Page 1
Driveline Components Catalog
Slip Yoke Assemblies
J300P-3
July 2012
Supersedes Section 3
Dated August 2008
Driveshaft-style slip yokes, slip flanges, splined sleeves, and more,
plus slip yoke assemblies for transmission applications.
Product pictured is intended to be a representation of product category.
Page 2
J300P-3
How To Use This Catalog
INCLUDED IN THIS CATALOG
Driveshaft Style slip yokes - page 3, Slip Flange- page 13, Splined Sleeves - page 14, Hex, Square
and Round Hole- page 16, Transmission-type - page 17,
HOW TO IDENTIFY A PART USING THIS CATALOG
To identify any slip yoke, four pieces of information are required:
1. Determine Series
2. Determine spline O.D.
3. Determine number of teeth
4. Determine length - centerline to end/ face to end / end of spline to weld
5. Determine hub diameter (if a transmission-type slip yoke)
Series and all pertinent series dimensions appear as shown in the sample below:
1100 SERIES E-2.656 D-.938 USE KIT 5-101X & 5-111X
Spline O.D. and number of teeth are found at the beginning of each data section--
1.062-16 Spline
Individual part data is shown following the spline data heading--
2.875 .938 500174-1 D1A 1-68-14 - SR 1-3-88KX
Footnotes for parts and assemblies that are discontinued, will be discontinued or replaced upon
depletion of stock, or not sold separately, are indicated by a symbol next to the part number. Match
the symbol to the appropriate status at the bottom of the page. All other footnotes are located
immediately below the yoke dimensional data.
IMPORTANT NOTICE: The data listed herein is correct to the best of our knowledge and belief;
having been compiled from reliable and offi cial sources of information. However, WE CANNOT
ASSUME ANY RESPONSIBILITY for possible error.
2
Important: See Safety Information in General Information Section (J300P-GI)
Page 3
J300P-3
Slip Yoke Assemblies
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap & Slip Yoke Part Number Assembly
of Spline of Plug Fitting Washer Kit Plug Number Order Separately Style Part Number
SPL55 SERIES E-4.440 D-1.374 USE KIT 5-803X, 5-804X, SPL55-1X, SPL55-2X
1.587-23 Based On 24 Involute Spline
7.949 1.732 — — 500166-26 212094X SR 55-3-61X
9.122 1.732 — — 500166-26 212094X SR 55-3-81X
SPL70 SERIES E-5.250 D-1.375 USE KIT 5-808X, 5-809X, SPL70-1X, SPL70X
1.776-26 Based On 27 Involute Spline
8.480 1.890 — — 70-68-18X 212146X SR 70-3-21X
9.279 1.890 — — 70-68-18X 212146X SR 5009115
5009115 was replaced by 70-3-09115X; Rubber valve in plug
9.279 1.890 — — 70-68-18X 212146X SR 70-3-09115X
9.279 1.890 — — 70-68-38X 212146X SR 70-3-41X
SPL90 SERIES E-5.375 D-1.625 USE KIT SPL90X
1.939-30 Involute Spline
8.250 1.750 500174-1 90-86-18 5-68-164 — SR 90-3-41X
Mates with 90-40-21 and 90-53-21
10.100 1.797 500174-1 90-86-18 5-68-108X — SR 90-3-21X
SPL100 SERIES E-5.380 IN, (HR STYLE 4.958 IN.) D-1.625 USE KIT SPL100-1X
1.965-29 Based On 30 Involute Spline
9.681 1.783 — — 5-68-164 212146X SR 100-3-41X
1000 SERIES K-1.500 D-.938 USE KIT 5-170X
1.000-6 Spline
5.500 1.500 500174-1 — — — SR 10-3-131X
1.125-10 Spline
5.500 — 500174-1 — — — SR 10-3-81X
1.156-26 Involute Spline
5.500 1.531 500174-1 D2L 2-68-23 — SR 10-3-291KX
1.250-16 Spline
4.438 1.400 500174-1 D2A — — SR 10-3-121KX
5.500 1.562 500174-1 D2A 2-68-23 — SR 10-3-18KX
1.250-6 Spline
5.500 1.400 500174-1 — — — SR 10-3-51X
1100 SERIES E-2.656 D-.938 USE KIT 5-101X, 5-111X
1.062-16 Spline
2.875 .938 500174-1 D1A 1-68-14 — SR 1-3-88KX
4.312 .938 500174-1 D1A 1-68-14 — SR 1-3-18KX
Rubber valve in plug
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
Important: See Safety Information in General Information Section (J300P-GI)
3
Page 4
Slip Yoke Assemblies
J300P-3
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1210 SERIES E-2.688 D-1.062 USE KIT 5-443X
1.219-26 Based On 28 Involute Spline
5.062 1.250 — — 500166-20 — SR 2-3-8811X•
5.109 1.547 — — 500166-20 211513X SR 2-3-9991X
1.250-14 Based On 16 Spline
6.344 1.547 — 211256X 500166-20 211513X SR 2-3-10521X
6.375 1.250 — — 500166-20 211344X SR 2-3-8861X
1310 SERIES E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X
1.250-14 Based On 16 Spline
