100

0001), would appear as follows: If a parity option was selected, the parity bit would be sent after the 8th data bit, but before the first stop bit.

Final Tip

When you are trying to get the RS232 to work with your computer, it is helpful to be able to 'eavesdrop' on the RS232 data lines going between the SR530 and the computer. This can be done with an ASCII RS232 terminal and the following connector:

To test the connector, place the hook clip on pin 2 of the same connector (shorting pin 2 to pin 3.) Now, when you type at the terminal keyboard, data transmitted from pin 2 is received at pin 3 and displayed on the terminal screen. To use as a debugging tool, attach the hook clip to either pin 2 or pin 3 of the RS232 cable on the SR530 to show either data sent from the Computer or the SR530. The baud rate, parity, and stop bits of the terminal must match those of the SR530 and the computer. If your terminal has a mode which will display control characters (such as carriage returns and line feeds) it is helpful to operate in that mode.

A variant of the 'eavesdropping' approach is

diagrammed below: With this cable arrangement, the ASCII terminal can

listen to the data passing in both directions. The only drawback is that the terminal will display garbled data if both devices transmit data at the same time.

Appendix C: Introduction to the GPIB

Data Bus: There are eight data lines which use

negative logic and pass the bits of each byte in parallel.

The IEEE-488 Standard specifies the voltage levels, handshake requirements, timing, hardware details, pinout and connector dimensions for a 16 line, bit parallel bus . Many instruments may be connected in series to communicate over the same cable. Because the bits are passed in parallel, the GPIB is faster than the RS232.

The controller (generally your computer) coordinates data transfer on the bus by designating all participating instruments (including itself) as either a talker or a listener. Listeners can receive data placed on the bus by the Talker. Devices can have the capacity to operate in either mode. The address of each device is set by switches in the device and must be between 0 and 30.

Bus Description

Byte Transfer Control Group. This consists of

3 negative logic lines that implement the GPIB handshaking. The NRFD (Not Ready For Data) line is held low by any designated listener who is not ready to accept data. When every listener is ready, the line goes high and the talker may release data to the bus. After data is on the bus, the talker pulls the DAV (Data Valid) line down. At this point, each listener retrieves the data. Before and during the retrieval of the data, the listener holds the NDAC (No Data Accepted) line down. When every listener has received the data, the NDAC line goes high, allowing the talker to release the DAV line high. Finally, the listener pulls down the NDAC line until another transfer is initiated.

General Interface Lines: These five lines operate independently of the handshake lines and use negative logic.

1) The EOI (End or Identify) line is used by the talker

to designate the end of message.

2) The SRQ (Service Request) line is used by any

device to ask for service. The controller can serial poll each device (each device returns an 8 bit status byte) to determine who needs attention. It can also do a parallel poll using the EOI and ATN lines where each device is assigned a single data line.

3) The ATN (Attention) line makes both talkers and

listeners accept information and passes control of the DAV line to the controller. This line is used by the controller to identify talkers and listeners through their addresses.

4) The REN (Remote Enable) line changes the

status of an instrument from local to remote.

5) The IFC (Interface Clear) line clears the bus of all

data and activity. Though GPIB is a very powerful interface, strict

protocol must be observed for it to operate successfully.

Appendix D: Program Examples

All of the program examples which follow do the same thing, only the computer, language, or interface is changed. The programs read the Channel 1 and 2 Outputs and write the results to the computer screen. In addition, the X6 analog output port is ramped from 0 to 10V.

Program Example 1: IBM PC, Basic, via RS232

In this example, the IBM PC's ASYNC port (known as COM1: or AUX: to DOS users) will be used to communicate with the SR530. Only two wires between the IBM PC's ASYNC port and the SR530 are needed (pins #2 & #3 of the RS232), but pins 5,6,8 and 20 should be connected together on the connector at the IBM end.

10 ′ EXAMPLE PROGRAM TO READ THE SR510 OUTPUT AND RAMP THE X6 ANALOG OUTPUT 20 ′ USING IBM PC BASICA AND THE COM1: RS232 PORT. 30 ′ THE RAMP ON X6 CAN BE WATCHED BY SETTING THE SR530 DISPLAY TO A/D. 40 ′ 50 ′ 60 ′ ON THE REAR PANEL OF THE SR530, SET SWITCH #1 OF SW2 DOWN 70 ′ AND ALL OTHER SWITCHES IN SW2 UP. (9600 BAUD, NO PARITY) 80 ′ 90 OPEN ″COM1:9600,N,8,2,CS,DS,CD″ AS #1 100 ′ SET UP COM1: PORT TO 9600 BAUD, NO PARITY, 8 DATA BITS, 2 STOP BITS, 110 ′ IGNORE CTS (CLEAR TO SEND), DSR (DATA SET READY), 120 ′ AND CD (CARRIER DETECT). 130 ′ 140 PRINT #1, ″ ″ ‘CLEAR UART BY SENDING SPACES 150 PRINT #1, ″Z″′RESET SR530 160 FOR I = 1 TO 200: NEXT I ′WAIT FOR RESET TO FINISH 170 ′ 180 X = 0 ′INIT X6 OUTPUT TO ZERO 190 ′ 200 PRINT #1, ″Q1″ ′READ OUTPUT 210 INPUT #1,V1 ′INTO V1 220 PRINT #1, ″Q2″′READ OUTPUT 230 INPUT #1,V2 ′INTO V2 240 ′ 250 PRINT ″CH1 = ″;V1;″ CH2 = ″;V2 260 ′ 270 X =X + .0025 ′INCREMENT X6 OUTPUT BY 2.5 MV 280 IF X > 10 THEN X = 0 ′RESET X6 RAMP 290 PRINT #1, USING ″X6, ##.###″;X ′SET X6 OUTPUT VOLTAGE 300 ′ 310 GOTO 200 ′LOOP FOREVER

Program Example 2: IBM PC, Microsoft Fortran v3.3, via RS232

Machine language routines to interface to the COM1: RS232 port are provided in the file RS232.OBJ found on the SR575 disk. These routines allow for simple interfacing to the SR530 at 19.2 kbaud from FORTRAN programs.

$storage:2 $include: ′for232.inc′ [ for 232.inc must be included to call subroutines in RS232.OBJ [ link with RS232.OBJ (on SR565 disk) [ RS232.OBJ defines: [ init [ initializes COM1: to 19.2 kbaud [ txstr (str) str is a string terminated with ′$′ [ transmits str to COM1: [ rxstr (str) str must be declared with length of 15 or greater [ fills str with string received from COM1: [ if and error occurs, nocom is called. [ Nocom should be a FORTRAN subroutine in your program.

To use these routines, the file 'for232.inc' (also on the SR575 disk) must be 'included' in the FORTRAN source.

Only two wires between the IBM PC's ASYNC port and the SR530 are needed (pins #2 & #3 of the RS232), but pins 5,6,8 and 20 should be connected together on the connector at the IBM end.

program ex2

character *20 str1,str2, str3

[ Example program to read the SR530 outputs and ramp the [ X6 analog output using Microsoft FORTRAN v3.3 and the [ COM1: port. Set all switches in SW2 to UP on SR530 [ for 19.2 kbaud.

[ The ramp on X6 can be watched by setting the SR530 [ display to D/A/

[ initialize COM1: port to 19.2 kbaud

call init

[ set character wait interval to zero

call txstr(′w0$′)

[ reset X6 to zero

x6=0.0

[ read channel 1 output into string variable str1 20 call txstr(′q1$′)

call rxstr(str1)

[ read channel 2 output into string variable str2

call txstr(′q2$′)

call rxstr(str2)

[ convert string variable into real variable v1 and v2

read (str1,1000) v1 read (str2,1000) v2

1000 format (bn,f10.0)

[ print results to screen

write(*,2000) v1, v2

2000 format(′ Channel 1=′,G10.3,3x, ′Channel 2=′,G10.3)

[ ramp x6 by 2.5 mV

x6 = x6 + .0025 if (x6.gt.10) x6 = 0.0

[ make x6 command string

write (str3,3000) x6

3000 format (′x6,′,f7.3,′$′)

call txstr(str3)

[ and loop forever

goto 20

stop end

[ ***********************************

subroutine nocom

[ in case of a timeout error, this routine runs [ put your error handler here.

[ write(*,*) char (7)

write(*,*)′RS232 Timeout Error! ′

stop end

Program Example 3: IBM PC, Microsoft C v3.0, via RS232

#include <stdio.h>

/* Compile with >MSC program name/AL;

link with RS232.OBJ (on SR565 disk)

RS232.OBJ defines: init ()

Initializes COM1: to 19.2 kbaud

txstr (str);

Char *str; str must terminate with ′$′ char

Sends string str to COM1:

rxstr (str); str must be declared with 15 characters

or more length. Fills str with string received from COM1:

To use these routines, the large model must be used. Compile with the /AL switch and link with RS232.OBJ.

Only two wires between the IBM PC's ASYNC port and the SR530 are needed (pins #2 & #3 of the RS232), but pins 5,6,8 and 20 should be connected together on the connector at the IBM end.

main ()

If an error occurs, your procedure nocom() is called. Nocom() must be a C procedure in your program.

Example program to read the SR510 outputs and ramp the x6 analog Output using Microsoft C v3.0 (large model) and the COM1: port. Set all switches in SW2 to UP on SR530 for 19.2 kbaud.

The ramp on x6 can be watched by setting the SR530 display to D/A.

