Page 1
TL-X SEMI-AUTO
CAUTION
• This paintball marker is NOT a toy. It can cause serious injury
or death.
• Recommend at least 18 years of age to purchase this product.
• Install a barrel plug in the barrel when not actually playing.
• All persons using this product, or within range while this product is
being used, must wear eye and face protection specifically designed
for paintball.
• Never shoot a person who is not wearing proper protection.
• Treat every paintball marker as if it were loaded.
• Never look down the barrel of the marker.
• Keep the paintball marker on safe until ready to shoot.
• Always remove gas source before disassembly.
• Fire only 0.68 caliber paintballs from this product.
• Read this manual and air system warning before using this product.
• Transfer this instruction manual upon change of marker ownership.
IMPORTANT
• Firing velocity may vary according to altitude and climate conditions.
• BEFORE using your marker in play, you must always first perform a “SAFE VELOCITY TEST”. This can only be accomplished
by using a testing device called a “Velocity Chronograph” and can be performed by the dealership where you purchased this
product or at a local paintball playing field.
• Note: This product is intended to be used at a velocity no greater than 300 feet per second (FPS).
• Recommended velocity is 280 FPS or less.
• This product is NOT intended to be used at any distance less than 25 feet.
• This paintball marker may have excess gas after removal of the tank. Please remove all paintballs and discharge the
remaining gas safely.
r
e
d
y
p
s
CO2/HP AIR TANK WARNING
WARNING
• VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED
PERSONNEL.
• BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR
RETEST DATE!
• Improper use, filling, storage or disposal of this cylinder may result in
death, personal injury and property damage.
• This cylinder must be filled only by properly Trained personnel in
accordance with CGA Pamphlets P.1 and G-6.3 available from the
Compressed Gas Association WWW.CGANET.COM
• Do not over pressurize. Do not expose pressurized cylinder to
temperatures in excess of 130 degrees F.
• Do not expose cylinder to corrosive materials and do not clean with
caustic cleaners.
• Do not alter this cylinder in any way.
• Cylinders heated to a temperature of 250 degrees F or more must be
condemned or requalified in accordance with test defined in CFR-49.
• Keep cylinder out of reach of children.
• The valve should NEVER be detached from the canister. Should this
occur, please seek assistance from a trained airsmith immediately.
• This tank is intended for paintball use only.
SPYDER TL-X
ITEM # Name of Parts
01
Spyder Barrel Plug
1002F
12" Barrel (Silver)
04GA
Ball Stopper w/Detent Cover
05B
M4 x 6 Screw (Silver)
28041
Direct Feed (Silver)
28061
Receiver (Blue)
28081
Vertical Adapter (Blue)
28082
Low Pressure Chamber (Silver)
07
M5 x 14 Screw w/ Washer
09
O-Ring #015 80D
10A
Valve Spring
11
Cup Seal Guide
12
Cup Seal
13
Valve Pin
ITEM # Name of Parts
14
15
16
RF17
1717A
1717B
1717C
18B
19A
20
21
22
23B
23C
Valve Body
Valve Body Screw
M5 x 12 Screw (Black)
Venturi Bolt
Retaining Screw
Retaining Spring
Retaining Bearing
Striker Bolt (#19A)
Striker O-Ring
Barrel O-Ring (Black)
Bolt Pin
M4 X 8 Screw (Black)
Quick Disconnect Pin
Disconnect Pin Lock
2808228082
280822808228082
0101
010101
2020
202020
1002F1002F
1002F1002F1002F
2808128081
280812808128081
0909
090909
ITEM # Name of Parts
23FA
28291
10A10A
10A10A10A
1111 1212 1313
111111 121212 131313
0909 0909
090909 090909
0909
090909
2844128441
284412844128441
37C37C
37C37C37C
2844228442
284422844228442
37J37J 37D37D 37A37A 37B37B
37J37J37J 37D37D37D 37A37A37A 37B37B37B
Striker Bolt Plug (Silver)
25
Striker Spring
26A
Striker Buffer
27
Striker Spring Guide
27A
Flat Disc
29B
Lock Screw
Thumb Adjuster w/ screw (Blue)
