SPLENDID WD 2100 XC (NA).1 User Manual
210
C
oX
Contents
General information, 1-2-3-4-5
Technical Information, 2-3
Important Safety Instructions, 4
Introduction, 5
Installation requirements, 6-7
Attention / Grounding instructions, 6
Electrical, location and draining, 7
Installing the washer-dryer, 8-9-10-11
Unpacking the washer-dryer, 8
Removing the transit screws, 8
Connecting the water inlets, 9
Connecting the drain hose, 9
Installing the exhaust ducting, 10
Leveling the washer-dryer, 10
Completing the installation, 11
About your appliance, 12-13-14-15
Washer-dryer special features, 12
Control panel, 13
Option buttons, 14
Program key, 14
Detergent and laundry aids, 15
Dispenser drawer, 15
Washing and drying, 16-17-18-19
Cycle Description Chart, 16
Before starting a cycle, 17
Determining load sizes, 17
Setting a wash, dry or wash-to-dry cycle, 17
Splendide laundry tips, 18
For best results, 18
Combo laundry FAQs / Sample loads, 19
Care and maintenance, 20-21
Turning off the water or electricity supply, 20
Cleaning the dispenser drawer, 20
Checking the water inlet hoses, 20
Cleaning the pump pre-chamber, 21
Checking the dryer vent, 21
:';&1$
Troubleshooting, 22-23
Troubleshooting Chart, 22
If you need assistance, 23
General Information
This appliance was tested by UL and
conforms with both Canadian and U.S.
UL safety requirements and displays
their mark.
2 General Information
Technical information
S
p
eigh
s
(59.5 cm
)
5
(84.5-85.7 cm
2
(55.9 cm
)
m
s
0
1
y
)
g
C
onn ection
u
u
S
p
S
p
g
d
d.
Model WD2100XC(NA)#
imension
inimum Installation
C
learance
apacit
E
lectricalConn ection
ax
.
in
eed
in
. I
nstallation
pacin
lendide 2100XC(NA)#
th: 23.4”
Height: 33.25-33.7
epth: 2
Sides:
nt / Back:
)k
Max. Absorbed Power: 1300 Watts
Max.Pss
ss
p to 1200 R
is appliance may be installed in a recessed area, closet or alcove. The installation
spacing is in inches and is the minimum acceptable. *Additional spacing should be
onsidered for easy installation, servicing and compliance with local codes an
rdinances. Installations must conform with the minimum dimensions indicate
ryerExhaust
Requirements
NOTE: The manufacturer reserves the right to make any improvements to its appliances without giving prior notice.
General Information 3
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of fire, electric shock, or
injury to persons when using your appliance, follow basic
precautions, including the following:
• Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
• Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
• Read all instructions before using any appliance.
• Do not wash or dry articles that have been previously
cleaned in, washed in, or spotted in gasoline, dry cleaning
solvents, or other flammable/explosive substances as they
give off vapors that could ignite or explode.
• Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
• Before the appliance is removed from service or
discarded, remove the door to the washing/drying
compartment.
• Do not add gasoline, dry-cleaning solvents or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
• Do not install or store this appliance where it will be
exposed to the weather.
• Do not tamper with controls.
• Under certain conditions, Hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the appliance, turn on all hot-water
faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas.
As the gas is flammable, do not smoke or use an open
flame during this time.
• Turn off water faucets to relieve pressure on hoses and
valves and to minimize leakage if a break or rupture
occurs.
• Do not reach into appliance if the drum is moving.
• Repair or replacement of a part should be made only by
a qualified service technician to prevent personal injury or
damage to the machine. Contact Splendide to locate an
authorized repair service company near you.
• Good, safe practices and caution MUST be applied when
installing, operating, and maintaining any appliance. Follow
basic precaution.
• Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
• Disconnect power to the washer at the circuit breaker or
fuse box, or unplug the machine in an emergency or when
servicing is required. Have the installer show you and label
the proper switch or fuse at the electrical disconnect box.
• The interior of the appliance and exhaust duct should be
cleaned periodically by qualified service personnel.
• Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
• Before loading the washer, make sure the drum is empty.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock by
providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes
and ordinances.
WARNING - Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative or
personnel if you are in doubt as to whether the appliance is
properly gounded.
• Do not repair or replace any part of the appliance or
attempt any servicing unless specifically recommended in
the user-maintenance instructions or in published userrepair instructions that you understand and have the skills
to carry out.
4 General information
Do not modify the plug provided with the appliance: if it will not
fit the outlet, have a proper outlet installed by a qualified
electrician.
Congratulations
Introduction
Congratulations on your purchase of a
Splendide. Your Spendide washer-dryer takes
the drudgery out of doing laundry - simply toss
dirty laundry in and get clean, dry laundry out!
