Sprint Nextel Spectrum Dual Keypad User Manual

TO USE THE CALL DISPLAY FEATURE OF THIS PHONE, YOU MUST SUBSCRIBE TO CALLDISPLAYSERVICE, AND REMEMBER TO INST ALL
BATTERIES
NOTE: PLEASE READ AND FOLLOW THESE INSTRUCTIONS BEFORE
USING YOUR TELEPHONE
13 MEMORY CALLER DISPLAY TRIM PHONE MODEL 2012J OPERATING INSTRUCTIONS
LOCA TION OF CONTROLS ............................................... 1
GETTING ST ARTED ........................................................... 2
CHECKING THE PACKAGE CONTENTS .............................. 2
TELEPHONE INSTALLATION ................................................ 2
SETTING UP THE TELEPHONE ........................................... 4
MAKING AND RECEIVING CALLS .................................... 6
MEMORYDIALING ............................................................. 7
CALL DISPLAY FEATURES ............................................... 8
WALLMOUNTING .............................................................12
TROUBLE SHOOTING ......................................................14
BATTERY SAFETY INSTRUCTIONS ................................17
LOCATION OF CONTROLS
1
18
1
2
4
3
5
6
7
8
9
10
11
12 13 14
15
16
17
19
20
21
1. MUTE
2. RESET
3. STORE (Memory)
4. MEMO (Memory)
5. ONE-TOUCH SPEED DIAL (M1, M2 & M3)
6. HOOK SWITCH
7. VOLUME CONTROL
8. TONE/PULSE SWITCH
9. REDIAL
10. FLASH
11. HANDSET CORD JACK
12. LINE CORD JACK (on bottom)
13. RINGER (HI/LOW/OFF) SWITCH
14. TELEPHONE NUMBER INDEX
15. BATTERY COMPARTMENT
16. CALL BACK
17. DELETE
18. DOWN
19. UP
20. CALL DISPLAY
21. NEW CALL INDICATOR
GETTING STARTED
Step 1: Checking the Package Contents
Your new 2012 Call Display Trim Phone has all the features of a 13 memory telephone plus Call Display functionality. As you unpack this set, make sure you have the following items in the package.
Step 2: Telephone Installation INSTALLING BATTERIES
Before you connect the phone cords, follow these steps to install the batteries:
1. Push down the battery door tab with a pen or other pointed object and lift the battery door out (Fig. 1).
2. Insert 3 size "AA" alkaline batteries as shown inside the battery compartment. (The negative side of the battery touches the bat­tery spring.)
2
3. Replace the battery door and snap it shut (Fig. 2).
CAUTION
Make sure that the telephone line cord is disconnected before opening the battery door. Replace the batteries when the LOW BATTERY INDICATOR
appears in the display or when the display gets dim.
‹ When the batteries are dead, the display will not show. You
can still make or receive calls, but you cannot use the Call Display or memory dialing.
‹ When the batteries are dead, your call data and memories
could be erased.
CONNECTING THE TELEPHONE
1. Connect the COILED HANDSET CORD to the bottom of the handset and the bot­tom of the base.
2. Connect the straight telephone line cord to the LINE CORD jack and telephone outlet on the wall .
3. Route the LINE CORD into the channel on the bottom of the base.
(For instructions on how to mount the telephone on the wall, see page 12.)
3
LOW
Step 3: Setting up the Telephone SETTING UP LANGUAGE, AREA CODE, TIME AND DATE
You may need to set up the language, area code, time and date for your telephone when you install the batteries for the first time or when you move to an area that has a different area code. This is necessary because the phone must dis­tinguish local or long distance calls to properly dial calls from the Call Display list.
NOTE: During setup, if you do not press the DELETE button within
20 seconds, the display will return to normal display mode. Press and hold the DELETE button, then press the DOWN button, the following will show in the display:
The default language "EE" (English) will flash. Press the UP or DOWN button to choose your desired language (flashing). Press the DELETE button to confirm and accept. Then LCD CONTRAST (5-grey level) will show on the display. Use the UP or DOWN button to select the suitable grey-level and press the DELETE button to accept.