{ char str1[20], str2[20], STR3[20]; float v1,V2,x;

init (); /* init COM1: port to 19.2 kbaud */ txstr (″w0$″); /* set character interval to 0 */

x = 0; while (1)

{ txstr (″q1$″); /* read channel 1 output */ rxstr (str1); /* into str1 */ sscanf (str1, ″%f″, &v1); /* scan str1 for a float variable */

txstr (″q2$″); /* read channel 2 output */ rxstr (str2); /* into str2 */ sscanf (str2, ″%f″, &v2); /* scan str2 for a float variable */

x += 0.0025; /* increment x6 output by 2.5 mV */ if (x >= 10) x = 0; sprintf (str3, ″X6,%f$″, x); /* make x6 command string */ txstr (str3); /* send x6 command */

/* print results to screen */ printf (″Channel 1 = %10.36 Channel 2 = %10.36\n″, v1, v2); }

} /* ********************************************* */ nocom ()

/* error handling routine goes here */

{

printf(″RS232 Timeout Error\n″);

putch (7);

exit ();

}

Program Example 4: IBM PC,Microsoft Basic, via GPIB

This program requires the Capital Equipment Corporation GPIB card for the IBM PC or XT. It has firmware in ROM to interface high level languages to the GPIB.

Subroutine calls in Microsoft BASIC are done to memory locations specified by the name of the subroutine. The address is relative to the segment address specified by the DEF SEG statement preceding CALL.

10 ′ EXAMPLE PROGRAM TO READ THE SR530 OUTPUT AND RAMP THE X6 ANALOG OUTPUT 20 ′ USING IBM PC BASICA AND THE CAPITAL EQUIPMENT CORP. GPIB INTERFACE CARD 30 ′ 40 ′ THE RAMP ON X6 CAN BE MATCHED BY SETTING THE SR530 DISPLAY TO D/A. 50 ′ 60 ′ ON THE SR530 REAR PANEL, SET SWITCHES #4 AND #6 ON SW1 TO DOWN (DEVICE 70 ′ ADDRESS = 23, RS232 ECHO ON) AND SWITCH # 1 ON SW2 TO DOWN (RS232 BAUD 80 ′ RATE = 9600). ALL OTHER SWITCHES SHOULD BE UP. 90 ′ NOTE THAT THE RS232 ECHO IS FOR DEBUGGING AND DEMOSTRATION PURPOSES, 100 ′ UNDER NORMAL CONDITIONING, SWITCH # 6 OF SW1 SHOULD BE UP SINCE THE RS232 110 ′ ECHO SLOWS DOWN THE GPIB INTERFACE. 120 ′ 130 DEF SEG = &HC000 ′BASE ADDRESS OF CEC CARD 140 INIT=0: TRANSMIT=3: RECV=6: ′ADDRESSES OF CEC FIRM WARE ROUTINES 150 ADDR%=21: SYS%=0 ′CONTROLLER ADDRESS 160 INZ$ = ″IFC UNT UNL MTA LISTEN 23 DATA ′Z′ 13″ 170 ′ 180 Q1$ = ″IFC MTA LISTEN 23 DATA ′Q1′ 13″ 190 Q2$ = ″IFC MTA LISTEN 23 DATA ′Q2′ 13″ 200 X6$ = ″IFC MTA LISTEN 23 DATA ′X6, ″ 210 LISN$ = ″IFC UNT UNL MLA TALK 23″ 220 ′ 230 ′ 240 CALL INIT(ADDR%,SYS%) ′INIT X6 OUTPUT TO ZERO 250 CALL TRANSMIT(INZ$,STATUS%) ′RESET SR530 260 GOSUB 600 ′CHECK TRANSMIT STATUS 270 ′ 280 X = 0 ′INIT X6 OUTPUT TO ZERO 290 ′ 300 CALL TRANSMIT(Q1$,STATUS%) ′READ CHANNEL 1 OUTPUT 310 GOSUB 600 320 GOSUB 510 ′GET RESULT 330 V1 = VAL(ANS$) ′INTO V1 340 ′ 350 CALL TRANSMIT(Q2$,STATUS%) ′READ CHANNEL 2 OUTPUT 360 GOSUB 600 370 GOSUB 510 ′GET RESULT 380 V1 = VAL(ANS$) ′INTO V2

In this program, the CEC card's ROM starts at OC0000H, the system controller's address is 21, and the SR530 has been assigned as GPIB address 23.

To monitor the GPIB activity with an RS232 terminal, SW1-6 should be down, and the ASCII terminal should be attached to the rear panel RS232 connector.

390 ′ 400 PRINT “CH1 = ″;V1; ″ CH2 =″;V2 410 ′ 420 X = X + .0025 ′INCREMENT X6 OUTPUT BY 2.5 MV 430 IF X>10 THEN X 0 ′RESET RAMP 440 X$ = X6$ + STR$(X) + ″′ 13″′MAKE X6 COMMAND STRING 450 CALL TRANSMIT (X$,STATUS%) ′SET NEW X6 VOLTAGE 460 GOSUB 600 470 ′ 480 GOTO 300 ′LOOP FOREVER 490 ′ 500 ′ GET AN ANSWER STRING FROM THE SR530 510 CALL TRANSMIT(LISN$,STATUS%) ′MAKE SR530 A TALKER 520 GOSUB 600 530 ANS$=SPACE$(10) ′INIT ANSWER STRING 540 CALL RECV(ANS$,LENGTH%STATUS%) ′READ RESULT INTO ANS$ 550 GOSUB 600 560 RETURN 570 ′ 580 ′ 590 ′ CHECK STATUS OF LAST TRANSMISSION FOR ERRORS 600 IF STATUS%=0 THEN RETURN ′STATUS OKAY 610 PRINT ″STATUS CODE = ″;STATUS%;″ ON GPIB: ERROR″ 620 STOP

Program Example 5: HP85 via GPIB

This program provides an example of an HP85 program using the GPIB interface which could be used to control the lockin amplifier. In this example, the SR530 should be addressed as device #16 by setting the switch bank SW1 per the instructions Page 7.

10 x=0 20 OUTPUT 716 ; ″Q″ 30 ENTER 716 : V1 40 DISP ″CH1 = ″ : V1 50 OUTPUT 716 ; ″Q2″ 60 ENTER 716 : V2 70 DISP ″CH2 = ″ : V2 80 X = X + .0025 90 IF X>10 THEN X=0 100 OUTPUT 716 : ″X6, ″;X 110 GOTO 20

Documentation

This section contains the parts lists and schematics for the SR530 lock-in amplifier.

The first digit of any part number can be used to locate the schematic diagram for the part. For example, R415 is located on sheet 4 of the schematic diagrams.

SR530 COMPONENT PARTS LIST

Oscillator Board Parts List

REF. SRS part# VALUE DESCRIPTION

C 1 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 2 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 3 5-00102-517 4.7U Capacitor, Tantalum, 35V, 20%, Rad C 4 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 5 5-00087-516 390P Capacitor, Silver Mica, 500V, 5%, DM15 C 6 5-00102-517 4.7U Capacitor, Tantalum, 35V, 20%, Rad C 7 5-00014-501 390P Capacitor, Ceramic Disc, 50V, 10%, SL C 8 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 9 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 10 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 11 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad P 1 4-00016-445 10K Pot, Multi-Turn, Side Adjust P 2 4-00003-440 100K Trim Pot, Single Turn, In-Line Leads P 3 4-00016-445 10K Pot, Multi-Turn, Side Adjust PC1 7-00037-701 SR501 Printed Circuit Board R 1 4-00079-401 4.7K Resistor, Carbon Film, 1/4W, 5% R 2 4-00083-401 47K Resistor, Carbon Film, 1/4W, 5% R 3 4-00202-407 698 Resistor, Metal Film, 1/8W, 1%, 50PPM R 4 4-00189-407 41.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 5 4-00186-407 4.22K Resistor, Metal Film, 1/8W, 1%, 50PPM R 6 4-00190-407 42.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 7 4-00186-407 4.22K Resistor, Metal Film, 1/8W, 1%, 50PPM R 8 4-00202-407 698 Resistor, Metal Film, 1/8W, 1%, 50PPM R 9 4-00078-401 39K Resistor, Carbon Film, 1/4W, 5% R 10 4-00186-407 4.22K Resistor, Metal Film, 1/8W, 1%, 50PPM R 11 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 12 4-00042-401 15K Resistor, Carbon Film, 1/4W, 5% R 13 4-00070-401 30K Resistor, Carbon Film, 1/4W, 5% R 14 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 15 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 16 4-00079-401 4.7K Resistor, Carbon Film, 1/4W, 5% R 17 4-00104-401 82K Resistor, Carbon Film, 1/4W, 5% R 18 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 19 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 20 4-00188-407 4.99K Resistor, Metal Film, 1/8W, 1%, 50PPM R 21 4-00188-407 4.99K Resistor, Metal Film, 1/8W, 1%, 50PPM R 22 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 23 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 24 4-00031-401 100 Resistor, Carbon Film, 1/4W, 5% R 25 4-00031-401 100 Resistor, Carbon Film, 1/4W, 5% SW1 2-00013-215 DPDT Switch, Toggle Right Angle PCB Mount SW2 2-00013-215 DPDT Switch, Toggle Right Angle PCB Mount U 1 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 2 3-00085-340 ICL8038 Integrated Circuit (Thru-hole Pkg) U 3 3-00118-325 78L15 Transistor, TO-92 Package U 4 3-00124-325 79L15 Transistor, TO-92 Package Z 0 0-00100-040 1/4X1/16 Washer, Flat Z 0 0-00122-053 2-1/4" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00136-053 8-1/2" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin

SR530 COMPONENT PARTS LIST

Main Board Parts List

REF. SRS part# VALUE DESCRIPTION

BR1 3-00062-340 KBP201G/BR-81D Integrated Circuit (Thru-hole Pkg) BR2 3-00062-340 KBP201G/BR-81D Integrated Circuit (Thru-hole Pkg) BT1 6-00001-612 BR-2/3A 2PIN PC Battery C 101 5-00069-513 .1U Capacitor, Mylar/Poly, 50V, 5%, Rad C 102 5-00069-513 .1U Capacitor, Mylar/Poly, 50V, 5%, Rad C 103 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 104 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 105 5-00002-501 100P Capacitor, Ceramic Disc, 50V, 10%, SL C 106 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 107 5-00030-520 2200U Capacitor, Electrolytic, 16V, 20%, Rad C 108 5-00030-520 2200U Capacitor, Electrolytic, 16V, 20%, Rad C 110 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 111 5-00081-516 1P Capacitor, Silver Mica, 500V, 5%, DM15 C 116 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 117 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 118 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 120 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 121 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 122 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 123 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 124 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 125 5-00030-520 2200U Capacitor, Electrolytic, 16V, 20%, Rad C 126 5-00030-520 2200U Capacitor, Electrolytic, 16V, 20%, Rad C 127 5-00057-512 .22U Cap, Stacked Metal Film 50V 5% -40/+85c C 128 5-00057-512 .22U Cap, Stacked Metal Film 50V 5% -40/+85c C 129 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 131 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 132 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 133 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 134 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 136 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 137 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 145 5-00009-501 24P Capacitor, Ceramic Disc, 50V, 10%, SL C 146 5-00009-501 24P Capacitor, Ceramic Disc, 50V, 10%, SL C 147 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 148 5-00017-501 47P Capacitor, Ceramic Disc, 50V, 10%, SL C 201 5-00020-501 7.5P Capacitor, Ceramic Disc, 50V, 10%, SL C 202 5-00109-525 150P Capacitor, Poly s tyr ene, 50V, 5%, Ax C 203 5-00048-566 .0015U Cap, Polyester Film 50V 5% -40/+85c Rad C 204 5-00051-512 .015U Cap, Stacked Metal Film 50V 5% -40/+85c C 205 5-00055-512 .15U Cap, Stacked Metal Film 50V 5% -40/+85c C 206 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 207 5-00059-512 .47U Cap, Stacked Metal Film 50V 5% -40/+85c C 208 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 209 5-00109-525 150P Capacitor, Poly s tyr ene, 50V, 5%, Ax C 210 5-00048-566 .0015U Cap, Polyester Film 50V 5% -40/+85c Rad C 211 5-00051-512 .015U Cap, Stacked Metal Film 50V 5% -40/+85c C 212 5-00055-512 .15U Cap, Stacked Metal Film 50V 5% -40/+85c C 213 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c

SR530 COMPONENT PARTS LIST

REF.

C 214 5-00059-512 .47U Cap, Stacked Metal Film 50V 5% -40/+85c C 215 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 216 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 217 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 218 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 230 5-00055-512 .15U Cap, Stacked Metal Film 50V 5% -40/+85c C 301 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 302 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 303 5-00009-501 24P Capacitor, Ceramic Disc, 50V, 10%, SL C 304 5-00110-525 560P Capacitor, Poly s tyr ene, 50V, 5%, Ax C 305 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 306 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 307 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 308 5-00058-512 .33U Cap, Stacked Metal Film 50V 5% -40/+85c C 310 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 311 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 312 5-00017-501 47P Capacitor, Ceramic Disc, 50V, 10%, SL C 313 5-00017-501 47P Capacitor, Ceramic Disc, 50V, 10%, SL C 314 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 315 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 317 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 318 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 319 5-00058-512 .33U Cap, Stacked Metal Film 50V 5% -40/+85c C 320 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 321 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 322 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 323 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 324 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 325 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 326 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 327 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 328 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 329 5-00033-520 47U Capacitor, Electrolytic, 16V, 20%, Rad C 330 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 331 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 332 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 333 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 334 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 335 5-00016-501 470P Capacitor, Ceramic Disc, 50V, 10%, SL C 336 5-00016-501 470P Capacitor, Ceramic Disc, 50V, 10%, SL C 337 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 338 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 401 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 402 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 403 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 404 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 405 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 406 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 407 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 408 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 409 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

C 410 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 411 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 412 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 413 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 414 5-00053-512 .033U Cap, Stacked Metal Film 50V 5% -40/+85c C 415 5-00072-513 10U Capacitor, Mylar/Poly, 50V, 5%, Rad C 416 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 417 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 418 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 419 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 420 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 421 5-00013-501 33P Capacitor, Ceramic Disc, 50V, 10%, SL C 422 5-00013-501 33P Capacitor, Ceramic Disc, 50V, 10%, SL C 501 5-00012-501 330P Capacitor, Ceramic Disc, 50V, 10%, SL C 502 5-00136-519 .01U Capacitor, Polystyrene, 50V, 5%, Rad C 503 5-00007-501 220P Capacitor, Ceramic Disc, 50V, 10%, SL C 504 5-00002-501 100P Capacitor, Ceramic Disc, 50V, 10%, SL C 505 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 506 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 507 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 508 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 509 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 510 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 511 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 512 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 513 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 514 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 515 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 516 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 517 5-00002-501 100P Capacitor, Ceramic Disc, 50V, 10%, SL C 518 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 519 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 520 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 521 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 523 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 525 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 526 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 527 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 701 5-00007-501 220P Capacitor, Ceramic Disc, 50V, 10%, SL C 702 5-00007-501 220P Capacitor, Ceramic Disc, 50V, 10%, SL C 703 5-00040-509 1.0U Capacitor, Electrolytic, 50V, 20%, Rad C 704 5-00040-509 1.0U Capacitor, Electrolytic, 50V, 20%, Rad C 705 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 706 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 707 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 708 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 709 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 710 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 711 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 712 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 801 5-00012-501 330P Capacitor, Ceramic Disc, 50V, 10%, SL

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

C 802 5-00012-501 330P Capacitor, Ceramic Disc, 50V, 10%, SL C 803 5-00012-501 330P Capacitor, Ceramic Disc, 50V, 10%, SL C 804 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 805 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 806 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 807 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 808 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 809 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 901 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 902 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 903 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 904 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 905 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 906 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 907 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 908 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 909 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 910 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 911 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 912 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 913 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 914 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 915 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 916 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 917 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 918 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 919 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 920 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 923 5-00192-542 22U MIN Cap, Mini Electrolytic, 50V, 20% Radial C 924 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 925 5-00046-510 2200U Capacitor, Electrolytic, 50V, 20%, Ax C 926 5-00046-510 2200U Capacitor, Electrolytic, 50V, 20%, Ax C 927 5-00192-542 22U MIN Cap, Mini Electrolytic, 50V, 20% Radial C 928 5-00192-542 22U MIN Cap, Mini Electrolytic, 50V, 20% Radial C 929 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 930 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 931 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 932 5-00034-526 100U Capacitor, Electrolytic, 35V, 20%, Rad C 933 5-00103-524 1.0U Capacitor, Tantalum, 50V, 20%, Rad C 934 5-00103-524 1.0U Capacitor, Tantalum, 50V, 20%, Rad C 935 5-00036-522 6800U Cap, Electro. 25V 10% Ax, Mallory TCX C 936 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 937 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 938 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 939 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad CN801 1-00014-160 9 PIN D Connector, D-Sub, Right Angle PC, Female CN802 1-00016-160 RS232 25 PIN D Connector, D-Sub, Right Angle PC, Female CN803 1-00238-161 GPIB SHIELDED Connector, IEEE488, Reverse, R/A, Female CX1 5-00010-501 270P Capacitor, Ceramic Disc, 50V, 10%, SL CX713 5-00014-501 390P Capacitor, Ceramic Disc, 50V, 10%, SL CX714 5-00014-501 390P Capacitor, Ceramic Disc, 50V, 10%, SL

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

CY1 6-00010-620 4.000 MHZ Crystal D 101 3-00004-301 1N4148 Diode D 102 3-00004-301 1N4148 Diode D 103 3-00004-301 1N4148 Diode D 104 3-00004-301 1N4148 Diode D 105 3-00004-301 1N4148 Diode D 106 3-00004-301 1N4148 Diode D 201 3-00004-301 1N4148 Diode D 202 3-00004-301 1N4148 Diode D 203 3-00004-301 1N4148 Diode D 204 3-00004-301 1N4148 Diode D 301 3-00004-301 1N4148 Diode D 302 3-00004-301 1N4148 Diode D 303 3-00004-301 1N4148 Diode D 401 3-00004-301 1N4148 Diode D 402 3-00004-301 1N4148 Diode D 403 3-00004-301 1N4148 Diode D 404 3-00004-301 1N4148 Diode D 501 3-00004-301 1N4148 Diode D 502 3-00004-301 1N4148 Diode D 701 3-00007-301 1N747A Diode D 702 3-00203-301 1N5711 Diode D 703 3-00203-301 1N5711 Diode D 704 3-00004-301 1N4148 Diode D 901 3-00003-301 1N4007 Diode D 902 3-00003-301 1N4007 Diode D 903 3-00003-301 1N4007 Diode D 904 3-00003-301 1N4007 Diode FU1 6-00004-611 1A 3AG Fuse P 101 4-00006-440 20 Trim Pot, Single Turn, In-Line Leads P 102 4-00012-441 20K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 103 4-00012-441 20K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 104 4-00013-441 50K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 105 4-00014-441 5K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 401 4-00011-441 10K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 402 4-00011-441 10K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 403 4-00011-441 10K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 404 4-00011-441 10K Pot, Multi-Turn Trim, 3/8" Square Top Ad P 501 4-00002-440 100 Trim Pot, Single Turn, In-Line Leads P 502 4-00002-440 100 Trim Pot, Single Turn, In-Line Leads PC1 7-00036-701 SR500 Printed Circuit Board Q 101 3-00016-323 2N6485 Transistor, TO-71 Package Q 102 3-00016-323 2N6485 Transistor, TO-71 Package Q 103 3-00031-325 MPSA18 Transistor, TO-92 Package Q 201 3-00887-325 MPS2907A Transistor, TO-92 Package Q 202 3-00026-325 2N5210 Transistor, TO-92 Package Q 502 3-00026-325 2N5210 Transistor, TO-92 Package Q 701 3-00026-325 2N5210 Transistor, TO-92 Package Q 702 3-00026-325 2N5210 Transistor, TO-92 Package Q 703 3-00026-325 2N5210 Transistor, TO-92 Package R 101 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5%

