Square D LC2D12F7 Data Sheet

Product data sheet

Characteristics

LC2D12F7

REVERSING CONTACTOR 575VAC 12A IEC

Main

Range of product TeSys D

Range TeSys

Product name TeSys D

Product or component type Reversing contactor

Device short name LC2D

Contactor application Resistive load

Utilisation category AC-1

Device presentation Preassembled with reversing power busbar

Poles description 3P

Pole contact composition 3 NO

[Ue] rated operational voltage <= 300 V DC for power circuit

[Ie] rated operational current 12 A (<= 60 °C) at <= 440 V AC AC-3 for power circuit

Motor power kW 3 kW at 220...230 V AC 50/60 Hz

Motor power hp 1 hp at 115 V AC 50/60 Hz for 1 phase motors

Control circuit type AC 50/60 Hz

[Uc] control circuit voltage 110 V AC 50/60 Hz

Auxiliary contact composition 1 NO + 1 NC

[Uimp] rated impulse withstand voltage 6 kV conforming to IEC 60947

Overvoltage category III

Motor control

AC-3

<= 690 V AC 25...400 Hz for power circuit

25 A (<= 60 °C) at <= 440 V AC AC-1 for power circuit

7.5 kW at 500 V AC 50/60 Hz

7.5 kW at 660...690 V AC 50/60 Hz

5.5 kW at 380...400 V AC 50/60 Hz

5.5 kW at 415...440 V AC 50/60 Hz

2 hp at 230/240 V AC 50/60 Hz for 1 phase motors
3 hp at 200/208 V AC 50/60 Hz for 3 phases motors
3 hp at 230/240 V AC 50/60 Hz for 3 phases motors

7.5 hp at 460/480 V AC 50/60 Hz for 3 phases motors
10 hp at 575/600 V AC 50/60 Hz for 3 phases motors

Sep 22, 2017

Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications

1

[Ith] conventional free air thermal
current

Irms rated making capacity 250 A at 440 V for power circuit conforming to IEC 60947

Rated breaking capacity 250 A at 440 V for power circuit conforming to IEC 60947

[Icw] rated short-time withstand current 105 A <= 40 °C 10 s power circuit

Associated fuse rating 25 A gG at <= 690 V coordination type 2 for power circuit

Average impedance 2.5 mOhm at 50 Hz - Ith 25 A for power circuit

[Ui] rated insulation voltage 600 V for power circuit certifications CSA

Electrical durability 2 Mcycles 12 A AC-3 at Ue <= 440 V

Power dissipation per pole 0.36 W AC-3

Protective cover With

Interlocking type Mechanical

Mounting support Rail

Standards CSA C22.2 No 14

Product certifications LROS (Lloyds register of shipping)

Connections - terminals Control circuit : screw clamp terminals 2 cable(s) 1...2.5 mm² - cable stiffness: flexible - with cable

Tightening torque Power circuit : 1.7 N.m - on screw clamp terminals - with screwdriver flat Ø 6 mm

Operating time 4...19 ms opening

25 A at <= 60 °C for power circuit
10 A at <= 60 °C for signalling circuit

140 A AC for signalling circuit conforming to IEC 60947-5-1
250 A DC for signalling circuit conforming to IEC 60947-5-1

210 A <= 40 °C 1 s power circuit
30 A <= 40 °C 10 min power circuit
61 A <= 40 °C 1 min power circuit
100 A 1 s signalling circuit
120 A 500 ms signalling circuit
140 A 100 ms signalling circuit

40 A gG at <= 690 V coordination type 1 for power circuit
10 A gG for signalling circuit conforming to IEC 60947-5-1

600 V for power circuit certifications UL
690 V for power circuit conforming to IEC 60947-4-1
690 V for signalling circuit conforming to IEC 60947-1
600 V for signalling circuit certifications CSA
600 V for signalling circuit certifications UL

0.8 Mcycles 25 A AC-1 at Ue <= 440 V

1.56 W AC-1

Plate

EN 60947-4-1
EN 60947-5-1
IEC 60947-4-1
IEC 60947-5-1
UL 508

GL
UL
CSA
DNV
RINA
CCC
BV
GOST

end
Power circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: flexible - with cable end
Control circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: flexible - without cable
end
Control circuit : screw clamp terminals 2 cable(s) 1...4 mm² - cable stiffness: flexible - without cable
end
Control circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: flexible - with cable end
Control circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: solid - without cable end
Control circuit : screw clamp terminals 2 cable(s) 1...4 mm² - cable stiffness: solid - without cable end
Power circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: flexible - without cable
end
Power circuit : screw clamp terminals 2 cable(s) 1...4 mm² - cable stiffness: flexible - without cable
end
Power circuit : screw clamp terminals 2 cable(s) 1...2.5 mm² - cable stiffness: flexible - with cable end
Power circuit : screw clamp terminals 1 cable(s) 1...4 mm² - cable stiffness: solid - without cable end
Power circuit : screw clamp terminals 2 cable(s) 1...4 mm² - cable stiffness: solid - without cable end

