SPT SPT7860SCT Datasheet

SPT7860

10-BIT, 40 MSPS, 175 mW A/D CONVERTER

TECHNICAL DATA

MAY 25, 2001

FEATURES

• Monolithic 40 MSPS converter

• 175 mW power dissipation

• On-chip track-and-hold

• Single +5 V power supply

• TTL/CMOS outputs

• 5 pF input capacitance

• Low cost

• Tr i-state output buffers

• High ESD protection: 3,500 V minimum

• Selectable +3 V or +5 V logic I/O

GENERAL DESCRIPTION

The SPT7860 is a 10-bit monolithic, low-cost, ultralow­power analog-to-digital converter capable of minimum
word rates of 40 MSPS. The on-chip track-and-hold func­tion assures very good dynamic performance without the
need for external components. The input drive require­ments are minimized due to the SPT7860’s low input
capacitance of only 5 pF.

Po wer dissipation is e xtremely lo w at only 175 mW typical
at 40 MSPS with a power supply of +5.0 V. The digital out­puts are +3 V or +5 V, and are user selectable. The

APPLICATIONS

• All high-speed applications where low power
dissipation is required

• Video imaging

• Medical imaging

• Radar receivers

• IR imaging

• Digital communications

SPT7860 is pin-compatible with the entire family of SPT
10-bit, CMOS converters (SPT7835/40/50/55/60/61),
which simplifies upgrades. The SPT7860 has incorpo­rated proprietary circuit design* and CMOS processing
technologies to achieve its adv anced perf ormance. Inputs
and outputs are TTL/CMOS-compatible to interface with
TTL/CMOS logic systems. Output data format is straight
binary.

The SPT7860 is available in 28-lead SOIC and 32-lead
small (7 mm square) TQFP packages over the commer­cial temperature range.

*Patent pending

BLOCK DIAGRAM

A

IN

CLK In

Enable

Data
Valid

Ref

In

Timing

and

Control

1:16
Mux

P1

P2

.

.

.

P15

P16

ADC Section 1

T/H

ADC Section 2

.
.
.

ADC Section 15

ADC Section 16

T/H

Auto-

Zero

CMP

Auto-

Zero

CMP

Reference Ladder

11-Bit

SAR

DAC

11-Bit

SAR

DAC

11

11

11

.
.
.

11

V

REF

.
.
.

11

11

11-Bit

16:1
Mux/
Error

Correction

Signal Processing Technologies, Inc.

4755 Forge Road, Colorado Springs, Colorado 80907, USA

Phone: [phone] Fax: [phone] Web Site: http://www .spt.com e-mail: [e-mail]

D10 Overrange

D9 (MSB)

D8

D7

D6

D5

D4

D3

D2

D1

D0 (LSB)

ABSOLUTE MAXIMUM RATINGS (Beyond which damage may occur)1 25 °C

Supply Voltages

AVDD......................................................................+6 V

Output

Digital Outputs ...................................................10 mA

DVDD.....................................................................+6 V

Temperature

Input Voltages

Analog Input .............................. –0.5 V to AVDD +0.5 V

..............................................................0 to AV

V

REF

CLK Input ............................................................... V

AVDD – DVDD..................................................±100 mV

AGND – DGND ..............................................±100 mV

DD
DD

Operating Temperature ................................ 0 to 70 °C

Junction Temperature ........................................ 175 °C

Lead Temperature, (soldering 10 seconds) ....... 300 °C

Storage Temperature............................ –65 to +150 °C

Note: 1. Operation at any Absolute Maximum Rating is not implied. See

Electrical Specifications for proper nominal applied conditions
in typical applications.

ELECTRICAL SPECIFICATIONS

TA=T

to T

MIN

, AVDD=DVDD=OVDD=+5.0 V , VIN=0 to 4 V, ƒS=40 MSPS, V

MAX

TEST TEST SPT7860

PARAMETERS CONDITIONS LEVEL MIN TYP MAX UNITS
Resolution 10 Bits
DC Accuracy

Integral Linearity Error (ILE) VI ±1.0 LSB
Differential Linearity Error (DLE) VI ±0.5 LSB
No Missing Codes VI Guaranteed

Analog Input

Input Voltage Range VI V
Input Resistance IV 50 kΩ
Input Capacitance V 5.0 pF
Input Bandwidth (Small Signal) V 250 MHz
Offset V ±2.0 LSB
Gain Error V ±2.0 LSB

RHS

=4.0 V , V

=0.0 V, unless otherwise specified.

RLS

RLS

V

RHS

V

Reference Input

Resistance VI 300 500 600 Ω
Bandwidth V 100 150 MHz
Voltage Range

IV 0 2.0 V
IV 3.0 AV

DD

V 1.0 4.0 5.0 V

V

∆(V
∆(V

V
V
V

RLS
RHS

RHS
RHF
RLS

– V

RLS

– V

)V90mV

RHS

– V

)V75mV

RLF

Reference Settling Time

V

RHS

V

RLS

V 15 Clock Cycles
V 20 Clock Cycles

Conversion Characteristics

Maximum Conversion Rate VI 40 MHz
Minimum Conversion Rate IV 2 MHz
Pipeline Delay (Latency) IV 12 Clock Cycles
Aperture Delay Time V 4.0 ns
Aperture Jitter Time V 30 ps (p-p)

Dynamic Performance

Effective Number of Bits (ENOB)

