Splash On Tap Installation Manual

NOTICE: THE METHANOL BARREL MUST BE GROUNDED

NOTICE: A back-flow preventer in compliance with local
and/or state requirements must be installed on the water
line to bring the unit to safety standards.

8. (6) Tank bracket bolts

9. (6) Tank bracket washers

10. (4) 3/8” Lead anchors

11. (4) 3/8” Anchor screws

12. (4) Anchor washers

13. (1) Methanol hose

14. (2) Hose clamps

15. (1) Bung wrench

SPLASH On Tap™

Installation Guide

40 Gallon Water Driven Proportioner (#40-SOTWD)

P a g e | 1

Congratulations on your recent purchase of the SPLASH On Tap proportioner, the future of windshield
washer fluid. If you ever find that you need a replacement part you will be pleased to know that all

parts are available at reasonable prices.

This package contains the following (DOES NOT INCLUDE A BACK-FLOW PREVENTER):

1. (1) 40-SOTWD Proportioner

2. (1) Windshield washer fluid hydrometer

3. (1) Magnetic snap action float

4. (1) Poly Float with chain

5. (4) Magnetic snap action float mounting screws

6. (1) Methanol quick connect

7. (1) Concentrate screen

8. (1) Metal wall bracket

www.SPLASHwash.com Questions? [phone]

P a g e | 2

NOTICE: THE METHANOL BARREL MUST BE GROUNDED

NOTICE: A back-flow preventer in compliance with local
and/or state requirements must be installed on the water
line to bring the unit to safety standards.

COMPLIANCE WITH LAW

The Equipment is designed to dispense windshield washer fluid containing methanol, which is a
volatile organic compound (VOC). The United States Environmental Protection Agency (EPA) regulates
the use of VOCs and specifically limits the amount of methanol that can be used in products.

The Equipment must be used in compliance with federal, state, and local laws and regulations. The
EPA has regulated that under no circumstances shall there be more than 35% methanol by weight in
the final product. Please see the following website for more details:

http://www.gpo.gov/fdsys/pkg/FR-1998-09-11/pdf/98-22660.pdf. The concentrate provided by the

manufacturer and distributor must be diluted to comply with federal, state, and local VOC regulations.
For example, California, Arizona, Georgia, Texas and Oregon all have state and/or local laws that
further regulate the amount of methanol that can be in products. Other states may have such laws as
well. The customer is responsible for ensuring that he or she properly dilutes the methanol
concentrate to be in compliance with all federal, state, local laws and regulations.

Although the manufacturer has attempted to ensure that its equipment complies with all federal, state
and local laws and regulations, neither the manufacturer nor the distributor can be responsible for nor
guarantee that the customer will use the equipment in accordance with all laws and regulations.
Therefore, customer agrees that neither the manufacturer nor the distributor shall be held responsible
or liable for the use of this equipment in violation of federal, state and local laws and regulations. In
addition, customer acknowledges and agrees equipment must be properly installed according to federal,
state and local laws and regulations, to include a back-flow preventer on the water line. It is customer’s
the responsibility to comply with federal, state and local laws and regulations pertaining to proper use
and installation of the equipment.

www.SPLASHwash.com Questions? [phone]

40-SOTWD Set-Up Instructions

Step 1: Finding a location for the proportioner

 Locate an area for tank installation, if possible near the air pump for the overhead reels and

water line.

 Unit must be hung on a concrete wall.

P a g e | 3

Step 2: Installing the unit on the wall

 At the final location of the unit measure and mark a level line 50” from the floor.
 Detach metal wall bracket from the back of the unit.
 Place the bottom of the metal bracket level with the line and mark the four mounting holes.
 Re-attach metal bracket to the proportioner using all six bolts, making sure they are all snug.
 Using a hammer drill, drill the four pre-marked holes with a 5/8” bit.
 Install the four 3/8” lead anchors into the holes.
 Hang unit on the wall using the four predrilled anchors. Secure with the supplied washers and

screws.

www.SPLASHwash.com Questions? [phone]