Whether its installed in a luxury RV, yacht, or
apartment closet, your new Splendide is
designed to fit where others wont and deliver
outstanding washing and drying performance
(all while conserving more energy and water
than other brands). Enjoy your new Splendide!
Read this manual
Please read this manual carefully. If you need
further assistance, please contact Splendide
For your records
Write model and serial numbers here. You can find
them on the front of the machine and inside of the
door opening.
Model: i.e. WD2100XC (NA)#
Serial No:
S/N
Laundry Centers (Mon-Fri 7am- 4:30pm PST)
1-800-356-0766
General information 5
Installation Requirements
O
TENTI
!
WARNING
ELECTRICAL SHOCK HAZARD
Disconnect power before servicing.
Replace all panels before operating.
Failure to do so can result in death
or electrical shock.
6 Installation requirements
Electrical
• Machine Voltage/Amperage - 120V, 60 Hz,
1300 W, 11 Amp.
• Connection - 3-prong plug with 6 cord is
provided with the machine.
• Circuit/Protector - 3-wire single phase, 120V,
60 Hz, AC, on a separate 15 Amp circuit.
Location
• This machine may be installed free
standing as well as in a recessed area,
closet, or alcove
• Minimum Installation Spacing - 0 on
sides and 1 in front and back. NOTE:
Additional installation spacing needs to be
considered for easy installation, servicing,
and compliance with state and federal
codes.
• Floor - Must support at least 280 lbs. and
be a solid, level surface. DO NOT install on
carpet.
• RV/Marine Installations - When locating
the appliance in a towable trailer or
watercraft, position the machine over the
axles or mid-ship where movement is at a
minimum. Block the machine to prevent
extreme movement.
If you have... You’ll need...
no access to Hot/Cold
water hookups
to install a dryer vent
and ducting in your RV
or boat
concerns about the
appliance shifting in
your RV or boat
water damage concerns
to make a 90” duct turn
in less than 4.5”
Splendide Faucet Adapter
Kit, or equivalent.
Splendide Vent Kit, or
equivalent.
Splendide SecureFit bracket
kit, or equivalent.
Splendide Drain-A-Way Pan,
or equivalent.
Splendide 90˚ oset elbow, or
equivalent.
Drainage
Standpipe Diameter/Capacity - Needs a 1.25 ¼
minimum diameter standpipe with a minimum
carry-away capacity of 7 gallons per minute.
Top of Standpipe - Must be between 25 and 34
high from the bottom of the machine.
Outlet End of Drain Hose (provided with the unit)
- Must be at least 20 above the bottom of the
washer-dryer. An air break must be available at the
standpipe to avoid siphoning. No more than 6 of
the drain hose should be inserted into the drain
pipe to prevent siphoning.
• Exhaust Requirements - Rigid or flexible
metallic duct required. Ducting should be
as short and straight as possible. DO NOT
exhaust dryer into a chimney, furnace, cold
air duct, attic crawl space, or another duct
used for venting. If a cabinet door is
installed, a minimum of 8 sq. in. should be
provided for make up air. Louvered doors
with equivalent air openings are
acceptable. Allow clearances behind
door(s) to avoid rubbing between back of
cabinet door(s) and front of unit control
panel. Additional clearances for wall, door
and floor moldings may be required.
Installation requirements 7
Installing the washer-dryer
Unpacking the washer-dryer
• Carefully remove the packing materials with care
not to damage the drain hose and power cord
that are shipped installed on the machine.
Check that the machine is intact. Report any
damage immediately.
• Position the washer-dryer near the desired
installation position.
WARNING! Plastic bags, styrofoam, nails and
other packaging parts are not children’s toys and
can be potentially dangerous. Destroy the carton
and plastic bags after the washer-dryer has been
unpacked.
IMPORTANT: Retain the transit screws, spacers
and rubber tubes. These items should be
reinstalled to prevent damage if or when you
transport the machine in the future.
Connecting the water inlets
If the water pipes you will be connecting to are new
or unused, run the water until clear to remove any
debris that could clog the water valve screens or
valves before connecting the machine. NOTE: Supply
shut-off valves should be easily accessible.
IMPORTANT: Water pressure MUST range within
the values indicated on the “Technical Data”
chart
Removing the transit screws
For transportation, the inside of the machine is
supported by screws, rubber grommets and spacers
on the back panel. Before using the washer-dryer,
these items MUST be removed.
IMPORTANT: Transit screws and spacers must be
removed before operating the machine to allow
proper operation of the machine and to prevent
damage to the appliance.
• After positioning
the washer-dryer
near the
installation
location, remove
the four screws
(Fig.1), with the
rubber grommets
and plastic spacers
that are attached
to them.
• Use the plastic plugs (provided in the accessories
bag) to fill in the holes.