To program your Area Code:
While the first digit is flashing, you should:
1. Press the UP button until the first digit of your area code is dis­played (flashing).
2. Press the DELETE button to accept and go to the next digit.
3. Repeat steps 1 and 2 above to set the 2nd and 3rd digits of your area code.
4
Press UP & DELETE Press UP & DELETE Press UP & DELETE
“E” = English “F” = French “S” = Spanish
ESF
SET LANGUAGE
1 2 3 4 5
LCD CONTRAST
007
SET AREA CODE
SET AREA CODE
017
SET AREA CODE
817
To program the Time and Date:
Press the UP and DOWN buttons to get to the correct num­ber and the DELETE button to accept.
NOTE: You may not have to set up the Time
and Date manually as it may be auto­matically updated by Call Display infor­mation when your phone rings (twice or more). To get back to the standby mode (for dialing), press the DELETE button until the normal display shows (see right for example).
Adjusting the LCD Contrast Level
Y ou can also adjust the grey-level of the display without enter­ing the initial setup mode. Hold the DELETE button, then press the CALL BACK button to enter the LCD CONTRAST level setting mode. Use the UP or DOWN button to select the suitable grey-level and press the DELETE button to accept.
BASICS Choosing Tone or Pulse Dialing
Select the type of dialing by setting the TONE/PULSE switch. If you are not sure of your dialing system, make a trial call with the switch set to TONE. If the call connects, leave the switch as it is; otherwise, set it to PULSE. Even when your phone is set to pulse service, this phone can be switched to temporary tone for access to services that require tone sig­naling including Telephone Banking. Just press the TONE button after dialing in pulse and your buttons can now be used for tone signaling for this call only.
5
(Example: 10:53 a.m. on June 18th)
10:00 - 0/0
SET HOUR
10:53 - 0/0
SET MINUTES
10:53 - 0/18
SET DATE
10:53 - 6/18
SET MONTH
10:53 - 6/18
TOTAL 00 NEW 00
MAKING AND RECEIVING CALLS
MAKING A CALL
1. Pick up the handset.
2. Dial the phone number. The dialed number appears in the dis­play.
3. When you finish talking, replace the handset into the base.
RECEIVING A CALL
1. Pick up the handset when the phone rings.
2. When you finish talking, replace the handset into the base.
Volume Control and Ringer Setting
If you have subscribed to Call Display service, the caller’s number and/or name will appear in the display when you receive a call (see page 9).
Last Number Redialing and Pause Function
1. Pick up the handset.
2. Press the REDIAL button. The last dialed number appears in the display and is automatically dialed.
PAUSE FUNCTION
(Example: In an office where you need to dial a 9 first to get an outside line), dial the number 9 and press REDIAL button,
and then dial the phone number. You will see a “
PP
” displayed
for PAUSE. You may also store this into memory.
6
Adjust the handset volume
Adjust the ringer level
Slide the VOLUME control.
Set the RINGER switch. HI - loud rings on incoming calls. LOW - lower rings on incoming calls. OFF - no ringing on incoming calls.
MEMORY DIALING
You can quickly dial the numbers you stored into the 3 one­touch speed dial buttons or 10 two-touch speed dial memories. Storing Phone Number into Memory
1. Press the STORE button.
PPrroo
(short for programming) appears on
the display.
2. Dial the phone number you want to store. You can store up to 22 digits, including a TONE ( ) and a PAUSE (REDIAL), each of which is counted as one digit.
The stored number and the location will show in the display.
4. Press the STORE button, or wait 3 seconds to resume normal display.
5. Repeat steps 1-4 to store numbers into other memory locations.
NOTE: When the batteries are dead or removed for more than 5 min-
utes, the stored numbers may be erased.
TIP: If you entered a wrong number, you may press the STORE
button, then start from the beginning.
TO STORE A NUMBER TO BE DIALED VIA PRIVATE BRANCH EXCHANGE (PBX)
Before entering a phone number in Step 2 in Storing phone number into memory, do as follows:
1. Enter the outside line access digit (e.g., 9).
2. Press the REDIAL button (for a pause).
TO CHANGE A STORED NUMBER
Just store a new number, as described above, the old one will be erased automatically.
