SpotSee SpotBot CEL Quick Start Guide

STEP 4

CONFIGURE SPOTBOT UNIT (CONTINUED)

STEP 5

SPOTBOT IN USE

D. Remove the rubber cover from the front of your
SpotBot Unit

E. Connect your computer to the SpotBot using the
Micro-USB Cable provided

F. Push the “Start/Stop” button the front of the SpotBot Unit

Unit ID will appear within the Profile Pop Up Window (shown below)

G. Select the desired
“Alarm Threshold”

Note: Impacts at a
G-level above the
“Alarm Threshold”
will send alarms

visible in the
SpotSee Cloud

H. Select desired
“Summary Time”

Note: Summary time
dictates the interval
that the SpotBot will

send impact, location,
and temperature
summaries to the
SpotSee cloud. Less
frequent intervals will improve battery life.

A. Begin Monitoring – Press “Start/Stop”

Button in the Access Port. The “On” and

“Sending” lights will both flash green.

B. In Use (No Alarm) – When SpotBot is in use and not in process
of sending an alarm to the SpotSee Cloud the “On” light will flash
green every minute if no alarm has occurred. This light will flash
yellow if the unit has low battery life remaining.

C. In Use (Alarm) – If an alarm has occurred, the red “Alarm” light
and the green “On” light will flash every minute.

D. Alarm Triggered – When SpotBot experiences an impact above

the “Alarm Threshold” the “Alarm” (red) as well as the “On” and

“Sending” (green) lights will flash at different intervals. The lights

continue to flash as the SpotBot Unit sends the alarm data to the
SpotSee Cloud.

E. Unit Status Check – To check the status of the SpotBot Unit,
press the “On/Off” button for 1 second. If the “On” light flashes
green and the “Alarm” light flashes red, an alarm has occurred. If

the “Alarm” light does not flash, then no alarm has occurred.

F. Stop Monitoring – Press and hold the

“On/Off” button (for approximately 5 seconds)

until all (3) lights stop flashing and remain on.

For additional operations, please refer to the product manual.

QUICK START GUIDE

I. Enable and set temperature alarms

Note: High and/or low temperature thresholds may be enabled

and set

J. Click “Save”
Status message will appear noting “Save Successful”

K. Close the configuration window and unplug the
Micro-USB Cable

L. Replace the rubber cover

This document is written and published by ShockWatch, Inc. All rights reserved.

FOR QUESTIONS OR TROUBLE SHOOTING PLEASE
CONTACT TECHNICAL SUPPORT

Email:[e-mail]

ShockWatch Canada & Americas
US:[phone] Outside US:[phone]

ShockWatch Europe, Middle East, Africa:+31.55.7370 148

ShockWatch Asia-Pacific:[phone]

HARDWARE OVERVIEW

Access Port

Unit ID Number

On/O ff Micro USB PortReset

STEP 1

ACTIVATE THE SPOTBOT

A. If this is the first connected device purchase for your
company, you must establish an account admin. This
person will be responsible for managing user access to
the SpotSee Cloud.

C. Enter the admin email address in the pop-up box and
click Enter

An email will be sent to the Admin’s email address from
[e-mail].

Note: If the email is not received within 5 minutes, please check
your spam or junk folders. If it has still not been received,
please contact SpotSee technical support.

D. Follow the link in the email to create your password.

Note: Steps C and D will only be necessary the first time an
account is set up on the SpotSee Cloud.

E. A message will prompt you to
select an available contract
for the unit. Click the
dropdown list to select a
contract. Click Activate.

Note: Multiple contracts may
exist for your account. Select the
contract that you wish to match
to the specific SpotBot unit
being activated.

F. Your SpotBot unit has now
been activated.

E. Click “Add”

An email will be immediately sent to the New User which will
prompt them to set up a Password

F. Repeat this process for additional users

STEP 3

BATTE RY I NSTALL ATION

A. Remove SpotBot
Unit and Batteries
from the box

B. Unscrew Battery Panel

(see image to the right)

Required to complete

this step.

C. Install the (6) AA batteries provided in the direction
notated within each battery slot and replace Battery
Panel making sure that CE sticker is visible. Tighten the
screws on the battery cover to a torque setting of 116 -
121 inch-ounces to preserve IP ratings

B. Navigate to activate.spotsee.io to begin the
activation process.

Enter the Customer Number found
on the packing list that shipped with
the SpotBot, the SpotSee invoice or
order acknowledgement.

Enter the Unit ID found on the front
label of the SpotBot.

Accept the Terms and Conditions

Click Activate.

STEP 2

SET UP OF ADDITIONAL USERS

A. Navigate to cloud.spotsee.io and log in using the ADMIN
email address and password created in STEP 1

B. Click on “Users” in the column on the left side of the
web page

C. Click on Plus Sign in upper right of screen

D. Insert (Name, Email Address, and Mobile Phone #) and
Select the Role for the New User

STEP 4

CONFIGURE SPOTBOT UNIT

A. Navigate to cloud.spotsee.io and login using the email and
password that were generated during the User Set Up
process by the ADMIN

B. Click on “Configure Unit” in the column on the left side of
the web page

C. Go to initial setup and follow the steps for your chosen
browser. Click “Launch Configuration Application” to
launch and run the SpotBot Software