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 102 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 103 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 104 4-00031-401 100 Resistor, Carbon Film, 1/4W, 5% R 105 4-00031-401 100 Resistor, Carbon Film, 1/4W, 5% R 108 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 109 4-00199-407 6.81K Resistor, Metal Film, 1/8W, 1%, 50PPM R 110 4-00199-407 6.81K Resistor, Metal Film, 1/8W, 1%, 50PPM R 111 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 112 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 113 4-00145-407 110 Resistor, Metal Film, 1/8W, 1%, 50PPM R 114 4-00145-407 110 Resistor, Metal Film, 1/8W, 1%, 50PPM R 115 4-00047-401 2.2 Resistor, Carbon Film, 1/4W, 5% R 116 4-00196-407 6.04K Resistor, Metal Film, 1/8W, 1%, 50PPM R 117 4-00210-407 9.09K Resistor, Metal Film, 1/8W, 1%, 50PPM R 118 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 119 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 120 4-00180-407 301 Resistor, Metal Film, 1/8W, 1%, 50PPM R 121 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 122 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 126 4-00210-407 9.09K Resistor, Metal Film, 1/8W, 1%, 50PPM R 127 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 128 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 130 4-00082-401 470K Resistor, Carbon Film, 1/4W, 5% R 132 4-00082-401 470K Resistor, Carbon Film, 1/4W, 5% R 133 4-00179-407 30.1K Resistor, Metal Film, 1/8W, 1%, 50PPM R 134 4-00179-407 30.1K Resistor, Metal Film, 1/8W, 1%, 50PPM R 135 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 138 4-00052-401 20 Resistor, Carbon Film, 1/4W, 5% R 139 4-00052-401 20 Resistor, Carbon Film, 1/4W, 5% R 140 4-00150-407 13.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 141 4-00174-407 280 Resistor, Metal Film, 1/8W, 1%, 50PPM R 142 4-00168-407 22.6K Resistor, Metal Film, 1/8W, 1%, 50PPM R 143 4-00150-407 13.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 144 4-00157-407 16.9K Resistor, Metal Film, 1/8W, 1%, 50PPM R 145 4-00157-407 16.9K Resistor, Metal Film, 1/8W, 1%, 50PPM R 146 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 147 4-00180-407 301 Resistor, Metal Film, 1/8W, 1%, 50PPM R 148 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 149 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 150 4-00179-407 30.1K Resistor, Metal Film, 1/8W, 1%, 50PPM R 151 4-00201-407 634 Resistor, Metal Film, 1/8W, 1%, 50PPM R 152 4-00195-407 54.9K Resistor, Metal Film, 1/8W, 1%, 50PPM R 153 4-00176-407 3.01K Resistor, Metal Film, 1/8W, 1%, 50PPM R 154 4-00178-407 3.83K Resistor, Metal Film, 1/8W, 1%, 50PPM R 155 4-00211-407 9.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 156 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 157 4-00180-407 301 Resistor, Metal Film, 1/8W, 1%, 50PPM R 158 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 159 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 160 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 161 4-00204-407 750 Resistor, Metal Film, 1/8W, 1%, 50PPM

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 162 4-00188-407 4.99K Resistor, Metal Film, 1/8W, 1%, 50PPM R 163 4-00035-401 10M Resistor, Carbon Film, 1/4W, 5% R 165 4-00215-407 909 Resistor, Metal Film, 1/8W, 1%, 50PPM R 166 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 167 4-00215-407 909 Resistor, Metal Film, 1/8W, 1%, 50PPM R 168 4-00141-407 100 Resistor, Metal Film, 1/8W, 1%, 50PPM R 169 4-00134-407 1.24K Resistor, Metal Film, 1/8W, 1%, 50PPM R 170 4-00144-407 107 Resistor, Metal Film, 1/8W, 1%, 50PPM R 171 4-00182-407 33.2 Resistor, Metal Film, 1/8W, 1%, 50PPM R 172 4-00035-401 10M Resistor, Carbon Film, 1/4W, 5% R 173 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 174 4-00180-407 301 Resistor, Metal Film, 1/8W, 1%, 50PPM R 175 4-00165-407 200 Resistor, Metal Film, 1/8W, 1%, 50PPM R 176 4-00211-407 9.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 177 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 178 4-00035-401 10M Resistor, Carbon Film, 1/4W, 5% R 201 4-00135-407 1.50K Resistor, Metal Film, 1/8W, 1%, 50PPM R 202 4-00194-407 5.11K Resistor, Metal Film, 1/8W, 1%, 50PPM R 203 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 204 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 205 4-00153-407 15.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 206 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 207 4-00135-407 1.50K Resistor, Metal Film, 1/8W, 1%, 50PPM R 208 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 209 4-00150-407 13.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 210 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 211 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 212 4-00135-407 1.50K Resistor, Metal Film, 1/8W, 1%, 50PPM R 213 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 214 4-00150-407 13.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 215 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 216 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 217 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 218 4-00035-401 10M Resistor, Carbon Film, 1/4W, 5% R 219 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 220 4-00177-407 3.48K Resistor, Metal Film, 1/8W, 1%, 50PPM R 221 4-00039-401 120K Resistor, Carbon Film, 1/4W, 5% R 222 4-00096-401 62K Resistor, Carbon Film, 1/4W, 5% R 223 4-00039-401 120K Resistor, Carbon Film, 1/4W, 5% R 224 4-00094-401 6.8K Resistor, Carbon Film, 1/4W, 5% R 225 4-00063-401 3.0K Resistor, Carbon Film, 1/4W, 5% R 226 4-00094-401 6.8K Resistor, Carbon Film, 1/4W, 5% R 227 4-00063-401 3.0K Resistor, Carbon Film, 1/4W, 5% R 228 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 229 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 301 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 302 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 303 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 304 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 305 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 306 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5%

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 307 4-00040-401 13K Resistor, Carbon Film, 1/4W, 5% R 308 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 309 4-00073-401 330K Resistor, Carbon Film, 1/4W, 5% R 310 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 311 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 312 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 313 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 314 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 315 4-00099-401 680K Resistor, Carbon Film, 1/4W, 5% R 316 4-00099-401 680K Resistor, Carbon Film, 1/4W, 5% R 317 4-00093-401 6.2K Resistor, Carbon Film, 1/4W, 5% R 318 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 319 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 320 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 321 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 322 4-00170-407 249K Resistor, Metal Film, 1/8W, 1%, 50PPM R 323 4-00199-407 6.81K Resistor, Metal Film, 1/8W, 1%, 50PPM R 324 4-00199-407 6.81K Resistor, Metal Film, 1/8W, 1%, 50PPM R 325 4-00163-407 2.80K Resistor, Metal Film, 1/8W, 1%, 50PPM R 326 4-00150-407 13.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 327 4-00159-407 2.10K Resistor, Metal Film, 1/8W, 1%, 50PPM R 328 4-00029-401 1.8K Resistor, Carbon Film, 1/4W, 5% R 329 4-00088-401 51K Resistor, Carbon Film, 1/4W, 5% R 330 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 332 4-00161-407 2.49K Resistor, Metal Film, 1/8W, 1%, 50PPM R 333 4-00029-401 1.8K Resistor, Carbon Film, 1/4W, 5% R 334 4-00197-407 6.49K Resistor, Metal Film, 1/8W, 1%, 50PPM R 335 4-00088-401 51K Resistor, Carbon Film, 1/4W, 5% R 336 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 337 4-00035-401 10M Resistor, Carbon Film, 1/4W, 5% R 338 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 339 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 340 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 341 4-00025-401 1.2M Resistor, Carbon Film, 1/4W, 5% R 342 4-00073-401 330K Resistor, Carbon Film, 1/4W, 5% R 343 4-00046-401 2.0M Resistor, Carbon Film, 1/4W, 5% R 344 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 345 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 346 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 347 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 348 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 349 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 350 4-00093-401 6.2K Resistor, Carbon Film, 1/4W, 5% R 351 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 352 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 353 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 354 4-00203-407 75.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 355 4-00187-407 4.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 356 4-00160-407 2.26K Resistor, Metal Film, 1/8W, 1%, 50PPM R 357 4-00163-407 2.80K Resistor, Metal Film, 1/8W, 1%, 50PPM R 358 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5%

