SPORTSPOWER MSC-4120-BM, MSC-4146, MSC-3788-5S-BM, MSC-4118-BM Owner's Manual
1
MODEL # MSC-4120-BM
Spring Breeze with
Me and My Toddler Metal Swing Chair
OWNER’S MANUAL
ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USER INSTRUCTIONS
FOR RESIDENTIAL USE ONLY
For Customer Service, please call 1-866-370-2131 or visit www.sportspowerltd.net
Monday – Friday 9:00 AM – 5:00 PM Eastern Time
Sportspower Ltd.
Flat M, Kaiser Estate Phase 3, 11 Hok Yuen Street, Hunghom, Kowloon, Hong Kong
Corporate Office 1-800-497-6106
WARNING
This product is designed to be used simultaneously by up to 6 persons between ages 3 to 8
weighing no more than 100lbs (45kg) each, with the exception of the swing chair which is
intended for toddlers between 18-30 months old (max 35lbs/16kg) and supervised by an adult
(max 175lbs/80kg).
Combined weight of all users must not exceed 600 lbs (270 kg).
Carefully read this entire instruction manual before you start to assemble or use this swing set.
You must follow all instructions and warnings while using this equipment.
Do not use this swing set on hard packed soil, concrete or any kind of hard surface.
This equipment must be anchored (anchors not included). You should consult your local
contractor regarding the best way to anchor the product in your location of installation.
Assembly requires at least two adults.
2
INTRODUCTION
Dear Valued Customer,
Congratulations on your Sportspower play set purchase! Please read and completely understand the
contents of this owner’s manual. This manual contains specific instructions and warnings that must be
followed to prevent injuries.
This play set is for residential use only. This play set is NOT intended for public or commercial use. The
warranty will be voided if the play set is used in a commercial application.
The product is designed for children between ages 3 to 8, except for Me and My Toddler Metal Swing
Chair component which is for a toddler aged 18-30 months and supervised by an adult. Children must NOT
play on this set until it is properly assembled and inspected by an adult. Adult supervision is required at all
times while children are playing on the equipment. Do not allow children under six (6) years old to be near
during the assembly of this product due to choking hazards of small parts.
The equipment must be installed on level ground. Uneven ground must be leveled prior to installation.
Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and
unstable which may result in serious injuries. You must ensure there are no obstructions or structures (e.g.
electrical wires, branches, house, fence, garage, etc) within six (6) feet from the equipment. The Consumer
Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend to install and
maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber (for
equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock
absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground
equipment, do not adequately protect children from serious head injuries. Install protective surfacing at
least six feet in all directions from play equipment. For swings, the surface should extend, in back and front,
twice the height of the suspending bar. Do not install your play set over hard surface, e.g. asphalt, concrete,
packed earth, tile or brick floor. We recommend that you refer to the CONSUMER PRODUCT SAFETY
COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK, extracts of which are
contained in this manual for reference.
Do not allow children to use the product during windy or wet weather conditions. You should consult a
local licensed contractor about ways to anchor the product in your location.
The equipment must be checked before each use and maintained regularly. This includes, but is not
limited to inspecting the play set for cracks, excess wear, missing parts, loose connections and for overall
integrity. When the equipment shows any signs of weakness or damage, you must stop using the play set
immediately, properly store away the set or restrict access by users until the condition is resolved.
Your product is warranted against defects in material and workmanship. Extended warranty is also
offered to those customers registering their products at www.sportspowerltd.net within 14 days
from the date of purchase. Please refer to our warranty policy at the back of this manual for details.
If you experience any problems with your product, do not return to the store. For customer service,
please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time or visit
www.sportspowerltd.net
3
TABLE OF CONTENTS
IMPORTANT INSTRUCTIONS AND WARNINGS ................................................................................................................ 4
IMPORTANT CONSUMER INFORMATION SHEET ............................................................................................................ 8
ANCHORING............................................................................................................................................................................ 9
CARE AND MAINTENANCE CHECKLIST ......................................................................................................................... 11
TOOLS NEEDED ................................................................................................................................................................... 12
PARTS LIST ........................................................................................................................................................................... 13
ASSEMBLY AND INSTALLATION INSTRUCTIONS ........................................................................................................ 19
AREA OF INSTALLATION - SWING SET TOP BAR ........................................................................................................... 19
AREA OF INSTALLATION - SIDE LEGS .............................................................................................................................. 20
AREA OF INSTALLATION - CROSS BARS ......................................................................................................................... 21
AREA OF INSTALLATION - SWING SEAT .......................................................................................................................... 22
AREA OF INSTALLATION - TRAPEZE ................................................................................................................................. 23
AREA OF INSTALLATION - SLIDE ....................................................................................................................................... 24
AREA OF INSTALLATION - ME AND MY TODDLER METAL SWING CHAIR…………………………………………….……….28
MANUFACTURER’S LIMITED WARRANTY............................................................................................................................ 41
4
IMPORTANT INSTRUCTIONS AND WARNINGS
WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT
Observing the following statements and warnings reduces the likelihood of serious or fatal injury
AGE LIMIT
This product is designed to be used simultaneously by up to 6 persons between ages 3 to 8 weighing no
more than 100lbs (45kg) each, with the exception of the swing chair which is intended for toddlers
between 18-30 months old (max 35lbs/16kg) and supervised by an adult (max 175lbs/80kg).