42F42F
42F42F42F
37C
0909 0909
090909 090909
33C33C
33C33C33C
33C33C
33C33C33C
04GA04GA
04GA04GA04GA
05B05B
05B05B05B
05B05B
05B05B05B
1414
141414
2804128041
280412804128041
0707
070707
05B05B
05B05B05B
2806128061
280612806128061
1515
151515
38A38A
38A38A38A
58145814
581458145814
1616
161616
32E32E
32E32E32E
r
r
de
de
y
y
sp
sp
31B31B
31B31B31B
4848
484848
4949 4949
494949 494949
33F33F
33F33F33F
RF39RF39
RF39RF39RF39
49A49A
49A49A49A
2831128311
283112831128311
23C23C
23C23C23C
23B23B
23B23B23B
19A19A
19A19A19A
1616
161616
18B18B
18B18B18B
2829128291
0909 0909 2222
090909 090909 222222
RF17RF17
RF17RF17RF17
26A26A2525
26A26A26A252525
23FA23FA
23FA23FA23FA
2121
212121
27A27A
27A27A27A
1717B1717B
1717B1717B1717B
1717A1717A
1717C1717C
1717C1717C1717C
2727
272727
29B29B
29B29B29B
2829128291
282912829128291
1717A1717A1717A
KINGMAN Warranty Registration
PLEASE COMPLETE AND RETURN THIS FORM, ALONG WITH A COPY OF YOUR PURCHASE
RECEIPT, WITHIN 15 DAYS OF PURCHASE SO THAT WE MAY VALIDATE YOUR ONE YEAR
LIMITED WARRANTY.
Mail to: Kingman Group
14010 Live Oak Avenue
Baldwin Park, CA 91706 U.S.A.
Name Telephone ( )
Address
City State Zip Country
Your age E-mail address Occupation
33F33F
2835128351
283512835128351
33F33F33F
Product name and model
What other brand(s) of markers do you own?
Why did you purchase this Kingman marker?
ITEM # Name of Parts
36D
5/32" x 5/8" Screw
36E
5/32" x 7/8" Screw (Black)
37A
Filter O-Ring
37B
Air Filter
37C
Disconnect O-Ring #011(Black)
37D
Plastic Washer
37J
Disconnect Hose
2841
Spare Parts Kit
28441
Gas Thru Fore Grip (Silver)
28442
Mini Fore Grip (Blue)
38A
Safety Button Set (Medium)
RF39
Cocking Knob (Blue)
42F
Male to Male Metric Adapter
48
Trigger Roll Pin
49
Sear Roll Pin
49A
Secondary Sear Roll Pin
5814
Double Trigger
Avg # of times you play paintball per month
What is the next paintball product you intend to buy?
What are your hobbies (other than paintball)?
What are some magazines you like to read?
Have you purchased products from the Internet within the last 6 months?
Comments/Suggestions:
2835
36E36E36E36E
36E36E36E36E36E36E
ITEM # Name of Parts
31B
Trigger Sear
28311
Deluxe Trigger Frame
32E
45 Grip Cover
33C
Grip Cover Screws (M3 x 10)
33F
Nut Screw
2835
C/A Adapter (Blue)
28351
Deluxe Drop Forward (Silver)
36D36D36D36D
36D36D36D36D36D36D
WARRANTY STATEMENT
Kingman warranties to the original customer purchaser that this product is free from defects in
material and workmanship under normal use and service for a period of 12 months from the
original date of purchase by the initial owner/purchaser. For warranty to be effective, customer
must return the enclosed warranty registration card, along with a copy of the purchase receipt,
within fifteen days of purchase. Kingman agrees to repair or replace (at its discretion) any product
within a reasonable period of time. This warranty does not cover o-rings, scratches, nicks,
normal wear and tear of parts, any modifications or normal fading of anodizing or damage caused
by dropping or hitting of products. This warranty shall not apply if it is shown by Kingman that the
consumer caused the defect or malfunction because of misuse. This warranty only covers original
factory parts. Any modifications or tampering of original factory parts will not be covered by this
warranty. Any damage caused by water will not be covered by this warranty. Warranty work can
only be conducted by Kingman technician or Kingman authorized technicians. If product needs
repair, package it carefully and send together with your name, address, phone number and a brief
description of the malfunction to:
14010 Live Oak Avenue, Baldwin Park, CA 91706
Telephone: 626.430.2300 Fax: 626.851.8530
Website: www.Kingman.com
TROUBLESHOOTING
ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED PROBLEMS:
a. The pressure in the tank is too low or too high.
