SRAM MTB1 Users Manual

Power Meter User Manual
Statement of Compliance:
SRAM LLC. Model#: 0808 FCC ID: C9O-MERC1 IC: 10161A-MERC1
Model#: 0815 FCC ID: C9O-MTB1 IC: 10161A-MTB1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation.
Warning: Any changes or modications not expressively approved by SRAM could void the user's authority to operate this equipment.
Note: This equipement has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: 1 Reorient or relocate the receiving antenna. 2 Increase the separation between the equipment and receiver. 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4 Consult the dealer or an experienced radio/TV technician for help.
This product meets the applicable Industry Canada technical specications.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference that may cause undesired operation of the device.
The term “IC:” before the radio certication number only signies that Industry Canada technical specications were
met.
Statement of RoHS Compliance SRAM LLC. certies that this product and its packaging are in compliance with European Union Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronics Equipment, commonly known as RoHS.
ANT+ Product Certication
This product is ANT+ certied and complies with the bicycle power ANT+ Device Prole. For a complete listing of ANT+ Certied Products and their specic interoperability, please visit www.thisisant.com.
2
SRAM LLC WARRANTY
EXTENT OF LIMITED WARRANTY
Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials or workmanship for a period of two years after original purchase. This warranty only applies to the original owner and
is not transferable. Claims under this warranty must be made through the retailer where the bicycle or the SRAM component was purchased. Original proof of purchase is required. Except as described herein, SRAM makes
no other warranties, guaranties, or representations of any type (express or implied), and all warranties (including any implied warranties of reasonable care, merchantibility, or fitness for a particular purpose) are
hereby disclaimed.
LOCAL LAW
This warranty statement gives the customer specic legal rights. The customer may also have other rights which vary from state to state (USA), from province to province (Canada), and from country to country elsewhere in the
world.
To the extent that this warranty statement is inconsistent with the local law, this warranty shall be deemed modied
to be consistent with such law, under such local law, certain disclaimers and limitations of this warranty statement
may apply to the customer. For example, some states in the United States of America, as well as some governments outside of the United States (including provinces in Canada) may:
a. Preclude the disclaimers and limitations of this warranty statement from limiting the statutory rights of the
consumer
(e.g. United Kingdom).
b. Otherwise restrict the ability of a manufacturer to enforce such disclaimers or limitations.
For Australian customers:
This SRAM limited warranty is provided in Australia by SRAM LLC, 1333 North Kingsbury, 4th oor, Chicago, Illinois, 60642, USA. To make a warranty claim please contact the retailer from whom you purchased this SRAM product. Alternatively, you may make a claim by contacting SRAM Australia, 6 Marco Court, Rowville 3178, Australia. For valid claims SRAM will, at its option, either repair or replace your SRAM product. Any expenses incurred in making the warranty claim are your responsibility. The benets given by this warranty are additional to other rights and
remedies that you may have under laws relating to our products. Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
LIMITATIONS OF LIABILITY
To the extent allowed by local law, except for the obligations specically set forth in this warranty statement, in
no event shall SRAM or its third party suppliers be liable for direct, indirect, special, incidental, or consequential damages.
3
LIMITATIONS OF WARRANTY
This warranty does not apply to products that have been incorrectly installed and/or adjusted
according to the respective SRAM user manual. The SRAM user manuals can be found online at
sram.com, rockshox.com, avidbike.com, truvativ.com, or zipp.com.
This warranty does not apply to damage to the product caused by a crash, impact, abuse of the
product, non-compliance with manufacturers specications of usage or any other circumstances in
which the product has been subjected to forces or loads beyond its design.
This warranty does not apply when the product has been modied, including, but not limited to any
attempt to open or repair any electronic and electronic related components, including the motor,
controller, battery packs, wiring harnesses, switches, and chargers.
This warranty does not apply when the serial number or production code has been deliberately altered, defaced or removed.
This warranty does not apply to normal wear and tear. Wear and tear parts are subject to damage
as a result of normal use, failure to service according to SRAM recommendations and/or riding or
installation in conditions or applications other than recommended.
Wear and tear parts are identied as:
• Dust seals
• Bushings
• Air sealing o-rings
• Glide rings
• Rubber moving parts
• Foam rings
Rear shock mounting hardware and main seals
Upper tubes (stanchions)
Stripped threads/bolts
(aluminium, titanium, magnesium or steel)
Brake sleeves
Brake pads
• Chains
Sprockets
• Cassettes
Shifter and brake cables
(inner and outer)
• Handlebar grips
• Shifter grips
Jockey wheels
Disc brake rotors
Wheel braking surfaces
• Bottomout pads
• Bearings
• Bearing races
Pawls
• Transmission gears
Spokes
• Free hubs
• Aero bar pads
• Corrosion
• Tools
• Motors
• Batteries
Notwithstanding anything else set forth herein, the battery pack and charger warranty does not
include damage from power surges, use of improper charger, improper maintenance, or such other misuse.
This warranty shall not cover damages caused by the use of parts of different manufacturers. This warranty shall not cover damages caused by the use of parts that are not compatible, suitable
and/or authorised by SRAM for use with SRAM components. This warranty shall not cover damages resulting from commercial (rental) use.
4
Table of ConTenTs
TABLE OF CONTENTS
POWER METER ANATOMY ����������������������������������������������������������������������������������������6
INSTALLATION ������������������������������������������������������������������������������������������������������������� 7
MAGNET I NS TALL ATI ON �����������������������������������������������������������������������������������������������������������������������7 BB CUP MOUNT INSTALLATION ��������������������������������������������������������������������������������������������������������8 CABLE GUIDE MOUNT INSTALLATION �������������������������������������������������������������������������������������������9 ADHESIVE PUTTY INSTALLATION ��������������������������������������������������������������������������������������������������10
CRANK INSTALLATION ��������������������������������������������������������������������������������������������� 11
SET UP �������������������������������������������������������������������������������������������������������������������������� 11
LED FUNCTIONALITY ���������������������������������������������������������������������������������������������������������������������������� 11 PAIRING ������������������������������������������������������������������������������������������������������������������������������������������������������� 12 ZEROING ����������������������������������������������������������������������������������������������������������������������������������������������������� 12
CHAINRING INSTALLATION �������������������������������������������������������������������������������������14
MAINTENANCE AND CARE ���������������������������������������������������������������������������������������15
BAT TERY INF OR MATION ���������������������������������������������������������������������������������������������������������������������15 BATTERY CARE ���������������������������������������������������������������������������������������������������������������������������������������� 15 CLEANING �������������������������������������������������������������������������������������������������������������������������������������������������� 15
TROUBLESHOOTING ��������������������������������������������������������������������������������������������������16
5
Power meter AnAtomy
POWER METER ANATOMY
Crankarm Spider Serial
Number/ANT+ ID
Battery Compartment
LED
Cadence Sensor Ring
6
Cadence Sensor Ring Label
Loading...
+ 11 hidden pages