Square Scrub EBG-28, EBG-20/C, EBG-20/Q, EBG-20/E, EBG-20/R Owner's Manual
...
EBG Series
Surface Preparation
Machines
Owner’s
Manual
EBG-20/C
www.squarescrub.com / 800.557.6822
EBG-20/Q•EBG-20/C•EBG-20/E
EBG-28•EBG-20/R•EBG-28/R
EBG-28
®
®
Introduction
You are now the proud owner of an EBG-Series machine. This machine is a product of Square Scrub
Inc. It is made of ne materials and will give you many years of satisfactory service if maintained
and used according to the guidelines in this owner’s manual.
Please read all Installation, Operation, and Safety Instructions before using this
machine.
This product is for Industrial/Institutional/Commercial Use Only.
WARNING OF POTENTIAL INJURY!
MOVING PARTS! UNPLUG BEFORE SERVICING!
This product contains moving parts. To reduce the risk of injury, unplug before servicing.
General Safety
- This oor-nishing machine shall be grounded while in use to protect the operator from electric
shock. The machine is provided with a three-conductor cord and a three-contact grounding type
attachment plug to t the proper grounding type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Never connect this wire to anything other than the
grounding pin of the attachment plug.
- This machine is for use on a nominal 120-volt circuit and has a grounding plug that resembles the
plug in gure 1. Make sure that the machine is connected to an outlet having the same
conguration as the plug.
No adapter should be used with this machine.
page 2
gure 1
Square Scrub EBG Series
Surface Preparation Machines
Owner’s Manual
Contents
• Introduction
• Manual Conventions
• Safety / Important
• Machine Transport
• Operating Instructions
• Troubleshooting Guide
• Parts Breakdown
• Warranty Information
• Pad Information
About the Square Scrub
Floor Surface Preparation Machine
Square Scrub’s EBG machines are American Made. Our EBG Surface Preparation machines offer
removable weights, a minimum 1.5hp, 1725rpm motor, powder coated 10 gauge steel, heavy
duty frame, and 6”x2” non-marking ball-bearing wheels with a heavy duty ¾” solid steel axle.
Removable weights not only make our machine easy to transport but allow users to tailor the
weight to suit their project needs.
With a selection of over 30 different surface preparation pads, there really is only one machine
for the job. The Square Scrub EBG Surface Preparation Machines are designed to make the most
efcient use of every pad, paper or screen used with the machine, saving both time and MONEY.
Please visit our Web site at
www.squarescrub.com for
informative videos and
literature.
EBG-20/Q
page 1
page 4
Important
• Never leave the machine unattended while power cord is connected.
• Do not operate this machine while under the inuence of alcohol or
other drugs.
• Never allow children under age 18 to operate this machine.
• Unplug machine from power source before adjusting height of handle
or changing pad.
• Always wear personal protective equipment (PPE) when operating this
machine.
• Never inhale dust created by the use of this machine. Any modications to this machine may
result in damage to the machine or injury to the operator or others nearby. Alterations to the
machine will also void any and all warranty and liabilities.
• Sanding wood decks is not recommended by Square Scrub due to uneven surfaces which could
lead to damage to the machine. Some pressure treated wood found in decking contains arsenic
that, when sanded, will create hazardous dust. Square Scrub assumes no liability if the machine
is used on decks, and damage caused from sanding pressure treated wood will not be warranted.
• Do not operate this machine around fuels, solvents, ammable oor nishes, thinners, wood
particulate or any ammable materials. Cigarette lighters, pilot lights, electrical sparks and all
other sources of ignition should be extinguished or avoided. Work areas should be well
ventilated.
• Keep the power cord clear of the pad. Always lift the cord over the machine. Do not pull on the
power cord in an attempt to move the machine. This could result in electrocution. Operating this
machine with a damaged power cord could lead to electrocution or re. Cord should remain clear
of moving parts during operation. Never use the cord to navigate the machine. If the supply
cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
• Servicing this machine while still connected to a power source could lead to electrocution or re.
Before performing machine service or maintenance, disconnect the machine from it’s power
source.
• Do not use machine if it has been sprayed with water or left out in the rain. This could result in a
shock injury or electrocution.
• Keep feet, hands, and loose clothing away from any moving parts on the machine to avoid injury.
Disconnect power cord before changing the pad or when servicing. Damage can occur to the
machine or to other property if instructions in the owner’s manual are not followed.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
Warning: This appliance is not suitable for picking up hazardous dust.
PPE Equipment
Sound Power Level:
120V:
max 85dBA measured. Avg. around 78dBA
240V:
max 81dBA measured, Avg. 75dBA
Vibration Total:
120V:
Avg. 6.8 mm/s
2
, max at 7.0 mm/s
2
240V:
Avg. 2.8 mm/s2, max at 3.0 mm/s
2
Manual Conventions
Danger: Indicates an imminently hazardous situation which, if not avoided, may result
in death or serious injury.
Caution: Indicates that machine or property damage could result if instructions are not
followed.
Note: Provides helpful information.
Severe bodily injury or death can occur to you or other personnel if warnings
found on this machine or in this owner’s manual are ignored. Read and observe all
statements and instructions found on the machine and in the owner’s manual.
Who to call for assistance
If you work with a Square Scrub-authorized distributor, contact them for assistance.
If any contents of the box are missing, contact your Square Scrub-authorized dealer, distributor or reseller. If you
purchased your machine directly from Square Scrub, contact Square Scrub at 1.800.557.6822 for service in the United
States and Canada. For worldwide service, call Square Scrub directly at 870.930.9898. Make sure you have the machine’s serial number, located on the back of the machine, when you call.
Liability statement
This Square Scrub product has been built to the highest industry standards. Please note and heed the WARNING and
CAUTION labels that have been placed on the equipment and in this manual for your safety. PLEASE DO NOT ATTEMPT
TO OPERATE OR REPAIR THIS EQUIPMENT WITHOUT ADEQUATE TRAINING. ANY USE, OPERATION OR REPAIR IN
CONTRAVENTION OF THIS DOCUMENT IS AT YOUR OWN RISK. BY ACCEPTANCE OF THIS SYSTEM YOU HEREBY ASSUME ALL
LIABILITY CONSEQUENT TO YOUR USE OR MISUSE OF THIS EQUIPMENT. SQUARE SCRUB SHALL NOT BE LIABLE FOR ANY
INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGE OF ANY KIND.
Equipment specications, applications and options are subject to
change at the sole discretion of Square Scrub without notice.
Safety
All Square Scrub products are built to strict safety and reliability
specications in accordance with industry standards. Therefore,
safety issues pertaining to operation and repair of Square Scrub
equipment are primarily environmental and human interface. The
following basic safety tips are given to ensure safe installation,
operation and maintenance of Square Scrub.
page 3
EBG-20/E
Loading...