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 359 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 360 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 361 4-00084-401 5.1K Resistor, Carbon Film, 1/4W, 5% R 362 4-00181-407 32.4K Resistor, Metal Film, 1/8W, 1%, 50PPM R 363 4-00132-407 1.10K Resistor, Metal Film, 1/8W, 1%, 50PPM R 364 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 365 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 366 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 367 4-00151-407 130K Resistor, Metal Film, 1/8W, 1%, 50PPM R 368 4-00156-407 16.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 369 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 370 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 371 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 372 4-00023-401 1.1M Resistor, Carbon Film, 1/4W, 5% R 373 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 374 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 375 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 376 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 377 4-00187-407 4.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 378 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 401 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 402 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 403 4-00085-401 5.1M Resistor, Carbon Film, 1/4W, 5% R 404 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 405 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 406 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 407 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 408 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 409 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 410 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 411 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 412 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 413 4-00203-407 75.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 414 4-00080-401 47 Resistor, Carbon Film, 1/4W, 5% R 415 4-00142-407 100K Resistor, Metal Film, 1/8W, 1%, 50PPM R 417 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 418 4-00132-407 1.10K Resistor, Metal Film, 1/8W, 1%, 50PPM R 419 4-00179-407 30.1K Resistor, Metal Film, 1/8W, 1%, 50PPM R 420 4-00183-407 348K Resistor, Metal Film, 1/8W, 1%, 50PPM R 421 4-00155-407 150K Resistor, Metal Film, 1/8W, 1%, 50PPM R 422 4-00184-407 37.4K Resistor, Metal Film, 1/8W, 1%, 50PPM R 423 4-00212-407 9.76K Resistor, Metal Film, 1/8W, 1%, 50PPM R 424 4-00161-407 2.49K Resistor, Metal Film, 1/8W, 1%, 50PPM R 425 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 426 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 427 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 428 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 429 4-00146-407 110K Resistor, Metal Film, 1/8W, 1%, 50PPM R 430 4-00140-407 10.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 431 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 432 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5%

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 433 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 501 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 502 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 503 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 504 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 505 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 506 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 507 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 508 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 509 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 510 4-00219-408 20.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 511 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 512 4-00219-408 20.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 513 4-00166-407 200K Resistor, Metal Film, 1/8W, 1%, 50PPM R 514 4-00207-407 806K Resistor, Metal Film, 1/8W, 1%, 50PPM R 515 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 516 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 518 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 519 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 520 4-00086-401 51 Resistor, Carbon Film, 1/4W, 5% R 521 4-00086-401 51 Resistor, Carbon Film, 1/4W, 5% R 522 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 523 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 524 4-00078-401 39K Resistor, Carbon Film, 1/4W, 5% R 525 4-00059-401 22K Resistor, Carbon Film, 1/4W, 5% R 526 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 527 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 528 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 529 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 530 4-00210-407 9.09K Resistor, Metal Film, 1/8W, 1%, 50PPM R 531 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 532 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 533 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 534 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 535 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 536 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 537 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 538 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 539 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 540 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 541 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 542 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 543 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 544 4-00042-401 15K Resistor, Carbon Film, 1/4W, 5% R 545 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 546 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 547 4-00042-401 15K Resistor, Carbon Film, 1/4W, 5% R 548 4-00054-401 200K Resistor, Carbon Film, 1/4W, 5% R 549 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 701 4-00031-401 100 Resistor, Carbon Film, 1/4W, 5% R 702 4-00079-401 4.7K Resistor, Carbon Film, 1/4W, 5%

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 703 4-00027-401 1.5K Resistor, Carbon Film, 1/4W, 5% R 705 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 706 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 707 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 708 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 709 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 710 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 711 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 712 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 801 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 802 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 803 4-00065-401 3.3K Resistor, Carbon Film, 1/4W, 5% R 901 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% R 902 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% R 903 4-00060-401 240 Resistor, Carbon Film, 1/4W, 5% R 904 4-00024-401 1.2K Resistor, Carbon Film, 1/4W, 5% R 905 4-00024-401 1.2K Resistor, Carbon Film, 1/4W, 5% R 906 4-00060-401 240 Resistor, Carbon Film, 1/4W, 5% R 907 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% R 908 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% R 909 4-00053-401 200 Resistor, Carbon Film, 1/4W, 5% R 910 4-00063-401 3.0K Resistor, Carbon Film, 1/4W, 5% R 911 4-00063-401 3.0K Resistor, Carbon Film, 1/4W, 5% R 912 4-00053-401 200 Resistor, Carbon Film, 1/4W, 5% R 913 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% R 914 4-00107-402 10 Resistor, Carbon Comp, 1/2W, 5% RN401 4-00220-420 10KX8 Resistor Network, DIP, 1/4W,2%,8 Ind RN801 4-00225-425 100KX9 Resistor Network SIP 1/4W 2% (Common) RN802 4-00225-425 100KX9 Resistor Network SIP 1/4W 2% (Common) SO702 1-00026-150 28 PIN 600 MIL Socket, THRU-HOLE SW1 2-00014-207 SPSTX8 Switch, DIP SW2 2-00014-207 SPSTX8 Switch, DIP SW601 2-00017-216 4PDT Switch, Rocker, PCB Mount (LHS of 510) SW602 2-00004-213 DPDT Switch, Rocker, PCB Mount (RHS of 510) T 1 6-00007-610 SR510/530 Transformer U 101 8-00085-860 SR513 ASSY SRS sub assemblies U 102 8-00085-860 SR513 ASSY SRS sub assemblies U 103 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 104 3-00118-325 78L15 Transistor, TO-92 Package U 105 3-00124-325 79L15 Transistor, TO-92 Package U 106 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 107 3-00130-340 5532A Integrated Circuit (Thru-hole Pkg) U 108 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 109 3-00088-340 LF353 Integrated Circuit (Thru-hole Pkg) U 110 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 111 3-00089-340 LF357 Integrated Circuit (Thru-hole Pkg) U 112 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 113 3-00089-340 LF357 Integrated Circuit (Thru-hole Pkg) U 114 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 115 3-00089-340 LF357 Integrated Circuit (Thru-hole Pkg) U 117 3-00088-340 LF353 Integrated Circuit (Thru-hole Pkg)

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

U 118 3-00130-340 5532A Integrated Circuit (Thru-hole Pkg) U 201 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 202 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 203 3-00073-340 CD4052 Integrated Circuit (Thru-hole Pkg) U 204 3-00073-340 CD4052 Integrated Circuit (Thru-hole Pkg) U 205 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 206 3-00038-340 74HC139 Integrated Circuit (Thru-hole Pkg) U 207 3-00038-340 74HC139 Integrated Circuit (Thru-hole Pkg) U 208 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 301 3-00088-340 LF353 Integrated Circuit (Thru-hole Pkg) U 303 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 304 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 305 3-00075-340 CD4538 Integrated Circuit (Thru-hole Pkg) U 306 3-00072-340 CD4046 Integrated Circuit (Thru-hole Pkg) U 307 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 308 3-00066-340 CA3140E Integrated Circuit (Thru-hole Pkg) U 309 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 310 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 311 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 312 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 313 3-00049-340 74HC74 Integrated Circuit (Thru-hole Pkg) U 314 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 315 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 316 3-00072-340 CD4046 Integrated Circuit (Thru-hole Pkg) U 317 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 318 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 319 3-00066-340 CA3140E Integrated Circuit (Thru-hole Pkg) U 320 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 321 3-00066-340 CA3140E Integrated Circuit (Thru-hole Pkg) U 322 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 323 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 324 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 325 3-00091-340 LF412 Integrated Circuit (Thru-hole Pkg) U 326 3-00068-340 CD4018 Integrated Circuit (Thru-hole Pkg) U 327 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 328 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 329 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 401 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 402 3-00091-340 LF412 Integrated Circuit (Thru-hole Pkg) U 403 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 404 3-00106-340 LT1007 Integrated Circuit (Thru-hole Pkg) U 405 3-00074-340 CD4066 Integrated Circuit (Thru-hole Pkg) U 406 3-00057-340 AD534 Integrated Circuit (Thru-hole Pkg) U 407 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 408 3-00106-340 LT1007 Integrated Circuit (Thru-hole Pkg) U 409 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 410 3-00084-340 ICL7650 Integrated Circuit (Thru-hole Pkg) U 411 3-00126-335 51A05 Relay U 412 3-00126-335 51A05 Relay U 413 3-00126-335 51A05 Relay U 414 3-00126-335 51A05 Relay

