Page 1
Driveline Components Catalog
Center Yokes, Tube Yokes and
Ball Stud Tube Yokes
J300P-5
January 2016
Supersedes Section 5
Dated November 2012
Product pictured is intended to be a representation of product category.
Page 2
HOW TO USE THIS CATALOG
J300P-5
This publication contains data on Spicer center yokes and ball stud tube yokes for double cardan
driveshafts and Spicer tube yokes for single cardan driveshafts.
HOW TO IDENTIFY A CENTER YOKE USING THIS CATALOG
To identify any center yoke, three pieces of information are required:
1. Determine the Series
2. Determine the dimension between center of U-Joint to center of U-Joint
3. Determine the type of part (circular or rectangular)
Example: To nd a 1310 Series rectangular type, with a center to center dimension of 2.75, see the
following example:
1. Find the 1310 Series heading
2. Find the Center to Center dimension of 2.750
3. Find a type 1 (circular is type 2, rectangular is type 1)
Order Spicer Center Yoke Part Number 2-26-177
Be sure to read any notes that are provided.
Series and all pertinent series dimensions appear as shown in the sample below:
C
1
Center to Center
Swing Diameter Type Center Yoke
1310 SERIES E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X, 5-786X
2.688 3.875 2 2-26-477
2.688 3.875 2 2-26-497
2.688 3.875 2 2-26-507
2.750 3.875 1 2-26-177
3.000 3.875 1 2-26-257
2
3
Lube hole thru web
HOW TO IDENTIFY A TUBE YOKE USING THIS CATALOG
To identify any tube yoke, three pieces of information are required:
1. Determine Series
2. Determine the size and wall thickness of the tube it ts
3. Determine the dimension from center of joint to weld point
Example: To nd a 1330 Series with a 2.000 center to weld dimension, that ts a 2.750 OD tube with a
.065 wall thickness, see the following example:
1. Find the 1330 Series heading
2. Find the 2.750 Tubing Diameter and .065 wall thickness (2.750 x .065 - S=Seamless, W=Welded)
3. Find the 2.000 Center to Weld dimension
Be sure to read any notes that are provided. Order Spicer Tube Yoke Part Number 5004393
Series and all pertinent series dimensions appear as shown in the sample below:
For Use With
1
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1330 SERIES E-3.875 D-1.062 USE KIT 5-213X, 5-790X, 5-812X, 5-791X
2.000 X.120W 1.766 2.120 2-28-2777
2.500 X.083W 2.344 1.719 2-28-1707
2
2.500 X.083W 2.344 2.537 2-28-3347•
2.750 X.065S 2.625 2.000 5004393
2.750 X.065W 2.625 2.540 5002395
2.750 X.083S 2.594 2.030 2-28-3937
2
Important: See Safety Information in General Information Section (J300P-GI)
3
Page 3
J300P-5
HOW TO USE THIS CATALOG
HOW TO IDENTIFY A BALL STUD TUBE YOKE USING THIS CATALOG
To identify any tube yoke, the following information is required:
1. Determine the Series
2. Determine the size and wall thickness of the tube it ts
3. Determine the dimension from center of joint to weld point
4. Determine the center of the joint to the end of the ball stud dimension
5. Determine the diameter of the ball stud
6. Determine the length of the ball stud
7. Determine the conguration and dimensions of the slinger or seal (if the part has a slinger or seal)
Example: To nd a 1310 Series ball stud tube yoke with a 1.440 center to weld dimension, that ts a
2.000 OD tube with a .120 wall thickness and a .594 diameter ball stud, see the following example:
1. Find the 1310 Series heading
2. Find the 2.000 Tubing Diameter and .120 wall thickness (2.000 x .120W)
3. Find the 1.440 Center to Weld dimension
4. Find the 1.641 Center to End of Ball Stud dimension
5. Find the .594 Ball Stud Length
6. Refer to the slinger and seal illustrations on page 13 to determine which seal/slinger conguration
you have.
If you have a seal, order Spicer ball stud tube yoke assembly part number 2-28-2867X
If you have a slinger, order Spicer ball stud tube yoke assembly part number 2-28-2947X
Be sure to read any notes that are provided.
Series and all pertinent series dimensions appear as shown in the sample below:
For Use With
Tube Butt Centerline Centerline L H Slinger/Seal Tube Yoke
Diameter Diameter to Point to End of
1
& Wall Thickness of Weld Ball Stud Part Number
F K J Ball Stud
Length Diameter
Ball Stud
Assembly
1310 SERIES E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X, 5-786X
1.250 X.120 W 1.016 1.500 1.641 .594 .500 231864 2-28-2997X
1.750 X.095 W 1.562 1.440 1.641 .594 .500 2-86-418 2-28-2827X
1.750 X.095 W 1.562 1.440 1.641 .594 .500 231864 2-28-2937X
2
2.000 X.120 W 1.766 1.440 1.641 .594 .500 2-86-418 2-28-2867X
2.000 X.120 W 1.766 1.440 1.641 .594 .500 231864 2-28-2947X
2.500 X.065 W 2.375 1.440 1.641 .594 .500 2-86-418 2-28-3087X
3
4
5
6
Footnotes for parts and assemblies that are discontinued, will be discontinued upon depletion of
stock, or not sold separately, are indicated by a symbol next to the part number. Match the symbol
to the appropriate status at the bottom of the page. All other footnotes are located immediately
below the yoke dimensional data.
