Sport-thieme 115 0953, 239 2918, 239 2905, 113 6500, 239 2400 Assembly Instruction Manual

Thanks for choosing Sport-Thieme equipment!

In order to enjoy this product please note the following instructions for safety, use and maintenance before assembly.

Assembly instruction

Cat.-no.

: 115 0953

2392905

239 2918

113 6500

239 2400

239 2413

0118816 · © 2018 Sport-Thieme GmbH

Cat.-no. 115 0953:

Sport-Thieme®
Handball Goal, 3x2 m,
Free-standing with Fixed
Net Brackets

Sport-Thieme®
Handball Goal

3x2 m, Free-standing with Fixed Net Brackets

Cat.-no. 113 6500:

Sport-Thieme®
Handball Goal, 3x2 m,
standing in ground sockets.
With xed net brackets

D-38367 Grasleben · Germany
sport-thieme.com · info @sport-thieme.com
Phone: [phone] · Fax: [phone]

2

Assembly instruction Cat.-no.

115 0953; 113 6500

1. Scope of delivery

Please check the following content before assembly.

The following indicated quantities refer to 1 goal. In case of a delivery in pairs we double the amount cor-

respondingly. Pictured colours of proles are only samples and may dier from delivered proles.

Piece Description

1 Galvanized steel ground tube Ø ¾“

1 Crossbar, prole 80 x 80mm

2 Upright, prole 80 x 80mm

1 Hexagon screwdriver SW6, DIN 911, length approx. 470mm (only for goal in ground sockets)

Piece Description

2 Aluminium cast corner joint

2 Upright cap

1 Accessories

Piece Description

2 Rigid net hoop

Piece Description

Following parts only for catalogue no.
113 6500 – goal in ground sockets

2 Ground socket, length 300 mm

2 Cap for ground socket

3

Assembly instruction Cat.-no.

115 0953; 113 6500

Accessories

Piece Description

32 Net holder

8 Nut, 40 mm, thread M8

2 Bush with thread M8, of aluminium round tube 20 x 5 mm, length 40 mm

6 Plastic holder

8 Hexagon socket screw M8 x 20, DIN 7991

8 Hexagon socket screw M8 x 14, DIN 912

8 Hexagon screw, M8 x 16, DIN 933

2 Hexagon screw M8 x 90, DIN 931

2 Hexagon screw M8 x 12, DIN 933

2 Self-locking nut M8, DIN 985

4 Self-locking cap nut M8, DIN 986

8 Nut M8, DIN 934

4 Ring nut M8 x 50

8 Plug pin

1 Hexagon screwdriver SW5, DIN 911, black

1 Hexagon screwdriver SW6, DIN 911, length 120 mm

1 Assembly instruction

4

Assembly instruction Cat.-no.

115 0953; 113 6500

2. Assembly of the goal

The following tools are necessary:

- 2 wrench/ring spanners 13 mm

- 1 mallet/hammer

- 1 drill Ø 1,5 mm

- 1 thin screw driver (for net hook xing if necessary)

a) Assembly of crossbar/uprights:

Lay crossbar and uprights on the ground, groove facing upwards and mitres joining. Stick at each goal frame corner 4 nuts

with thread M8, length 40 mm into the groove of the net hook rail (push 2 into the upright and 2 into the crossbar, see 1st
picture bottom left). Stick cast corner joint into crossbar’s end (see 2nd picture bottom right). Then add the upright. Take care
that the internal edge of corner upright/crossbar is nearly closed. The external edge should be somewhat open, see 3rd pic­ture bottom left. Screw 2 hexagon socket screws DIN 7991, M8 x 20 in the internal corner (see 4th picture bottom right).

PfostenLatte

2. insert aluminium cast
corner joint

leave open external edge

3. push mitre of
internal edge close
together

4. screw hexagon socket
screws M8 x 20 slightly

1. push nuts into the groove

in angled position
screws screwless
the hexagon
socket screws