= 3.58 MHz VI 8.5 Bits

ƒ

IN

= 10.3 MHz VI 8.3 Bits

ƒ

IN

Signal-to-Noise Ratio (SNR)
(without Harmonics)

= 3.58 MHz VI 52 54 dB

ƒ

IN

ƒIN = 10.3 MHz VI 51 52 dB

SPT

SPT7860

2 5/25/01

ELECTRICAL SPECIFICATIONS

TA=T

to T

MIN

, AVDD=DVDD=OVDD=+5.0 V , VIN=0 to 4 V, ƒS=40 MSPS, V

MAX

TEST TEST SPT7860

PARAMETERS CONDITIONS LEVEL MIN TYP MAX UNITS
Dynamic Performance

Total Harmonic Distor tion (THD) 9 Distor tion bins from

= 3.58 MHz 1024 pt FFT VI 55 61 dB

ƒ

IN

= 10.3 MHz VI 52 53 dB

ƒ

IN

Signal-to-Noise and Distortion

(SINAD)

= 3.58 MHz VI 51 54 dB

ƒ

IN

ƒ

= 10.3 MHz VI 49 52 dB

IN

Spurious Free Dynamic Range ƒ

= 1 MHz V 63 dB

IN

Differential Phase V ±0.3 Degree
Differential Gain V ±0.3 %

Inputs

Logic 1 Voltage VI 2. 0 V
Logic 0 Voltage VI 0.8 V
Maximum Input Current Low VI –10 +10 µA
Maximum Input Current High VI –10 +10 µA
Input Capacitance VI +5 pF

Digital Outputs

Logic 1 Voltage IOH = 0.5 mA VI 3. 5 V
Logic 0 Voltage I
t

RISE

t

FALL

Output Enable to Data Output Delay 20 pF load, T

= 1.6 mA VI 0.4 V

OL

15 pF load V 10 ns
15 pF load V 10 ns

= +25 °CV 10 ns

A

50 pF load over temp. V 22 ns

RHS

=4.0 V , V

=0.0 V, unless otherwise specified.

RLS

Power Supply Requirements

Voltages OV

DV
AV

Currents AI

DI

DD
DD
DD

DD

DD

IV 3.0 5.0 V
IV 4.75 5.0 5.25 V
IV 4.75 5.0 5.25 V
VI 17 22 mA
VI 18 23 mA

Power Dissipation VI 175 225 m W

TEST LEVEL CODES

All electrical characteristics are subject to the
following conditions:

All parameters having min/max specifications
are guaranteed. The Test Level column indi­cates the specific device testing actually per­formed during production and Quality Assur­ance inspection. Any blank section in the data
column indicates that the specification is not
tested at the specified condition.

LEVEL TEST PROCEDURE

I 100% production tested at the specified temperature.

II 100% production tested at TA = +25 °C, and sample tested at the

specified temperatures.
III QA sample tested only at the specified temperatures.
IV Parameter is guaranteed (but not tested) by design and characteri-

zation data.

V Parameter is a typical value for information pur poses only.

VI 100% production tested at TA = +25 °C. Parameter is guaranteed

over specified temperature range.

SPT

SPT7860

3 5/25/01

SPECIFICATION DEFINITIONS

APERTURE DELAY

Aperture delay represents the point in time, relative to the
rising edge of the CLOCK input, that the analog input is
sampled.

APERTURE JITTER

The variations in aperture delay for successive samples.

DIFFERENTIAL GAIN (DG)

A signal consisting of a sine wave superimposed on vari­ous DC levels is applied to the input. Diff erential gain is the
maximum variation in the sampled sine wave amplitudes
at these DC levels.

DIFFERENTIAL PHASE (DP)

A signal consisting of a sine wave superimposed on vari­ous DC levels is applied to the input. Differential phase is
the maximum variation in the sampled sine wave phases
at these DC levels .

EFFECTIVE NUMBER OF BITS (ENOB)

SINAD = 6.02N + 1.76, where N is equal to the effective
number of bits.

INPUT BANDWIDTH

SINAD – 1.76

N =

6.02

INTEGRAL LINEARITY ERROR (ILE)

Linearity error refers to the deviation of each individual
code (normalized) from a straight line drawn from –FS
through +FS. The deviation is measured from the edge of
each particular code to the true straight line.

OUTPUT DELAY

Time between the clock’s triggering edge and output data
valid.

OVERVOLTAGE RECOVERY TIME

The time required for the ADC to recover to full accuracy
after an analog input signal 125% of full scale is reduced
to 50% of the full-scale value.

SIGNAL-TO-NOISE RATIO (SNR)

The ratio of the fundamental sinusoid power to the total
noise power. Harmonics are excluded.

SIGNAL-TO-NOISE AND DISTORTION (SINAD)

The ratio of the fundamental sinusoid power to the total
noise and distortion power.

TOTAL HARMONIC DISTORTION (THD)

The ratio of the total power of the first 9 harmonics to the
power of the measured sinusoidal signal.

Small signal (50 mV) bandwidth (3 dB) of analog input
stage.

DIFFERENTIAL LINEARITY ERROR (DLE)

Error in the width of each code from its theoretical value.
(Theoretical = VFS/2N)

SPURIOUS FREE DYNAMIC RANGE (SFDR)

The ratio of the fundamental sinusoidal amplitude to the
single largest harmonic or spurious signal.

SPT

SPT7860

4 5/25/01