IMPORTANT NOTICE: The data listed herein is correct to the best of our knowledge and belief;
having been compiled from reliable and ofcial sources of information. However, WE CANNOT
ASSUME ANY RESPONSIBILITY for possible error.
Important: See Safety Information in General Information Section (J300P-GI)
3
Page 4
CENTER YOKES
Snap Ring Design
Type 1 Type 2
J300P-5
C
Center to Center
Swing Diameter Type Center Yoke
1000 SERIES K-1.500 D-.938 USE KIT 5-170X, 5-170-1X
2.125 2.500 2 10-26-47
1210 SERIES E=2.688 D=1.062 USE KIT NO. 5-443X, 5-554X
2.688 3.375 2 2-26-457
1310 SERIES E=3.469 (UB,BS STYLE E=3.219) D=1.062, USE KIT 5-153X, 5-1310X
2.688 3.875 2 2-26-477
2.688 3.875 2 2-26-497
2.688 3.875 2 2-26-507
2.750 3.875 1 2-26-177
3.000 3.875 1 2-26-257
Lube hole thru web
1330 SERIES E=3.875 (UB,BS STYLE E=3.625) D=1.062 USE KIT 5-213X, 5-1330X
2.750 4.250 2 2-26-527
2.751 4.250 2 2-26-557•
2.766 4.250 2 2-26-467
1350 SERIES E=3.875 (UB,BS STYLE E=3.625) D=1.188 USE KIT 5-178X, 5-1350X
2.120 — 1 3-26-577•
2.750 4.250 1 3-26-317
2.875 4.682 2 3-26-757
1410 SERIES E=4.438 (UB,BS STYLE E=4.188) D=1.188 USE KIT 5-160X, 5-1410X
3.375 4.688 1 3-26-717
1480 SERIES E=4.438 (UB,BS STYLE E=4.188) D=1.375 USE KIT 5-188X,SPL55X
3.375 3.875 1 3-26-667
4.240 3.875 1 3-26-677
1550 SERIES E=5.250 (UB,BS STYLE E=4.964) D=1.375 USE KIT 5-155X, SPL70X
3.938 4.125 1 4-26-437•
1610 SERIES E=5.312 (HR STYLE E=5.312) D= 1.875 USE KIT 5-279X, 5-674X
4.576 — 1 5003513
1710 SERIES E=6.094 (HR STYLE=6.190) D=1.938 USE KIT NO. 5-280X, 5-675X
4.606 — 1 6-26-637M
• Part is discontinued Part is available until supply is exhausted © Not sold separately
4
Important: See Safety Information in General Information Section (J300P-GI)
Page 5
J300P-5
TUBE YOKES
Spicer Life Series™
Half Round
Design
For Use With Butt C-line to Yoke & Yoke Tube Yoke
Tube Diameter & Wall Diameter Point of Weld Design Assembly Part Number
F H
Used in Tube
Spring Tab
Design
Snap Ring
Design
SPL55 SERIES E=4.438 (UB,BS STYLE E=4.188) D=1.375 USE KIT SPL55X, SPL55-1X
USE STRAP ASSY 3-70-38X
3.500 X.083 W 3.334 2.834 HR 55-28-27
SPL70 SERIES E=5.250 (HR STYLE E=4.965) D=1.375 USE KIT 5-155X, SPL70X
USE STRAP ASSY 3-70-38X
3.500 X.095 W 3.321 2.875 HR 70-28-27
SPL90 SERIES E=5.375 (HR STYLE E=4.958) D=1.625 USE KIT NO. SPL100-1X
4.000 X.095 W 3.812 2.969 SR 90-28-17
4.000 X.134 W 3.743 2.969 SR 90-28-27
90-28-17 was replaced by 100-28-17
SPL100 SERIES E=5.375 (HR STYLE E=4.957) D=1.625 USE KIT NO. SPL100-1X
4.000 X.095 W 3.810 2.969 SR 100-28-17
4.000 X.095 W 3.810 3.240 HR 100-28-27
For HR style use strap kit part no. 90-70-18X
SPL140 SERIES E=5.028 (HR STYLE E=5.457) D=1.938 USE KIT SPL140X
USE SPRING TAB KIT NO. 211941X
4.331 X.197 W 3.957 3.504 ST 140-28-17
4.560 X.165 W 4.245 3.504 ST 140-28-27•
Also ts 4.213 x .138 wall tube
SPL170 SERIES E=6.026 (HR STYLE E=6.456) D=2.166 USE KIT SPL170-4X, SPL170-SF4X
USE SPRING TAB KIT NO. 211941X
— 4.112 4.567 ST 170-28-13415
— 4.112 4.567 ST 5013415
5013415 was replaced by 170-28-13415; Tube yoke presses into splined sleeve
— 4.350 4.724 ST 170-28-37
4.500 X.134 W 4.242 4.567 ST 170-28-09269
4.500 X.134 W 4.242 4.567 ST 5009269
4.724 X.197 W 4.350 4.724 ST 170-28-27
4.961 X.118 W 4.746 3.700 ST 170-28-17
Tube yoke presses into splined sleeve
Tube yoke presses into splined sleeve
5009269 was replaced by 170-28-09269
SPL250 SERIES E=5.986 (HR STYLE E=6.417) D=2.362 USE KIT SPL250-3X, SPL250-SF3X
USE SPRING TAB KIT NO. 211941X
— 4.423 4.882 ST 250-28-37
5.197 X.236 W 4.746 4.094 ST 250-28-17
Tube yoke presses into splined sleeve
• Part is discontinued Part is available until supply is exhausted © Not sold separately
5 Important: See Safety Information in General Information Section (J300P-GI)
Page 6
TUBE YOKES
J300P-5
Outside (OSR)Inside (ISR)
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1000 SERIES K-1.500 D-.938 USE KIT 5-170X, 5-170-1X
1.250 X.095 W 1.068 2.560 10-26-37
1.750 X.065 W 1.625 2.000 10-27-1 10-28-17
1.750 X.065 W 1.631 2.000 10-28-97
10-28-17 was replaced by 10-28-97
1100 SERIES E=2.656 D=.938 USE KIT 5-101X OR 5-111X
1.250 X.095 W 1.068 1.688 1-26-297
2.000 X.065 W 1.881 1.500 1-28-107•
1210 SERIES E=2.688 D=1.062 USE KIT NO. 5-443X, 5-554X
1.500 X.120 W 1.267 1.625 2-28-3027•
2.000 X.083 W 1.845 1.500 2-28-2417
2.500 X.065 W 2.381 1.312 2-28-1947
1310 SERIES E=3.469 (UB,BS E=3.219) D=1.062, USE KIT 5-153X,5-1310X,5-1310-1X
1.250 X.095 W 1.068 2.125 2-26-187
1.250 X.120 S 1.016 2.125 2-26-347