Fig 1
• Included in the accessories supplied with your
machine are 2 inlet hoses with 4 rubber washers
pre installed. Check that the rubber washers are
installed in the ends of the inlet hoses to make a
water tight seal at each connection point.
• Connect the straight ends of the water inlet
hoses to the supply taps that have .75BS
thread (standard hose bib).
• Connect the 90º angled ends (20 mm thread) of
these hoses to
the inlet valves
on the back of
the machine (Fig.
2). NOTE: Water
Inlet valves are
color coded:
Red (Hot) &
White (Cold).
IMPORTANT: Do not use excessive force.
Damage to the couplings can result. The
couplings should be tightened by hand; a tool
should only be used if a leak occurs.
H
C
Fig 2
8 Installing the washer-dryer
Connecting the drain hose
It is possible for the water to be discharged into a
sink, standpipe or drainpipe, but an air break must be
available at a minimum 20 height to prevent the
machine from siphoning (Fig. 6).
Floor Standpipe Wall Standpipe
A
B
A & B = 25" (62 cm) min. / 34" (86 cm) max.
Standpipe Drain System - Installations require a
minimum 1.25 ¼ (3.2 cm) diameter standpipe with a
minimum carry away capacity of 7 gallons (26 liters)
per minute.
Wall or Floor Standpipe Drain System - The top of the
standpipe must be between 25 (62 cm) - 34 (86
cm) from the bottom of the washer (Fig. 4).
Fig 4
IMPORTANT: Make sure that the drain hose is not
kinked and that water ow is not restricted.
method. 2) directly to a Y branch tail piece
(available at most hardware stores). 3) Through the
floor to a separate trap. The trap must be vented to
prevent siphoning. To provide proper venting, install
an Air Gap Kit (available at most hardware stores). 4)
&RQQHFW WR WKH IDXFHW XVLQJ D )DXFHW $GDSWHU .LW
DYDLODEOHVHSDUDWHO\
• Use a U-Clamp (provided in your accessories
packet) or suitable item to secure the outlet end
of the drain hose (pre-installed on the back of
your machine).
• Insert the outlet end of the drain hose into the
standpipe, wall or floor drain (Fig. 6). NOTE:
The outlet end of the drain hose MUST be at
least 20 (50 cm) above the base of the
machine. No more than 6 of the drain hose
should be inserted into the drain pipe to prevent
siphoning.
• Use a strap, cable tie, or similar item to hold the
hose or the U-Clamp in place.
Sink Drain W/ "Y" Branch Tailpiece
25" (62 cm) min.
with an air break
Laundry Sink Drain
Fig 5
Sink Drainpipe System - Entry into the sink drain
system must be above the trap (Fig. 5). When routing
the drain hose through cabinets or walls, use a
protective material such as electrical or duct tape to
cover sharp edges that could damage the drain hose.
Use a suitable clamp to secure the drain hose to the
Y branch or the disposer (Fig. 7). With a sink
drainpipe system, you may connect directly: 1) to a
disposer by following the manufacturers attachment
Floor Standpipe
Floor Standpipe w/ "Y" Branch Tail Piece
U-Clamp
Cable tie
"Y" Tail Piece
This connection MUST be
before drain trap and at
least 20" (50.8 cm) above
the floor where washer will
be installed.
20" (50 cm) min.
with an air break
Standpipe
6" max.
20" (51.8 cm) min.
34" (86 cm) max.
Standpipe
25" (62 cm) min.
34" (86 cm) max.
Fig 6
Fig 7
Installing the washer-dryer 9
Installing exhaust ducting
WARNING! To reduce the risk of re, this
appliance must be exhausted to the outdoors.
IMPORTANT:
This appliance should
NOT be exhausted into a
chimney, wall, ceiling, or
any concealed space of a
building. Only rigid or
exible metallic ducting
should be used.
Fig 8
• Rigid or flex metal/metallic ducting should be
used.
• Exhaust ducts should be as short and straight as
possible. NOTE: Long exhaust ducting can
extend drying time, collect lint and may affect
drying performance.
• The exhaust duct must end with an approved
exhaust vent hood with swing out damper(s) or
tailpiece with louvers.
• Check that all ducting is clean and lint free. Use
duct tape or screw clamps to secure all joints.
• Use duct tape or screw clamps to secure the
duct to the round flange vent located on the
back of the machine (Fig. 8).
Rigid or exible metallic duct required. Ducting
must be as short and straight as possible.
Do not exhaust dryer into a chimney, furnace,
cold air duct, attic crawl space, or another duct
used for venting.
If a cabinet door is installed, a min. opening of 8
sq. in. should be provided for make up air.
Louvered doors with equivalent air openings are
acceptable. Allow clearances behind door(s) to
avoid rubbing between back of cabinet door(s)
and front control panel. Additional clearances for
all, door and oor molding may be required.
