Spot PT3 User Guide
SPOT GEN3 USER GUIDE
S.O.S.
Tra ck i n g Check In Help/ SPOT Assi st
1
HOW SPOT WORKS
GPS satellites provide signals.
1
SPOT determines your GPS location and sends
2
your location and pre-programmed message to
communication satellites.
Communication satellites relay your message to
3
specific satellite antennas around the world.
Satellite antennas and a global network route your
4
location and message to the appropriate network.
Your location and messages are delivered
5
according to your instructions via email, text
message, or emergency notification to the
GEOS International Emergency Response
Coordination Center.
Powered by Google Maps™
When SPOT sends a text or email message to
one of your contacts or to GEOS, it includes your
GPS coordinates and a web link (email only) to
view your location using Google Maps™.
SecTiOn 1: WeLcOMe
Welcome to the SPOT Family! SPOT devices provide satellite-based
messaging capability so everyone who enjoys the great outdoors
can communicate from remote locations around the globe, beyond
the reach of cell phones. Pretty cool, huh?
HERE ARE A FEW IMPORTANT THINGS
TO REMEMBER ABOUT YOUR SPOT GEN3
SPOT needs a clear view of the sky to obtain a GPS signal to provide the most accurate
location information. SPOT is not as reliable indoors, at the bottom of a deep canyon, in a
cave, or in very dense woods. Sunshine is more fun anyway!
Orienting SPOT so that the SPOT logo is facing up toward the sky will improve performance
as the antenna is located directly under the logo. The coolest adventurers place SPOT on
their backpacks.
In order to ensure best performance, do not use SPOT immediately adjacent to other GPS devices.
To begin using SPOT, we recommend you spend a few minutes reading through this User Guide,
then visit FindMeSPOT.com to select a service plan and activate your SPOT device.
2
3
SecTiOn 2: GeTTinG STaRTed
Your SPOT Gen3 requires an active SPOT subscription to communicate. To do this,
simply activate your device using the instructions outlined below.
WITH YOUR SPOT
WHAT YOU NEED
• Your SPOT Gen3
• One of these three power sources:
- 4 AAA Energizer® Ultimate Lithium 8x batteries (L92); included
- 4 AAA Energizer® NiMH rechargeable batteries (NH12)
- Line Power with a 5v USB connection
• User Guide
INSTALL THE INCLUDED BATTERIES
1. Loosen the screws to open the battery cover.
2. Write down the ESN and Authorization Code for use during service activation.
3. Install 4 AAA Energizer® Ultimate Lithium 8x batteries or NiMH rechargeable batteries.
4. Replace cover, tighten screws with a screwdriver or coin. It is important that you
fully tighten the battery cover to maintain SPOT's waterproof seal.
AT FINDMESPOT.COM
WHAT YOU NEED
• Personal contact information
• Emergency contact information
• Valid email address
• Credit card information
• SPOT electronic serial number (ESN) and authorization code.
ACCOUNT SETUP
1. Go to FindMeSPOT.com/Activate.
2. Existing SPOT customers should login to their current SPOT account to add their new device. New
customers will need to select: Set Up New Account.
3. Follow the instructions given within the activation portal; do not skip forms or pages.
4. Choose the services you wish to add (like the new upgraded Unlimited and Extreme Tracking) to
your SPOT device and confirm your order to finish the activation process.
SERIAL NUMBER (ESN) AND
AUTHORIZATION CODE
These codes are located inside the battery compartment
of your SPOT Gen3. You will need these codes when
setting up your account on FindMeSPOT.com/Activate.
ESN: 0-0000000
ELECTRONIC SERIAL
NUMBER (ESN)
AUTHORIZATION CODE
Auth: 00000000
4 5
S.O.S
SecTiOn 3: funcTiOnS
HELP/SPOT ASSIST
Request help from your friends & family at your GPS location. Or ask for help from
professional assistance organizations. (Example: Flat tire, need a lift.)
CUSTOM MESSAGE
Let contacts know where you are by sending a pre-programmed message with your
GPS location.
S.O.S.
In an emergency, send an S.O.S. with your GPS location to GEOS, who facilitates search
and rescue. (Example: Snake bite, broken leg)
CHECK IN
Let contacts know where you are and that you’re okay with a pre-programmed message.
TRACK
Automatically send and save your location and allow contacts to track your progress
using Google Maps™.
HELP/SPOT ASSIST
TRACK
POWER
Press the power button to turn SPOT on; LEDs will illuminate. Press and hold the power
button until it blinks rapidly to turn SPOT off.
CHECK IN
CUSTOM MESSAGE
6 7
GPS LIGHT
Noties you whether or not SPOT is able to see the GPS satellites & obtain your GPS location.
MESSAGE SENDING LIGHT
Notifies you whether or not your most recent message was transmitted.
SecTiOn 3: uSinG SPOT
POWER
There are three ways you can power your SPOT: 4 AAA Energizer Ultimate Lithium 8x batteries
(included), 4 AAA NiMH rechargeable batteries, or with line power through a 5v USB connection.
Insert batteries or attach the USB cable to your SPOT and a power source. Please note: NiMH
batteries cannot be charged within the SPOT unit using line power, and SPOT Gen3 is not
waterproof while being line powered.
TO TURN SPOT ON: Simply locate the Power button on the upper left corner of the device, press and
hold the button; lights will illuminate.
TO TURN SPOT OFF: Press and hold the Power button until the Power light blinks rapidly.
TO CONSERVE POWER: Your SPOT unit will automatically turn off after one hour of inactivity unless
the unit is being line powered.
SELF TEST
SPOT performs a self-test when you initially turn on your device. During self-test, all lights will blink
green in a rotating manner to indicate self-test is in progress. If all visible lights flash red, the SPOT
self-test has found a failure, please call customer care.
If the Power, GPS light and Message Sending light blink red in unison, SPOT has a GPS failure, but
may still be able to transmit an S.O.S. or Help/SPOT Assist message without your GPS location.
INITIAL SYSTEM TEST
Perform an initial system test to evaluate your messaging system, from the operational
condition of the SPOT to the readiness of those you’ve chosen to receive your messages.
Once you have set-up the message contacts for SPOT Gen3 in your FindMeSPOT.com account,
1
go outside where SPOT has a clear view of the sky in all directions.
Turn SPOT on - press and hold the Power button; lights will illuminate.
2
Press and hold the Check In button until the function light blinks green.
3
Leave SPOT outdoors. The GPS light will blink green as SPOT acquires a GPS fix. Once
4
SPOT acquires your GPS location, the Message Sending light and GPS light will blink green
in unison for 15 seconds to notify you that your message is being transmitted with your GPS
location. The Message Sending light will continue to blink green until the message cycle is
complete.
Verify that the message was received in the email or SMS account(s) in your Check In contact list.
5
You can also view your sent messages in your account at FindMeSPOT.com.
Add your email or phone number as a contact for
system testing so you can hit the trail faster.
8 9
Loading...