6.562 1.438 — — 500166-20 211344X SR 2-3-10661X
1.250-16 Spline
3.562 1.000 500174-1 D2B 2-68-23 — SR 2-3-3951KX
4.125 1.000 500174-1 D2B 2-68-23 — SR 2-3-258KX
4.688 1.000 500174-1 D2A 2-68-23 — SR 2-3-198KX
5.000 1.000 500174-1 D2A 2-68-23 — SR 2-3-1421KX
6.125 1.000 500174-1 D2F 2-68-23 — SR 2-3-1461KX
6.562 1.438 500174-1 D2K 2-68-23 — SR 2-3-4441KX
6.562 1.438 500174-1 211256X 2-68-23 — SR 2-3-8841KX
1.338-18 Based On 20 Involute Spline
6.724 1.417 — 211121X 500166-22 — SR 2-3-15101X
7.360 1.500 — — 500166-22 212094X SR 2-3-15941X
1.375-15 Based On 16 Spline
6.000 1.062 — — 500166-22 211916X SR 2-3-10411X
6.688 1.062 500174-1 211121X 2-68-143 — SR 2-3-7661KX
6.690 1.062 — — 2-68-28X — SR 2-3-10021X
6.724 1.417 — — 500166-22 211916X SR 2-3-12881X
6.812 1.250 — — 500166-22 211932X SR 2-3-11351X•
7.875 1.500 — — 500166-22 211916X SR 2-3-12421X
1.375-16 Spline
3.750 1.000 500174-1 D2C 3-68-23 — SR 2-3-178KX
4.188 1.000 500174-1 D2C 3-68-23 — SR 2-3-348KX
5.375 1.000 — — 2-68-28X — SR 2-3-9031X
5.375 1.000 500174-1 211121X 3-68-23 — SR 2-3-12301KX
5.375 1.000 500174-1 D2C 3-68-23 — SR 2-3-128KX
6.000 1.062 500174-1 D2C 2-68-143 — SR 2-3-4951KX
6.000 1.062 500174-1 211121X 2-68-143 — SR 2-3-7981KX
6.344 1.062 500174-1 D2C 2-68-143 — SR 2-3-4071KX
Use boot #40465, clamps #40540-1,-2; I.S. snap ring style
Relief valve in plug
500174-1 lube fi t. & D2M dustcap, ordr sep.; Rel vlv in plug
Use dust cap kit D3E for reverse slip applications
• Part is discontinued Part is available until supply is exhausted Not sold separately
4
Important: See Safety Information in General Information Section (J300P-GI)
Page 5
J300P-3
Slip Yoke Assemblies
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1310 SERIES (Continued) E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X
1.375-16 Spline (Continued)
6.471 — — — — — CV 2-3-7461X
6.750 .875 500174-1 D2M 3-68-23 — SR 2-3-1931KX
6.812 1.500 500174-1 211121X 2-68-143 — SR 2-3-8001KX
6.875 1.500 500174-1 — 3-68-23 — SR 2-3-5221X
7.875 1.500 500174-1 — 3-68-23 — SR 2-3-5821X
7.875 1.500 500174-1 211121X 2-68-143 — SR 2-3-8021KX
1.377-31 Based On Involute 32 Spline
6.750 .875 500174-1 211121X 2-68-143 — SR 2-3-10261KX
6.750 .875 — — 500166-22 211600X SR 2-3-10801X•
1.378-31 Based On 32 Involute Spline
6.620 1.531 500174-1 D2N 2-68-134 — SR 2-3-7171KX
6.812 1.500 500174-1 211411X 2-68-143 — SR 2-3-10641KX•
6.812 1.500 — — 2-68-63 211600X SR 2-3-9371X•
1.390-30 Based On 31 Involute Spline
5.062 1.438 500174-1 211121X 3-68-23 — SR 2-3-8311X
5.062 1.438 231330 2-86-298 500166-22 — SR 2-3-8481X
5.062 1.438 — — 500166-22 — SR 2-3-8741X
1.500-16 Spline
2.906 .656 500174-1 D3F 2-68-64 — SR 2-3-7691KX
6.875 1.531 500174-1 D3A 3-68-33 — SR 2-3-6061KX
1330 SERIES SR: E-3.875 OTHERS E-3.625, D-1.062 USE KIT 5-213X,5-790X,5-812X
1.284-29 Based On 30 Involute Spline
6.600 1.100 — — 500166-22 — SR 2-3-13221X
1.338-18 Based On 20 Involute Spline
6.640 1.000 — — 500166-22 212094X SR 2-3-16221X
6.724 1.102 — — 500166-22 211932X SR 2-3-15651X
1.338-19 Based On 20 Involute Spline
6.700 1.000 — — 500166-22 212094X SR 2-3-13831X
1.375-14 Based On 16 Spline
6.720 1.102 — — 500166-22 211932X SR 2-3-14331X
7.039 1.417 — — 500166-22 211932X SR 2-3-06028X
7.039 1.417 — — 500166-22 211932X SR 5006028
1.375-15 Based On 16 Spline
5.410 1.060 — — 500166-22 211916X SR 2-3-13571X•
6.000 1.000 — — 500166-23 211916X SR 2-3-8921X
6.620 1.000 — — 500166-22 211932X SR 2-3-11991X•
6.625 1.000 — 211121X 2-68-28X — SR 2-3-11491KX
6.625 1.000 — 211121X 500166-22 211932X SR 2-3-11991KX•
6.625 1.000 500174-1 211121X 3-68-23 — SR 2-3-7681KX
7.500 1.000 500174-1 211121X 3-68-23 211463X SR 2-3-8941KX•
500174-1 lube fi tting & D2M dust cap, order separately
Use dust cap kit D3E for reverse slip applications
Use dust cap kit D3E for reverse slip applications
Spec 4X4 axle yoke w/hole in plug
Spec 4X4 axle yoke w/lube fi tting in yoke
Use boot #40465, clamps #40540-1,-2; I.S. snap ring style
Used on driveshaft w/outboard slip
5006028 was replaced by 2-3-06028X
211121X dust cap & washer kit, order separately
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
5
Page 6
Slip Yoke Assemblies
