SPT SPT7935SIT Datasheet
SPT7935
12-BIT, 20 MSPS, 79 mW A/D CONVERTER
FEATURES
• 12-Bit, 20 MSPS Analog-to-Digital Converter
• Monolithic CMOS
• Internal Track-and-Hold
• Low Input Capacitance: 1.4 pF
• Low Power Dissipation: 79 mW
• 2.8 – 3.6 V Power Supply Range
• TTL-Compatible Outputs
GENERAL DESCRIPTION
The SPT7935 12-bit, 20 MSPS analog-to-digital converter
has a pipelined converter architecture built in a CMOS
process. It delivers high performance with a typical power
dissipation of only 79 mW. With low distortion and high
dynamic range, this device offers the performance needed
BLOCK DIAGRAM
APPLICATIONS
• CCD Imaging Cameras and Sensors
• Medical Imaging
• RF Communications
• Document and Film Scanners
• Electro-Optics
• Transient Signal Analysis
• Handheld Equipment
for imaging, multimedia, telecommunications and instrumentation applications.
The SPT7935 is available in a 44-lead Thin Quad Flat Pack
(TQFP) package in the industrial temperature range (–40 to
+85 °C).
–
G=2
Stage
10
2-Bit
ADC
V
V
VIN+
V
IN
REF
REF
CLK
DACADC +
D<1…0> Pipeline Stage
–
+
–
Clock
Driver
Stage
1
Stage
2
Digital Delays, Error Correction and Output
Digital Output (D0 – D11)
Stage
9
12
Signal Processing Technologies, Inc.
4755 Forge Road, Colorado Springs, Colorado 80907, USA
Phone: (719) 528-2300 FAX: (719) 528-2370 Website: http://www.spt.com E-Mail: sales@spt.com
ABSOLUTE MAXIMUM RATINGS (Beyond which damage may occur)1 25 °C
Supply Voltages
V
....................................................................
DD
1
V
....................................................................
DD
2
V
....................................................................
DD
3
–0.5 V to +6 V
–0.5 V to +6 V
–0.5 V to +6 V
Temperature
Operating Temperature ............................. –40 to +85 °C
Storage Temperature............................... –65 to +125 °C
Input Voltages
Analog Input.................................–0.5 V to (VDD +0.5 V)
Digital Input .................................. –0.5 V to (VDD +0.5 V)
V
+ .......................................... –0.5 V to (VDD +0.5 V)
REF
V
– .......................................... –0.5 V to (VDD +0.5 V)
REF
CLK .............................................. –0.5 V to (VDD +0.5 V)
Note: 1. Operation at any Absolute Maximum Rating is not
implied. See Electrical Specifications for proper
nominal applied conditions in typical applications.
ELECTRICAL SPECIFICATIONS
TA=T
MIN–TMAX
Bias 2=9.5 µA, Differential Input, Duty Cycle=50%, unless otherwise specified.
PARAMETERS CONDITIONS LEVEL MIN TYP MAX UNITS
DC Accuracy
Resolution 12 Bits
Differential Linearity V ±0.6 LSB
Integral Linearity V ±3.0 LSB
No Missing Codes VI Guaranteed
Analog Input
Input Voltage Range (Differential) IV ±0.6 ±1.0 ±1.7 V
Common Mode Input Voltage IV 1.2 1.65 1.9 V
Input Capacitance V 1.4 pF
Input Bandwidth (Large Signal) V 120 MHz
Offset (Mid-scale) VIN+=VIN–=V
Gain Error V 0.3 % FSR
Reference Voltages
Reference Input Voltage Range IV 0.6 1.0 1.7 V
Negative Reference Voltage (V
Positive Reference Voltage (V
Common Mode Output Voltage (VCM)IO = –1 µA VI 1.3 1.65 1.8 V
V
REF
V
REF
Switching Performance
Maximum Conversion Rate VI 20 MHz
Pipeline Delay IV 7.5 Clocks
(See Timing Diagram)
Aperture Delay Time (T
Aperture Jitter Time V 10 ps-rms
Dynamic Performance
Effective Number of Bits
Signal-To-Noise Ratio
Total Harmonic Distortion
, V
=V
=V
DD
2
=3.3 V, V
DD
3
DD
1
–=1.0 V, V
REF
+=2.0 V, Common Mode Voltage=1.65 V, ƒ
REF
=20 MSPS, Bias 1=90 µA,
CLK
TEST TEST SPT7935
V ±1.0 % FSR
(V
REF
+ – V
REF
–)
CM
–) IV 0.9 1.0 1.3 V
REF
+) IV 1.9 2.0 2.6 V
REF
+ Current V 35 µA
– Current V –25 µA
)V5ns
AP
ƒ
= 5.0 MHz VI 9.2 9.8 Bits
IN
ƒIN = 10.0 MHz V 9.0 Bits
ƒIN = 5.0 MHz VI 59 62 dB
ƒIN = 10.0 MHz V 58 dB
ƒ
= 5.0 MHz VI –68 –61 dB
IN
ƒ
= 10.0 MHz V –60 dB
IN
SPT
SPT7935
2 7/12/00
ELECTRICAL SPECIFICATIONS
TA=T
MIN–TMAX
Bias 2=9.5 µA, Differential Input, Duty Cycle=50%, unless otherwise specified.
, V
DD
=V
=V
2
=3.3 V, V
DD
3
DD
1
–=1.0 V, V
REF
+=2.0 V, Common Mode Voltage=1.65 V, ƒ
REF
=20 MSPS, Bias 1=90 µA,
CLK
TEST TEST SPT7935
PARAMETERS CONDITIONS LEVEL MIN TYP MAX UNITS
Dynamic Performance–Continued
Signal-To-Noise and Distortion
ƒ
= 5 MHz VI 57 61 dB
IN
ƒIN = 10 MHz V 56 dB
Spurious Free Dynamic Range
ƒIN = 5.0 MHz VI 62 70 dB
ƒIN = 10.0 MHz V 61 dB
Differential Phase V 0.2 Degrees
Differential Gain V 0.5 %
Digital Inputs
Logic 1 Voltage VI 80% V
Logic 0 Voltage VI 20% V
DD
DD
Maximum Input Current Low VIN = GND VI ±1 µA
Maximum Input Current High V
IN
= V
DD
VI ±1 µA
Input Capacitance V 1.8 pF
Digital Outputs
Logic 1 Voltage I
= -2 mA VI 85% V
O
DD
95% V
DD
V
Logic 0 Voltage IO = +2 mA VI 0.1 0.4 V
CLK to Output Delay Time (tD)IV4812ns
Power Supply Requirements
Supply Voltages
V
, V
DD1
DD2
, V
DD3
IV 2.8 3.3 3.6 V
Supply Current
I
DD
VI 24 30 mA
Power Dissipation VI 79 100 mW
Power Supply Rejection Ratio (PSRR) V 67 dB
TEST LEVEL CODES
All electrical characteristics are subject to the
following conditions: All parameters having
min/max specifications are guaranteed. The
Test Level column indicates the specific
device testing actually performed during production and Quality Assurance inspection.
Any blank section in the data column indicates that the specification is not tested at the
specified condition.
TEST LEVEL
I
II
III
IV
V
VI
TEST PROCEDURE
100% production tested at the specified temperature.
100% production tested at TA = +25 °C, and sample tested at
the specified temperatures.
QA sample tested only at the specified temperatures.
Parameter is guaranteed (but not tested) by design and
characterization data.
Parameter is a typical value for information purposes only.
100% production tested at TA = +25 °C. Parameter is guaran-
teed over specified temperature range.
SPT
SPT7935
3 7/12/00
Loading...