7
3. For one-touch dialing: Press one of the 3 one­touch speed dial but­tons (M1 to M3).
For two-touch dialing: Press the MEMO button, and the press one of the dialing keys (0 to 9) to store a phone number in.
Making Calls with One-Touch Speed Dial Buttons
1. Pick up the handset.
2. Press one of the one-touch speed dial buttons (M1 to M3).
3. The phone will dial the number you stored into it.
Making Calls with Two-Touch Speed Dial Locations
1. Pick up the handset.
2. Press the MEMO button first.
3. Press the desired two-touch memory number (0 to 9).
3. The phone will dial the number you stored into it.
CALL DISPLAY FEATURES
Understanding Call Display service
Call Display allows the caller’s phone number to be shown on the display after the second ring of the call, also in most cases, the caller’s name, calling time and date. This informa­tion will be stored automatically. In order to use this feature, you must first subscribe to the Call Display service. To use the call back feature, set the area code (see page 6).
When You Receive a Call
The caller’s phone number and/or name will not appear in the following cases:
- When the call is made through a telephone company which does not offer Call Display service (including international calls), the
display will show "
UUNNAAVVAAIILLAABBLLEE
".
- When the call is "blocked". For privacy reasons, many locations allow callers the option to prevent their telephone data from being displayed on the other party s Call Display display. The display
will show "
PPRRIIVVAATTEE CCAALLLL
".
- If the call is from an office which uses multiple lines, the displayed phone number may not match the number you use to call that extension.
- If you have picked up the phone before the second ring.
8
Viewing the Callers List
The phone stores the data of the last 70 calls received. It keeps track of all calls received, even if they were not answered. You can look through the data in the Callers List to check the numbers and names of the calls received.
1. Press the DOWN button. The data of the newest call appears for 15 seconds.
2. Press the DOWN button to view data from new to old, and the UP button from old to new.
* When you have reached the last (newest) call by pressing the UP
button, "END OF LIST" appears. If you press UP button again, the display will show the first (oldest) call.
* When you have reached the first (oldest) call by pressing the
DOWN button, "END OF LIST" appears. If you press the DOWN button again, the display will show the last (newest) call.
You can view the Callers List during conversation also by fol­lowing the steps above.
NOTE: If batteries are weak, the LOW BATTERY INDICATOR
is displayed. Replace new batteries as soon as possible; otherwise the Callers List and memories may be erased.
Calling back from the Callers List
Display the phone number you want to call back using the UP or Down button. Press the CALL BACK button. The display
will show "
PPIICCKK UUPP OORR AADDJJ
" or, if the handset is off hook "
DDIIAALLIINNGG oorr
AADDJJ
".
If the number can be Dialed as Displayed: Pick up the handset, the displayed number will dial out auto­matically. If the handset is already off hook, the number will dial out automatically in 2 seconds.
9
LOW
If the number cannot be Dialed as Displayed: Press the CALL BACK button and repeatedly press the but­ton to reformat the displayed number into a dialable number. Each press of the CALL BACK button displays another avail­able format, cycling back to the original format. You can choose one of the following formats:
1. 10 digit plus 1
2. 10 digit
3. 7 digit
If the handset is off hook, note that you have 2 seconds to reformat the number using the CALL BACK button. If you do not press the CALL BACK number, the telephone will attempt to dial the number as displayed on the screen.
NOTE: In many locations, the telephone company provides dis-
played telephone numbers in a ready to dial format. These numbers cannot be altered as they are already in the correct format to call back.
Storing Phone Numbers from the Callers List
As the phone keeps the data of up to 70 calls, if the 71st call comes in, the phone deletes the oldest data automatically. To prevent important calls from being deleted, you can store them into the 13 speed dial memory (3 one-touch and 10 two-touch).
1. Display the phone number you want to store.
2. Press STORE button. The number is repeated in the display. Press CALL BACK to select the number you want to store (for example, 14162353453 or 4162353453 or 2353453).