Combined weight of all users must not exceed 600 lbs (270 kg).
On-site adult supervision is required at all times for children of all ages.
Do not allow use by children with any physical condition that may affect his/her ability to use this
equipment safely.
BEFORE YOU BEGIN
Carefully read all instructions in this manual before assembling and using this product.
This unit must be assembled by adults. Heavy duty working gloves must be worn to avoid injuries
during assembly.
Do not allow children under six (6) years old to be near during assembly due to choking hazard of small
parts.
Adult supervision is required during the use of this equipment at all times.
Unpack all parts. Take a complete inventory of all parts and hardware using the parts and hardware lists
in the following pages. If any parts are missing, do not return to the store. Please call customer service
toll-free number listed on the cover page for assistance. Store the product back in the original box and
do not begin to install until all parts are obtained.
LOCATION OF PLAY SET
The equipment must be placed more than six (6) feet (1.8 meters) from any structures or obstructions,
including but not limited to buildings, fence, garage, trees, laundry lines, electrical wires. Children can be
seriously injured running or swinging into obstacles.
The play set must be installed on level ground. Uneven ground must be leveled prior to installation.
Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose
and unstable which may result in serious injuries.
Remove any tripping hazards from the safe play area, such as roots, tree stumps, rocks, landscaping,
sprinkler heads, railroad ties, plumbing and electrical connections.
5
Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick
floor. A fall onto a hard surface can result in serious injury or death to the user. The following is a
list of recommended ground covers from the Consumer Product Safety Commission:
SUGGESTED MATERIAL UNCOMPRESSED DEPTH
Double Shredded Bark Mulch 9”
Uniform Wood Chips 12”
Fine Gravel 12”
Fine Sand 12”
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommend
to install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded
rubber (for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as
shock absorbing material. Dirt and grass, which are the most prevalent surfaces under home playground
equipment, do not adequately protect children from serious head injuries. Install protective surfacing at least
six feet in all directions from play equipment. For swings, the surface should extend, in back and front, twice
the height of the suspending bar. You should consult a local contractor about ways to secure the product in
your location. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick
floor. Please refer to the CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK for detailed guidelines to prevent injuries from falls and other
hazards on public and home playgrounds.
WARNINGS ON ANCHORING
It is highly recommended the product be anchored into the ground to prevent movement and to make the
swing set more stable during use.
Some consumers want an anchoring system that allows the product to be moved to different locations.
Other consumers want to keep their swing set in a permanent location.
There are different types and different methods of anchoring this product. Sportspower does not make a
specific anchoring recommendation as each consumer’s needs and conditions can vary.
It is highly recommended that you seek the opinion from a local licensed contractor on the best way to
secure the swing set in your location. One possible way to anchor a product is to create a concrete footing
and use that as a base for an anchor. Whatever method you prefer for your location, an anchoring system
for this product should be used at all times.
WEATHER CONDITIONS
DO NOT use this equipment if the swing seat, slide or any parts are wet. Use the play set only when the
parts are clean and dry. If the equipment is wet, the user could slip and suffer injuries.
Please be aware of weather conditions when using the equipment. If it is too windy, users could lose
control and suffer injuries. The playground equipment must be properly anchored, stored away or
restricted from use during inclement weather such as heavy winds or severe weather storms. You
should consult a local contractor about ways to anchor the product in your location.
6
PLAY SUPERVISION
DO NOT allow more than one child to play on the individual swing, trapeze or slide component at any
one time.
DO NOT allow children to stand on the slide, swing seats or any other component of the swing set.
DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe distance to avoid being
struck by other children while playing on swings, slides, etc.
DO NOT allow children to twist the swing chains or ropes, or loop them over the top support bar as this
may reduce the strength of the chain or rope.
DO NOT swing empty seats as this may cause injuries.
ALWAYS guide children to sit in the center of swinging parts, with their full weight placed in the seat
center and holding on to the swing chains.
DO NOT allow children to jump off the equipment while it is in motion. ALWAYS come to a full stop
before dismounting.
ALWAYS dress children appropriately for proper play, e.g. wear well-fitted rubber sole shoes, and
remove loose or sharp items such as jewelry, hair accessories, scarves which may become entangled in
the equipment or cause injuries.