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

U 415 3-00126-335 51A05 Relay U 416 3-00084-340 ICL7650 Integrated Circuit (Thru-hole Pkg) U 417 3-00126-335 51A05 Relay U 418 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 419 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 420 3-00064-340 CA3081 Integrated Circuit (Thru-hole Pkg) U 421 3-00035-340 74C74 Integrated Circuit (Thru-hole Pkg) U 501 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 502 3-00058-340 AD7524 Integrated Circuit (Thru-hole Pkg) U 503 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 504 3-00077-340 DG528 Integrated Circuit (Thru-hole Pkg) U 505 3-00059-340 AD7542JN Integrated Circuit (Thru-hole Pkg) U 506 3-00058-340 AD7524 Integrated Circuit (Thru-hole Pkg) U 507 3-00077-340 DG528 Integrated Circuit (Thru-hole Pkg) U 508 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 509 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 510 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 511 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 512 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 513 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 514 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 515 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 516 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 517 3-00092-340 LH0071 Integrated Circuit (Thru-hole Pkg) U 701 3-00132-340 Z80A-CPU Integrated Circuit (Thru-hole Pkg) U 703 3-00081-341 2KX8-100 STATIC RAM, I.C. U 704 3-00491-340 UPD71054C Integrated Circuit (Thru-hole Pkg) U 705 3-00037-340 74HC138 Integrated Circuit (Thru-hole Pkg) U 706 3-00037-340 74HC138 Integrated Circuit (Thru-hole Pkg) U 707 3-00037-340 74HC138 Integrated Circuit (Thru-hole Pkg) U 708 3-00040-340 74HC157 Integrated Circuit (Thru-hole Pkg) U 709 3-00049-340 74HC74 Integrated Circuit (Thru-hole Pkg) U 710 3-00045-340 74HC32 Integrated Circuit (Thru-hole Pkg) U 711 3-00051-340 74HCU04 Integrated Circuit (Thru-hole Pkg) U 712 3-00047-340 74HC4040 Integrated Circuit (Thru-hole Pkg) U 713 3-00049-340 74HC74 Integrated Circuit (Thru-hole Pkg) U 714 3-00042-340 74HC175 Integrated Circuit (Thru-hole Pkg) U 715 3-00042-340 74HC175 Integrated Circuit (Thru-hole Pkg) U 716 3-00044-340 74HC244 Integrated Circuit (Thru-hole Pkg) U 717 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 718 3-00039-340 74HC14 Integrated Circuit (Thru-hole Pkg) U 719 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 720 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 721 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 722 3-00045-340 74HC32 Integrated Circuit (Thru-hole Pkg) U 801 3-00493-340 UPD71051C Integrated Circuit (Thru-hole Pkg) U 802 3-00111-340 MC68488 Integrated Circuit (Thru-hole Pkg) U 803 3-00044-340 74HC244 Integrated Circuit (Thru-hole Pkg) U 804 3-00044-340 74HC244 Integrated Circuit (Thru-hole Pkg) U 805 3-00049-340 74HC74 Integrated Circuit (Thru-hole Pkg) U 806 3-00109-340 MC1488 Integrated Circuit (Thru-hole Pkg)

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

U 807 3-00110-340 MC1489 Integrated Circuit (Thru-hole Pkg) U 808 3-00078-340 DS75160A Integrated Circuit (Thru-hole Pkg) U 809 3-00117-325 78L12 Transistor, TO-92 Package U 810 3-00123-325 79L12 Transistor, TO-92 Package U 811 3-00079-340 DS75161A Integrated Circuit (Thru-hole Pkg) U 901 3-00095-331 LM317K Voltage Regulator, TO-3 Metal Can U 902 3-00099-331 LM337K Voltage Regulator, TO-3 Metal Can U 903 3-00114-329 7815 Voltage Reg., TO-220 (TAB) Package U 904 3-00114-329 7815 Voltage Reg., TO-220 (TAB) Package U 905 3-00114-329 7815 Voltage Reg., TO-220 (TAB) Package U 906 3-00120-329 7915 Voltage Reg., TO-220 (TAB) Package U 907 3-00120-329 7915 Voltage Reg., TO-220 (TAB) Package U 908 3-00120-329 7915 Voltage Reg., TO-220 (TAB) Package U 909 3-00113-340 7805CK Integrated Circuit (Thru-hole Pkg) U 910 3-00116-325 78L05 Transistor, TO-92 Package U 911 3-00096-340 LM317L Integrated Circuit (Thru-hole Pkg) U 912 3-00100-340 LM337L Integrated Circuit (Thru-hole Pkg) Z 0 0-00005-007 SR530 Heat Sinks Z 0 0-00014-002 6J4 Power_Entry Hardware Z 0 0-00016-000 TIE ANCHOR Hardware, Misc. Z 0 0-00017-002 TRANSCOVER Power_Entry Hardware Z 0 0-00019-003 MICA Insulators Z 0 0-00025-005 3/8" Lugs Z 0 0-00043- 01 1 4-40 KEP Nut, Kep Z 0 0-00048- 01 1 6-32 KEP Nut, Kep Z 0 0-00064-027 6-20X5/8P Screw, Sheet Metal Z 0 0-00079-031 4-40X3/16 M/F Standoff Z 0 0-00084-032 36154 Termination Z 0 0-00089-033 4" Tie Z 0 0-00095-040 #4 FLAT Washer, Flat Z 0 0-00096-041 #4 SPLIT Washer, Split Z 0 0-00113-053 10" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00117-053 12" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00119-053 15" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00128-053 4" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00130-050 5-5/8" #18 Wire #18 UL1007 Stripped 3/8x3/8 No Tin Z 0 0-00132-053 6-1/2" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00136-053 8-1/2" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00153-057 GROMMET2 Grommet Z 0 0-00185-021 6-32X3/8PP Screw, Panhead Phillips Z 0 0-00187-021 4-40X1/4PP Screw, Panhead Phillips Z 0 0-00207-003 TO-5 Insulators Z 0 0-00222-021 6-32X1/4PP Screw, Panhead Phillips Z 0 0-00225-052 17" #22 BLACK Wire #22 UL1007 Z 0 0-00226-052 17" #22 WHITE Wire #22 UL1007 Z 0 0-00227-052 17" #22 RED Wire #22 UL1007 Z 0 0-00228-052 17" #22 GREEN Wire #22 UL1007 Z 0 0-00231-043 #4 SHOULDER Washer, nylon Z 0 0-00241-021 4-40X3/16PP Screw, Panhead Phillips Z 0 0-00249-021 6-32X1-1/2PP Screw, Panhead Phillips Z 0 0-00256-043 #6 SHOULDER Washer, nylon

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

Z 0 0-00257-000 HANDLE3 Hardware, Misc. Z 0 0-00371-026 4-40X3/16PF Screw, Black, All Types Z 0 0-00500-000 554808-1 Hardware, Misc. Z 0 0-00521-048 3" #18 Wire, #18 UL1015 Strip 3/8 x 3/8 No Tin Z 0 0-00526-048 10-1/2" #18 Wire, #18 UL1015 Strip 3/8 x 3/8 No Tin Z 0 0-00893-026 8-32X3/8PF Screw, Black, All Types Z 0 1-00003-120 BNC Connector, BNC Z 0 1-00010-130 20 PIN ELH Connector, Male Z 0 1-00012-135 20 PIN CARD Connector, Card Edge Z 0 1-00013-135 40 PIN CARD Connector, Card Edge Z 0 1-00029-150 TO-3 Socket, THRU-HOLE Z 0 1-00053-172 USA Line Cord Z 0 7-00201-720 SR500-32 Fabricated Part Z 0 7-00202-720 SR500-33 Fabricated Part Z 0 7-00210-720 SR530-22 Fabricated Part Z 0 7-00212-720 SR530-26 Fabricated Part Z 0 7-00213-720 SR530-27 Fabricated Part Z 0 7-00214-720 SR530-28 Fabricated Part Z 0 9-00144-907 3/32"BLACK Shrink Tubing Z 0 9-00188-91 7 SR510/530 SER Product Labels Z 0 9-00216-907 1/8" BLACK Shrink Tubing Z 0 9-00217-907 3/16" BLACK Shrink Tubing

SRS part# VALUE DESCRIPTION

Front Panel Board Parts List

REF. SRS part# VALUE DESCRIPTION

C 607 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 608 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 609 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 610 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 6100 5-00019-501 68P Capacitor, Ceramic Disc, 50V, 10%, SL C 6101 5-00019-501 68P Capacitor, Ceramic Disc, 50V, 10%, SL C 6102 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 6103 5-00052-512 .01U Cap, Stacked Metal Film 50V 5% -40/+85c C 6105 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 6106 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U D 601 3-00004-301 1N4148 Diode D 602 3-00004-301 1N4148 Diode D 603 3-00004-301 1N4148 Diode D 604 3-00004-301 1N4148 Diode DS601 3- 0001 2- 30 6 GREEN LED, Rectangular DS602 3- 0001 2- 30 6 GREEN LED, Rectangular DS603 3- 0001 2- 30 6 GREEN LED, Rectangular DS604 3- 0001 2- 30 6 GREEN LED, Rectangular DS605 3- 0001 2- 30 6 GREEN LED, Rectangular DS606 3- 0001 2- 30 6 GREEN LED, Rectangular DS607 3- 0001 2- 30 6 GREEN LED, Rectangular DS608 3- 0001 2- 30 6 GREEN LED, Rectangular DS609 3- 0001 2- 30 6 GREEN LED, Rectangular DS610 3- 0001 2- 30 6 GREEN LED, Rectangular

SR530 COMPONENT PARTS LIST

REF.

