Squareled BLADE 5 User Manual

User Manual: Squareled Blade 5 48x10W RGBW

BLADE 5

48x10W - RGBW

USER MANUAL

1

INTRODUCTION

Thank you for having chosen our LED lighting
Unpack the device, inside the box you should find:
The fixture device
One power cable
One XLR connection cable
This manual
Please check carefully that there is no damage caused by
transportation. Should there be any problems, consult your dealer and
don’t install this device.

DESCRIPTION

Features

 Easy multi fixture hanging system, outdoor version available
 48pcs RGBW 4in1 LED, no ultraviolet radiation
 More than 20,000 hours for the LED light source
 15,000 lm
 35 degrees
 1/2/3/4/6/8F/9F/10F/10D/14D/15F DMX channels
 16 Bit Dimmer
 DMX Mode /Master-slave mode
 AC 100-240V 50/60Hz 500W
 Diecasting heatsink with fans control, convection cooling, With

temperature sensor to extend the lamp life

 7000 Hz LED scan rate
 L: 490mm H: 313mm W: 144mm

 IP65

SAFETY INSTRUCTIONS

This device has left the factory in perfect condition. In order to
maintain this condition and to ensure a safe operation, it

is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.

This device falls under protection-class I. Therefore it is essential that

2

the device should be earthed.
The electric connection must carry out by qualified person.
If the external flexible cable or cord of this luminaire is damaged,
it shall be exclusively replaced by the manufacturer or his
service agent or a similar qualified person in order to avoid a hazard.

Make sure that the available voltage is not higher than stated at the
end of this manual.

Make sure the power cord is never crimped or damaged by sharp
edges.
If this would be the case, replacement of the cable must be done by
an authorized dealer.

Always disconnect from the mains, when the device is not in use or
before cleaning it. Only handle the power cord by the plug. Never
pull out the plug by tugging the power cord.

Never look directly into the light source, as
sensitive persons may suffer an epileptic shock.

Important:
Damages caused by the disregard of this user manual are not
subject to warranty. The dealer will not accept liability for any
resulting defects or problems.

DMX-512 control connection

The product has a DMX 512 input fitted with 3-pin XLR connectors.
Screened cables in compliance with EIA RS-485 specifications and the
following characteristics must be used for connections:

- 2 conductors plus screen

- 120Ohm impedance

- low capacitance

- max. transmission rate 250kBaud.

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is

3

in an electrically noisy environment, such as in a discotheque, it is
recommended to use a DMX terminator. This helps in preventing
corruption of the digital control signal by electrical noise. The DMX

terminator is simply an XLR plug with a 120 OHM resistor connected

between pins 2 and 3,which is then plugged into the output XLR
socket of the last fixture in the chain.

Display Menu

Main menu

Sub-menu

Address

DMX Address Setting

Config.

Channel Mode

Channel 1Ch

Channel 2Ch

Channel 3Ch

Channel 4Ch

Channel 6Ch

Channel 8ChF

Channel 9ChF

Channel 10ChF

Channel 10ChD

Channel 14ChD

Channel 15ChF

Dimmer Curve

Set Curve Mode L

Set Curve Mode Q

Set Curve Mode I

Set Curve Mode S

Cipher Setup

0-999

4

Temp Unit CS

Celsius Degree

Fahrenheit Degree

DMX Status

Value Clear

Value Hold

Fan Speed

Normal/ middle/ fast

WDMX Mode

-

Display Mode

Disable

Enable

System Info

Temperature

Fixture Time

Color Menu

Red

0-255

Green

0-255

Blue

0-255

White

0-255

White Balance

Set Red

0-255

Set Green

0-255

Set Blue

0-255

Static color

Color 0-51

-

Auto Test

Effect Auto 01

-

Effect Auto 02

-

Effect Auto 03

-

Effect Auto 04

-

Fan Test

Fan 1

On/ Off

Auto speed

00 - 40

Load Default

Yes

No

Firmware

Version

Strobe Wash

Version 6.00

5

Main functions

1. Address: Current DMX address
A. Setting DMX address by button

press ENTER button when show the address menu, then adjust
the DMX address by pressing [UP] or [DOWN] button
Press [ENTER] to confirm or press [ESC] to return to main menu.

B. Setting DMX address by controller

1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26,

channel 7 to 30-36,channel 8 to 40-46,then the devices
connected to the controller will enter to the setting address mode

2. Set the DMX value of channel 1 from 0-59,then you will see
the first number of the Address change to (channel 1 value)/10.
For example, when set the value of channel 1 to 20,the first DMX
address number will be 2(20/10=2),

3. Set the DMX value of channel 2 from 0-99,then you will see
the second number of the Address change to (channel 2
value)/10.
For example, when set the value of channel 2 to 30,the first DMX
address number will be 2(30/10=3),

4.Set the DMX value of channel 3 from 0-99,then you will see the
third number of the Address change to (channel 3 value)/10.
For example, when set the value of channel 1 to 40,the first DMX
address number will be 3(40/10=4),
And the DMX address you set by controller will be 234.