1.250 X.188 S .886 2.281 2-26-147
1.750 X.065 W 1.630 1.688 2-28-447
1.750 X.095 W 1.571 1.688 2-28-3187
2.000 X.065 W 1.881 1.688 2-28-417
2.000 X.083 W 1.845 1.688 2-27-7 2-28-357
2.000 X.095 W 1.821 1.688 2-28-577
2.000 X.120 W 1.771 1.688 2-28-1757
2.000 X.120 W 1.771 1.965 2-28-02324
2.000 X.120 W 1.771 1.965 5002324
2.250 X.095 W 2.062 2.000 2-28-547•
2.500 X.065 W 2.381 1.844 2-27-4 2-28-277
2.500 X.083 W 2.345 1.844 2-27-9 2-28-367
2.750 X.065 W 2.631 1.688 2-27-5 2-28-307
2.750 X.083 W 2.595 1.688 2-28-1617§
3.000 X.065 W 2.881 1.688 2-27-6 2-28-327
3.000 X.065 W 2.881 1.844 2-28-3207
3.000 X.083 W 2.845 1.688 2-27-24 2-28-437
3.250 X.065 W 3.130 1.688 2-28-557
3.500 X.065 W 3.381 1.688 2-27-10 2-28-397
3.500 X.083 W 3.345 1.688 2-27-12 2-28-427
4.000 X.083 W 3.844 1.500 2-28-477
4.000 X.083 W 3.845 1.906 2-28-3837§
5002324 was replaced by 2-28-02324
1330 SERIES E=3.875 (UB,BS E=3.625) D=1.062 USE KIT 5-213X,5-1330X,5-1330-1X
2.000 X.120 W 1.771 2.125 2-28-2777
2.500 X.083 W 2.345 1.719 2-28-1707
2.500 X.083 W 2.344 2.537 2-28-3347•
2.750 X.065 S 2.631 2.000 5004393•
• Part is discontinued Part is available until supply is exhausted © Not sold separately
6
Important: See Safety Information in General Information Section (J300P-GI)
Page 7
J300P-5
TUBE YOKES
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1330 SERIES (Cont'd) E=3.875 (UB,BS E=3.625) D=1.062 USE KIT 5-213X,5-1330X,5-1330-1X
2.750 X.065 W 2.625 2.540 5002395•
2.750 X.083 S 2.595 2.031 2-28-3937
2.750 X.083 W 2.591 2.539 2-28-4017
3.000 X.065 W 2.881 1.719 2-28-1177
3.000 X.083 W 2.845 1.719 2-28-1697
3.000 X.083 W 2.844 2.240 2-28-06030
3.000 X.083 W 2.844 2.240 5006030
3.500 X.065 W 3.381 1.812 2-28-1977
3.500 X.065 W 3.370 2.413 5002389•
3.500 X.083 W 2.345 1.812 2-28-1717
4.000 X.065 W 3.884 1.690 2-28-3787
4.000 X.065 W 3.884 2.220 2-28-12027
4.000 X.065 W 3.884 2.220 5012027
4.000 X.083 W 3.844 1.688 2-28-1967
5006030 was replaced by 2-28-06030
5012027 was replaced by 2-28-12027
1350 SERIES E=3.875 (UB,BS E=3.625) D=1.188 USE KIT 5-178X, 5-1350X, 5-1310-1X
2.000 X.120 W 1.771 2.125 3-28-777
2.500 X.083 W 2.345 1.938 3-27-1 3-28-47
2.750 X.065 W 2.631 2.031 3-28-1107•
3.000 X.065 W 2.881 2.030 3-28-137
3.000 X.083 W 2.845 2.000 3-27-2 3-28-57
3.000 X.083 W 2.844 2.031 3-28-1157
3.000 X.095 W 2.821 2.000 3-28-157
3.000 X.134 W 2.734 1.970 3-28-1137•
3.500 X.065 W 3.381 1.812 3-27-5 3-28-257
3.500 X.083 W 3.345 1.840 3-28-427
4.000 X.065 W 3.881 2.220 5006456
4.000 X.065 W 3.884 1.690 3-28-1667
4.000 X.065 W 3.881 2.220 3-28-06456©
4.000 X.083 W 3.844 1.688 3-28-417
3-28-1157 was replaced by 3-28-57
5006456 was replaced by 2-28-06456
1410 SERIES E=4.438 (UB,BS E=4.188) D=1.188 USE KIT 5-160X, 5-1410X,5-1410-1X
2.000 X.120 W 1.771 2.000 3-26-117
2.500 X.095 W 2.321 2.000 3-28-327
2.500 X.156 S 2.217 2.000 3-26-437
2.750 X.083 W 2.595 1.625 3-28-987
3.000 X.083 W 2.845 1.625 3-28-447
3.000 X.083 W 2.845 2.125 3-27-3 3-28-97
3.000 X.095 W 2.821 2.125 3-27-6 3-28-267
3.000 X.134 W 2.742 1.624 3-28-997•
3.000 X.250 W 2.500 1.625 3-28-1117•
3.500 X.065 W 3.381 2.125 3-27-8 3-28-367
3.500 X.083 W 3.345 2.125 3-27-4 3-28-557
3.500 X.095 W 3.321 2.125 3-28-857•
4.000 X.065 W 3.884 1.880 3-28-1267•
4.000 X.083 W 3.845 1.875 3-27-16 3-28-457
4.000 X.095 W 3.821 1.875 3-28-387
4.095 X.180 W 3.743 2.030 3-28-1087•
• Part is discontinued Part is available until supply is exhausted © Not sold separately
7 Important: See Safety Information in General Information Section (J300P-GI)
Page 8
TUBE YOKES
J300P-5
Bearing Plate StyleOutside (OSR)
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1480 SERIES E=4.438 (UB,BS E=4.188) D=1.375 USE KIT 5-188X, SPL55X, SPL55-1X
3.000 X.095 W 2.821 1.688 3-28-497
3.500 X.083 W 3.345 2.031 3-27-22 3-28-537
3.500 X.083 W 3.345 2.312 3-28-547
3.500 X.095 W 3.321 2.031 3-28-567
4.000 X.083 W 3.845 2.031 3-27-20 3-28-507
4.000 X.095 W 3.821 2.031 3-28-627
1550 SERIES E=5.250 (UB,BS E=4.964) D=1.375 USE KIT 5-155X, SPL70X, SPL70-1X
3.500 X.095 W 3.321 1.844 4-28-257
3.500 X.095 W 3.321 2.188 4-27-18 4-28-307
3.500 X.095 W 3.321 2.688 4-27-16 4-28-417
3.500 X.095 W 3.321 3.125 4-28-427•
3.500 X.134 W 3.243 1.810 4-28-627
3.500 X.134 W 3.243 2.188 4-28-487
3.500 X.156 W 3.199 2.188 4-28-657
4.000 X.083 W 3.845 2.188 4-28-277
4.000 X.095 W 3.812 2.188 4-28-297•
1610 SERIES E=5.312 (HR STYLE E=5.312) D= 1.875 USE KIT 5-279X, 5-674X
3.500 X.095 W 3.320 3.000 5-27-7 5-28-167