J300P-3
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1330 SERIES (Con't) SR: E-3.875 OTHERS E-3.625, D-1.062 USE KIT 5-213X,5-790X,5-812X
1.375-16 Spline
6.000 1.000 500174-1 D3E 3-68-23 — SR 2-3-4681KX
6.000 1.000 500174-1 211121X 2-68-143 — SR 2-3-7961KX
7.500 1.000 500174-1 211121X 2-68-28X — SR 2-3-12031KX
7.500 1.000 — — 3-68-23 — SR 2-3-7481X•
D2M dust cap & washer kit, order separately
7.500 1.000 500174-1 211121X 3-68-23 — SR 2-3-8041KX
1.378-31 Based On 32 Involute Spline
6.000 1.000 500174-1 211121X 2-68-143 — SR 2-3-10571KX•
1.500-15 Based On 16 Spline
7.312 1.188 — — 3-68-33 — SR 2-3-10871X•
Used on driveshaft w/outboard slip
7.500 1.000 500174-1 211158X 3-68-33 — SR 2-3-8111KX•
1.500-16 Spline
8.182 — — — — — CV 211391X
Slip Yoke is a ball stud & sleeve assembly; 500174-1 lube fi tting & D3A dust cap, order separate
1350 SERIES E-3.875 D-1.188 USE KIT 5-178X OR 5-799X
1.375-15 Based On 16 Spline
6.810 1.190 500174-1 211121X 3-68-33 — SR 3-3-2701KX
1.375-16 Spline
5.250 1.188 500174-1 D3E 3-68-33 — SR 3-3-758KX
5.688 1.188 500174-1 D2C 3-68-33 — SR 3-3-1421KX
5.812 1.188 500174-1 D3G 3-68-33 — SR 3-3-1501KX
6.625 1.188 500174-1 D3G 3-68-33 — SR 3-3-2591KX
1.377-31 Based On 32 Involute Spline
6.625 1.188 500174-1 D3F 3-68-33 — SR 3-3-2471KX
1.390-30 Based On 31 Involute Spline
4.810 1.190 — — 500166-22 — SR 3-3-3001X
Use boot #40929 & clamps 40540-4 & 40540-3; order separately
5.240 1.190 — 211121X 3-68-23 — SR 3-3-2861X
1.463-21 Based On 22 Involute Spline
7.310 1.160 — — 500166-24 212094X SR 3-3-6381X
Slip yoke barrel is tapered.
7.312 1.190 — — 500166-24 212010X SR 3-3-6201X
7.312 1.190 — — 500166-24 212010X SR 3-3-6981X
1.500-14 Based On 16 Spline
7.312 1.188 — — 500166-24 212010X SR 3-3-4781X
7.312 1.188 — — 500166-24 211916X SR 3-3-5461X
1.500-15 Based On 16 Spline
6.938 1.188 — — 500166-24 212010X SR 3-3-4651X
7.310 1.188 500174-1 211158X 3-68-33 — SR 3-3-5921KX
7.312 1.188 500174-1 211158X 3-68-33 212010X SR 3-3-2801KX
• Part is discontinued Part is available until supply is exhausted Not sold separately
Relief valve in plug
6
Important: See Safety Information in General Information Section (J300P-GI)
Page 7
J300P-3
Slip Yoke Assemblies
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1350 SERIES (Continued) E-3.875 D-1.188 USE KIT 5-178X OR 5-799X
1.500-16 Spline
3.344 1.062 500174-1 D3A 3-68-104 — SR 3-3-2931KX•
3.688 1.188 500174-1 D3A 3-68-33 — SR 3-3-398KX
3.938 1.188 500174-1 D3A 3-68-33 — SR 3-3-388KX
4.938 1.188 500174-1 D3K 3-68-33 — SR 3-3-5181KX
5.812 1.312 500174-1 D3A 3-68-33 — SR 3-3-598KX
5.812 1.380 — — 3-68-33 — SR 3-3-2991X
6.719 1.188 500174-1 D3A 3-68-33 — SR 3-3-1561KX
7.312 1.188 500174-1 D3A 3-68-33 — SR 3-3-488KX
7.930 1.156 — — 3-68-33 212010X SR 3-3-3601X
8.000 1.188 500174-1 D3A 3-68-33 — SR 3-3-2681KX
1410 SERIES E-4.438 D-1.188 USE KIT 5-160X OR 5-801X
1.375-16 Spline
5.240 1.160 — D3G — — SR 3-3-4421X
5.250 1.156 500174-1 D3E 3-68-33 — SR 3-3-788KX
5.812 1.156 500174-1 D3G 3-68-33 — SR 3-3-1481KX
1.463-21 Based On 22 Involute Spline
7.280 1.160 — — 500166-24 212010X SR 3-3-6611X
7.280 1.160 — — 500166-24 212010X SR 3-3-6771X
7.280 1.160 — — 500166-24 211503X SR 3-3-6791X
7.310 1.160 — — 500166-24 212010X SR 3-3-08019X
7.310 1.160 — — 500166-24 212094X SR 3-3-6341X
7.310 1.160 — — 500166-24 212010X SR 5008019
7.311 1.161 — — 500166-24 212094X SR 3-3-6701X
1.500-14 Based On 16 Spline
7.281 1.156 — — 500166-24 212010X SR 3-3-4871X
7.281 1.156 — — 500166-24 212010X SR 3-3-5491X
8.562 1.340 — — 500166-24 212010X SR 3-3-6831X
1.500-15 Based On 16 Spline
7.281 1.156 500174-1 211158X 3-68-33 — SR 3-3-5411KX
7.812 1.344 500167-2 D3A 3-68-18X — SR 3-3-748KX
8.562 1.344 500174-1 D3F 3-68-63 — SR 3-3-768KX
1.500-16 Spline
3.906 1.156 — — 3-68-33 — SR 3-3-3381X
3.906 1.156 500174-1 D3A 3-68-33 — SR 3-3-468KX
4.344 1.156 — D3F 3-68-33 — SR 3-3-3311KX
500174-1 lube fi tting & D3A dust cap, order separate
One tooth removed for lube passage
500174-1 lube fi tting, order separate
Used on driveshaft w/outboard slip
w/5.300” OD dampener
5008019 was replaced by 3-3-08019X
Part has wide tooth and relief valve in welch plug.