5. Set the DMX value of channel 4 to 255,then you will save the
DMX address settled by the controller.

Caution: It won’t save the address if the address number is

over 512

6. set the value of channel 5-8 out of the value range show on the

step 1,and the device will exit the setting address mode

2. Config.
Setting DMX mode

press ENTER button when show the channel menu, then select
the DMX mode by pressing [UP] or [DOWN] button

6

Setting Dimmer Curve

press ENTER button when show the dimmer curve menu, then
select the dimmer curve by pressing [UP] or [DOWN] button

Setting Cipher

press ENTER button when show the cipher setup menu, then
setup cipher by pressing [UP] or [DOWN] button

Key mode

press ENTER button when show the key mode menu, then
select lock or unlock by pressing [UP] or [DOWN] button

Show Temperature

press ENTER button when show the Temp Unit CS menu, select
the way of showing the fixture’s temperature in ℃ or ℉ by
pressing [UP] or [DOWN] button

DMX status

press ENTER button when show the DMX Status menu, then
select clear value or hold value by pressing [UP] or [DOWN]
button

Display mode

press ENTER button when show the Display Mode menu, then
select auto or on by pressing [UP] or [DOWN] button

3. System info
Temperature

press ENTER button when show the Temperature menu, then it
will show the temperature of the fixture

Fixture time

press ENTER button when show the Fixture time menu, then it
will show how long time of the fixture already used

4. Color menu

press ENTER button when show the Color menu, press Enter
button to select the color mode, then adjust the color by pressing

[UP] or [DOWN] button

5. White balance

7

press ENTER button when show the white balance menu, press
Enter button to select the color mode, then adjust the color by
pressing [UP] or [DOWN] button

6. Auto test

press ENTER button when show the auto test menu, select test
mode by pressing [UP] or [DOWN] button

DMX functions and values

1 ch Mode

Ch

Value

Function 1 0-255

Static Color

2 ch Mode

Ch

Value

Function

1

0-7

8-15

16-151

152-175

175-199

200-244

245-255

Blackout

Shutter Open

Strobe

Fade In

Fade Out

Random Strobe

Shutter Open

2

0-255

Master Dimmer

3 ch Mode

Ch

Value

Function 1 0-255

Red 2 0-255

Green

3

0-255

Blue

4 ch Mode

8

Ch

Value

Function 1 0-255

Red 2 0-255

Green 3 0-255

Blue 4 0-255

White

6 Ch Mode

Ch

Value

Function

1

0-7

8-15

16-151

152-175

175-199

200-244

245-255

Blackout

Shutter Open

Strobe

Fade In

Fade Out

Random Strobe

Shutter Open

2

0-255

Master dim

3

0-255

Red 4 0-255

Green 5 0-255

Blue 6 0-255

White

8 ChF Mode

Ch

Value

Function 1 0-255

Red

2

0-255

Fine Red

3

0-255

Green 4 0-255

Fine Green

5

0-255

Blue

6

0-255

Fine Blue 7 0-255

White 8 0-255

Fine White

9

9 ChF Mode

Ch

Value

Function 1 0-255

Master Dimmer

2

0-255

Red 3 0-255

Fine Red 4 0-255

Green 5 0-255

Fine Green

6

0-255

Blue 7 0-255

Fine Blue 8 0-255

White 9 0-255

Fine White

10 ChF Mode 16BIT

Ch

Value

Function

1

0-255

Master Dimmer

2

0-255

Fine Master Dimmer

3

0-255

Red 4 0-255

Red dimmer fine

5

0-255

Green 6 0-255

Green dimmer fine

7

0-255

Blue 8 0-255

Blue dimmer fine

9

0-255

White

10

0-255

White dimmer fine

10 ChD Mode

Ch

Value

Function

1

0-7

8-15

16-151

152-175

Blackout

Shutter Open

Strobe

Fade In

10

175-199

200-244

245-255

Fade Out

Random Strobe

Shutter Open

2

0-255

Master dim

3

0-255

Red1 4 0-255

Green1 5 0-255

Blue1

6

0-255

White1 7 0-255

Red2 8 0-255

Green2 9 0-255

Blue2

10

0-255

White2

14 ChD Mode

Ch

Value

Function

1

0-255

Master Dimmer

2

0-255

Red1 3 0-255

Green1

4

0-255

Blue1 5 0-255

White1 6 0-255

Red2 7 0-255

Green2 8 0-255

Blue2 9 0-255

White2

10

0-15

16-255

Shutter Open
Strobe From Slow To Fast

11

0-35

36-71

72-107
108-143
144-179
180-215
216-255

Shutter Open
Fade Out
Fade In
Fade In and Out
Fade By SIN Curve
Four Color Flow
Eight LEDs Flow

12

0-255

Static Color

13

0-255

Dimmer Speed

11

14

0-63

64-127

128-191

192-255

Linear

Square

Invert Square

S-Curve

15 ChF Mode

Ch

Value

Function

1

0-255

Master Dimmer

2

0-255

Fine Master Dimmer

3

0-255

Red1 4 0-255

Green1 5 0-255

Blue1 6 0-255

White1 7 0-255

Red2 8 0-255

Green2 9 0-255

Blue2

10

0-255

White2

11

0-15

16-255

Shutter Open
Strobe From Slow To Fast

12

0-35

36-71

72-107
108-143
144-179
180-215
216-255

Shutter Open
Fade Out
Fade In
Fade In and Out
Fade By SIN Curve
Four Color Flow
Eight LEDs Flow

13

0-255

Static Color

14

0-255

Dimmer Speed

15

0-63

64-127

128-191

192-255

Linear

Square

Invert Square

S-Curve

12

CLEANING AND MAINTENANCE

We recommend a frequent cleaning of the device. Please use a soft
lint-free and moistened cloth. Never use alcohol or solvents!

CAUTION!

Disconnect from mains before starting maintenance

operation.

There are no serviceable parts inside the device. Maintenance and
service operations are only to be carried out by authorized dealers.
If you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to
be replaced by authorized dealers only in order to avoid hazards.
If you have further questions, please contact your dealer.

INSTALLATION

The device must only be installed at a vibration-free, oscillation-free
and fire-resistant location.

Das Lichttechnikhaus Vertriebs GmbH

Rudolf-Diesel-Str. 3, D-89312 Günzburg
Telefon [phone]

Fax [phone]
E-Mail [e-mail]
Web www.lth-gmbh.de