Spl CHARISMA User Manual

Model 9733
Manual
Dual Channel Tube Processor
SOUND PERFORMANCE LAB
by Hermann Gier and Paul White Version 1.2 – 1/1999
The information in this document has been carefully verified and is assumed to be correct. However Sound Performance Laboratory (SPL) reserves the right to modify the product described in this manual at any time. Changes without notice. This document is the property of SPL and may not be copied or reproduced in any manner, in part or full without the autho­rization of SPL.
Limitations of Liability: In no event will SPL be liable for any damages, including loss of data, lost profits, cost of cover or other special, incidental, consequential or indirect damages arising from the use of the unit, however caused and on any theory of liabi­lity. This limitation will apply even if SPL or an authorized dealer has been advised of the possibility of such damage.
SPL electronics GmbH
P.O. Box 12 27
D- 41368 Niederkruechten, Germany
Phone: +49 - 21 63 / 9 83 40
Fax: +49 - 21 63 / 98 34 20
eMail: info@spl-electronics.com
www.spl-electronics.com
©
1999 SPL electronics GmbH. All Rights Reserved.
CHARISMA
Model 9733
Manual
3
Contents
Foreword................................................................................ 3
Thanks ................................................................................... 3
Introduction........................................................................... 4
Operation safety.................................................................... 4
Connections........................................................................... 5
Control Elements
DRIVE.......................................................................... 6
MAX/PROCESS LED´s................................................... 6
CHARISMA.................................................................... 7
OUTPUT....................................................................... 7
BYPASS........................................................................ 7
Applications.......................................................................... 7
Normal Processing................................................................ 8
Set-up positions....................................................... 8
Getting started.......................................................... 8
The CHARISMA control................................................ 8
Tip offs...................................................................... 9
Extreme Processing.............................................................. 9
Tip offs...................................................................... 9
Power Supply.........................................................................10
Specifications.........................................................................11
Warranty................................................................................12
Dear customer,
Thank you for the confidence you have shown towards SPL
electronics GmbH by purchasing the SPL C
HARISMA. You have
decided to use a tool of high performance which sets you in the position to have faster success and a better sound quality in your music productions. As a typical SPL unit the C
HARISMA
combines exemplary specifications and high manufacturing standard with excellent sound quality to provide you a precious component for studio purposes.
Please read this manual carefully to ensure you have all the
information you need to use the C
HARISMA.
We wish you every success with your new C
HARISMA.
Your S
OUND PERFORMANCE LAB-Team
I would like to start with my thanks to all our staff, who created what is to be described here. The importance of their exceptional qualification and talents cannot be overestimated.
A very special “thank you” goes to Manfred Reckmeyer, whose longterm experience in tube technology including custom modifications of tube gear for many artists made this product possible.
Our products are often tested and compared in many publica­tions and by our customers themselfs and constantly valued with best results. I would like to pass on this broad appreciation to those, who deserve it – my excellent colleagues.
Hermann Gier
Foreword
Thanks
4
CHARISMA is a 2-channel tube processor designed to improve the power, punch, dynamics and the subjective loudness of the signal being processed.
Designed to introduce a subjective tonal warmth and a smooth bottom end into digitally recorded material, C
HARISMA
is a joint development between SPL and Manfred Reckmeyer, the designer responsible for the development of the 8-channel C
HARISMA.
C
HARISMA represents a solution that far exceeds the mere
simulation of tape saturation, and C
HARISMA´s tube saturation
characteristics can be fully controlled by the user. The concept of operation is simple. Each C
HARISMA channel has three potentio-
meters: D
RIVE sets the drive level to the tubes, CHARISMA adjusts
the tube saturation characteristic, and O
UTPUT sets the output
signal level.
C
HARISMA also helps to prevent overload and clipping on digi-
tally or analogue recorded tracks. You should use C
HARISMA
while recording before your digital recorder in order to clip­protect your recording (e. g. limiting peaks from live-recorded drums or reducing sharp “esses” from vocals). C
HARISMA gives
your signals more clarity, transparency and presence. Each part of the mix, instrument or vocal can easier be distinguished and located. Using C
HARISMA on single instruments alone lets those
signals stick out of the mix. C
HARISMA also helps you to place
vocals in a densed playback and maintaining their presence.