Power circuit : 1.7 N.m - on screw clamp terminals - with screwdriver Philips No 2
Control circuit : 1.7 N.m - on screw clamp terminals - with screwdriver flat Ø 6 mm
Control circuit : 1.7 N.m - on screw clamp terminals - with screwdriver Philips No 2

12...22 ms closing

2

Safety reliability level B10d = 1369863 cycles contactor with nominal load conforming to EN/ISO 13849-1

Mechanical durability 15 Mcycles

Operating rate 3600 cyc/h at <= 60 °C

B10d = 20000000 cycles contactor with mechanical load conforming to EN/ISO 13849-1

Complementary

Coil technology Without built-in suppressor module

Control circuit voltage limits 0.3...0.6 Uc drop-out at 60 °C, AC 50/60 Hz

Inrush power in VA 70 VA at 20 °C (cos ϕ 0.75) 60 Hz

Hold-in power consumption in VA 7.5 VA at 20 °C (cos ϕ 0.3) 60 Hz

Heat dissipation 2...3 W at 50/60 Hz

Auxiliary contacts type Type mechanically linked (1 NO + 1 NC) conforming to IEC 60947-5-1

Signalling circuit frequency 25...400 Hz

Minimum switching current 5 mA for signalling circuit

Minimum switching voltage 17 V Signalling circuit

Non-overlap time 1.5 ms on de-energisation (between NC and NO contact)

Insulation resistance > 10 MOhm for signalling circuit

Power range 2.2...3 kW 200...240 V 3 phases

Motor starter type Reversing contactor

Contactor coil voltage 110 V AC standard

0.8...1.1 Uc operational at 60 °C, AC 50 Hz

0.85...1.1 Uc operational at 60 °C, AC 60 Hz

70 VA at 20 °C (cos ϕ 0.75) 50 Hz

7 VA at 20 °C (cos ϕ 0.3) 50 Hz

Type mirror contact (1 NC) conforming to IEC 60947-4-1

1.5 ms on energisation (between NC and NO contact)

4...6 kW 380...440 V 3 phases

4...6 kW 480...500 V 3 phases

Environment

IP degree of protection IP20 front face conforming to IEC 60529

Protective treatment TH conforming to IEC 60068-2-30

Pollution degree 3

Ambient air temperature for operation -20...60 °C

Ambient air temperature for storage -60...80 °C

Permissible ambient air temperature
around the device

Operating altitude 3000 m without derating in temperature

Fire resistance 850 °C conforming to IEC 60695-2-1

Flame retardance V1 conforming to UL 94

Mechanical robustness Vibrations contactor open 2 Gn, 5...300 Hz

Height 77 mm

Width 90 mm

Depth 86 mm

Product weight 0.697 kg

-40...70 °C at Uc

Vibrations contactor closed 4 Gn, 5...300 Hz
Shocks contactor open 10 Gn for 11 ms
Shocks contactor closed 15 Gn for 11 ms

Offer Sustainability

Sustainable offer status Green Premium product

RoHS (date code: YYWW) Compliant - since 0627 - Schneider Electric declaration of conformity

Schneider Electric declaration of conformity

REACh Reference not containing SVHC above the threshold

Reference not containing SVHC above the threshold

Product environmental profile Available

3

Product environmental

Product end of life instructions Available

End of life manual

Contractual warranty

Warranty period 18 months

4

Product data sheet

Dimensions Drawings

Dimensions

LC2D12F7

LC2 or 2 x LC1 a b

D09 to D18 (AC) 90 77 86 4 1.5 80

D093 to D123 (AC) 90 99 86 – – 80

D09 to D18 (DC) 90 77 95 4 1.5 80

D093 to D123 (DC) 90 99 95 – – 80

D25 to D38 (AC) 90 85 92 9 5 80

D183 to D383 (AC) 90 99 92 – – 80

D25 to D32 (DC) 90 85 101 9 5 80

D183 to D383 (DC) 90 99 101 – – 80

e1 and e2: including cabling.

(1) With safety cover, without add-on block.

(1)

c

e1 e2 G

5

Product data sheet

Connections and Schema

Wiring

LC2D12F7

6

Product data sheet

LC2D12F7

Motor Starter BOM

Our Proposal - Type 1 : Circuit Breaker + Contactor for Motor Power 5,5 kW and 415 VAC

Motor power

(kW)

5.5 15

Non contractual pictures.

Type 1 coordination requires that in a short-circuit condition, the contactor or starter must not present any danger to personnel or installations and
must not be able to resume operation without repair or the replacement of parts.

ICU

(kA)

Breaker Contactor (*)

GV2ME16 LC2D12F7

7