3.500 X.134 W 3.243 3.000 5-27-25 5-28-627
3.500 X.134 W 3.250 3.000 5-28-717•
3.500 X.134 W 3.243 3.810 5-28-887
3.500 X.156 W 3.199 3.000 5-27-9 5-28-207
3.500 X.156 W 3.263 3.000 5-28-957
3.550 X.207 W 3.141 2.220 5-28-837•
3.550 X.207 W 3.153 2.220 5-28-977M
Metric bolt holes; uses 5-585XM u-joint
3.550 X.207 W 3.141 3.000 5-28-967•
4.000 X.134 W 3.743 3.000 5-28-327
High angle yoke
1710 SERIES E=6.094 (HR STYLE=6.190) D=1.938 USE KIT NO. 5-280X, 5-675X
3.500 X.156 W 3.198 3.031 6-27-7 6-28-137
4.000 X.134 W 3.743 3.031 6-27-17 6-28-347
4.000 X.134 W 3.743 3.031 6-28-557M
4.000 X.134 W 3.743 3.688 6-28-467
4.000 X.134 W 3.743 4.060 6-28-527
4.500 X.134 W 4.242 3.031 6-28-407
High angle yoke
1760 SERIES E=7.000 (HR STYLE=7.094) D=1.938 USE KIT NO. 5-407X, 5-677X
4.095 X.180 W 3.743 3.031 6.3-28-17
1810 SERIES E=7.547 (HR STYLE=7.643) D=1.938 USE KIT NO. 5-281X, 5-676X
4.500 X.134 W 4.243 3.375 6.5-27-9 6.5-28-117
4.500 X.259 W 4.003 3.375 6.5-28-127
• Part is discontinued Part is available until supply is exhausted © Not sold separately
8
Important: See Safety Information in General Information Section (J300P-GI)
Page 9
J300P-5
TUBE YOKES
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1880 SERIES E=8.094 D=2.188 USE KIT 5-308X
4.500 X.259 W 4.003 4.000 8-28-147
1950 SERIES E=10.094 D=3.062 USE KIT 5-192X
6.000 X.500 S 5.125 6.531 9-26-18X•
5C SERIES P=4.531 S=1.685 KEYWAY-.562 USE KIT 5-5111X
2.500 X.159 W 2.186 2.224 5C-28-27•
.375-24 Threaded Holes
6C SERIES P=5.531 S=1.689 KEYWAY-.562 USE KIT 5-6111X
2.756 X.159 W 2.448 1.870 6C-28-27•
.375-24 Threaded Holes
• Part is discontinued Part is available until supply is exhausted © Not sold separately
9 Important: See Safety Information in General Information Section (J300P-GI)
Page 10
ALUMINUM TUBE YOKES
Outside
(OSR)
J300P-5
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1310 SERIES E=3.469 D=1.062 USE KIT 5-3613X
2.750 X.120 S 2.531 1.375 2-28-2787•
3.000 X.120 S 2.782 1.375 2-28-2427
3.250 X.083 S 3.104 1.969 2-28-3367•
3.750 X.083 S 3.604 2.130 2-28-3717•
4.000 X.083 S 3.855 2.125 2-28-3637•
4.000 X.083 S 3.853 2.130 2-28-3697•
1330 SERIES E=3.875 D=1.062 USE KIT 5-3614X
3.500 X.081 W 3.355 1.839 2-28-4047•
3.500 X.083 W 3.355 1.840 2-28-3767
3.500 X.120 S 3.280 1.837 2-28-2757•
4.000 X.083 S 3.855 2.125 2-28-3317
4.000 X.083 S 3.855 2.232 2-28-16881
4.000 X.083 S 3.855 2.232 2-28-16882
4.000 X.083 S 3.855 2.232 5016881
5016881 was replaced by 2-28-16881; w/vent hole thru web
4.000 X.083 S 3.855 2.232 5016882
5016882 will be replaced by 2-28-16882 when supply is exhausted
4.000 X.083 S 3.855 2.406 2-28-3327
4.000 X.083 S 3.855 3.130 2-28-3377
4.000 X.083 W 3.844 2.130 2-28-4057•
4.160 X.086 S 3.998 2.130 2-28-3687
4.160 X.086 S 3.998 2.406 2-28-3517
4.506 X.098 W 4.388 2.205 2-28-01588
4.506 X.098 W 4.388 2.205 5001588
4.520 X.075 S 4.388 2.130 2-28-3507
4.540 X.083 S 4.388 4.000 2-28-01484
4.540 X.083 S 4.388 4.000 5001484
5.000 X.065 S 4.888 1.820 2-28-3487
5.000 X.065 S 4.888 4.110 2-28-3527
Use plug no. 232639 in vent hole
w/vent hole thru web
Use plug no. 232639 in vent hole
5001484 was replaced by 2-28-01484
• Part is discontinued Part is available until supply is exhausted © Not sold separately
10
Important: See Safety Information in General Information Section (J300P-GI)
Page 11
J300P-5
ALUMINUM TUBE YOKES
For Use With
Tube Diameter & Wall Butt Diameter C-line to Point of Weld & Yoke Assembly Part Number
F H
Used in Tube Yoke Tube Yoke
1350 SERIES E=3.875 D=1.188 USE KIT 5-3615X
3.500 X.120 S 3.280 1.837 3-28-977
3.500 X.165 S 3.188 1.837 3-28-1197
4.000 X.083 S 3.855 2.125 3-28-1297
4.000 X.083 S 3.855 2.406 3-28-1307
4.160 X.086 S 3.998 2.130 3-28-1617
4.160 X.086 S 3.998 2.232 3-28-16885
4.160 X.086 S 3.998 2.232 5016885
4.160 X.086 S 3.998 2.410 3-28-1437•
4.500 X.065 S 4.388 4.000 3-28-10274
4.500 X.065 S 4.388 4.000 5010274
5010274 was replaced by 3-28-10274
4.500 X.095 S 4.325 3.173 5006297•
4.500 X.095 W 4.325 3.173 3-28-07154
OPTIONAL TUBE: 4.574 X .134
4.500 X.095 W 4.325 3.173 5007154
5007154 was replaced by 3-28-07154; w/vent hole thru web
4.520 X.075 S 4.388 2.130 3-28-1407
5.000 X.065 S 4.888 1.840 3-28-01701•
5.000 X.065 S 4.888 1.840 5001701•
5.000 X.065 S 4.888 1.844 3-28-1347
5.000 X.065 S 4.888 4.110 3-28-1447
5.090 X.107 S 4.876 3.173 3-28-06301
5.090 X.107 S 4.888 3.173 3-28-07058
5.090 X.107 S 4.888 3.173 3-28-12681
5.090 X.107 S 4.876 3.173 5006301