Part has wide tooth, mates w/3-40-531
Use dust cap 211158X, order separate
4.410 1.160 — — 3-68-33 — SR 3-3-3461X
500174-1 lube fi tting & D2M dust cap, order separately
5.250 1.156 500174-1 D3K 3-68-33 — SR 3-3-2041KX
5.250 1.160 — — 3-68-334 — SR 3-3-3401X
500174-1 lube fi tting & D2M dust cap, order separately
6.500 1.156 500174-1 D3A 3-68-33 — SR 3-3-118KX
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
7
Page 8
Slip Yoke Assemblies
J300P-3
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1410 SERIES (Continued) E-4.438 D-1.188 USE KIT 5-160X OR 5-801X
1.500-16 Spline (Continued)
6.688 1.344 500174-1 D3B 3-68-33 — SR 3-3-798KX
7.812 1.344 500174-1 — 3-68-33 — SR 3-3-4551X•
7.812 1.344 500174-1 D3A 3-68-33 — SR 3-3-508KX
7.812 1.344 500174-1 211158X 3-68-33 — SR 3-3-5481KX
7.812 1.344 — — 3-68-18X — SR 3-3-838X
8.562 1.344 500174-1 D3J 3-68-113 — SR 3-3-1831KX
1.528-23 Involute Spline
6.810 1.312 — — 3-68-163 — SR 3-3-6641X•
1.562-16 Spline
6.812 1.312 500174-1 D3H 3-68-163 — SR 3-3-1701KX
1.564-22 Based On 24 Involute Spline
6.720 1.220 — — 500166-26 212007X SR 3-3-6041X•
1.587-23 Based On 24 Involute Spline
6.720 1.220 — — 500166-26 212007X SR 3-3-7001X
1.605-15 Involute Spline
5.750 1.344 500174-1 D4G 3-68-163 — SR 3-3-3871KX
1.654-20 Involute Spline
4.812 1.312 — — 3-68-183 — SR 3-3-3791X
1.750-16 Spline
3.250 1.188 500174-1 D4F 3-68-54 — SR 3-3-1511KX
1480 SERIES E-4.438 D-1.375 USE KIT 5-188X, 5-803X OR 5-804X
1.562-16 Spline
6.000 1.312 — — 3-68-163 — SR 3-3-5141X•
6.812 1.312 500174-1 D3J 3-68-163 — SR 3-3-1601KX
9.500 2.000 500174-1 D3H 3-68-163 — SR 3-3-1641KX
1.564-23 Based On 24 Involute Spline
6.810 1.312 — — 500166-26 212007X SR 3-3-6061X
1.587-23 Based On 24 Involute Spline
6.810 1.312 — — 500166-26 212007X SR 3-3-7021X
1.784-27 Involute Spline
3.719 1.109 — — 3-68-203 — SR 3-3-3121X
2.250-10 Spline
3.719 1.188 500174-1 D3D 3-68-93 — SR 3-3-1621KX
Use dust cap D3F, order separate; Use lube fi tting 500174-1; order separate
Use dust cap 211158X, order separate; 500174-1 lube fi tting, order separate
For splined dust cap, use D3J
OEM Only
Hub dia. not ground
Hub dia. not ground
• Part is discontinued Part is available until supply is exhausted Not sold separately
8
Important: See Safety Information in General Information Section (J300P-GI)
Page 9
J300P-3
Slip Yoke Assemblies
LD & MD Driveshaft Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
1550 SERIES E-5.250 D-1.375 USE KIT 5-155X, 5-808X OR 5-809X
1.750-16 Spline
5.375 1.375 500168-2 D4M 4-68-143 — SR 4-3-1751KX
6.875 1.375 500168-2 D4K 4-68-143 — SR 4-3-1241KX
7.562 2.062 500168-2 D4M 4-68-143 — SR 4-3-2121KX
8.125 1.375 500168-2 D4J 4-68-143 — SR 4-3-1411KX
9.063 2.062 500168-2 D4M 4-68-143 — SR 4-3-2141KX
10.062 2.062 500168-2 D4J 4-68-143 — SR 4-3-1431KX
2.000-16 Spline
4.875 1.469 500168-2 5-86-68 4-68-43 — SR 4-3-1921KX
8.812 2.730 500167-2 5-86-68 5-68-78X — SR 4-3-2041KX
2.500-16 Spline
3.500 1.125 500168-2 D4L 4-68-74 — SR 4-3-1261KX
4.303 1.402 500168-2 D4L 4-68-74 — SR 4-3-08843KX
4.303 1.402 — — 4-68-74 — SR 5008843
5008843 was replaced by 4-3-08843KX; D4L dust cap kit- order separately
Relief valve in plug
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
9
Page 10
Slip Yoke Assemblies
J300P-3
HD Driveshaft Style
J F Part of Slip Yoke Assembly
Slip Yoke
C/L to C/L to Lube Dust Cap Slip Yoke Assembly
End of Face of Fitting & Washer Plug Style Part
Spline Plug Kit Number Number
1610 SERIES E-5.312 D-1.875 USE KIT 5-279X OR 5-674X
2.000-16 Spline
5.406 2.688 — — 5-68-154 BP 5-3-2911X
6.750 2.688 — — 5-68-174 BP 5-3-398X
7.812 1.440 500168-2 5-86-68 5-68-174 BP 5-3-108KX
8.875 1.440 500168-2 5-86-68 5-68-174 BP 5-3-368KX