The phone number is now stored in that memory button.
10
3. For one-touch memory: Press a one-touch speed dial button (M1 to M3).
For two-touch memory: Press the MEMO button, and then any speed dial memories (0 to 9)
Note: Only the number will be stored, not the name.
Deleting the Data from the Callers List TO DELETE THE CALL DISPLAY MEMORY ONE BY ONE
1. Display the entry you want to delete.
2. Press the DELETE button twice quickly, the display shows the next or previous call, and the data is deleted.
TO DELETE ALL CALLERS LIST ENTRIES
1. Make sure that all NEW calls have been reviewed (NEW CALL INDI­CATOR (at the back of the handset) does not flash).
2. Press the UP or DOWN button to display any call, make sure the display does not show "
EENNDD OOFF LLIISSTT
".
3. Press and hold DELETE button down for 6 seconds. Display changes to "
NNOO CCAALLLLSS
", all Callers List Entries are deleted.
NOTE: You cannot delete all the Callers List Entries when there are
any new calls remaining (not viewed yet), or when "
EENNDD OOFF
LLIISSTT
" is shown on the display.
Using Message Waiting/Mailbox
To use the Message Waiting feature, you must subscribe to this service if available from your local telephone company. This phone will only respond to FSK type of message delivery .
1. If the message is sent by the telephone company which is pre­ceded by a ring, the MESSAGE WAITING symbol will appear on the display, and the NEW CALL INDICATOR will flash after 20 seconds.
2. After you retrieve your message(s), the telephone company will send a clear signal (by a ring) to your phone. The symbol will turn off until a new message is received. The NEW CALL INDI­CATOR will stop flashing. Sometimes the telephone company will not send a message clear signal to your phone, then you will have to clear the message waiting symbol manually by holding the DELETE button, then pressing the UP button.
11
WALL MOUNTING
This phone can be mounted on a wall phone plate. If you do not have a modular wall phone plate installed, please consult with your phone company or installer to get one, or see the following for installation without a wall plate.
1. Use the SHORT STRAIGHT WALL CORD, and plug one end into the rear of the phone.
2. Plug the other end into the WALL JACK.
3. Put the phone over the WALL PLATE, make sure both posts fit into slots on the back of the phone. Then slide down to lock the phone into the WALL PLATE.
WALL MOUNTING WITHOUT A MODULAR WALL PHONE PLATE
Follow these instructions to mount the phone on the wall without a wall plate:
1. Locate a wall stud. If it is possible to uti­lize a wall stud for mounting, dry wall expanders or a similar type fastener is recommended. Consult your local hard­ware store for details.
2. Drill 2 holes 3-15 / 16 " (100 mm) apart.
3. Put a screw into each hole and leave 3/16" (5mm) of the head exposed to mount the phone, (screws are not included).
4. Connect the straight long cord to the phone and jack.
5. Place the TELEPHONE BASE on the 2 mounting screws and gently push down to lock into place.
IMPORTANT
Before mounting the phone onto the wall, select a wall area with sufficient strength. If mounting on the wallboard or in an area of questionable strength, locate a stud for maximum support of your telephone.
12
13
Drill one hole
Make sure the space between holes is 100mm
Drill one hole
TROUBLE SHOOTING
14
PROBLEMS
No dial tone
Phone does not work
Phone does not ring
Can not dial
Display shows erro­neous figure OR No dial tone or Low dial tone or cannot dial out
Cannot store into memory
Call Display does not work
The display gets dim or is blank
CHECK
Is any plug disconnected from the modu­lar phone plug? Is any jack improperly wired? Use another phone to test the jack.
Are all cords connected properly? Are all 3 "AA" batteries installed? Make sure they are installed according to the polari­ty shown.
RINGER switch may be set to OFF. Slide switch to HI or LOW position.
Check the TONE/PULSE switch setting. You may only have PULSE service. Set the TONE/PULSE switch to PULSE.
You may have selected the wrong lan­guage. Refer to page 7 and reset the lan­guage. It may be helpful to remove the bat­teries and the line cord for 30 seconds first.
No batteries are installed or batteries are weak or installed up-side-down.