Leveling the washer-dryer
• To access the front
leveling legs, tilt the
machine backwards,
leaning it against a
wall or other stable
structure.
• Adjust the legs up
or down (Fig. 9) to
ensure the washer is
resting solid and
does not rock side-to-side or front-to-back
when the machine is upright.
Fig 9
10 Installing the washer-dryer
IMPORTANT: The machine must rest solid on a
sturdy oor for optimum performance and
minimum vibration.
Completing the installation
• Check the electrical requirements. Be sure
that you have the correct electrical supply
and the recommended grounding method.
• Check that the shipping brackets have been
removed.
• Check that the water faucets are ON.
• Check for leaks around faucets and inlet
hoses.
• Plug washer into a grounded 3-prong outlet.
• Slide the washer-dryer to its final location
and confirm that its level.
• When installing this appliance in an RV or
marine vessel, you should block in the unit
to prevent it from shifting or tipping. A
SecureFit Bracket Kit is available from
Splendide to keep the unit from shifting
front-to-back or side-to-side.
• Test and clean the washer. Run a test load
with no laundry.
Testing and cleaning the washer,
• Press the ON-OFF button to turn the washer
ON
• Pour 1 to 2 TBSP of powder detergent into
the detergent dispenser compartment 2
• Select wash program 2.
• Make sure the DRY TIME knob is in the OFF
position.
• Then press START. Allow the washer to
complete the wash cycle.
Installing the washer-dryer 11
About your washer-dryer
WARNING - To reduce the risk of fire, electic shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
To reduce the risk of electric shock,
DO NOT remove cover (or back). No user
serviceable parts inside. Refer servicing to
qualied service personnel.
The lightning ash with arrowhead
symbol, with-in an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sucient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
after every wash (except Express Wash) and features an Extra
Rinse button that adds yet another rinse to remove even
more dirt/detergent from fabrics (recommended for those
with detergent contact allergies).
Foam Removal System
Your machine automatically measures the amount of foam
in circulation and adds water to the drum to remove excess
foam for the highest rinsing performance.
Recirculating Wash Feature
With your Splendide washer-dryer, no detergent is wasted.
Water recirculates and redistributes detergent throughout
the drum in a way that assures all detergent is dissolved for
max. resource efficiency.
Automatic Balance System
Every Splendide washer-dryer incorporates the latest motor
technology. When it detects an out-of-balance load the
motor will adjust speed (or come to a complete stop) and
reposition the load automatically.
Impulse Spin Technology
Your machine features Splendides exclusive IST processor
that varies pulse in low spin for less wrinkling, less wear on
clothing, less noise, less vibration, and improved energy
efficiency.
Your New Appliance
Your new appliance is an automatic washer and vented
tumble dryer by Splendide. Front-loading with a stainless
steel drum and an extra large door opening for easy loading
and unloading. It features 10 wash programs, 7 water temp.
settings, 3 dry programs, and a 1200 RPM max. spin speed.
Automatic Dispenser Drawer
Automatically dispenses laundry aids (detergent, bleach,
softener) during the cycle.
Auto Water/Energy Control
Automatically adjusts the amount of water and energy to
use for each load.
Safety Door Lock
Protects you from opening the door when it is unsafe.
Express Wash
Washes lightly soiled Cotton Heavy Duty and Permanent
Press fabrics in less time.
More Rinse Cycles
Most washers have only 1 rinse following each wash while
your Splendide washer-dryer has up to 4. It rinses 2-3 times
Extra-Large Door Opening
For easier loading and unloading.
1200 RPM High Spin
For better drying performance.
Extra-Durable
Heavy duty springs, shock absorbers. Stainless steel drum.
Dryer Cool Down
The last few minutes of the dry cycle, your dryer will carry
out a cool down period. Clothing will tumble freely without
heat. This will cool fabric, buttons and snaps for safe
handling and to reduce wrinkling.
Low Maintenance
Lint passes safely through a self-cleaning pump and then
out the drain or dryer vent - so theres no messy wash or
dry filter for you to clean.
12 About your appliance
Description of the control panel
OPTION
Buttons
DOOR LOCK
LED
STATUS LED’s
ON /OFF (Door Open) Button
Turns power to the washer ON or OFF, unlocks the
door during the wash and dry cycles.
Note: if the button is pressed during the cycle the
door will open only whether allowed by safety
conditions.
ON/OFF
CYCLE
Selector
DRY TIME
Selector
START
WASH TEMP
Selector
OPTION Buttons
Use these buttons to modify the wash cycle (see
Description of Option Buttons, page 12) .
STATUS LEDS
Indicates the cycle phase thats underway.
DOOR LOCK LED
Indicates when the door is locked and when it can
be safely opened:
SOLID=Locked, F LASHIN G =Unlocked
To unlock the door: Press the ON/OFF button.