We will start with general safety hints, followed by the connections on the rear panel. We then take a look at the controls on the front and go on with practicals tips for the usage of C
HARISMA.
The housing of C
HARISMA has the standard 19"-EIA format and
occupies 1U (44 mm) in your rack. When installing the unit in a 19"-rack, the rear side of the unit needs some support, especi­ally in a touring case.
C
HARISMA should not be installed near units which produce
strong magnetic fields or extreme heat. Do not install C
HARISMA
directly above or below power amplifiers or digital processors. This eliminates problems which could result from interfering high-frequencies such as clock frequencies, MIDI or SMPTE control signals.
Check that the voltage details quoted on the back panel are the same as your local mains electricity supply. Use a minus (-) screwdriver to set the voltage selector to the voltage for the area in which the unit will be used.
Never cover up the ventilation slots on the top of the unit. If, during operation, the sound is interrupted or indicators no longer illuminate, or if abnormal odor or smoke is detected, or if liquids are spilled on the unit, immediately disconnect the power cord plug and contact your dealer.
Only clean your C
HARISMA with a soft, lint-free cloth. Use only
standard cleaning agents. Never use alcohol or paint thinner, because they may damage the finish.
Introduction
Operation safety
5
Before connecting CHARISMA switch the power off at all
connected units.
C
HARISMA is fitted with both XLR-connectors and TRS stereo
jacks for balanced operation, though the jacks may be used with unbalanced connections simply by plugging in mono jack-plugs. The level difference that normally occurs when a balanced input or output is used unbalanced is automatically compen­sated for.
Should the need arise to use the XLR connectors in an unba­lanced system, pin 3 of the XLRs should be grounded. Inserting a mono jack also unbalances the XLRs:
Both output stages operate in parallel, so it is possible to connect two different destination units simultaneously, for example to record to two different media at the same time or split the output between a mixer and effects processor. However, only one type of input (jack or XLR) should be connected at a time – the C
HARISMA is not intended to be used
as a mixer!
To ensure optimal signal quality, SPL has developed a new hybrid-component balanced input/output stage using all laser­trimmed resistors with a tolerance of 0.01%. This approach has resulted in an exceptionally high CCMR (common mode rejec­tion); 100dB at 1kHz and 80dB at 10 kHz. As a precaution, before connecting the C
HARISMA switch off the power to the unit
and to all connected units.
Other rear panel connections and switches:
- Voltage selector: 220-240V/50Hz or 100-120V/60Hz
- CSA/UL approved 3-pole power plug
- GND-Lift switch
Included in the packaging are:
- 3-wire, U-ground, power cord
- Owner´s Manual
- Warranty card
- SPL catalogue
Connections
1
2
3
Pin wiring: XLR connectors
1=GND 2=Hot(+) 3=Cold(-)
Pin wiring: stereo-jack plug
Tip=Hot(+) Ring=Cold(-) Sleeve=GND
6
Setting the drive level to the tubes
P
ROCESS = processing starts
M
AX = max. saturation
Examples:
– with snare or kick drum you can use heavy distortion (MAX LED illuminates)
– with layer sounds you should be very careful! Only use very little distortion if any (PROCESS LED rarely)
Control elements
The DRIVE control sets the drive level to the tubes. DRIVE values
can be adjusted between -oo dB and +24 dB.
You have control over the tube´s onset of saturation to find the
optimum point of processing. The higher the D
RIVE, the more tube
harmonics are being generated. At the same time, limiting gets stronger, increasing the density of the tube distortion.
Start off with the D
RIVE set at 0dB. Now the input level is
equivalent to the level driving the tube electronics. When you increase the value, you will get a more intense tube processing and the output volume rises. To compensate this use the O
UTPUT
control (4).
The P
ROCESS LED illuminates when CHARISMA starts its tube
processing. The tubes are starting to generate their typical sound and harmonical structure.
The M
AX LED indicates that the processing has reached its
maximum position. Now the tube is fully saturated and the typical limiting effect occurs. Increasing the D
RIVE results in more
tube distortion.