9.312 3.188 500168-2 5-86-68 5-68-174 BP 5-3-288KX
9.812 2.688 500168-2 5-86-68 5-68-174 BP 5-3-128KX•
10.312 1.938 500168-2 5-86-68 5-68-174 BP 5-3-1411KX
10.312 2.440 500168-2 5-86-68 5-68-164 BP 5-3-1711KX
10.812 3.188 500168-2 5-86-68 5-68-164 BP 5-3-2261KX
10.940 3.688 — — 5-68-164 BP 5-3-3141KX
11.938 3.688 500168-2 5-86-68 5-68-164 BP 5-3-3121KX
2.500-16 Spline
9.500 2.000 500168-2 6.3-86-18 6-68-64 BP 5-3-3101KXM
2.676-18 Involute Spline
3.500 1.250 500168-2 D5C 5-68-33 BP 5-3-168KX
3.500 1.250 500168-2 — 5-68-33 BP 5-3-3231X
4.250 1.250 500168-2 D5C 5-68-33 BP 5-3-198KX
4.875 1.812 500168-2 D5C 5-68-33 BP 5-3-2971X
1710 SERIES E-6.094 (6.190-HR STYLE) D-1.938 USE KIT 5-280X OR 5-675X
2.500-15 Based On 16 Spline
7.469 1.720 — — 6-68-48X BP 6-3-3211X
11.688 2.438 500168-2 6.3-86-18 6-68-38X BP 6-3-3171KX
12.719 3.219 500168-2 6.3-86-18 6-68-38X BP 6-3-3541KX
2.500-16 Spline
6.719 1.719 500168-2 6.3-86-18 6-68-74 BP 6-3-2761KX
7.219 1.720 500168-2 — 6-68-74 BP
7.469 1.719 500168-2 6.3-86-18 6-68-74 BP 6-3-2741KX
7.970 1.719 500168-2 6.3-86-18 6-68-74 BP 6-3-2801KX
8.469 1.719 — — 6-68-74 BP 6-3-2721X
8.844 1.719 500168-2 6.3-86-18 6-68-74 BP 6-3-2631KX
9.344 2.516 500174-1 6.3-86-18 6-68-74 BP 6-3-3521KX
500168-2 lube fi tting & 5-86-68 dust cap kit, order separate
High angle slip yoke
M8 x 1.00-6H Metric tapped holes in yoke ears
Not threaded for dust cap
Relief valve in plug
Relief valve in plug
Relief valve in plug
500168-2 lube ftg. & 6.3-86-18 dust cap kit, order separate
• Part is discontinued Part is available until supply is exhausted Not sold separately
10
Important: See Safety Information in General Information Section (J300P-GI)
Page 11
J300P-3
Slip Yoke Assemblies
HD Driveshaft Style
J F Part of Slip Yoke Assembly
Slip Yoke
C/L to C/L to Lube Dust Cap Slip Yoke Assembly
End of Face of Fitting & Washer Plug Style Part
Spline Plug Kit Number Number
1710 SERIES (Continued) E-6.094 (6.190-HR STYLE) D-1.938 USE KIT 5-280X OR 5-675X
2.500-16 Spline (Continued)
9.594 1.719 500168-2 6.3-86-18 6-68-74 BP 6-3-2671KX
10.310 2.440 500168-2 6.3-86-18 6-68-38X BP 6-3-3151KX
10.312 2.440 — 6.3-86-18 6-68-38X BP 6-3-3611KXM•
Relief valve in plug; M10x1.25-6H tapped holes in yoke ears
10.719 3.219 500168-2 6.3-86-18 6-68-64 BP 6-3-3481KX
11.688 2.438 500168-2 6.3-86-18 6-68-64 BP 6-3-2651KX
11.719 3.219 500168-2 6.3-86-18 6-68-64 BP 6-3-3461KX
11.969 3.219 500168-2 6.3-86-18 6-68-64 BP 6-3-2591KX
6-3-2591KX was replaced by 6-3-3501KX
11.969 3.219 500168-2 6.3-86-18 6-68-64 BP 6-3-3501KX
12.719 3.219 500168-2 6.3-86-18 6-68-64 BP 6-3-3441KX
2.500-9 Based On 10 Spline
11.000 3.250 500168-2 D6B 6-68-63 BP 6-3-1601KX•
3.250-18 Involute Spline
4.125 1.375 500168-2 D6E 6-68-53 BP 6-3-1661KX
4.875 1.375 500168-2 D6E 6-68-53 BP 6-3-1481KX
1760 SERIES E-7.000 (7.094 FOR HR STYLE) D-1.938 USE KIT 5-407X, 5-677X
2.500-16 Spline
9.250 2.922 500168-2 6.3-86-18 6-68-74 BP 6.3-3-41KX
Metal, slip yoke plug no. is 6.3-68-14
11.156 2.469 500168-2 6.3-86-18 6-68-64 BP 6.3-3-21KX
1810 SERIES E-7.547 (7.643 FOR HR STYLE) D-1.938 USE KIT 5-281X, 5-676X
3.000-16 Spline
8.062 2.969 500168-2 6.5-86-38 6.5-68-74 BP 6.5-3-1571KX•
8.938 1.562 500168-2 6.5-86-38 6.5-68-74 BP 6.5-3-1431KX
10.250 2.375 500168-2 6.5-86-38 6.5-68-64 BP 6.5-3-1351KX
11.875 2.375 500168-2 6.5-86-38 6.5-68-64 BP 6.5-3-1371KX
11.880 3.140 500168-2 — 6.5-68-64 BP 6.5-3-1761X
Use dust cap 6.5-86-38, order separate
3.250-18 Involute Spline
5.375 1.500 500168-2 D6E 6-68-53 BP 6.5-3-1451KX
1880 SERIES E-8.094 D-2.188 USE KIT 5-308X
3.000-16 Spline
10.031 2.031 500168-2 6.5-86-38 8-68-13 BP 8-3-391KX
11.656 2.469 500168-2 6.5-86-38 8-68-13 BP 8-3-411KX