To resume the cycle: Close the door and press
the ON/OFF button again.
START (Cancel) Button
Press once to START the program, or press and
hold to CANCEL a program in progress. Also, press
to finish the SILK cycle after its gone into Anticrease/soak.
IMPORTANT: The rapid ashing of the DOOR
LOCK LED together with ashing of atleast one
other LED indicates an abnormality (see Troubleshooting)
DRY TIME Selector
Use this knob to select the desired drying minutes.
MAX LOAD will dry for 180 minutes and is
recommended for full, 11 pound loads.
WASH TEMP Selector
Use this knob to select the water tempurature
(when a WASH cycle is selected. NOTE: Rinse water
is always COLD.
CYCLE Selector
Use this knob to select a WASH or DRY cycle.
About your appliance 13
Description of the Option Buttons
You can customize the wash by adding an OPTION or combination of options
to your cycle selection. The button corresponding to the OPTION selected will
remain LIT. NOTE: If you push an OPTION button and it flashes, that means
the OPTION you selected is not available for that cycle.
Low
Heat
EXTRA RINSE - Adds an extra rinse
to the wash cycle (Not available in
Delicates)
LOW SPIN - Reduces the high spin
speed to 600 rpm (Not available in
Delicates). NOTE: This option is not
available if a Dry cycle is set.
Pre
Wash
Extra
Rinse
LOW HEAT - Increases the duration
of the cooling period for the selected
dry cycle.
PRE-WASH - Adds an extra fill at the
beginning of the wash cycle
Low
Spin
Description of the Program Key
The front of the dispenser drawer contains a Program Key to help you select a
Wash or Dry Cycle using the Cycle Selector Knob.
14 About your appliance
Optional
All-Natural, HE
•
detergent formulated
for your washer-dryer
Softens fabrics
•
naturally
While not required, Splen dide recommends the use
of a High Efciency (HE)
detergent. HE detergents
are quick dissolving and
low sudsing and will deliver
optimum results in your
front-loading machine.
Splendide Premium
Laundry Powder,
Part No. 1005
About the Dispenser Drawer
Laundry Aid Type / Amounts
Your Splendide requires smaller amounts of laundry
aids to get fabrics clean. Adding too much
detergent wont necessarily make for a more
efficient wash, and may in fact cause build up on
your clothes and inside your appliance and even
pollute the environment. Recommended laundry
aid amounts per wash load:
• Prewash detergent (Optional):
1 to 2 TBSP Powder
(or 1 TBSP Liquid)
Laundry products are diluted and dispensed
automatically at the proper time during the wash
cycle. The dispenser drawer has three
compartments (plus one removable bin) for adding
laundry products to the wash load. These
compartments are:
4
3
2
1
1 PreWash Detergent (With Bleach Bin
removed)
2 Detergent for the Wash Cycle
(Powder or Liquid)
3 Fabric Softener (Liquid)
4 Bleach (With Bleach Bin in place)
NOTE: Bleach option available in
cycle 1 (Super) wash ONLY
• Detergent:
1 to 2 TBSP Powder
(or 1 TBSP Liquid)
• Fabric softener:
1to 2 TBSP (Liquid ONLY)
• Bleach (Optional):
DO NOT exceed the MAX fill line
IMPORTANT: Adjust laundry aid amounts for
heavily/lightly soiled loads, or hard/soft water.
NEVER EXCEED the recommended amounts of
detergent or fabric softener. Doing so could
impair wash results and cause damage to the
internal parts of your machine!
IMPORTANT: NEVER USE FABRIC SOFTENER
SHEETS!
WARNING! Always dilute bleach before using.
Never overfill bleach dispenser. Excess bleach
could damage clothes.
IMPORTANT: The suds level should never rise
more than half way up to the porthole. Too much
foam will rise through the dispenser and make a
mess on your floor
IMPORTANT: Using fabric softener causes items
to release from the drum immediately after
high-speed spin, helping clothes to dry faster
while minimizing wrinkling and softening fabrics.
NOTE: Splendide recommends using 1 to 2 tbsp.
of a bio-friendly, or similar brand per wash load.
These softeners tend to appear light in color and
dissolve more quickly in less water, minimizing
build-up within your machine.
About your appliance 15
e
e
y
s
y
e
y
i
s
y
cs
y
y
s
pi
e
f
l
o.
r
t
e
e
c
r
s
e
gth
e
n
ach
e
ash
ash
s
s
e
n
cs:
,
,
,
.
d
cat
cs:
,
.
d
y
cat
cs
cs
cs
Y
n
d
y
d
y
d
d
y
d
y
d
y
d
d
d
d
at
ash
e
eat
se
at
se
at
at
at
at
h
se
se
at
at
se
00
.