ALWAYS make sure children remove their bike or other sports helmets before playing on the
playground.
DO NOT allow children to slide down the slide head first.
DO NOT allow children to climb onto the swing frame or jump to/from different play areas of the
equipment.
ALWAYS return safely to the ground before approaching another play area.
DO NOT allow children to climb on structural parts (e.g. legs, top bar). These are structural components
and are not designed for play.
ALWAYS check the slide or other parts exposed to the body for extreme heat from the sun before
allowing children to use the equipment.
ALWAYS prevent access and secure from any unauthorized use when there is no adult supervision.
DO NOT allow pets or other animals near the equipment to prevent damage or injuries.
7
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION
DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the
equipment and all parts are well secured and stable before each use.
ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially
hazardous to users.
DO NOT attach items to the equipment that are not specifically designed for use with the equipment,
including, but not limited to, jump ropes, clothesline, pet leashes, cables and chains as they may cause
choke hazards.
The steel and plastic parts used in your product are subject to normal wear. Gradual deterioration of the
material will occur, the speed of which will depend on the level of exposure to UV rays, airborne
pollution, outdoor weather conditions such as rain and wind and the amount of use. You must inspect
the equipment prior to every use. This includes, but is not limited to inspecting the set for cracks, excess
wear, missing parts, loose connections, and for overall integrity. When the set shows any signs of
weakness, you must stop using the play set immediately, properly store the set or restrict access by
users until the condition is resolved.
Verify that the suspended climbing ropes, chain or cable are secured at both ends and tightened, so
that there is no loose ropes, chain or cable hanging that can result in choking hazard.
When conducting inspections, it is recommended that you use the Suggested General
Maintenance Checklist and Routine Inspection and Maintenance Issues checklists provided by
the US Consumer Product Safety Commission, a copy of which is contained in this user manual.
CARE & MAINTENANCE INSTRUCTIONS
Inspect all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It
is particularly important that this procedure is followed at the beginning of each season.
Oil all metallic moving parts monthly during the usage period.
Sand rusted areas on metal tubing and repaint using a nonlead-based paint meeting the requirements
of Title 16 CFR Part 1303.
Check swing seats, ropes, cables and chains monthly during usage season for deterioration.
Replacements should be made in accordance with the manufacturer’s instructions.
Check all coverings for bolts and sharp edges twice monthly during usage season to be certain that they
are in place and replace when necessary. It is especially important to do this at the beginning of each
new season.
Do not use when the temperature drops below 32 degrees F (0 degrees C); remove and store the
plastic swing seats and slides indoors.
8
IMPORTANT CONSUMER INFORMATION SHEET
The Consumer Product Safety Commission estimates there are more than 200,000 playground related injuries
involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all
playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface
under and around playground equipment can be a major factor in determining the injury-causing potential of a fall.
It is self evident that a fall onto a shock absorbing surface is less likely to cause a serious injury than a fall onto a hard
surface. Playground equipment should never be placed on hard surfaces such as concrete or asphalt and while grass
may appear to be acceptable it may quickly turn to hard packed earth in areas of high traffic. Shredded bark, mulch,
wood chips, fine sand or fine gravel are considered to be acceptable shock absorbing surface when installed and
maintained at a sufficient depth under and around playground equipment.
Table below lists the maximum height from which a child would not be expected to sustain a life-threatening head
injury in a fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6”
(15.25CM), 9” (22.9CM), and 12” (30.5CM).
However, it should be recognized that all injuries due to falls cannot be prevented no matter what surfacing material
is used.
We recommend that a shock absorbing material should extend a minimum of 6ft in all directions from the perimeter
of stationary equipment such as climbers and slides. However, because children may deliberately jump from a
moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of 2
times the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No
particular material is recommended over another. However, each material is only effective when Properly
maintained. Materials should be checked periodically and replenished to maintain correct depth as determined
necessary for your equipment. The choice of a material depends on the type and height of the playground
equipment, the availability of the material in your area and its cost.
Note: The maximum fall height for this product is 6 feet. The minimum ground Clearance between the bottom of the
suspended plays and the playing or ground service must be 8 inches.
This information has been extracted from the CPSC publication on" Playground Safety". You can obtain more
information by sending a postcard to the: Office of public Affairs, U.S. Consumer Product Safety Commission,
9
Washington, D.C.20207
ANCHORING
(NOTE:ANCHORS ARE NOT INCLUDED - MUST BE PURCHASED SEPARATELY)
There are different ways of anchoring the equipment, depending on the type of ground on which the
equipment is to be installed. Make sure that all anchors are below ground level to prevent tripping.
You should consult your local contractor to decide the most appropriate way to anchor the
equipment in your location.
