Sprayon S00315000 User Manual

MR™315 Urethane & Styrene Silicone Release Agent Aerosol

Not available.
Aerosol.

US / Canada: [phone]
Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year

SAFETY DATA SHEET

Product name

Other means of
identification

Product type

Emergency telephone
number of the company

Section 1. Identification

:

:
:

:

Manufacturer

:

Sprayon Products Group
101 W. Prospect Avenue,
Cleveland, Ohio 44115

Relevant identified uses of the substance or mixture and uses advised against

Paint or paint related material.

S00315000

S00315000

Product code

:

Product Information
Telephone Number

:

US / Canada: [phone]
Mexico: Not Available

Regulatory Information
Telephone Number

:

US / Canada: [phone]
Mexico: Not Available

Transportation Emergency
Telephone Number

:

US / Canada: [phone]
Mexico: SETIQ 01-800-00-214-00 / (52) 55-5559-1588 24 hours / 365 days a year

Section 2. Hazards identification

FLAMMABLE AEROSOLS - Category 1
GASES UNDER PRESSURE - Compressed gas
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) ­Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2

Classification of the
substance or mixture

:

Hazard pictograms

:

GHS label elements

Percentage of the mixture consisting of ingredient(s) of unknown acute oral toxicity:

89.9%
Percentage of the mixture consisting of ingredient(s) of unknown acute dermal toxicity:

89.9%
Percentage of the mixture consisting of ingredient(s) of unknown acute inhalation
toxicity: 65.7%

OSHA/HCS status

:

This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).

Date of issue/Date of revision

:

11/28/2019

Date of previous issue

:

8/17/2017

Version

:51/13

S00315000

MR™315 Urethane & Styrene Silicone Release Agent Aerosol

SHW-85-NA-GHS-US

Section 2. Hazards identification

Signal word

:

Danger

Precautionary statements

Prevention

:

Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No
smoking. Do not spray on an open flame or other ignition source. Use only outdoors or
in a well-ventilated area. Do not breathe dust or mist. Pressurized container: Do not
pierce or burn, even after use.

Response

:

Get medical attention if you feel unwell. IF INHALED: Remove person to fresh air and
keep comfortable for breathing. Call a POISON CENTER or physician if you feel unwell.

Storage

:

Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50
°C/122 °F. Store in a well-ventilated place.

Disposal

Dispose of contents and container in accordance with all local, regional, national and
international regulations.

Hazards not otherwise
classified

:

None known.

Extremely flammable aerosol.
Contains gas under pressure; may explode if heated.
May cause respiratory irritation.
May cause drowsiness or dizziness.
May cause damage to organs through prolonged or repeated exposure.

:

Hazard statements

Please refer to the SDS for additional information. Keep out of reach of children. Keep
upright in a cool, dry place. Do not discard empty can in trash compactor.

Supplemental label
elements

DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains a chemical known to the State of California to cause birth defects
or other reproductive harm. FOR INDUSTRIAL USE ONLY.

:

Section 3. Composition/information on ingredients

1,1-Difluoroethane

≥50 - ≤75

75-37-6

Dimethyl Ether

≥25 - ≤50

115-10-6

Light Aliphatic Hydrocarbon Solvent

<9

64742-49-0

Lt. Aliphatic Hydrocarbon Solvent

<0.5

64742-89-8

Methyl Cyclohexane

<0.5

108-87-2

Ingredient name

CAS number

% by weight

There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health and hence require reporting in this section.

Other means of
identification

:

Not available.

Substance/mixture

CAS number/other identifiers

:

Occupational exposure limits, if available, are listed in Section 8.

Mixture

Any concentration shown as a range is to protect confidentiality or is due to batch variation.

Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention following exposure or if feeling unwell.

Section 4. First aid measures

Eye contact

:

Description of necessary first aid measures

Date of issue/Date of revision

:

11/28/2019

Date of previous issue

:

8/17/2017

Version

:52/13

S00315000

MR™315 Urethane & Styrene Silicone Release Agent Aerosol

SHW-85-NA-GHS-US

Section 4. First aid measures

Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. If necessary,
call a poison center or physician. Never give anything by mouth to an unconscious
person. If unconscious, place in recovery position and get medical attention
immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt
or waistband.

Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention following
exposure or if feeling unwell. Wash clothing before reuse. Clean shoes thoroughly
before reuse.

Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of
inhalation of decomposition products in a fire, symptoms may be delayed. The exposed
person may need to be kept under medical surveillance for 48 hours.

Skin contact

Inhalation

Ingestion

:

:

:

Notes to physician

:

In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.

Specific treatments

:

No specific treatment.

Most important symptoms/effects, acute and delayed

Inhalation

:

Can cause central nervous system (CNS) depression. May cause drowsiness or
dizziness. May cause respiratory irritation.

Can cause central nervous system (CNS) depression.

:

Ingestion

Skin contact

:

No known significant effects or critical hazards.

No known significant effects or critical hazards.

:

Eye contact

Over-exposure signs/symptoms

Skin contact

Ingestion

Inhalation

Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness

No specific data.

No specific data.

:::

Eye contact

:

Adverse symptoms may include the following:
irritation
redness

Potential acute health effects

Indication of immediate medical attention and special treatment needed, if necessary

Date of issue/Date of revision

:

11/28/2019

Date of previous issue

:

8/17/2017

Version

:53/13

S00315000

MR™315 Urethane & Styrene Silicone Release Agent Aerosol

SHW-85-NA-GHS-US

Section 4. First aid measures

Protection of first-aiders

:

No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.

Hazardous thermal
decomposition products

Specific hazards arising
from the chemical

Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
halogenated compounds
carbonyl halides

Extremely flammable aerosol. Runoff to sewer may create fire or explosion hazard. In
a fire or if heated, a pressure increase will occur and the container may burst, with the
risk of a subsequent explosion. Gas may accumulate in low or confined areas or travel
a considerable distance to a source of ignition and flash back, causing fire or explosion.
Bursting aerosol containers may be propelled from a fire at high speed.

Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Special protective
equipment for fire-fighters

Use an extinguishing agent suitable for the surrounding fire.

Extinguishing media

:

:

:

None known.

Suitable extinguishing
media

:

Unsuitable extinguishing
media

:

Special protective actions
for fire-fighters

:

Section 6. Accidental release measures

Environmental precautions

Personal precautions, protective equipment and emergency procedures

:

:

No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. In the case of aerosols being ruptured, care should be taken due to the rapid
escape of the pressurized contents and propellant. If a large number of containers are
ruptured, treat as a bulk material spillage according to the instructions in the clean-up
section. Do not touch or walk through spilled material. Shut off all ignition sources. No
flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.

Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up

For non-emergency
personnel

For emergency responders

:

If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non­emergency personnel".

Date of issue/Date of revision

:

11/28/2019

Date of previous issue

:

8/17/2017

Version

:54/13

S00315000

MR™315 Urethane & Styrene Silicone Release Agent Aerosol

SHW-85-NA-GHS-US