Spirit CE800ENT User Manual

&( (17ġ

2:1(5§60$18$/

Please carefully read this entire manual before operating yourġnew elliptical



ġ

( O O L S W L F D O 

ġġ

įġ

s

Table of Content

Important Safety Instructions………………………………………………………….….……2

Important Operation Instructions……………………………………………………….….…..3

Assembly Instructions………………………………………………………………….….……6

Features…………………………………………………………………………………………10

Operation of Your Elliptical…………………………………………………………………….11

Exploded View Diagram and Parts List………………………………………………..……..31

Thank you for purchasing our product, please save these instructions.
Please do not perform or attempt any customizing, adjustments, repair
or maintenance that is not described in this manual.

Elliptical

1

Thank you for purchasing our product, please save these instructions. Please do not
perform or attempt any customizing, adjustments, repair or maintenance that is not
described in this manual, if you experience any difficulty, please contact our website.

NOTE:

Article number: CE800 ENT
Use: Studio use
Max. user’s weight.:150 kg

WARNING

: The equipment shell be installed on a stable

base and properly leveled.

Dyaco International Inc.

Head Office:12F, No.111,Songjiang Road, Taipei 104,Taiwan

Tel:[phone] Fax:[phone]

Factory: No 1, Gong 1

Hemei Town, Changhua County 508, Taiwan

Tel:[phone] Fax:[phone]

ST

Road, Cyuan Sing Industrial Park

Elliptical

2

Important Safety Instructions

WARNING
DANGER -

outlet prior to cleaning and/or service work.

WARNING

elliptical on a flat level surface with access to a 120-volt,15-amp grounded outlet with only the
elliptical plugged into the circuit.

DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER. WITH ONLY ONE OUTLET
ON THE END.

 Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet

and elliptical may result.

 Keep children away from the elliptical. There are obvious pinch points and other caution

areas that can cause harm.

 Keep hands away from all moving parts.
 Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working

properly, call your dealer.

 Keep the cord away from heated surfaces.
 Do not operate where aerosol spray products are being used or where oxygen is being

administered. Sparks from the motor may ignite a highly gaseous environment.

 Never drop or insert any object into any openings.
 Do not use outdoors.
 To disconnect, turn all controls to the off position and then remove the plug from the outlet.
 Do not attempt to use your elliptical for any purpose other than for the purpose it is

intended.

 The hand pulse sensors are not medical devices. Various factors, including the user’s

movement, may affect the accuracy of heart rate readings. The pulse sensors are intended
only as exercise aids in determining heart rate trends in general.

 Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use

on your elliptical. Quality athletic shoes are recommended to avoid leg fatigue.

CAUTION:

To assure continued FCC compliance:

1. Any changes or modifications not expressly approved by the grantee of this device could
void the user's authority to operate the equipment.

- Read all instructions before using this appliance.

To reduce the risk of electric shock disconnect your elliptical from the electrical

- To reduce the risk of burns, fire, electric shock, or injury to persons, install the

2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.

3. Keep children under the age of 13 away from this machine.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Elliptical

3

MODEL: WB001

This device complies with Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator and your body.

Cet appareil radio est conforme au CNR d’Industrie Canada. L’utilisation de ce dispositif

est autorisée seulement aux deux conditions suivantes :

(1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à

accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de

compromettre le fonctionnement du dispositif.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour

un environnement non contrôlé.

Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la

source de rayonnement et votre corps.

Elliptical

4

IMPORTANT ELECTRICAL INSTRUCTIONS

WARNING

NEVER remove any cover without first disconnecting AC power.

If voltage varies by ten percent (10%) or more, the performance of your elliptical may be
affected. Such conditions are not covered under your warranty. If you suspect the voltage
is low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this elliptical to rain or moisture. This product is NOT designed for use
out-doors, near a pool or spa, or in any other high humidity environment. The operating
temperature specification is 40 to 120 degrees Fahrenheit, and humidity is 95%
non-condensing (no water drops forming on surfaces).

!

Important Operation Instructions

Ɣ

NEVER operate this elliptical without reading and completely understanding the results of anyġ
operational change you request from the computer.

• Understand that changes in resistance do not occur immediately. Set your desired resistance
level on the computerġconsole and release the adjustment key. The computer will obey the
command gradually.

• NEVER use your elliptical during an electrical storm. Surges may occur in your household power
supply that could damage elliptical components. Unplug the elliptical during an electrical storm as
a precaution.

• Use caution while participating in other activities while pedaling on your elliptical; such as

watchingġtelevision, reading, etc. These distractions may cause you to lose balance which may
result in serious injury.

• Do not use excessive pressure on console control keys. They are precision set to function

properly with littleġfinger pressure.

• Always hold on to a handle bar while making control changes.

•

Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure. If you feel the buttons are not functioning properly with normal
pressure contact your dealer.