4.156-24 Involute Spline
5.031 1.750 500168-2 D9A 8-68-24 BP 8-3-431KX
Relief valve in plug
High angle slip yoke
High angle slip yoke
High angle slip yoke
High angle slip yoke
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
11
Page 12
J300P-3
Wing Bearing Style
J F Part of Slip Yoke Assembly
Boot Kit Assy Slip Yoke
C/L to End C/L to Face Lube Dust Cap Slip Yoke Part Number Assembly
of Spline of Plug Fitting & Washer Kit Plug Number Order Separately Style Part Number
5C SERIES WB STYLE P-4.531 S-1.685 KEYWAY-.563 USE KIT 5C-1X
1.564-23 Based On 24 Involute Spline
6.890 1.437 — 4-86-48 4-68-193 — WB 5C-3-21X•
6C SERIES WB STYLE P-5.531 S-1.689 KEYWAY- .563 USE KIT 6C-1X
1.939-30 Involute Spline
6.574 1.122 — 4-86-58 5-68-224 — WB 6C-3-21X
Rubber valve in plug
Rubber valve in plug
12
Important: See Safety Information in General Information Section (J300P-GI)
Page 13
J300P-3
Slip Yoke Assemblies
Slip Flange Yoke Style
J F Bolt Hole
Dust Cap & Slip Yoke
Flange Face to Pilot Diameter B - Bolt Circle Diameter # of Washer Kit Assembly
End of Spline F-Female/M-Male Diameter D-Drilled/T-Tapped Holes Part Number Part Number
1610 SERIES E-5.312 D-1.875 USE KIT 5-279X OR 5-674X
1.939-30 Involute Spline
5.250 3.749 M 4.750 .509 D 8 90-86-18 5-3-3211KX
Use lube fi tting 500174-1; order separately
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
Important: See Safety Information in General Information Section (J300P-GI)
13
Page 14
Splined Sleeves
J300P-3
Style 1
Style 3
J
End of Spline Style Tube Yoke Mates w/ Butt Splined Sleeve Slinger Assembly
to Weld Part Number Part Number Diameter Detail Part Number Part Number
Fits Tube/
F Slip Sleeve
Style 4
Style 2
Style 5
SPL140 SERIES
3.071-30 Involute Spline
6.713 1 100-30-3 140-82-21X 3.937 140-55-11 232755 140-55-21X
SPL170 SERIES
3.053-30 Involute Spline
8.539 1 36-30-102 5010631 4.243 — — 170-55-10626
8.539 1 36-30-102 5010631 4.243 — — 5010626
5010626 was replaced by 170-55-10626; Sleeve Only-No Assembly
11.043 2 5013415 5010631 4.104 — — 170-55-13487-1
11.043 2 5013415 5010631 4.104 — — 5013487-1
5013487-1 was replaced by 170-55-13487-1; Sleeve Only-No Assembly
3.465-32 Based On 34 Involute Spline
5.137 2 170-28-37 170-82-191X 4.344 — — 170-55-151
5.826 2 — 170-28-37 4.350 — — 170-55-11368
5.826 2 — 170-28-37 4.350 — — 5011368
7.205 2 170-28-37 170-82-131X 4.346 — — 170-55-81
7.590 2 170-28-37 170-82-101X 4.346 — — 170-55-61
7.972 1 110-30-5 170-82-71X 4.350 170-55-11-2 232700 170-55-21-2X
7.984 2 170-28-37 170-82-71X 4.346 170-55-51-1 170-55-51-1
8.771 2 170-28-37 170-82-71X 4.346 170-55-51-2 170-55-51-2
9.153 1 110-30-5 170-82-61X 4.350 170-55-11-1 232700 170-55-21-1X
9.559 2 170-28-37 170-82-71X 4.346 170-55-51-3 170-55-51-3
10.346 2 170-28-37 170-82-71X 4.346 170-55-51-4 170-55-51-4
Sleeve Only-No Assembly
Sleeve Only-No Assembly
Sleeve Only-No Assembly
Sleeve Only-No Assembly
Sleeve Only-No Assembly
Sleeve Only-No Assembly
Sleeve Only-No Assembly
SPL250 SERIES
3.858 (98.0mm)-36 Based On 38 Involute Spline
4.134 1 — 250-28-37 4.744 — — 250-55-61
6.909 1 120-30-* — 4.744 250-55-21 232696 250-55-31X
Sleeve Only-No Assembly
Fits all 120-30 tubes
• Part is discontinued Part is available until supply is exhausted Not sold separately
* = Tube Length
14
Important: See Safety Information in General Information Section (J300P-GI)
Page 15
J300P-3
Splined Sleeves
J
End of Spline Style Tube Yoke Mates w/ Butt Splined Sleeve Slinger Assembly
to Weld Part Number Part Number Diameter Detail Part Number Part Number
Fits Tube/
F Slip Sleeve
1310 SERIES
1.375-16 Spline
5.030 4 2-28-3707X 211256X — — — 2-55-51•
3.002-22 Based On 23 Involute Spline