5006301 was replaced by 3-28-06301; w/vent hole thru web
5.090 X.107 S 4.888 3.173 5007058
5007058 was replaced by 3-28-07058
5.090 X.107 S 4.888 3.173 5012681
w/vent hole thru web
w/vent hole thru web
w/vent hole thru web
1410 SERIES E=4.438 D=1.188 USE KIT 5-3616X
4.000 X.083 S 3.853 2.290 3-28-1607•
4.000 X.083 W 3.855 2.130 3-28-03535
4.000 X.083 W 3.855 2.130 3-28-03536
4.000 X.083 W 3.855 2.130 5003535
4.000 X.083 W 3.855 2.130 5003536
4.000 X.103 S 3.812 2.125 3-28-1537•
4.157 X.087 S 3.998 2.290 3-28-1757
4.506 X.098 S 4.325 2.125 3-28-1387•
4.510 X.063 S 4.384 2.290 3-28-1547•
4.510 X.063 S 4.384 2.290 3-28-1597•
5.000 X.063 S 4.888 2.281 3-28-1647
5.000 X.065 S 4.888 4.109 3-28-1657
5003535 was replaced by 3-28-03535; Use plug no. 232639 in vent hole
5003536 was replaced by 3-28-03536
Use plug no. 232639 in vent hole
• Part is discontinued Part is available until supply is exhausted © Not sold separately
11 Important: See Safety Information in General Information Section (J300P-GI)
Page 12
BALL STUD TUBE YOKES
For Constant Velocity Applications
J300P-5
For Use With
Tube Butt Centerline Centerline L H Slinger Tube Yoke
Diameter Diameter to Point to End of
& Wall Thickness of Weld Ball Stud Part Number
F K J Ball Stud
Length Diameter
Ball Stud
Assembly
1210 SERIES E=2.688 D=1.062 USE KIT NO. 5-443X, 5-554X
2.500 X.065 W 2.375 1.310 1.641 .594 .500 231413 2-28-2407X
2.500 X.083 W 2.334 1.310 1.640 .594 .500 231413 2-28-3657X
1310 SERIES E=3.469 (UB,BS STYLE E=3.219) D=1.062, USE KIT 5-153X, 5-1310X
1.250 X.120 W 1.016 1.500 1.641 .594 .500 231864 2-28-2997X
1.750 X.095 W 1.562 1.440 1.641 .594 .500 231864 2-28-2937X
1.750 X.095 W 1.562 1.440 1.641 .594 .500 2-86-418 2-28-2827X
2.000 X.120 W 1.766 1.438 1.641 .594 .500 2-28-2857
2.000 X.120 W 1.766 1.440 1.641 .594 .500 231864 2-28-2947X
2.000 X.120 W 1.766 1.440 1.641 .594 .500 2-86-418 2-28-2867X
2.500 X.065 W 2.375 1.440 1.641 .594 .500 2-86-418 2-28-3087X
2.500 X.083 W 2.344 1.440 1.641 .594 .500 2-86-418 2-28-2887X
2.500 X.083 W 2.344 1.440 1.641 .594 .500 231864 2-28-2957X
2.750 X.065 W 2.625 1.281 1.641 .594 .500 231864 2-28-2987X
2.750 X.065 W 2.625 1.281 1.641 .594 .500 2-86-418 2-28-2747X
2.750 X.083 W 2.584 1.440 1.641 .594 .500 231864 2-28-3817X•
3.000 X.065 W 2.875 1.440 1.641 .594 .500 231864 2-28-2967X
3.000 X.065 W 2.875 1.440 1.641 .594 .500 2-86-418 2-28-2907X
3.000 X.083 W 2.844 1.440 1.641 .594 .500 2-86-418 2-28-2927X
3.000 X.083 W 2.844 1.440 1.641 .594 .500 231864 2-28-2977X
1330 SERIES E=3.875 (UB,BS STYLE E=3.625) D=1.062 USE KIT 5-213X, 5-1330X
2.000 X.120 W 1.766 1.375 1.670 .590 .500 2-86-418 2-28-3257X
2.000 X.120 W 1.766 1.375 1.670 .590 .500 231259 2-28-2157X
2.500 X.083 W 2.344 1.375 1.670 .590 .500 231259 2-28-2137X
2.500 X.083 W 2.344 1.375 1.670 .590 .500 2-86-418 2-28-3067X
2.500 X.095 W 2.312 1.375 1.670 .590 .500 2-86-418 2-28-3277X•
3.000 X.065 W 2.875 1.440 1.670 .422 .500 231259 2-28-2117X
3.000 X.083 W 2.844 1.375 1.670 .590 .500 2-86-418 2-28-3447X
3.000 X.083 W 2.844 1.440 1.670 .590 .500 231259 2-28-2187X
1350 SERIES E=3.875 (UB,BS STYLE E=3.625) D=1.188 USE KIT 5-178X, 5-1350X
2.750 X.083 W 2.611 1.440 1.732 .590 .500 2-86-418 3-28-1747X
3.000 X.083 W 2.844 1.440 1.732 .590 .500 2-86-418 3-28-1327X
3.000 X.083 W 2.844 1.551 1.732 .590 .500 3-28-09422X
3.000 X.083 W 2.844 1.551 1.732 .590 .500 5009422
5009422 was replaced by 3-28-09422X
3.500 X.083 W 3.344 1.440 1.732 .590 .500 2-86-418 3-28-1527X
OEM only
• Part is discontinued Part is available until supply is exhausted © Not sold separately
12
Important: See Safety Information in General Information Section (J300P-GI)
Page 13
J300P-5
SOCKET YOKE ASSEMBLY DIMENSIONS
Style 1 Style 2
Bolt Holes Dimensions Fits C/L
Flanged Socket Bolt Circle
Diameter to End Ball Stud
Yoke Assembly Series Style Diameter
A B C D E
211489X● 1210 1 3.500 2.468 2.468 0.484 2.000 1.625 0.500
211543X■◊ 1310 1 3.500 2.484 2.484 0.484 2.000 1.625 0.500
211229X■► 1310 1 3.500 2.484 2.484 0.484 2.000 1.625 0.500
212130X■ 1310 1* 3.750 2.712 2.712 0.401 2.750M 1.500 0.500
211198X● 1310 1 4.000 2.937 2.937 0.453 3.125 1.625 0.500
211452X● 1310 1 4.250 3.000 3.000 0.453 3.125 1.625 0.500
211545X■ 1310 1 4.250 3.000 3.000 0.453 3.125 1.625 0.500
212040X■ 1310 1 4.250 3.000 3.000 0.488 3.126 1.620 0.500
211631X■ 1330 1 4.250 3.000 3.000 M12X1.75th’d 2.000 1.625 0.500
211889X● 1330 2 4.000 2.953 2.656 0.453 3.125 1.875 0.500
211606X 1330 2 4.000 2.953 2.656 0.453 3.125 1.812 0.500
