Product data sheet
Characteristics
ATS48M10Y
soft starter for asynchronous motor - ATS48 - 954
A - 208..690 V - 250..900 KW
Main
Range of product Altistart 48
Product or component type Soft starter
Product destination Asynchronous motors
Product specific application Severe and standard applications
Pumping and ventilation machine
Device short name ATS48
[Us] rated supply voltage 208...690 V (- 15...10 %)
Motor power kW 220 kW at 230 V for severe applications
250 kW at 230 V for standard applications
400 kW at 400 V for severe applications
500 kW at 400 V for standard applications
500 kW at 440 V for severe applications
500 kW at 500 V for severe applications
500 kW at 525 V for severe applications
630 kW at 440 V for standard applications
630 kW at 500 V for standard applications
630 kW at 525 V for standard applications
710 kW at 660 V for severe applications
710 kW at 690 V for severe applications
900 kW at 660 V for standard applications
900 kW at 690 V for standard applications
Motor power hp 1000 hp at 575 V for standard applications
250 hp at 208 V for severe applications
300 hp at 230 V for severe applications
350 hp at 208 V for standard applications
350 hp at 230 V for standard applications
600 hp at 460 V for severe applications
800 hp at 460 V for standard applications
800 hp at 575 V for severe applications
Power dissipation in W For standard applications 2225 W
For standard applications 2865 W
Utilisation category AC-53A
Type of start Start with torque control (current limited to 5 In)
IcL starter rating 1000 A for standard applications
790 A for standard applications
May 26, 2017
Disclaimer: This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications
1
IP degree of protection IP00
Complementary
Assembly style With heat sink
Function available External bypass (optional)
Supply voltage limits 177...759 V
Supply frequency 50...60 Hz (- 5...5 %)
Network frequency 47.5...63 Hz
Device connection In the motor supply line
Factory setting current 954 A
Control circuit voltage 110 - 15 % to 230 + 10 %, 50/60 Hz
Control circuit consumption 80 W
Discrete output number 2
Discrete output type (LO1) logic output 0 V common configurable
Output absolute accuracy precision +/- 5 %
Minimum switching current Relay outputs 10 mA at 6 V DC
Maximum switching current Logic output 0.2 A at 30 V DC
Discrete input number 5
Discrete input type PTC, 750 Ohm at 25 °C
Discrete input voltage 24 V (<= 30 V)
Discrete input logic (Stop, Run, LI3, LI4) positive logic state 0 < 5 V and <= 2 mA, state 1 > 11 V and >= 5 mA
Supply inrush current Adjustable 0.4...1.3 Icl
Analogue output type (AO) current output 0-20 mA or 4-20 mA <= 500 Ohm
Communication port protocol Modbus
Connector type 1 RJ45
Communication data link Serial
Physical interface RS485 multidrop
Transmission rate 4800, 9600 or 19200 bps
Installed device 31
Protection type Phase failure (line)
Marking CE
Type of cooling Forced convection
Operating position Vertical +/- 10 degree
Height 890 mm
Width 770 mm
Depth 315 mm
Product weight 115 kg
(LO2) logic output 0 V common configurable
(R1) relay outputs fault relay NO
(R2) relay outputs end of starting relay NO
(R3) relay outputs motor powered NO
Relay outputs 1.8 A at 230 V AC inductive load, cos phi = 0.5, L/R = 20 ms
Relay outputs 1.8 A at 30 V DC inductive load, cos phi = 0.5, L/R = 20 ms
(Stop, Run, LI3, LI4) logic, <= 8 mA 4300 Ohm
Thermal protection (motor)
Thermal protection (starter)
Environment
Electromagnetic compatibility Conducted and radiated emissions conforming to IEC 60947-4-2 level A
Standards EN/IEC 60947-4-2
Product certifications TCF
2
Damped oscillating waves conforming to IEC 61000-4-12 level 3
Electrostatic discharge conforming to IEC 61000-4-2 level 3
Immunity to electrical transients conforming to IEC 61000-4-4 level 4
Immunity to radiated radio-electrical interference conforming to IEC 61000-4-3 level 3
Voltage/Current impulse conforming to IEC 61000-4-5 level 3
DNV
CSA
UL
C-Tick
CCC
SEPRO
GOST
NOM 117
Vibration resistance 1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6
Shock resistance 15 gn for 11 ms conforming to EN/IEC 60068-2-27
Noise level 60 dB
Pollution degree Level 3 conforming to IEC 60664-1
Relative humidity <= 95 % without condensation or dripping water conforming to EN/IEC 60068-2-3
Ambient air temperature for operation -10...40 °C without derating
Ambient air temperature for storage -25...70 °C
Operating altitude <= 1000 m without derating
1.5 mm (f = 2...13 Hz) conforming to EN/IEC 60068-2-6
> 40...60 °C with current derating of 2 % per °C
> 1000...2000 m with current derating of 2.2 % per additional 100 m
Contractual warranty
Warranty period 18 months
3
Loading...