3.580 5 32-38-12 2-82-1901X 3.854 2-55-141 6.5-68-64 2-55-258X
Sleeve Only-No Assembly
Material: Aluminum
1330 SERIES
3.000-24 Spline
7.524 1 — 5004948 3.355 5003494 — 5005921
3.002-22 Based On 23 Spline
4.910 5 — 2-82-1971X 3.815 5002371 6.5-68-64 2-55-02372X
4.910 5 — 2-82-1971X 3.815 5002371 6.5-68-64 5002372
5002372 was replaced by 2-55-02372X; Mat’l: alum, used w/4.500 o.d. alum tube
3.002-22 Based On 23 Involute Spline
3.910 5 — 2-82-1971X 3.854 2-55-181 6.5-68-64 2-55-268X•
4.910 1 — 2-82-1961 3.854 — — 2-55-278X
Alum slip jt. assy, used w/3.500 o.d. alum tube
Mat’l: alum, used w/4.500 o.d. alum tube
Mat’l: alum, used w/4.000 o.d. alum tube
Mat’l: alum, used w/4.000 o.d. alum tube
1350 SERIES
3.000-24 Spline
6.275 5 — 5005288 4.888 5006299 — 5007951
6.275 5 — 5005288 4.888 5006303 — 5007952
Alum slip jt. assy. used w/4.500 o.d. alum tube
Alum slip jt. assy, used w/5.000 alum tube
1410 SERIES
1.750-16 Spline
4.410 3 211140X-* 3-82-781 2.594 3-55-33 4-68-143 3-55-38X
1550 SERIES
2.000-16 Spline
4.560 3 210833X-* 4-82-211 3.320 4-55-43 4-68-43 4-55-48X
1710 SERIES
2.500-16 Spline
5.720 3 211110X-* 6-82-1131-2 5.020 6-55-43 6.5-68-13 6-55-38X
1810 SERIES
3.000-16 Spline
7.750 3 211570X-* 6.5-82-451-1 5.757 8-55-103 6.5-68-23 8-55-113X
7.750 3 211180X-* 6.5-82-451-1 5.020 8-55-33 6.5-68-23 8-55-43X
• Part is discontinued Part is available until supply is exhausted Not sold separately
* = Tube Length
Important: See Safety Information in General Information Section (J300P-GI)
15
Page 16
Slip Yoke Assemblies
Hex, Square and Round Hole
J300P-3
P
Hex
Across Flats
Lube Fitting Slip Yoke
Part Number Assembly Number
1000 SERIES K-1.500 D-.938 USE KIT 5-170X
.875 500174-1 10-3-162X
1.125 500174-1 10-3-32X
P
Square Hole
Across Flats
Lube Fitting Slip Yoke
Part Number Assembly Number
1000 SERIES K-1.500 D-.938 USE KIT 5-170X
.750 500174-1 10-3-12X
.875 500174-1 10-3-22X
1.000 500174-1 10-3-122X
P X
Round SAE
Hole Diameter Keyway Width
Lube Fitting Slip Yoke
Part Number Assembly Number
1000 SERIES K-1.500 D-.938 USE KIT 5-170X
.750 .188 500174-1 10-3-13X
.812 .250 500174-1 10-3-23X
.875 .250 500174-1 10-3-33X
1.000 .250 500174-1 10-3-83X
1.125 .312 500174-1 10-3-183X
1.250 .312 500174-1 10-3-163X
• Part is discontinued Part is available until supply is exhausted Not sold separately
16
Important: See Safety Information in General Information Section (J300P-GI)
Page 17
J300P-3
Slip Yoke Assemblies
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
SPL55 SERIES E-4.440 D-1.374 USE KIT 5-803X, 5-804X, SPL55-1X, SPL55-2X
1.615-30 Based On 31 Involute Spline
8.339 2.200 — — SR 500166-28 55-3-21X
1.616-30 Based On 31 Involute Spline
8.339 2.200 — — SR 500166-28 55-3-01672X
8.339 2.200 — — SR 500166-28 5001672
1.748-33 Based On 34 Involute Spline
9.291 2.300 — — SR 500166-29 3-3-17529X
9.291 2.300 — — SR 500166-29 5017529
5017529 was replaced by 3-3-17529X; Nickel Plated
1210 SERIES E-2.688 D-1.062 USE KIT 5-443X
1.113-24 Based On 25 Involute Spline
5.875 1.374 — — SR 500166-20 2-3-10071X•
1310 SERIES E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X
1.005-22 Based On 24 Involute Spline
6.045 1.376 1.043 .390 SR 500166-20 2-3-13461X
1.104-20 Based On 21 Involute Spline
6.000 1.496 — — SR 500166-20 2-3-9701X
1.113-24 Based On 25 Involute Spline
6.500 1.375 — — SR 500166-20 2-3-8431X
8.250 1.374 1.194 2.890 SR 2-68-153 2-3-8891X•
1.123-24 Based On 26 Involute Spline
6.040 1.494 1.142 .390 SR 500166-20 2-3-11731X
6.045 1.494 1.160 .390 SR 500166-20 2-3-13891X
1.125-10 Spline
3.469 1.625 — — SR 2-68-44 2-3-7501X
3.469 1.641 — — SR 2-68-44 2-3-11551X•
1.158-25 Based On 26 Involute Spline