211520X● 1330 2 4.000 2.953 2.656 0.453 3.125 1.875 0.625
211868X● 1330 2 4.250 3.000 3.000 0.453 3.125 1.812 0.500
211913X■ 1330 1 4.250 3.000 3.000 0.462 3.125 1.625 0.500
212024X■ 1350 1 4.250 3.000 3.000 M12X1.75th’d 2.000 1.625 0.500
212025X■ 1350 1 4.250 3.000 3.000 M12X1.75th’d 2.680 1.625 0.500
** 5009419■ 1350 1 4.250 3.000 3.000 0.459 3.125 1.620 0.500
*Male Pilot
**2-12-229 spring not included
Size
Style 1
Bolt Holes Dimensions C/L
Flanged Socket Bolt Circle
to End Ball Stud
Yoke Assembly Series Style Diameter
A B C E
211342X 1210 3 2.437 1.500 2.343 .250-28th’d 1.531 0.500
211519X 1210 — 2.437 1.500 2.343 .250-28th’d 1.640 has .500 stud
211355X 1310 3 3.218 1.500 2.343 .312-24th’d 1.531 0.500
211544X■◊ 1310 3 3.218 1.500 2.343 .312-24th’d 1.656 0.500
211179X● 1330 3 3.625 1.500 2.875 .312-24th’d 1.562 0.500
210841X 1330 3 3.625 1.500 2.875 .312-24th’d 1.562 0.625
211996X■◊ 1330 3 3.625 1.500 2.875 .312-24th’d 1.690 0.500
212019X■ 1350 3 3.625 1.625 2.750 .312-24th’d 1.757 0.500
● Flush Zerk (#230977) ► Socket OD 1.394
■ Non-Greasable ◊ Socket OD 1.625
Size
13 Important: See Safety Information in General Information Section (J300P-GI) Important: See Safety Information in General Information Section (J300P-GI)
Page 14
SLINGERS AND SEALS
J300P-5
230962 231259
231413
14
231864
Important: See Safety Information in General Information Section (J300P-GI)
Seal
2-86-418
Page 15
J300P-5
PART NUMBER INDEX
1-26-297 ....................................6
1-28-107 ....................................6
2-26-147 ....................................6
2-26-177 ....................................4
2-26-187 ....................................6
2-26-257 ....................................4
2-26-347 ....................................6
2-26-457 ....................................4
2-26-467 ....................................4
2-26-477 ....................................4
2-26-497 ....................................4
2-26-507 ....................................4
2-26-527 ....................................4
2-26-557 ....................................4
2-28-277 ....................................6
2-28-307 ....................................6
2-28-327 ....................................6
2-28-357 ....................................6
2-28-367 ....................................6
2-28-397 ....................................6
2-28-417 ....................................6
2-28-427 ....................................6
2-28-437 ....................................6
2-28-447 ....................................6
2-28-477 ....................................6
2-28-547 ....................................6
2-28-557 ....................................6
2-28-577 ....................................6
2-28-1177 ................................... 7
2-28-01484 ..............................10
2-28-01588 ..............................10
2-28-1697 ..................................7
2-28-1707 ..................................6
2-28-1717 ..................................7
2-28-1757 ..................................6
2-28-1947 ..................................6
2-28-1967 ..................................7
2-28-1977 ..................................7
2-28-02324 ................................6
2-28-2417 ..................................6
2-28-2427 ................................10
2-28-2777 ..................................6
2-28-2857 ..............................12
2-28-3027 ..................................6
2-28-3187 ..................................6
2-28-3207 ..................................6
2-28-3317 ................................10
2-28-3327 ................................10
2-28-3377 ................................10
2-28-3487 ................................10
2-28-3507 ................................10
2-28-3517 ................................10
2-28-3527 ................................10
2-28-3687 ................................10
2-28-3767 ................................10
2-28-3787 ..................................7
2-28-3837 ..................................6
2-28-3937 ..................................7
2-28-4017 ..................................7
2-28-06030 ................................7
2-28-12027 ................................7
2-28-16881 ..............................10
2-28-16882 ..............................10
2-28-1617§ ................................6
2-28-2747X .............................12
2-28-2827X .............................12