.
.
.
.
.
.
0to 180
.
.
0to 180
.
.
.
.
.
to 4
.
.
.
,
s
n
.
.
y
)
m
e
y
automati
y.
y
y
OTE
p
y
n
n
t
0to 180
n
)
Washing and drying
Cycle Description Chart
Fabric typ
Degree o
i
N
Cotton Heavy Duty Cycle
Exceptio
Heavy cotton
fabri
i.e. sheets, socks
towels, jeans
underwear
sweatshirts, etc
ally Soile
Heavil
ile
ile
Lightl
ile
Permanent Press Cycle
Heavil
Synthetic, light
nan
more deli
fabri
i.e. button-ups
khakis, rayon
shirts, etc
ile
ile
e
Lightl
ile
Lightl
ile
Cycle Selecto
Cycl
Nam
Sup
H
Regular
Expe
H
Regular
Del
9 Expe
heti
Detergen
Pr
W
during c
W
NOTE:A high spin is carried out
cle 5 (Cotton Dry 180 min.
*NOTE:
Fabri
ftene
Ble
Option
Availabl
Low He
Extra Rin
Low Spin
Pre Wash
Low Hea
t,
Extra Ri
Low Spin
Low Heat,
Extra Rinse
Low Heat,
Pre Wash
Extra Rinse
Low Spin
Low He
Low He
Pre Was
Extra Rin
Low Spi
Low He
Pre W
Extra Rins
Low Spin
Low He
Low Spin
Low He
nse
Pre Wash
Len
1
min
73 min.
min
2
min
70 min
min
min
min
2
min
cle
min
Cycl
Descriptio
Timed drying
Timed drying
Gentle Cycl
particularl
eli
e fabri
Wool fabri
Wool fabri
ilkan
ile
ile
NL
il*
Extra Rin
Low H
Extra Rin
Low Spin
Low He
45 min
50 min
2
min
About Rinse, Spin and Drai
: When using liquid fabric
Cycle lengths may var
according to water pressure,
load size and fabric t
* Silk cycle cannot be set to go
wash-to-dr
from
call
pe
in
S
N
softener, it is dis
automaticall
NOTE: High spin speed varies
depending on the cycle you choos
Drains any water from the dru
during the rinse cycle
ensed
1RWH:KHQVHOHFWLQJD'U\F\FOHRQO\XVHPLQXWHWLPHVIRUEHVWGU\LQJSHUIRUPDQFH
16 Washing and drying
Low He
Extra Rin
Low Spi
Low Spin
Low Hea
min
16 min
1
min
Wash cycle, rinse
cycles, anticrease
nd DrainONLY
NOSPINCYCLE
Wash cycle, rinse
spin cycle
cycles
800 rpm high spi
Timed drying
Cotton rinse cycle
and spi
(1200 rpm high spin
DrainONLY
NOSPINCYCLE
Before starting a cycle
Always make sure,
the drum is loaded correctly (see below)
•
the door is closed
•
the ON-OFF button has been pressed and machine
•
power is ON
laundry aids have been added to the Dispenser
•
Drawer (see below)
IMPORTANT: DO NOT attempt to open the door
when the ‘Door Lock’ LED (D) is LIT SOLID!
Bleach
(with bin)
Prewash
Detergent
(without
bin)
1 to 2 TBSP
Powder
Detergent
(or liquid
equiv.)
*
1 to 2 TBSP
Liquid
Fabric
Softener
Setting a
1) Select the wash cycle
wash-to-dry
cycle
• select a washing cycle using the Cycle Selector;
• select the wash water temperature using the
WASH TEMP knob;
• press available OPTION buttons (optional);
2) Select the dry time
• select the length of drying time with the DRY
TIME knob; (NOTE: Average loads will dry in 90
to 120 minutes)
3) Press the START button. When the wash cycle
ends, the appropriate dry cycle will start
automatically
Setting a
1) Select the wash cycle (See above);
2) Select the dry time
wash
cycle
• set the DRY TIME knob to OFF;
Determining load sizes
Maximum WASH CYCLE capacity - Cottons: 15 lbs
Synthetics: 7.5 lbs, Silk: 3.5 lbs, Wools: 3.5 lbs.
Maximum DRY CYCLE capacity - Cotton: 11 lbs.
Synthetics: 7.5 lbs - Wools: 3.5 lbs
Always allow space for air to flow around the
clothes when drying. In general, if your drying,
dont fill the drum more than 1/2 to 3/4 full.
3) Press the START button. When the wash cycle
ends, the machine will stop.
Setting a
1) Select the dry cycle
dry
cycle
• set the Cycle Selector to position 5, 10, or 13;
For best drying performance use 20-120 minutes.