Elliptical

5

Grounding Instructions

This product must be grounded. If the elliptical’s electrical system should malfunction or
breakdown grounding provides a path of least resistance for electric current, reducing the risk of
electric shock. This product is equipped with a cord having an equipment-grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.

DANGER

a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the
plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be
used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly grounded outlet, (shown
below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the like,
extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal
screw.

- Improper connection of the equipment-grounding conductor can result in

Elliptical

6

Assembly Pack Check List

Step1

#97 - M5 x 12mm
Phillips Head Screw (4 pcs)

#128 - 3/8” x 3-3/4”
Button Head Socket Bolt (6 pcs)

Step2

#130- 3/8” X19
Flat Washer (4 pcs)

#127 - 3/8” x 2-1/4”
Button Head Socket Bolt (4 pcs)

#129 - 3/8” X23
Curved Washer (6 pcs)

#97 - M5 x 12mm
Phillips Head Screw (4 pcs)

#126 - 5/16" × UNC18 × 15L
Socket Head Cap Bolt (2 pcs)

Elliptical

#106 - 5/16”
Flat Washer (2 pcs)

#131 - M5 x 10mm
Phillips Head Screw (8 pcs)

7

#119 – M6 x 15mm
Phillips Head Screw (2 pcs)

Step3

#132 - M8 x 25mm
Socket Cap Bolt (4 pcs)

#133 - 25mm
Wave Washer (2 pcs)

Step4

#137 - M10 x 12mm
Shoulder Bolt (2 pcs)

#135 - 3/8” x 3/4”
Hex Head Bolt
W / Loctite (2 pcs)

#138 - 3/8”
Flat Washer (2 pcs)

#107 - 5/16"
Flat Washer (1 pcs)

#136 - M10
Nylon Nut (2 pcs

#134 - 3.5mm x 12mm
Sheet Metal Screw (4 pcs)

)

#134 - 3.5 x 12mm
Sheet Metal Screw (14 pcs)

#97- M5 x 12mm
Phillips Head Screw (16 pcs)

Elliptical

8

Assembly Instructions

STEP 1 : RAIL ASSEMBLY

1. Gather HARDWARE FOR STEP 1.

2. Slide the RAIL ASSEMBLY (2) under the rear oval stabilizer tube of the main frame. Secure

together with 2 BOLTS (127) and 2 WASHERS (130) from the top of the tube and 4 BOLTS
(128) and 4 CURVED WASHERS (129) from the front of the tube. Make sure all 6 BOLTS are
tightened securely.

3. Install the CENTER ALUMINUM RAIL (89) with 2 BOLTS (127) and 2 CURVED
WASHERS (128) at the rear and 2 BOLTS (130) and 2WASHERS

(129) at the front.

4. Install the 2 TUBE STABILIZER COVERS (84 LEFT & 83 RIGHT) with 2 SCREWS (97)

to the middle STABILIZER TUBE and the 2 STABILIZER COVERS (83 left & 84 right) with
2 SCREWS (97) to the rear stabilizer tube.

Elliptical

9

STEP2 : PEDAL ARM ASSEMBLY

1. Gather HARDWARE FOR STEP 2.

2. Attach FOOTPLATES (L 49)to the pedal mounting plate with 4 SCREWS (131).

3. Slide the PEDAL ARM assembly (5) onto the crank axle of the main body. Be careful not to

force it because damage to the bearings can occur. Secure with a BOLT (126) and WASHER
(106).

4. Install the COVER (46) over the pedal arm connection at the rotation axle with a SCREW (119).

5. Install the ROLLER WHEEL COVER (50) with 2 SCREWS (97).

6. Repeat all steps with the oppostie PEDAL ARM assembly (6).

Elliptical

10

STEP 3: CONSOLE MAST AND SWING ARMS

1. Gather HARDWARE FOR STEP 3.

2. Unravel the COMPUTER CABLE (35), CSAFE CABLE(32),TV CABLE(33),NET CABLE (34),

CONSOLE POWER CABLE(36) ,HDMI (46)and snake it through the bottom of the CONSOLE
MAST (12) and out the top. To install mast tube (12), first insert three M8x25mm screws (132)

onto the mainframe then locate the mast tube (12) on its position and tighten three screws. Now
the last M8x25mm screw (132) must be with 5/16” flat washer (107) to tighten to the screw hole.

3. Mount the CONSOLE MAST COVERS (L 80) (R81) with 4 SCREWS (134).

4. Install 2 WAVE WASHERS (133) onto the CONSOLE MAST AXLE then install the

SWING ARMS (L11)(R10) onto the axles. Do not force them or use a hammer as damage to
the bearings can occur. Secure with a BOLT (135) and WASHER (138) on each arm.

5. Attach the bottom of the swing arms to the rod ends of the pedal arms using 2 SHOULDER

BOLTS (137) and 2 NYLON NUTS (136).

Elliptical

11