2-28-2867X .............................12
2-28-2887X .............................12
2-28-2907X .............................12
2-28-2927X .............................12
2-28-3067X .............................12
2-28-3087X .............................12
2-28-3257X .............................12
2-28-3277X .............................12
2-28-3447X .............................12
3-26-117 ..................................... 7
3-26-317 ....................................4
3-26-437 ....................................7
3-26-577 ...................................4
3-26-667 ....................................4
3-26-677 ....................................4
3-26-717 ....................................4
3-26-757 ....................................4
3-28-47 ......................................7
3-28-57 ......................................7
3-28-97 ......................................7
3-28-137 ....................................7
3-28-157 ....................................7
3-28-257 ....................................7
3-28-267 ....................................7
3-28-327 ....................................7
3-28-367 ....................................7
3-28-387 ....................................7
3-28-417 ....................................7
3-28-427 ....................................7
3-28-447 ....................................7
3-28-457 ....................................7
3-28-497 ....................................8
3-28-507 ....................................8
3-28-537 ....................................8
3-28-547 ....................................8
3-28-557 ....................................7
3-28-567 ....................................8
3-28-627 ....................................8
3-28-777 ....................................7
3-28-857 ....................................7
3-28-977 ..................................11
3-28-987 ....................................7
3-28-997 ....................................7
3-28-1087 ..................................7
3-28-1107 ................................... 7
3-28-1117 ...................................7
3-28-1137 ................................... 7
3-28-1157 ................................... 7
3-28-1197 ................................. 11
3-28-1267 ..................................7
3-28-1297 ................................11
3-28-1307 ................................11
3-28-1347 ................................11
3-28-1387 ................................11
3-28-1407 ................................11
3-28-1437 ................................11
3-28-1447 ................................11
3-28-1537 ................................11
3-28-1547 ................................11
3-28-1597 ................................11
3-28-1607 ................................11
3-28-1617 ................................11
3-28-1647 ................................11
3-28-1657 ................................11
3-28-1667 ..................................7
3-28-01701 ..............................11
3-28-1757 ................................11
3-28-03535 ..............................11
3-28-03536 ..............................11
3-28-06301 ..............................11
3-28-06456 ................................7
3-28-07058 ..............................11
3-28-07154 ..............................11
3-28-10274 ..............................11
3-28-12681 .............................. 11
3-28-16885 ..............................11
3-28-09422X ............................12
3-28-1327X .............................12
3-28-1527X ..............................12
3-28-1747X .............................12
4-26-437 ....................................4
4-28-257 ....................................8
4-28-277 ....................................8
4-28-297 ....................................8
• Part is discontinued Part is available until supply is exhausted © Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
15 Important: See Safety Information in General Information Section (J300P-GI)
Page 16
PART NUMBER INDEX
J300P-5
4-28-307 ....................................8
4-28-417 ....................................8
4-28-427 ....................................8
4-28-487 ....................................8
4-28-627 ....................................8
4-28-657 ....................................8
5-28-167 ....................................8
5-28-207 ....................................8