2) Select the dry time
• select the length of drying time using the DRY
TIME knob (20 to 180 min.);
3) Press the START button. When the dry cycle
ends, the machine will stop.
Washing and drying 17
Combine large and small items in one full load.
When washing single items such as a sweater,
towel or jeans, add 1 or 2 similar items to help
balance the load. Single, heavy items such as a
bathrobe can be washed separately.
Do not wash rugs that could come apart and
clog your machine.
For more delicate garments protect underwear,
tights, stockings and other small or delicate
items by placing them in a mesh laundry pouch
while washing and drying.
When using the ‘Wool’ cycle, for best results,
use a detergent that is for wool garments,
taking care not to wash more than 2.2 lbs.
Splendide laundry tips
• Wash cycles are 35 to 100 minutes.
• Dry times for average sized loads are 90 to
120 minutes
• Wash cycles use 7 to 18 gal. of water. YOU
MAY NOT SEE WATER IN THE DRUM. This is
normal.
• The door automatically locks during the wash
and dry cycles. To unlock the door, access the
drum, then RESUME the cycle, see DOOR
LOCK LED on page 13.
For best results,
• DONT OVERLOAD THE DRUM. Keep up with
laundry by doing smaller loads every day or
two.
• DONT EXCEED RECOMMENDED DETERGENT
OR FABRIC SOFTENER AMOUNTS.
• When going from wash-to-dry automatically,
Always use a fabric softener (Or a Detergent
with built-in softeners) so clothes release from
the drum after the high speed spin.
• ONLY use Cotton Heavy Duty for heavy
cottons (towels, jeans, etc.)
• For items that may wrinkle, use Low Spin in
wash and Synthetics Dry
• To further prevent wrinkles, set a wash
ONLY cycle with LOW SPIN pressed. After the
wash cycle ends, remove large items (pants,
sheets, etc.) from the drum and shake them
out. Loosely fold them and place them back in
the drum. Then set a Synthetics Dry cycle with
LOW HEAT pressed.
• For mixed DRY CYCLE loads, remove items
that may wrinkle while still damp (dress shirts,
etc.) Hand press and hang them. Then,
continue drying the rest (underwear, towels,
etc.)
• NEVER OVER DRY LAUNDRY. Over drying is a
major cause of wrinkling. A certain amount of
humidity is what makes fabrics soft and fluffy.
WARNING!
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that have
been washed with flammable or chemical
solvents (e.g. trichlorethylene).
18 Washing and drying
This appliance can only be used to dry clothes
that have been pre-washed in water.
Do not use the appliance to dry foam rubber or
similar materials
Combo laundry FAQ’s
Is using a combination washer-dryer much
dierent than what I’m use to?
Yes, in some ways. You are washing and drying
in the same drum and load sizes are smaller.
Wash cycles are similar, but because combination washer-dryers are compact and operate
using 115V (vs. 230V), dry times are longer.
Instead of washing several, bulky loads of
laundry in one day, you’ll learn to adjust your
laundry habits to launder smaller, more convenient loads every day or two.
Why do I need to load my drum less full for ‘dry’
and ‘wash-to-dry’ cycles?
Your machine can wash larger loads than it can
dry. Remember, separate washers and dryers
have drums of dierent sizes (the dryer drum is
usually 2 times bigger), and your machine
washes and dries in the same drum. When you
program your machine to ‘dry’ or ‘wash-to-dry’
you must load the drum no more than 1/2 to
3/4 full. (NOTE: Automatic wash-to-dry not
available when Silk is selected)
What factors aect drying times?
Drying times depend largely on the type of
material (some bers absorb more water than
others), and the dampness of the articles when
drying is started (1200 RPM spin vs. 800- 600
RPM spin), and on the amount of laundry that is
being dried. Jeans, towels and similar (rather
thick) articles will take longer to dry.
Sample wash-to-dry loads
To get you started, here are a few sample load sizes that
can go directly from wash through dry. NOTE: Data
purely indicative. Actual drying times will vary depending on type/weight of material.
Sample Load 1
Wash Cycle: Regular Cotton Heavy Duty/ Dry Time:
90-120 minutes
2-3 Bath Towels (27 x 52 / all 100% cotton)
2 Hand Towels (16 x 28)
1-2 Wash Cloth(s) (13 x 13)
Sample Load 2
Wash Cycle: Regular Cotton Heavy Duty/ Dry Time:
70 to 120 min.
1 Flat Sheet (90 x 102 / all 230 thread count)
1 Fitted Sheet (60 x 80)
2 Standard Queen Pillowcases (21 x 32)
Sample Load 3
Wash Cycle: Regular Cotton Heavy Duty / Dry Time:
70 to 95 min.