b. Need lubrication. (See OPERATION GUIDE in P4)
c. #19A (striker o-ring) is damaged. Replace with new Kingman or Kingman-approved o-ring.
(Note: the #19A O-ring cannot be substituted by a tank o-ring or a #9 o-ring).
d. Need to clean barrel and upper chamber or the receiver.
e. Paintball may be defective (i.e. expired, change shape)
f. #9 (bolt o-ring) is damaged or the o-ring has expanded or swelled. Replace with a
new o-ring.
g. After ball breaks, remove all parts from UPPER chamber of receiver, wipe parts clean, and
reassemble parts into receiver. Also make sure to clean barrel with squeegee
HELPFUL HINTS
• Always remove air tank before any disassembly of your marker. DO NOT remove #14
(valve body) unless specific valve body repairs are needed. If needed, remove valve body
with a long, soft-tipped object such as the eraser end of a pencil. DO NOT remove the valve
body with a screwdriver as it will damage the valve body and cause air leaks. (Note: #15
screw must be removed prior to taking out the valve body).
• Air leaks are usually cause by a damaged valve body or damaged cup seal (#12). Replace
with new valve body and/or cup seal if necessary.
• To assure marker is assembled properly, follow the schematic drawing or place parts in
order during disassembly. Parts assembled backwards or placed in the wrong order will
cause marker to malfunction.
+
SPYDER TL-X OPERATION GUIDE:
1. To put the marker on “SAFE”, push the safety from the “PUSH SAFE” side of the trigger frame.
To disengage the safety, point the marker in safe direction, push in the safety from
the “PUSH FIRE” side of the trigger frame.
2. Cock the marker by pulling the Cocking Bolt (#RF39) rearward until it latches.
Caution: if you let go before it latches, your marker may fire.
3. Tighten the air tank until it is snug. If a leak occurs between the air tank and the C/A Adapter,
replace the tank o-ring.
4. Install a 7/8” elbow with loader into the vertical feed. Fill the loader with .68 caliber paintballs only.
5. With the safety off, fire the marker by pulling the trigger.
6. Only use lubrication specifically designed for paintball markers. To lubricate your marker, you will
need to disassemble your marker (please note how parts are removed from marker as this will
ease reassembly). Remove the Disconnect Lock Pin (#23C) and the Disconnect Pin (#23B). Hold
down the Striker Plug (#23FA) and Thumb Adjuster (#28291), as internal parts may be springloaded. As you pull the cocking knob out of the receiver, the Cocking Bolt (#RF17) and Striker
(#18B) will also be removed.
7. Lubricate o-rings #9 and #19A with a few drops of paintball oil only.
8. Reassemble parts back into the marker. Note: when putting the Cocking Bolt and Striker back
into the marker, you will need to apply pressure behind the bolt while pulling the trigger at the
same time. This will allow the Bolt and Striker to be properly installed back into the receiver.
9. When you are finished shooting the marker, first, unload the marker of all paintballs. Note: there
may be a ball in the receiver; take a couple of shots in a safe direction to make sure that the
barrel and receiver are empty. Second, put the barrel plug into the barrel. Put the safety on and
slowly unscrew the air source tank. Caution: do not unscrew the tank valve from the tank. Doing
so may cause serious injury or death.
10. Empty the hopper or remove the hopper off the marker to stop the flow of paintballs in the marker.
+
Loading...