Make sure the Call Display service is active.
- The phone is connected to a working wall jack.
- All line cord connections are correct and
secure.
Check if batteries are properly installed, and if you have received the first Call Display record. If you have, your batter­ies may be weak. Replace all batteries.
15
PROBLEMS
The Call Display dis­play does not show the caller’s informa­tion
Static noise on line, cannot hear calling party or calling party can not hear you
Redial does not work
Line error shows in the display
CHECK
The Call Display unit will not function until you have subscribed to Call Display serv­ice from your local telephone company. Call your local telephone company to have Call Display service installed on your phone line. Also, fresh batteries must be installed. Make sure all your phone line connections are secure and correct. If it is a private call or a blocked call, the caller’s name and/or phone number will not appear on the display. (You will see time and date of call plus some dashes or the words "UNAVAILABLE" or "PRIVATE CALL".)
Make sure the HANDSET CORD is con­nected properly, or replace the COILED HANDSET CORD. Any phone store has these cords in different lengths. After some time the cord may become over­stretched or damaged.
Check if
PP
shows in the display. Since the REDIAL button has combined function (pause), the phone may have been paused. Just press the HOOK switch to get a new dial tone.
You picked up the phone before the sec­ond ring, or your phone received no information or unclear information. Static can cause this message. If this condition persists, contact your local telephone company to ensure there is no problem with your phone line.
16
PROBLEMS
Call Display displays words like
CCHHOOIISSIIRR ZZOONNEE
or
TTIIEEMMPPOO
or
CCOODDIIGGOO DDEELL
AARREEAA
or
AAPPEELL
Memory Dialing does not work
Caller’s number is not registered to the Callers List
Message Waiting does not work
Pressing a MEMORY button does not dis­play number
CHECK
Your language is set for French or Spanish. To reset the language, press and hold the DELETE button and then
press the DOWN button. While
EE
is flashing, press the DELETE button to confirm. The language will be set to English mode.
Check if you have stored the numbers correctly by pressing that memory loca­tion button(s). Also numbers can only be stored when fresh batteries are installed.
The caller may have a blocked number to prevent Call Display identification, or it may be an overseas call or you may have noise on the line during that call.
Check with your local telephone compa­ny to see if this service is available and if you have subscribed to it.
The MEMORY button has no stored number. Please store the number again. Press the STORE button, dial the num­ber and then press the MEMORY loca­tion.
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the following type and size of batteries: 3 size "AA" alkaline batteries.
2. Do not dispose the batteries into a fire. The cells may explode. Check with local codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swal­lowed.
4. Be careful when handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. The battery or conductor may over heat and cause burns.
5. Do not attempt to recharge the batteries that are used with this product. The batteries may leak corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by heating them. Sudden release of the battery electrolyte may cause burns or irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and dis­charged batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity or direc­tion must be observed. Reverse insertion of batteries may result in the leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long period of time (several months or more) since during this time the batteries could leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to leak in the product. Batteries should be replaced when the display gets dim or if the LOW BATTERY INDICATOR shows.
11. Do not store this product in high temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose of extending shelf life should be protected from condensation during storage and defrosting. Batteries should be stabilized at room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING on pages 14 and 16. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.
13. Installation of batteries should only done by an adult.
17
Limited Time Offer for
Sprint Canada Local Customers!
Unlimited Internet Access only $ 13.95 per month!
- Unlimited Internet access
- Free 24-hour Technical support
- Free Personal Web Page (16Mb)
- Free Easy-to-use Web Page building tool
- 30-day Satisfaction Credit
- Instant Messaging
- Great Web Content
© Copyright 2003 Aastra Telecom Inc. All Rights Reserved.
FOR QUESTIONS RELATED TO THE TELEPHONE SET PLEASE CALL AASTRA TELECOM INC. CUSTOMER SERVICE AT: 1 866-316-1118
FOR QUESTIONS RELATED TO YOUR LOCAL PHONE SERVICE PLEASE CALL SPRINT CANADA CUSTOMER CARE AT 1 800-980-5464
Loading...