IMPORTANT: When you start to process a sound with heavy transients and attack, like a snare or a kick drum, you can drive the tubes into heavy saturation before you start to hear the tube´s distortion. When the P
ROCESS LED starts to illuminate you
hardly hear a change. Drive the tubes into heavier distortion so that the M
AX LED illuminates frequently and the tube processing
becomes audible.
On the other hand, when you process layer sounds or almost sinewave-like sounds you will sometimes hear the tube´s distor­tion even before the P
ROCESS LED illuminates. The C
HARISMA effect
is sometimes unpleasant on layer sounds! So, set the DRIVE level depending on the character of the sound you want to process. Our hearing detects overtones on sinewave-like signal immediately as unpleasant distortion, whereas squarewave-like sounds can be heavily distrorted and still remain pleasing to the ear.
Note: Do not set the D
RIVE controls to identical scale settings
and expect the tubes to act identical when different source characteristics are present at the inputs. Trust your hearing.
Drive
2
1
Max/Process LEDs
1
3
2
4
5
7
Selecting the sound character of the tube proces­sing
Monitor the peak level to set the OUTPUT level correctly!
Output
3
Charisma
4
Bypass
5
CHARISMA can be used everywhere, where audio signals might
benefit from the excellent tube sound. The C
HARISMA concept is
ideal for use in conjunction with digital multitrack or hard-disk recorder systems, but it can equally be used with analogue tape or DASH machines.
Making use of the typical tube harmonics and saturation sounds, as well as the natural tube limiting effect, while recor­ding, is of benefit to almost any signal – indeed there´s almost no limit to the applications. The sonic implications can best be characterized as gaining more presence, punch, and warmth.
In the MIDI studio, C
HARISMA is ideal for processing single
tracks such as keyboard or sampler sounds as well as vocals. In this application, the C
HARISMA is inserted into the mixer´s chan-
nels inserts or directly between the source and the desk.
The most flexible way to use C
HARISMA in the studio is to wire it
Applications
This unique control varies the tube sound and allows you to create varying sound characteristics from S
OFT to HARD.
Creating different tube sounds results in varying harmonical structures and adjustments in the S
OFT control range bring in
the harmonical distortion and the tube limiting very slowly (you can compare this with the soft-knee characteristic of a limiter). In comparison to the H
ARD control range the SOFT effect starts
off at relatively low levels. The sound becomes smooth and warm, is a little softer, and contains more harmonic distortion than the H
ARD sound.
In the H
ARD control range CHARISMA operates comparable to
the hard-knee characteristic of a limiter. The processing starts with full effect at one point whereupon the signal is sharply limited, and at this point, the sound becomes punchy and crispy.
Depending on the selected characteristic and intensities, a readjustment of the D
RIVE control may further emphasize the
desired effect.
The O
UTPUT control sets each channel´s output gain to
compensate for the level increase when the D
RIVE control has
added level to drive the tube circuitry.
Use a peak meter to set the O
UTPUT level correctly. If you
insert the C
HARISMA on your console or patchbay without having
control over the peak level you will end up with less peak level although the loudness is the same. This is because of the limiting effect of the tubes. C
HARISMA is designed to increase
loudness by maintaining the same peak level and to improve bit resolution on digital recording systems.
The bypass switch switches each C
HARISMA channel in and out
of processing (hard-bypass), and the bypass switch is labelled according to channel number.
8
into the patchbay. That way you can decide, whether it should be used while recording or later during mixdown – or simply inserted into specific channels. Processing subgroups is another interesting application. Using C
HARISMA while recording to
digital is the most beneficial application as the tube limiting prevents clipping.
Creating effects like tape saturation, Increasing loudness, Improving presence.
You control the sound of C
HARISMA with the DRIVE and
C
HARISMA controls. The OUTPUT control is used to compensate for
the level increase when the D
RIVE control is set higher than 0dB.
Set the D
RIVE to zero and CHARISMA to center position.
Set the O
UTPUT control fully clockwise (0dB).
Input and output levels should be identical now. Check this by
depressing the bypass switch, labeled with the channel number.
Turn the D
RIVE control slowly clockwise. You start to drive the
tube into saturation. The level increases. Compensate this by turning the O
UTPUT control counter clockwise.