DS611 3- 0001 2- 30 6 GREEN LED, Rectangular DS612 3- 0001 2- 30 6 GREEN LED, Rectangular DS613 3- 0001 2- 30 6 GREEN LED, Rectangular DS614 3- 0001 2- 30 6 GREEN LED, Rectangular DS615 3- 0001 2- 30 6 GREEN LED, Rectangular DS616 3- 0001 2- 30 6 GREEN LED, Rectangular DS617 3- 0001 2- 30 6 GREEN LED, Rectangular DS618 3- 0001 2- 30 6 GREEN LED, Rectangular DS619 3- 0001 2- 30 6 GREEN LED, Rectangular DS620 3- 0001 2- 30 6 GREEN LED, Rectangular DS621 3- 0001 2- 30 6 GREEN LED, Rectangular DS622 3- 0001 2- 30 6 GREEN LED, Rectangular DS623 3- 0001 2- 30 6 GREEN LED, Rectangular DS624 3- 0001 2- 30 6 GREEN LED, Rectangular DS625 3- 0001 2- 30 6 GREEN LED, Rectangular DS626 3- 0001 2- 30 6 GREEN LED, Rectangular DS627 3- 0001 2- 30 6 GREEN LED, Rectangular DS628 3- 0001 2- 30 6 GREEN LED, Rectangular DS629 3- 0001 2- 30 6 GREEN LED, Rectangular DS630 3- 0001 2- 30 6 GREEN LED, Rectangular DS631 3- 0001 2- 30 6 GREEN LED, Rectangular DS632 3- 0001 2- 30 6 GREEN LED, Rectangular DS633 3- 0001 2- 30 6 GREEN LED, Rectangular DS634 3- 0001 2- 30 6 GREEN LED, Rectangular DS635 3- 0001 2- 30 6 GREEN LED, Rectangular DS636 3- 0001 2- 30 6 GREEN LED, Rectangular DS637 3- 0001 2- 30 6 GREEN LED, Rectangular DS638 3- 0001 3- 30 6 RED LED, Rectangular DS639 3- 0001 3- 30 6 RED LED, Rectangular DS640 3- 0001 3- 30 6 RED LED, Rectangular DS641 3- 0001 2- 30 6 GREEN LED, Rectangular DS642 3- 0001 2- 30 6 GREEN LED, Rectangular DS643 3- 0001 2- 30 6 GREEN LED, Rectangular DS644 3- 0001 2- 30 6 GREEN LED, Rectangular DS645 3- 0001 2- 30 6 GREEN LED, Rectangular DS646 3- 0001 2- 30 6 GREEN LED, Rectangular DS647 3- 0001 2- 30 6 GREEN LED, Rectangular DS648 3- 0001 2- 30 6 GREEN LED, Rectangular DS649 3- 0001 2- 30 6 GREEN LED, Rectangular DS650 3- 0001 2- 30 6 GREEN LED, Rectangular DS651 3- 0001 2- 30 6 GREEN LED, Rectangular DS652 3- 0001 2- 30 6 GREEN LED, Rectangular DS653 3- 0001 2- 30 6 GREEN LED, Rectangular DS654 3- 0001 2- 30 6 GREEN LED, Rectangular DS655 3- 0001 2- 30 6 GREEN LED, Rectangular DS656 3- 0001 2- 30 6 GREEN LED, Rectangular DS657 3- 0001 2- 30 6 GREEN LED, Rectangular DS658 3- 0001 2- 30 6 GREEN LED, Rectangular DS659 3- 0001 2- 30 6 GREEN LED, Rectangular DS660 3- 0001 2- 30 6 GREEN LED, Rectangular DS661 3- 0001 2- 30 6 GREEN LED, Rectangular

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

DS662 3- 0001 2- 30 6 GREEN LED, Rectangular DS663 3- 0001 2- 30 6 GREEN LED, Rectangular DS664 3- 0001 2- 30 6 GREEN LED, Rectangular DS665 3- 0001 2- 30 6 GREEN LED, Rectangular DS666 3- 0001 2- 30 6 GREEN LED, Rectangular DS667 3- 0001 2- 30 6 GREEN LED, Rectangular DS668 3- 0001 2- 30 6 GREEN LED, Rectangular DS669 3- 0001 2- 30 6 GREEN LED, Rectangular DS670 3- 0001 2- 30 6 GREEN LED, Rectangular DS671 3- 0001 2- 30 6 GREEN LED, Rectangular LD1 8-00001-820 FE0206 LCD Display LD2 8-00001-820 FE0206 LCD Display LD3 8-00001-820 FE0206 LCD Display M 1 8-00003-801 -10/0/10S Analog Meter M 2 8-00003-801 -10/0/10S Analog Meter PB601 2-00001-201 D6-01-01 Switch, Momentary Push Button PB602 2-00001-201 D6-01-01 Switch, Momentary Push Button PB603 2-00001-201 D6-01-01 Switch, Momentary Push Button PB604 2-00001-201 D6-01-01 Switch, Momentary Push Button PB605 2-00001-201 D6-01-01 Switch, Momentary Push Button PB606 2-00001-201 D6-01-01 Switch, Momentary Push Button PB607 2-00001-201 D6-01-01 Switch, Momentary Push Button PB608 2-00001-201 D6-01-01 Switch, Momentary Push Button PB609 2-00001-201 D6-01-01 Switch, Momentary Push Button PB610 2-00001-201 D6-01-01 Switch, Momentary Push Button PB611 2-00001-201 D6-01-01 Switch, Momentary Push Button PB612 2-00001-201 D6-01-01 Switch, Momentary Push Button PB613 2-00001-201 D6-01-01 Switch, Momentary Push Button PB614 2-00001-201 D6-01-01 Switch, Momentary Push Button PB615 2-00001-201 D6-01-01 Switch, Momentary Push Button PB616 2-00001-201 D6-01-01 Switch, Momentary Push Button PB617 2-00001-201 D6-01-01 Switch, Momentary Push Button PB618 2-00001-201 D6-01-01 Switch, Momentary Push Button PB619 2-00001-201 D6-01-01 Switch, Momentary Push Button PB620 2-00001-201 D6-01-01 Switch, Momentary Push Button PB621 2-00001-201 D6-01-01 Switch, Momentary Push Button PB622 2-00001-201 D6-01-01 Switch, Momentary Push Button PB623 2-00001-201 D6-01-01 Switch, Momentary Push Button PB624 2-00001-201 D6-01-01 Switch, Momentary Push Button PB625 2-00001-201 D6-01-01 Switch, Momentary Push Button PB626 2-00001-201 D6-01-01 Switch, Momentary Push Button PB627 2-00001-201 D6-01-01 Switch, Momentary Push Button PB628 2-00001-201 D6-01-01 Switch, Momentary Push Button PB629 2-00001-201 D6-01-01 Switch, Momentary Push Button PB630 2-00001-201 D6-01-01 Switch, Momentary Push Button PB631 2-00001-201 D6-01-01 Switch, Momentary Push Button PC1 7-00039-701 SR521 Printed Circuit Board R 601 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 602 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% RN601 4-00227-425 22KX9 Resistor Network SIP 1/4W 2% (Common) RN602 4-00226-425 150X9 Resistor Network SIP 1/4W 2% (Common)

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

RN603 4-00226-425 150X9 Resistor Network SIP 1/4W 2% (Common) RN604 4-00222-425 150X7 Resistor Network SIP 1/4W 2% (Common) U 601 3-00086-340 ICM7211AM Integrated Circuit (Thru-hole Pkg) U 602 3-00086-340 ICM7211AM Integrated Circuit (Thru-hole Pkg) U 603 3-00086-340 ICM7211AM Integrated Circuit (Thru-hole Pkg) U 604 3-00071-340 CD4030 Integrated Circuit (Thru-hole Pkg) U 605 3-00071-340 CD4030 Integrated Circuit (Thru-hole Pkg) U 606 3-00071-340 CD4030 Integrated Circuit (Thru-hole Pkg) U 607 3-00046-340 74HC374 Integrated Circuit (Thru-hole Pkg) U 608 3-00042-340 74HC175 Integrated Circuit (Thru-hole Pkg) U 609 3-00044-340 74HC244 Integrated Circuit (Thru-hole Pkg) U 610 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 611 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 612 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 613 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 614 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 615 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 616 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 617 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) U 618 3-00053-340 74LS164 Integrated Circuit (Thru-hole Pkg) Z 0 0-00042-010 4-40 HEX Nut, Hex Z 0 0-00077-030 3/16"X5/16"NYLN Spacer Z 0 0-00102-04 2 #10 LOCK Washer, lock Z 0 0-00104-043 #4 NYLON Washer, nylon Z 0 0-00106-044 CLEAR Window Z 0 0-00111-053 1-3/4"#24B Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00112-053 1-3/4"#24R Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00117-053 12" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00118-053 14" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00119-053 15" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00126-053 3-1/2" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00128-053 4" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00129-053 5" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00136-053 8-1/2" #24 Wire #24 UL1007 Strip 1/4x1/4 Tin Z 0 0-00139-054 9" #26 X20 Wire #26 UL1061 Z 0 0-00203-032 323914 Termination Z 0 1-00011-130 20 PIN IDP Connector, Male Z 0 1-00073-120 INSL Connector, BNC Z 0 1-00145-131 20 PIN DIF POL Connector, Female Z 0 7-00305-710 SR530-31 Front Panel Z 0 7-00306-709 SR530-32-36 Lexan Overlay Z 0 9-00815-924 DBL-SIDED 1/2" Tape, All types

SRS part# VALUE DESCRIPTION

Quad Board Parts List

REF. SRS part# VALUE DESCRIPTION

C 1001 5-00016-501 470P Capacitor, Ceramic Disc, 50V, 10%, SL C 1002 5-00038-509 10U Capacitor, Electrolytic, 50V, 20%, Rad C 1004 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 1005 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad

SR530 COMPONENT PARTS LIST

REF.

