Split Phantom ULB21, ULB24 Installation And Instruction Manual
INSTALLATION AND INSTRUCTION MANUAL
The Split Phantom
The Split Phantom
Undercover Interior LED Lightbar
Models
ULB21 ULB24
(Discrete) (Gen 4 Starburst)
™
IMPORTANT: Please read all of the following instructions before installing your new warning light.
PLIT390 REV. F 10/16/12
Due to continuous product improvements, we must reserve the right to change any
NOTICE
specifications and information, contained in this manual at any time without notice. Star
Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual,
including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or use of
this manual.
IMPORTANT: Please read all of the following instructions before installing your new
CAUTION: Please be sure to check that your cigarette plug outlet is properly fused. Testing the
WARNING!!!! Care should be taken when positioning this warning light so that the light and/or
Please Note: These instructions are provided as a general guideline only. Specific
mounting and/or wiring, may be necessary and are the sole responsibility of the
installer. Star Headlight & Lantern Co., Inc. assumes no responsibility for the
integrity of the installation for this or any of its products.
light before this fuse is properly installed will void the warranty on the light.
Split Phantom
cord does not interfere with the proper operation of the driver-side or passengerside airbag! Failure to heed this warning may result in serious or fatal injury.
™
LED undercover lightbar.
The Split Phantom
™
uses state-of-the-art Light Emitting Diode (LED)
technology. This warning light is comprised of ultra-high intensity LEDs that
are operated by a micro-controller to efficiently produce light output with
lifetimes up to 100,000 hours.
CAUTION: All of our DC powered warning lights are polarity
sensitive. These lights are polarity protected only if the
appropriate fuse is used. All wires connected to the positive
terminal of the battery should be fused at the battery for their
rated load. Testing the light before this fuse is properly
installed will void the warranty on the light.
-1-
Optional Mounting Brackets
There are several optional mounting brackets that can be used to mount your
Split Phantom
the light was ordered.
Please Note: Every ULB21 comes with a standard baffle included. The 274-ULB21-CH
and 274-ULB21-CH11 kits also include a separate baffle that is specifically designed to
fit the Dodge Charger. It should be used in place of the standard baffle included.
™. Your light comes with the one that was selected at the time
274-ULB21-U1 Universal Mounting Kit
274-ULB21-CH 2006-2010 Dodge Charger
2007-2008 Dodge Magnum
2009 Dodge Ram
274-ULB21-CH11 2011 Dodge Charger
274-ULB21-CP 2011 Chevrolet Caprice
274-ULB21-CV 2006-2011 Ford Crown Victoria
2009 Ford F150 and F250
274-ULB21-EX 2006-2010 Ford Explorer
2007-2010 Ford Expedition
274-ULB21-IM 2008-2010 Chevrolet Impala
274-ULB21-INT 2012 Ford Interceptor (Taurus)
274-ULB10-RM 2012 Dodge Ram 1500
274-ULB21-TA 2007-2011 Chevy Tahoe
2007-2011 Chevy Yukon
2007-2011 Chevy Suburban
Star Headlight & Lantern Co., Inc. assumes no
responsibility for the secure mounting of this light. It is the
responsibility of the installer and/or owner to ensure the
lightbar is mounted securely. Check your light every time
you enter the vehicle to ensure that it is mounted securely.
-2-
Mounting Instructions
The following mounting instructions describe the standard, most
common way to mount this light. This method may or may not apply to
your vehicle. Because vehicles can vary widely in their design, it may be
necessary to configure the brackets differently than described. Some
applications may require you to design your own custom brackets. The
installer assumes all responsibility for the integrity of the installation. It is
the sole responsibility of the owner to ensure the light is secure.
The
Split Phantom
of your vehicle. It is not intended for exterior applications and is
not warranted against water damage.
It is the sole responsibility of the owner to ensure the warning light is
secure. Check your light every time you enter the vehicle to ensure that
it is mounted securely. The manufacturer assumes no responsibility for
the secure mounting of this light.
The ULB21 is designed to be mounted in the front windshield of a vehicle using
both of the pre-existing visor clips. An alternate method is also shown using the
Universal Brackets.
™
is designed to be mounted on the inside
Before installing any of the
brackets, slide the enclosed
rubber channel over the
front edge of the baffle .
-3-
The mounting instructions are divided into two separate sections. If you
are using the Universal Mount, proceed below. If you will be using one of
the vehicle specific brackets, please skip to page 9.
UNIVERSAL BRACKET INSTALLATION
(Model 274-ULB21-U1)
OR
OR
SUCTION CUP
OR
WINDOW ADHESIVE
MOUNT
•
Two different sets of forked brackets are provided. Use the pair of forks
that will require the least amount of adjusting when aligning the light with
the window.
•
The Universal Mount uses either pair of forked brackets, in conjunction
with either a pair of suction cups or a pair of window adhesive mounting
pads (both included).
•
The Forked Brackets must be installed for both the suction cup and
window adhesive mounts.
•
Determine if you can install the Forked Brackets under your visor clips or
if you need to attach them in an alternate fashion and refer to the
appropriate section on pages 6 or 7.
-4-
Loading...