Splash Lab TSL.R.030 Series, TSL.R.030.C.E120, TSL.R.030.CP.E120, TSL.R.030.BK.E120, TSL.R.030.BR.E120 Installation And Maintenance Manual

TSL.R.030

ribbon hand dryer

installation + maintenance

contents

3 Safety and Warnings

4 Box Contents

5 Technical Data

6 Before You Install

8 How to Install

14 Commissioning

16 Operation

16 Maintenance

17 Cleaning

18 Troubleshooting

21 Diagram

22 Spare Parts / Accessories

23 Warranty

Back Cover Contact Details

2 TSL. R.030 RIB BON HA ND DRYER MANUAL

TSL.R.030 ribbon hand dryer

Read and save these instructions

WARNING

To reduce the risk of fire, electric shock or injury to persons, observe the following:

+ Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer (see back page for details)

+ This equipment should be installed in a way that ensures all electrical parts are

kept dry.

+ A means of electrical isolation must be incorporated in the fixed wiring, in

accordance with the current local regulations in force.

+ Disconnect the power supply before performing any maintenance on the product

+ Children should not play with this equipment. Cleaning and maintenance shall not

be performed by children without supervision.

+ This equipment is designed to be used in commercial and public areas; it is not

intended for domestic or residential use.

+ Replace fuse only with the same type and rating of fuse.

+ Ensure wiring and cover is installed correctly before connecting to live power

supply.

+ If in doubt, consult an electrician.

+ This product is not intended for use in a domestic or residential application.

+ The dryer must be installed in accordance with the electrical installation

regulations in force at the time of installation.

+ The hand dryer must be earthed.

!

General information

[phone]
5450 W 83rd St, Los Angeles CA90045
500 7th Ave, New York NY10018

Technical support

[e-mail]

For further contact information visit:

www.thesplashlab.com

Original instructions

TSL. R.030 RIB BON HA ND DRYER MANUAL 3

box contents

A

B

C

K

J

H

D

E

F

G

A Dryer head assembly

B Hand dryer motor unit

C Power cable

D Anti-rotation collar (already installed)

E Gasket

F Anti-rotation washer

G Fixing nut

H Motor mounting screws

I Hex wrench

J Air hose

4 TSL. R.030 RIB BON HA ND DRYER MANUAL

technical data

Finishes TSL.R.030.C.E120 Bright Polished Stainless steel

TSL.R.030.CS.E120 Brushed Stainless steel
TSL.R.030.CP.E120 Brushed Copper
TSL.R.030.BK.E120 Brushed Black
TSL.R.030.BR.E120 Brushed Brass
TSL.R.030.BZ.E120 Brushed Bronze

Voltage 110 - 120V ac; 60Hz

Current 7.6 - 8.4A

Power consumption 0.84 - 1.0kW

Standby power 0.3 - 0.4kW

Drying time <15 seconds

Weight 17lb 13oz

Material AISI 304 stainless steel

Noise levels 70.6dB

Heating element 500W

Motor type Brush type; dual ball bearings

Motor power 500 - 350W

Air speed 36 7 ft/s

Air flow 25.3 cu ft/min

Sensor range 5” +/-1 ”

Security cut-off time 30 seconds

Motor thermal protection Auto resetting thermostat set at 275°F

Heater thermal protection Auto resetting thermostat set at 185°F

Thermal cutout fuse set to 288°F

Insulation Class 1

IP rating IP35

Approvals CE, UL, RoHS

Warranty 1 year parts and labour; additional 4 years parts

only (Motor brushes excluded as these are a
wearing part, and dependant on usage)

TSL. R.030 RIB BON HA ND DRYER MANUAL 5

before you install

Location

Ribbon hand dryers are supplied with 18”
of flexible hose, so the dryer motor unit
must be fitted within 18” of the head unit,
to ensure that the motor air-outlet head
can be connected

Basins

Use of a The Splash Lab Monolith basin
is recommended for use with the Ribbon
range of products.

If an alternative basin is used, then
appropriate mounting points must
be created in basin or countertop to
accommodate the Ribbon products.

Ø

1 3/8"

Power supply

A 15A fused supply must be provided for
connection to the mains power supply.

Disclaimer: Circuits should only use
80% of their given amperage to prevent
overloads. The standard US 120V 15 Amp
circuit should only use up to 12 of its 15
amps.

Spacing

If the Ribbon hand dryer is installed with
other units from the Ribbon range, these
should be fitted at 5 1/2” centres.

5 1/2" 5 1/2"

3"

6 TSL. R.030 RIB BON HA ND DRYER MANUAL

before you install

FRONT SIDE

Default
Sensor

2-1/8"

Range
3/4"-5-1/8"

7-5/16"

6"

1-5/16"

Ø

THROUGH HOLE

Ø

1-1/4"

2-11/16"

10-3/4"

12-1/16"

5-7/8"

5-5/8"

3/8" MIN

1-3/8" MAX

4-3/8"

11-3/4" - 12-9/16"7-9/16"

Mains

Power Supply

TSL. R.030 RIB BON HA ND DRYER MANUAL 7

how to install

1

Drill hole 1 3/8” diameter in counter-top, if
not already cut.

8 TSL. R.030 RIB BON HA ND DRYER MANUAL

2

Fit anti-rotation washer from below basin