1 Hand Towel (16 x 28)
1 Pair Jeans (35 waist/32 inseam)
1 Sweatshirt (Large, 50% cotton, 50% polyester)
Washing and drying 19
Care and maintenance
Turning off the water or
electricity supply
Turn off the water supply after every use.. This
will limit the wear of your appliances water
system and also prevent leaks. Unplug your
appliance when cleaning it, while on vacation
and during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance
can be cleaned with a soft cloth soaked in
lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the dispenser
Checking the water inlet
hoses
Check the water inlet hoses at least once a year.
Clean the filters and the water valves. If you see
any cracks, bulges or wear, replace hoses
immediately; During the wash cycles, water
pressure is very strong and a cracked hose could
easily split open.
WARNING! Never use inlet hoses that have
already been used.
IMPORTANT: Replace the inlet hoses at least
every ve years of use to reduce the risk of hose
failure. When replacing the inlet hoses, mark the
date of replacement on the label with a permanent marker.
drawer
Remove the dispenser by raising it and pulling it
out. Wash it under running water; repeat as
needed.
Caring for your appliance
door and drum
When not in use, leave the appliance door ajar
to prevent unpleasant odors from forming.
20 Care and maintenance
Cleaning the pump
PORTAN
T
T
T
B
efore c
leaning, make s
ure the wash
g
.
No lint filter to clean
pre-chamber
The washer-dryer is fitted with a self-cleaning
pump that does not require regular maintenance.
However, if small items (such as coins or buttons)
fall into the pre-chamber that protects the pump,
you will need to retrieve them.
cyc
le ha
s ended and unplu
the appliance
Your Splendide removes the lint automatically with
the help of it’s self-cleaning pump, so there’s no lint
filter to clean.
To access the pre-chamber:To access the pre-chamber:
To access the pre-chamber:
To access the pre-chamber:To access the pre-chamber:
1 Using a screwdriver, remove the cover panel on
the lower front of the washer-dryer.
2 Place a small dish or tray below the cover.
Unscrew the pre-chamber by rotating it counter
clockwise. A little water may trickle out. This is
perfectly normal.
3 Clean the interior thoroughly.
4 Screw the pre-chamber back on.
5 Reposition the panel, making sure the tabs are
positioned correctly before you push the panel
back onto the appliance.
Care and maintenanceCare and maintenance
Care and maintenance
Care and maintenance 2Care and maintenance
11
11
Troubleshooting
Before calling for assistance, make sure the problem cant easily be solved by consulting the following list
Problem Possible Causes / Solution
• There is no power.
• The appliance is not plugged into a socket, or not enough to make contact.
• There has been a power failure.
The washer-dryer
won’t start.
The washer-dryer
does not ll with
water.
• The appliance door is not shut properly.
• The STA
• The water tap is not turned on or supply hoses are kinked.
• The water inlet hose is not connected to the tap.
• The hose is kinked.
• The water tap is not turned ON.
• The water pressure is insucient.
• The START button has not been pressed.
RT button has not been pressed. (Note: It should be held a minimum of one
second.)
The washer-dryer
continuously lls
and empties with
water.
The washer-dryer
does not drain or
spin.
The washer-dryer
vibrates too much
during the spin
cycle.
The washer-dryer
leaks.
• The drain hose is too low or too far into the standpipe.
• The wall drainage system doesn’t have an air break.
• Some programs have a slower nal spin to take best care of the fabrics (See ‘Cycle
Description Chart’, pg. 14).
• The drain hose is kinked.
• Check the pump pre-chamber (See ‘Cleaning the pump pre-chamber,’ pg. 18)
• Remove the drain hose from the standpipe or under-sink trap and check for blockages, ensuring that the water can drain freely away from the machine.
• The Transit Screws are still in place. Remove the screws (See ‘Removing the transit
screws’, pg. 6).
• Verify the washer is resting on a solid, level surface.
• The drum is overloaded.
• The washer-dryer is not level (See ‘Levelling the washer-dryer’, pg. 8).
• The washer-dryer is too close to cabinets or adjacent walls.
• The water inlet hose is not screwed on correctly (See ‘Connecting the water inlets’,
pg. 6).
• The washer is not level.
• The drain pump or drain hose is obstructed.
• The detergent dispenser is obstructed (See ‘Cleaning the dispenser drawer’, pg. 18).
• The drain hose is not secured properly. (See ‘Connecting the drain hose’, pg. 7).
FAULT CODES:
The DOOR LOCK LED
ashes rapidly at the
same time as at least
one other LED
22 Troub leshooting
The unit has entered diagnostic mode and there may be a problem.
1. Unplug the unit, or turn o the circuit breaker to the unit for a minimum of 40
seconds.
2. Plug the unit back in, and switch the machine back ON.
3. If the unit still enters the diagnostic mode, please record which lights are ashing,
as well as the model and serial number of your machine.
4. Call Splendide Technical Support.
Loading...