The following anchoring options may be considered:
Corkscrew Anchoring (Corkscrew Anchors not included)
If your soil is hard (clay, etc.), the corkscrew method may be suitable.
Be sure that the swing set is located on level ground.
Twist the corkscrew anchor into the ground until only the end with the hook is above the ground
and next to the leg. Insert the hook into the bottom opening of the leg.
Ensure that the hook is secured onto the leg opening.
Concrete Anchoring (Materials not included)
● If the swing set is set up on grounds with sandy soil (soft) condition, it must be anchored
with concrete footing (concrete not included)
● Be sure that the swing set is assembled and placed on level ground
● Dig holes around swing leg tube, as shown in drawing in the next page. As you dig
deeper, enlarge the diameter of the hole to fix the cement
● Place 2 inches of brick or gravel underneath the leg, as shown in drawing in the next
page
● Use about 45 lbs. of concrete per leg
● Cover the concrete with dirt and protective surface material
● Allow 6-7 days for the concrete to dry properly
10
Note: The maximum fall height for this product is 6 feet. The minimum ground
clearance between the bottom of the suspended plays and the playing or
ground surface must be 8 inches.
You must maintain a minimum of 8 inches of ground clearance.
WARNING
Please properly anchor the swing set to minimize the risk of injury or death.
If the swing set is used without proper anchoring, it may be dangerous and
may tilt over.
FRAME
CONCRETE
BRICK OR GRAVEL
2”
12-5/8”
5”
11
CARE AND MAINTENANCE CHECKLIST
AT THE BEGINNING OF EACH PLAY SEASON:
Tighten all hardware.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or
missing.
Check all moving parts including swing seats, ropes, cables and chains for wear, rust or other deterioration.
Replace as needed.
Check metal parts for rust. If found, sand and repaint using a non-lead paint meeting the requirements of 16
CFR 1303.
Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain
appropriate depth. Replace as needed.
TWICE A MONTH DURING PLAY SEASON:
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges and corners. Replace if they are loose, cracked or
missing.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain
appropriate depth. Replace as needed.
ONCE A MONTH DURING PLAY SEASON:
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all moving parts including swing seats, ropes, cables and chains for wear, rust or other deterioration.
Replace as needed.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain
appropriate depth. Replace as needed.
AT THE END OF EACH PLAY SEASON:
At the end of each play season or when the temperature drops below 32 degrees F (0 degrees C).
Remove plastic swing seats and other items as specified by the manufacturer and take indoors or do not use.
Rake and check depth of loose fill protective surfacing materials to prevent compaction and to maintain
appropriate depth. Replace as needed.
As a general rule, maintenance should be performed at any time it is deemed necessary.
DISPOSAL INSTRUCTIONS
Please use care when disassembling the equipment, when it is no longer in operational condition. Wear
heavy duty working gloves to avoid injuries.
Fully disassemble the entire swing and slide sets before disposal. Do not leave partially disassembled parts in
areas accessible by children.
Should you wish to recycle the steel tubing, please take the frame to your local recycling center.
All plastic parts can be recycled, take it to your local recycling center. Do not let children play with any
disassembled parts meant for disposal, such as chains, slide, tubing, bolts, nuts, screws, etc.
All rusted parts, bolts must be properly disposed of in trash bin. Do not reuse.
Owners shall be responsible for maintaining the legibility of the warning labels.
12
TOOLS NEEDED
Please prepare the following tools prior to assembling this equipment.
Hammer
(May be needed for installing anchor)
(Not included)
Flat and Philips Head Screwdriver
(Not included)
Tape Measure (Not included)
Special Socket Wrench (Included)
Wrench (Included)
Wrench (included)
Small Allen wrench (Included)
Big Allen wrench (Included)
13
PARTS LIST
Parts List for Main Frame
Parts List for Swing Seat
Part No.
Picture
Description
Quantity
A1 RIGHT TOP BAR
1
A2 LEFT TOP BAR
1
A5 BOTTOM SECTION LEG
6
A6
CROSS BARF
2
A7 CROSS BAR (FOR SLIDE)
1
C2 END CAP (PRE-ASSEMBLED)
2
B1 BOLT 5/16”*2.5” (8mm*64mm)
14
B3 NYLON NUT 5/16”
14
B4
PLASTIC CAP (WITH ARC WASHER)
14
B5 ARC WASHER 5/16’’ (8mm)
8
B6 FLAT WASHER 5/16’’ (8mm)
6
Part No.
Picture
Description
Quantity
J1
PVC COVERED CHAIN
(PRE-ASSEMBLED)
4
J3
EYE BOLT WITH ATTACHMENT BOLT
(PRE-ASSEMBLED)
4
K1
SWING SEAT
2
J6 NYLON NUT 5/16" (8mm)
4
J8
PLASTIC CAP
(CURVED FOR ARC WASHER)
4
Loading...