The P
ROCESS LED illuminates when the processing starts.
Depending on the source characteristic you will hear the C
HARISMA process much more intense with sinewave-like/layer
sounds. When processing these sounds the P
ROCESS LED should
illuminate rarely. When processing squarewave-like/transient sounds you can drive the tubes harder. The P
ROCESS LED may
illuminate constantly and the M
AX LED may also light up
frequently. The M
AX LED tells you that the maximum satura-
tion of the tube is reached.
Now, check the peak level meters on your playing and recor-
ding unit and set the O
UTPUT controls in a way that identical
levels are shown on both units. Switching on C
HARISMA´s chan-
nels will give the aural impression that the processed signal is louder than the unprocessed. If this effect is not impressive enough, turn the D
RIVE control a little further clockwise.
After setting the D
RIVE control, start to vary the CHARISMA
control. This control varies the tube sound from HARD to SOFT.
In the S
OFT position the processing curve looks similar to that
of a soft-knee limiter curve. The tube processing comes in softly with a gently rounded curve, whereas in the H
ARD position the
programme material is treated more dramatic. This can be compared with the processing curve of a hard-knee limiter.
A specific C
HARISMA control setting may make it necessary to
readjust the D
RIVE control. If you use a SOFT setting, the proces-
The Charisma-
control
Getting started
Set-up positions
Normal processing
9
Avoiding clipping when recording digital.
Capturing the sound of analogue for digitally recorded drums.
Controlling the kick of the bass drum and the ounch of the snare.
Improving drum room sound.
Making acoustic guitars and electronics basses stand out in busy mix.
Giving extra charisma to vocals. Improving intelligibi­lity.
Making a tube mic out of your standard mic.
Creating heavily distorted ´in your face´ sounds.
Tip offs
sing starts earlier, which means you can hear the effect already at lower D
RIVE levels in comparison to HARD settings. A medium
D
RIVE level may already be sufficient to drive the tubes hard
enough.
In a H
ARD setting you will find yourself using higher DRIVE
levels, because the processing starts later than in a SOFT setting, but it is very efficient immediately.
When recording to a digital media it is essential to avoid clip­ping and the tube limiting is a great tool for this purpose. Critical peaks are smoothed resulting in increased subjective loudness while controlling the electrical level.
Traditionally, drums have been recorded to analogue tape – even digital drum tracks are frequently copied to analogue tape purely to capture the sound of tape saturation. With C
HARISMA,
you can achieve the same analogue warmth, punch and power without the inconvenience or noise of an analogue tape machine. Even sampled drums really start to sound much more like real drums.
Choose an extreme H
ARD setting (fully clockwise) for kick
drums or snares. You effectively prevent clips on your digital recorder while you also have control about the kick of the bass drum or the ounch of the snare. It is interesting to use C
HARISMA
on room tracks when recording live drums. Choose a SOFT setting with a high DRIVE level. This will open up your drum room.
Acoustic guitars benefit from the C
HARISMA effect with
improved transparency and clarity, yet the recorded instrument retains the same liveliness and character as the original. Electronic basses become better focused, or you can add just a hint of deliberate distortion to help make them stand out in a busy mix.
When recording vocals, the C
HARISMA allows the voice to stand
out in the mix without increasing the actual level – any good studio mic effectively becomes a valve mic. Intelligibility is greatly enhanced by the tube harmonics, and you can even make a clean voice sound smoky by driving the C
HARISMA a little harder.
That´s something a tube mic doesn´t allow you to do.
It is often a good trick to use a compressor before the C
HARISMA when processing vocals. This will help you finding an
appropriate D
RIVE level.
Producers of dancefloor/trance/ambient music will find C
HARISMA a remarkable creative tool for distorting bass drums,
snare- and lead sounds absolutely free from noise and hum – a clear advantage over the guitar-preamps. Even original 303/808 bass and drum sounds gain additional kick and authority. C
HARISMA lets you produce really ´in your face´
sounds.
10
Power Supply
Creating rough sounds, Creating new harmonics, Processing synth sounds.
C
HARISMA can be used with extreme settings: For example, set
the D
RIVE maximum and create richest Hammond organ sound.
Give clean guitars more bite or even softly distort them, or make vocals rough and dirty.
You can run your favorite samples and synth sounds through
C
HARISMA and give them the final edge. Give yor TB 303 clone
the bite of the original 303. By widening the harmonical spec­trum you have unlimited possibilities to boost and refreshen synth sounds or create new ones.
Special care has gone into the design of the power supply of
the C
HARISMA. The power supply is the heart of an electronic
system: The better it is, the better the whole system works and –in an audio system– the better it sounds.
This power supply is based around a custom made 15VA toroidal transformer and is designed to minimize induced hum and noise due to the non existence of an air-gap.
The primary voltage may be selected between 230V/50 Hz and 115 V/60 Hz by means of a recessed slide switch on the rear panel.
The rear panel ground-lift switch may be used where ground loops are causing hum problems. When the G
ND LIFT switch is
set to off, the circuit ground is no longer connected to the chassis ground. The power cord connector is a 3-wire, U-ground, stan­dard IEC mains connector for a detachable power cord (enclosed). Transformer, power cord and mains connector have VDE, UL and CSA approvals. The fuse has a value of 315 mA.
On the secondary side of the power supply, an RC combina­tion is used to filter out noise and hum voltages from the mains side. Both half-waves are smoothed with 2200 µF capacitors in the positive and negative voltage path. Both pathes use preci­sion voltage regulators, as deviations of only a few millivolts can result in audible changes such as a diffuse sound pattern.
Extreme Processing
Tip offs
11
Input & output stages
Instrumentation amplifier, electronically balanced (differential) transformerless Jack type TRS XLR type NC3 Nominal input level +6dB Input impedance = 220 kOhms Output impedance < 600 Ohms Max. input level +24dBu Reference level variable (Drive) Minimum load ohms 600 Ohms Hard bypass switch yes
Measurements
Frequency Response 30 Hz - 40 kHz
(40 kHz = -3 dB)
CCMR -100 dBu @100 Hz (common mode rejection) -100 dBu @1kHz
- 80dBu @ 10kHz
- 70dBu @ 20 kHz
THD & N 0,41% @1 kHz
(total harmonic distortion & noise) K2 max. 35%
S/N CCIR 468-2 -89dBu
Power Supply
Toroidal transformer 15 VA Fuse 315 mA Ground lift switch yes Voltage selector yes
Dimensions
Housing Standard EIA 19"/1U
482 x 44 x 237mm
Weight 3,4 kg
Subject to change without notice.
Specifications
12
SPL electronics GmbH (hereafter called SPL) products are warranted only in the country where purchased, through the authorized SPL distributor in that country, against defects in material or workmanship. The specific period of this limited warranty shall be that which is described to the original retail purchaser by the authorized SPL dealer or distributor at the time of purchase.
SPL does not, however, warrant its products against any and all defects:
1) arising out of materials or workmanship not provided or furnished by SPL, or 2) resulting from abnormal use of the product or use in violation of instructions, or 3) in products repaired or serviced by other than authorized SPL repair facilities, or 4) in products with removed or defaced serial numbers, or 5) in components or parts or products expressly warranted by another manufacturer.
SPL agrees, through the applicable authorized distributor, to repair or replace defects covered by this limited warranty with parts or products of original or improved design, at its option in each respect, if the defective product is shipped prior to the end of the warranty period to the designated authorized SPL warranty repair facility in the country where purchased, or to the SPL factory in Germany, in the original packaging or a replacement supplied by SPL, with all trans­portation costs and full insurance paid each way by the purchaser or owner.
All remedies and the measure of damages are limited to the above services. It is possible that economic loss or injury to person or property may result from the failure of the product; however, even if SPL has been advised of this possibility, this limited warranty does not cover any such consequential or incidental damages. Some states or coun­tries do not allow the limitations or exclusion of incidental or consequential damages, so the above limitation may not apply to you.
Any and all warranties, express or implied, arising by law, course of dealing, course of performance, usage of trade, or otherwise, including but not limited to implied warranties of merchantability and fitness for particular, are limited to a period of 1 (one) year from either the date of manufacture. Some states or countries do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state, country to country.
SPL electronics GmbH 41372 Niederkrüchten Germany
Warranty
Loading...