C 1006 5-00058-512 .33U Cap, Stacked Metal Film 50V 5% -40/+85c C 1007 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 1008 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 1009 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 1010 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 1011 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 1012 5-00035-521 47U Capacitor, Electrolytic, 25V, 20%, Rad C 1013 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 1014 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 1015 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 1016 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 1017 5-00100-517 2.2U Capacitor, Tantalum, 35V, 20%, Rad C 1018 5-00008-501 22P Capacitor, Ceramic Disc, 50V, 10%, SL C 1101 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 1102 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1103 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1104 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 1105 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 1106 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1107 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1108 5-00003-501 10P Capacitor, Ceramic Disc, 50V, 10%, SL C 1109 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 1110 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 1111 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 1112 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 1113 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 1114 5-00053-512 .033U Cap, Stacked Metal Film 50V 5% -40/+85c C 1115 5-00072-513 10U Capacitor, Mylar/Poly, 50V, 5%, Rad C 1116 5-00056-512 .1U Cap, Stacked Metal Film 50V 5% -40/+85c C 1117 5-00060-512 1.0U Cap, Stacked Metal Film 50V 5% -40/+85c C 1120 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 1121 5-00013-501 33P Capacitor, Ceramic Disc, 50V, 10%, SL C 1122 5-00013-501 33P Capacitor, Ceramic Disc, 50V, 10%, SL C 1123 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 1124 5-00054-512 .047U Cap, Stacked Metal Film 50V 5% -40/+85c C 1125 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1126 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1201 5-00012-501 330P Capacitor, Ceramic Disc, 50V, 10%, SL C 1202 5-00136-519 .01U Capacitor, Polystyrene, 50V, 5%, Rad C 1203 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 1204 5-00049-566 .001U Cap, Polyester Film 50V 5% -40/+85c Rad C 1205 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1206 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1207 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U C 1208 5-00023-529 .1U Cap, Monolythic Ceramic, 50V, 20%, Z5U D 1001 3-00004-301 1N4148 Diode D 1002 3-00004-301 1N4148 Diode D 1103 3-00004-301 1N4148 Diode D 1104 3-00004-301 1N4148 Diode P 1101 4-00016-445 10K Pot, Multi-Turn, Side Adjust P 1102 4-00016-445 10K Pot, Multi-Turn, Side Adjust

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

P 1103 4-00016-445 10K Pot, Multi-Turn, Side Adjust P 1104 4-00016-445 10K Pot, Multi-Turn, Side Adjust P 1201 4-00016-445 10K Pot, Multi-Turn, Side Adjust P 1202 4-00016-445 10K Pot, Multi-Turn, Side Adjust PC1 7-00040-701 SR522 Printed Circuit Board Q 1201 3-00026-325 2N5210 Transistor, TO-92 Package R 1001 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 1002 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1003 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1004 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1005 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 1006 4-00093-401 6.2K Resistor, Carbon Film, 1/4W, 5% R 1007 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 1008 4-00069-401 300K Resistor, Carbon Film, 1/4W, 5% R 1009 4-00046-401 2.0M Resistor, Carbon Film, 1/4W, 5% R 1010 4-00073-401 330K Resistor, Carbon Film, 1/4W, 5% R 1011 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1012 4-00138-407 10.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1013 4-00203-407 75.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1014 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1015 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 1016 4-00187-407 4.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1017 4-00160-407 2.26K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1018 4-00163-407 2.80K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1019 4-00084-401 5.1K Resistor, Carbon Film, 1/4W, 5% R 1020 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1021 4-00181-407 32.4K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1022 4-00132-407 1.10K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1023 4-00151-407 130K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1024 4-00156-407 16.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1025 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1026 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1027 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 1028 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1029 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 1030 4-00088-401 51K Resistor, Carbon Film, 1/4W, 5% R 1031 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 1032 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 1033 4-00030-401 10 Resistor, Carbon Film, 1/4W, 5% R 1034 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 1035 4-00033-404 100M Resistor, Carbon Comp, 1/4W, 5% R 1036 4-00187-407 4.53K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1037 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 1101 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1102 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1103 4-00085-401 5.1M Resistor, Carbon Film, 1/4W, 5% R 1104 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1105 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1106 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 1107 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1108 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

R 1109 4-00022-401 1.0M Resistor, Carbon Film, 1/4W, 5% R 1110 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1111 4-00193-407 499 Resistor, Metal Film, 1/8W, 1%, 50PPM R 1112 4-00217-408 1.000K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1113 4-00203-407 75.0K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1114 4-00080-401 47 Resistor, Carbon Film, 1/4W, 5% R 1115 4-00142-407 100K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1116 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1117 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 1118 4-00132-407 1.10K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1119 4-00179-407 30.1K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1120 4-00183-407 348K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1121 4-00155-407 150K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1122 4-00184-407 37.4K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1123 4-00212-407 9.76K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1124 4-00161-407 2.49K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1125 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1126 4-00045-401 2.0K Resistor, Carbon Film, 1/4W, 5% R 1127 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 1128 4-00131-407 1.00M Resistor, Metal Film, 1/8W, 1%, 50PPM R 1129 4-00146-407 110K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1130 4-00140-407 10.2K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1132 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1133 4-00021-401 1.0K Resistor, Carbon Film, 1/4W, 5% R 1201 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1202 4-00219-408 20.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1203 4-00218-408 10.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1204 4-00219-408 20.00K Resistor, Metal Film, 1/8W, 0.1%, 25ppm R 1205 4-00210-407 9.09K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1206 4-00130-407 1.00K Resistor, Metal Film, 1/8W, 1%, 50PPM R 1207 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1208 4-00032-401 100K Resistor, Carbon Film, 1/4W, 5% R 1209 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 1210 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% R 1211 4-00034-401 10K Resistor, Carbon Film, 1/4W, 5% R 1212 4-00057-401 220 Resistor, Carbon Film, 1/4W, 5% U 1001 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 1002 3-00072-340 CD4046 Integrated Circuit (Thru-hole Pkg) U 1003 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 1004 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 1005 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 1006 3-00066-340 CA3140E Integrated Circuit (Thru-hole Pkg) U 1007 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 1008 3-00066-340 CA3140E Integrated Circuit (Thru-hole Pkg) U 1009 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 1010 3-00093-340 LM13600 Integrated Circuit (Thru-hole Pkg) U 1011 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 1012 3-00094-340 LM311 Integrated Circuit (Thru-hole Pkg) U 1013 3-00068-340 CD4018 Integrated Circuit (Thru-hole Pkg) U 1014 3-00091-340 LF412 Integrated Circuit (Thru-hole Pkg) U 1101 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg)

SRS part# VALUE DESCRIPTION

SR530 COMPONENT PARTS LIST

REF.

U 1102 3-00091-340 LF412 Integrated Circuit (Thru-hole Pkg) U 1103 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 1104 3-00106-340 LT1007 Integrated Circuit (Thru-hole Pkg) U 1105 3-00074-340 CD4066 Integrated Circuit (Thru-hole Pkg) U 1106 3-00057-340 AD534 Integrated Circuit (Thru-hole Pkg) U 1107 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 1108 3-00106-340 LT1007 Integrated Circuit (Thru-hole Pkg) U 1109 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 1110 3-00084-340 ICL7650 Integrated Circuit (Thru-hole Pkg) U 1111 3-00126-335 51A05 Relay U 1112 3-00126-335 51A05 Relay U 1113 3-00126-335 51A05 Relay U 1114 3-00126-335 51A05 Relay U 1115 3-00126-335 51A05 Relay U 1116 3-00084-340 ICL7650 Integrated Circuit (Thru-hole Pkg) U 1117 3-00126-335 51A05 Relay U 1118 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 1119 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 1120 3-00088-340 LF353 Integrated Circuit (Thru-hole Pkg) U 1121 3-00035-340 74C74 Integrated Circuit (Thru-hole Pkg) U 1201 3-00058-340 AD7524 Integrated Circuit (Thru-hole Pkg) U 1202 3-00087-340 LF347 Integrated Circuit (Thru-hole Pkg) U 1203 3-00076-340 DG211 Integrated Circuit (Thru-hole Pkg) U 1204 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg) U 1205 3-00090-340 LF411 Integrated Circuit (Thru-hole Pkg)

SRS part# VALUE DESCRIPTION

Miscellaneous Parts List

REF. SRS part# VALUE DESCRIPTION

U 702 3-00161-342 27128-150 EPROM/PROM, I.C. Z 0 0-00045-013 4-40 MINI Nut, Mini Z 0 0-00078-031 4-40X1 M/F Standoff Z 0 0-00167-023 6-32X1/2RP Screw, Roundhead Phillips Z 0 0-00179-000 RIGHT FOOT Hardware, Misc. Z 0 0-00180-000 LEFT FOOT Hardware, Misc. Z 0 0-00185-021 6-32X3/8PP Screw, Panhead Phillips Z 0 0-00187-021 4-40X1/4PP Screw, Panhead Phillips Z 0 0-00204-000 REAR FOOT Hardware, Misc. Z 0 0-00209-021 4-40X3/8PP Screw, Panhead Phillips Z 0 0-00247-026 6-32X1/4 TRUSSP Screw, Black, All Types Z 0 0-00248-026 10-32X3/8TRUSSP Screw, Black, All Types Z 0 0-00371-026 4-40X3/16PF Screw, Black, All Types Z 0 6-00054-611 .375A 3AG Fuse Z 0 7-00147-720 BAIL Fabricated Part Z 0 7-00203-720 SR500-34 Fabricated Part Z 0 7-00204-720 SR500-35 Fabricated Part Z 0 7-00211-720 SR530-25 Fabricated Part Z 0 7-00215-720 SR530-29 Fabricated Part Z 0 7-00216-720 SR530-30 Fabricated Part

SR530 COMPONENT PARTS LIST

SRS Labs SR530 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual