Squire Combi-Bolt 3 Fitting And Recoding Instructions

TM
GB
Fitting and Recoding Instructions
Combi-Bolt 3
NL
Installatie en coderingshandleiding
Combi-Bolt 3
Montage- und Codierungsanleitung
Combi-Bolt 3
TM
TM
TM
FR
Installation et instruction pour le codage.
Combi-Bolt 3
ES
Instrucciones de montaje y recodificación
Combi-Bolt 3
TM
TM
GB
Fitting and Recoding Instructions
Flush Fitting
Using the bolt and keep as a template
1.
mark the screw positions. Drill pilot holes for the screws. (Use 3.5mm drill bit).
Use the security screw provided and
2.
firmly screw into position. (Note these security screws cannot be undone).
Recess Fitting
After fitting the bolt use it to position
3.
the keep plate. Mark it's position and recess it into the frame.
4.
Drill the pilot holes as in 1. above and, using the security screws, secure the keep plate.
How to recode
(Where required)
Remove screw before recoding
0
00
Combi-Bolt 3
Once the screw has been removed draw the
2.
bolt back to its stop position. Lift the bolt knob and draw back to a second stop position. Push it down to lock it in this recoding position.
Carefully rotate the coding wheels to the
3.
desired number, taking care to align them to the coding mark. (Make a note of the new
code number).
Without moving the wheels reverse the procedure of 1. The new code is now set.
Put the security screw back.
4.
Remember
On external installations always lock the bolt even in the open position (This will prevent unauthorised recoding).
TM
TM
?
? ?
1.
The bolt is factory set on 000. Before you can recode the CombiBolt3 you need to remove the screw marked in the diagram above.
Henry Squire & Sons Limited
Hilton Cross Business Park, Cannock Road, Featherstone, Wolverhampton, WV10 7QZ
Tel: 01902 308050 Fax: 01902 308051
E-Mail: info@henry-squire.co.uk Website: www.squirelocks.co.uk
NL
Installatie en coderingshandleiding
Combi-Bolt 3
Installatie
Neem de bout en gebruik deze als model
1.
om de positie van de gaten aan te duiden. (gebruik een 3,5 mm boor)
2.
Gebruik de veiligheidsschroef en draai deze vast. (Let erop dat de schroeven goed vastzitten zodat ze er niet uit kunnen worden gedraaid)
Handleiding voor eventuele inbouw
Nadat het slot vastgezet is, gebruikt u de
3.
bout om de de plaat vast te zetten. Duid de positie aan en bevestig dit stuk aan het frame.
Maak gaten zoals in 1 en zet de plaat vast
4.
met de veiligheidsschroeven.
Hoe het slot coderen ?
Verwijder de schroef voor u begint met het slot te coderen
0
00
TM
TM
Als de schroef los gemaakt is, trekt u de bout
2.
terug naar de stoppositie. Hef de knop en trek de bout aan tot de tweede stoppositie. Druk de knop in om deze vast te zetten in de hercoderingspositie.
?
? ?
Draai voorzichtig aan de wielen tot u de
3.
gewenste code heeft. Let erop dat de wielen allemaal op een rechte lijn staan onder elkaar.
(noteer uw nieuwe code) Keer terug naar
punt 1, zonder de wielen/code te veranderen. De nieuwe code is nu ingesteld.
Plaats de veiligheidsschroef terug.
4.
Onthoud !
Bij outdoor gebruik van het slot, raden wij u aan het slot steeds te sluiten, ook bij open positie van het slot. (dit om misbruik van het slot te voorkomen)
1.
Standaard is het slot ingesteld op code
000. Voordat u het slot COMBIBOLT 3 kan hercoderen, verwijder dan eerst de schroeven zoals aangegeven in bovenstaand schema.
Henry Squire & Sons Limited
Hilton Cross Business Park, Cannock Road, Featherstone, Wolverhampton, WV10 7QZ
Tel: 01902 308050 Fax: 01902 308051
E-Mail: info@henry-squire.co.uk Website: www.squirelocks.co.uk
DE
Montage- und Codierungsanleitung
Combi-Bolt 3
Montage
Nutzen Sie den Bolzen und benutzen Sie ihn um
1.
die Positionen der Schrauben zu markieren. Bohren Sie mit einem 3,5mm Bohrer die Löcher.
Benutzen Sie die mitgelieferten
2.
Sicherheitssschrauben und schrauben Sie das Schloss in der Position fest. (Beachten Sie, dass die Sicherheitsschrauben nicht herausgedreht werden können)
stemmen Sie den Platz für die Aufnahme heraus, sofern dies notwendig ist
Nachdem das Bolzenschloss fixiert ist, benutzen
3.
Sie den Bolzen um die Gegenplatte zu positionieren. Markieren Sie Ihre Position it's position and recess it into the frame.
Bohren Sie die Löcher wie in !. beschrieben und
4.
nehmen Sie die Sicherheitsschrauben um die Gegenplatte zu fixieren.
Wie verändere ich den Zahlencode
Lösen Sie die Schrauben, bevor Sie mit dem Code-einstellen beginnen.
0
00
TM
TM
Wenn die Schraube gelöst ist, zeiehn Sie den Bolzen
2.
bis in die Stopposition zurück. Heben Sie den Knopf an und ziehen Sie den Bolzen bis zu einer zweiten Stopposition. Drücken Sie den Knopf runter, um den Bolzenn in der Codierungsposition zu arretieren.
?
? ?
Drehen Sie die Zahlenscheiben vorsichtig auf die
3.
gewünschten Zahlen und richten Sie diese exakt and der Einstellmarkierung aus. Notieren Sie die neue Zahlencombination.
Führen Sie nun die Bolzenbewegungen (Pos.1.) in umgekehrter Reihenfolge aus, ohne den Zahlencode zu verdrehen. Der neue Code ist nun eingestellt.
Montieren Sie die Sicherheitsschrauben
4.
Achtung
Bei Montage in Außenbereichen solltenn Sie das Schloß immer abschließen, auch wenn das Tor offen ist. (dann kann nicht versehentlich ein neuer Code eingestellt werden)
Der Zahlencode is fabrikseitig auf 000
1.
eingestellt. Bevor Sie beim Combibolt 3 einen neuen Code einstellen können, müssen Sie die im obigen Diagramm gezeigte Schraube lösen.
Henry Squire & Sons Limited
Hilton Cross Business Park, Cannock Road, Featherstone, Wolverhampton, WV10 7QZ
Tel: 01902 308050 Fax: 01902 308051
E-Mail: info@henry-squire.co.uk Website: www.squirelocks.co.uk
FR
Installation et instruction pour le codage.
Combi-Bolt 3
Installation
Retirez le boulon et utilisez le comme
1.
modèle pour indiquer la position des trous. (Utiliser une méche de 3,5 mm).
Utilisez la vis de sécurité fournie et la serrez
2.
fermement. (Noter que la vis ne peut plus être déserrée)
Montage d'encastrement (si nécessaire)
Après le montage, utilisez le boulon pour
3.
positionner la plaque de maintien. Marquez la position et fixez la dans le cadre.
Faites les trous comme dans 1 ci-dessus et, à
4.
l'aide des vis de sécurité, fixez la plaque de maintien.
Comment recoder
Enlevez la vis avant de recoder
0
00
TM
TM
Une fois que la vis a été retirée, visez le bolon
2.
jusqu'à sa position d'arrêt. Soulevez le bouton de verrou et reculez jusqu'à une seconde position d'arrêt. Poussez-le vers le bas pour le verrouiller dans la position recodage.
?
? ?
Faites tourner soigneusement les roues de
3.
codage au nombre souhaité, en prenant soin de les aligner sur la marque de codage. (Notez le
nouveau numéro de code). Sans déplacer les
roues inversent la procédure ou 1. Le nouveau code est maintenant réglé.
Remettez la vis de sécurité en place.
4.
Avertissement
Sur les installations extérieures, verrouillez toujours le boulon même en position ouverte (Ceci pour prevenir un recodage non autorisé).
1.
Le boulon est réglé en usine sur 000. Avant de pouvoir recoder le CombiBolt3 vous devez retirer la vis indiquée dans le schéma ci-dessus.
Henry Squire & Sons Limited
Hilton Cross Business Park, Cannock Road, Featherstone, Wolverhampton, WV10 7QZ
Tel: 01902 308050 Fax: 01902 308051
E-Mail: info@henry-squire.co.uk Website: www.squirelocks.co.uk
ES
TM
Instrucciones de montaje y recodificación
TM
?
? ?
Montaje
Usa el pasador y mantener como una plantilla
1.
marque las posiciones del tornillo. Perfore los agujeros piloto para los tornillos. (Utilice una broca de 3,5 mm).
Utilice el tornillo de seguridad suministrado y
2.
atorníllelo firmemente en su posición. (Tenga en cuenta que estos tornillos de seguridad no se pueden deshacer).
Encage
Después de montar el pasador, úselo para
3.
colocar la placa de retención. Marque su posición y empújela en el marco.
Taladre los orificios guía como antes. arriba y,
4.
usando los tornillos de seguridad, asegure la placa de retención.
Cómo recodificar
Retire el tornillo antes de recodificarlo
0
00
Combi-Bolt 3
Una vez que el tornillo ha sido retirado, extraiga el
2.
pasador de nuevo a su posición de parada. Levante la perilla del pasador y retroceda a una segunda posición de parada. Empuje hacia abajo para bloquearlo en esta posición de recodificación.
Gire cuidadosamente las ruedas de codificación
3.
hasta el número deseado, teniendo cuidado de alinearlas con la marca de codificación. (Anote el
nuevo número de código).
Sin mover las ruedas, invierta el procedimiento de nuevo. El nuevo código ya está ajustado.
Vuelva a colocar el tornillo de seguridad.
4.
Recordar
En las instalaciones externas siempre bloquee el pasador incluso en posición abierta (Esto evitará la recodificación no autorizada).
El pasador está ajustado de fábrica en 000.
1.
Antes de recodificar el CombiBolt3 debe quitar el tornillo marcado en el diagrama anterior.
Henry Squire & Sons Limited
Hilton Cross Business Park, Cannock Road, Featherstone, Wolverhampton, WV10 7QZ
Tel: 01902 308050 Fax: 01902 308051
E-Mail: info@henry-squire.co.uk Website: www.squirelocks.co.uk
Loading...