5-28-327 ....................................8
5-28-627 ....................................8
5-28-717 ....................................8
5-28-837 ....................................8
5-28-887 ....................................8
5-28-957 ....................................8
5-28-967 ....................................8
5-28-977M .................................8
6-26-637M ................................4
6-28-137 ....................................8
6-28-347 ....................................8
6-28-407 ....................................8
6-28-467 ....................................8
6-28-527 ....................................8
6-28-557M .................................8
6.3-28-17 ...................................8
6.5-28-117 .................................. 8
6.5-28-127 .................................8
8-28-147 ....................................9
9-26-18X ....................................9
10-26-37 ....................................6
10-26-47 ....................................4
10-28-17 ....................................6
10-28-97 ....................................6
55-28-27 ....................................5
70-28-27 ....................................5
90-28-17 ....................................5
90-28-27 ....................................5
100-28-17 ..................................5
100-28-27 ..................................5
140-28-17 ..................................5
140-28-27 ..................................5
170-28-17 ..................................5
170-28-27 ..................................5
170-28-37 ..................................5
170-28-09269 ............................5
170-28-13415 ............................5
250-28-17 ..................................5
250-28-37 ..................................5
313073-10 ................................10
324030-10 ................................10
528566-6 ....................................6
535871-10 ................................10
634487-10 ................................10
656402-10 ................................10
663706-10 ................................10
784236-10 ................................10
787889-10 ................................10
2312592-28-2117X .................12
2312592-28-2137X .................12
2312592-28-2157X .................12
2312592-28-2187X .................12
2314132-28-2407X .................12
2314132-28-3657X .................12
2318642-28-2937X .................12
2318642-28-2947X .................12
2318642-28-2957X .................12
2318642-28-2967X .................12
2318642-28-2977X .................12
2318642-28-2987X .................12
2318642-28-2997X .................12
2318642-28-3817X .................12
5001484-10 ..............................10
5001588-10 ..............................10
5001701-11 .............................. 11
5002324-6 ..................................6
5002389-7 ..................................7
5002395-7 ..................................7
5003513-4 ..................................4
5003535-11 .............................. 11
5003536-11 .............................. 11
5004393-6 ..................................6
5006030-7 ..................................7
5006297-11 .............................. 11
5006301-11 .............................. 11
5006456-7 ..................................7
5007058-11 .............................. 11
5007154-11 .............................. 11
5009269-5 ..................................5
5009422-12 ..............................12
5010274-11 .............................. 11
5012027-7 ..................................7
5012681-11 .............................. 11
5013415-5 ..................................5
5016881-10 ..............................10
5016882-10 ..............................10
5016885-11 .............................. 11
5C-28-27 ....................................9
6C-28-27 ....................................9
• Part is discontinued Part is available until supply is exhausted © Not sold separately
16
Important: See Safety Information in General Information Section (J300P-GI)
Page 17
J300P-5
NOTES
17
Page 18
NOTES
J300P-5
18
Page 19
J300P-5
NOTES
19
Page 20
Dana Aftermarket Group
PO Box 1000
Maumee, Ohio 43537
Warehouse Distributors: 1.800.621.8084
OE Dealers: 1.877.777.5360
www.SpicerParts.com
J300P-5 Printed in U.S.A.
Copyright Dana Limited, 2016.
All rights reserved. Dana Limited.
Loading...