6.000 1.558 — — SR 500166-20 2-3-8731X
6.000 1.558 — — SR 500166-20 2-3-9781X
1.172-16 Spline
4.875 1.500 — — SR 500166-20 2-3-1331X
1.176-26 Based On 27 Involute Spline
4.875 1.500 — — SR 500166-20 2-3-4911X
4.891 1.500 1.260 .500 SR 500166-20 2-3-9211X
Corvette w/o vibration dampener; C-bore @ Hub End
4.891 1.502 — — SR 500166-20 2-3-10501X
5.469 1.500 — — SR 500166-20 2-3-6081X
5001672 was replaced by 55-3-01672X
Nickel Plated
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
Important: See Safety Information in General Information Section (J300P-GI)
17
Page 18
Slip Yoke Assemblies
J300P-3
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1310 SERIES (Continued) E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X
1.176-26 Based On 27 Involute Spline (Continued)
5.469 1.500 — — SR 2-68-23 2-3-9191X
5.750 1.500 — — SR 500166-20 2-3-13051X
5.750 1.502 — — SR 500166-20 2-3-14771X•
5.750 1.502 — — SR 500166-20 2-3-12411X
5.750 1.602 — — SR 500166-20 2-3-15321X
6.000 1.499 — — SR 500166-20 2-3-10391X
6.420 1.502 1.232 .590 SR 500166-20 2-3-11071X
6.620 1.502 — — SR 500166-20 2-3-15341X
7.620 1.502 — — SR 500166-20 2-3-14871X•
Nickel plated yoke w/vibration dampener
7.620 1.502 — — SR 500166-20 2-3-14861X
1.201-23 Involute Spline
5.750 1.578 — — SR 2-68-343 2-3-11721X
5.750 1.578 — — SR 2-68-343 2-3-11721KX•
1.220-27 Based On 28 Involute Spline
5.390 1.496 — — SR 2-68-83 2-3-10761X
6.500 1.491 — — SR 500166-20 2-3-12981X
6.500 1.500 — — SR 500166-20 2-3-8251X
7.000 1.497 — — SR 500166-20 2-3-12671X
1.220-28 Involute Spline
6.000 1.500 — — SR 500166-20 2-3-4871X
1.250-15 Based On 16 Spline
5.380 1.700 1.262 .380 SR 2-68-23 2-3-388X•
1.284-28 Based On 30 Involute Spline
6.165 1.652 1.319 .450 SR 500166-22 2-3-13311X
6.266 1.652 1.320 .390 SR 500166-22 2-3-14001X
7.270 1.652 1.324 .450 SR 500166-22 2-3-12461X
7.420 1.652 1.319 .630 SR 500166-20 2-3-10131X
1.284-29 Based On 30 Involute Spline
6.750 1.680 — — SR 500166-22 2-3-13551X
6.750 1.680 — — — 500166-22 2-3-14791X•
9.330 1.680 — — SR 500166-22 2-3-14981X
• Part is discontinued Part is available until supply is exhausted Not sold separately
Hub diameter not ground
Nickel Plated
W/4.500” OD dampener
Nickel Plated
Nickel Plated
Toyota yoke w/slinger
Part has one wide tooth
Nickel Plated
Nickel Plated
18
Important: See Safety Information in General Information Section (J300P-GI)
Page 19
J300P-3
Slip Yoke Assemblies
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1310 SERIES (Continued) E-3.469 D-1.062 USE KIT 5-153X, 5-785X, 5-810X
1.375-10 Spline
2.562 2.120 — — SR — 2-3-9021
1.377-30 Based On 32 Involute Spline
6.102 1.731 1.387 .394 SR 500166-22 2-3-15961X
1.378-31 Based On 32 Involute Spline
4.880 1.885 — — SR 500166-22 2-3-13131X
1.390-30 Based On 31 Involute Spline
7.000 1.684 — — SR 500166-22 2-3-15631X•
1.397-31 Based On 32 Involute Spline
5.188 1.688 1.458 .880 SR 500166-22 2-3-5281X
5.500 1.885 — — SR 500166-22 2-3-10431X
1.403-21 Involute Spline
4.130 2.000 — — SR 2-68-154 2-3-9811X
1.564-24 Involute Spline
4.125 2.000 — — SR 2-68-154 2-3-9761X
1330 SERIES SR: E-3.875 OTHERS E-3.625, D-1.062 USE KIT 5-213X,5-790X,5-812X
1.113-24 Based On 25 Involute Spline
6.860 1.374 — — SR 500166-20 2-3-15471X
Nickel plated yoke w/vibration dampener
6.860 1.374 — — SR 500166-20 2-3-15461X
6.860 1.374 — — SR 500166-20 2-3-13721X
1.158-25 Based On 26 Involute Spline
6.180 1.558 — — SR 500166-20 2-3-15051X•
7.000 1.558 — — SR 500166-20 2-3-14311X
1.176-26 Based On 27 Involute Spline
5.470 1.502 — — SR 500166-20 2-3-12081X
5.470 1.502 1.218 .390 SR 500166-20 2-3-12361X
W/c-bore and vibration dampener
5.470 1.502 1.218 .390 SR 500166-20 2-3-12371X•
5.760 1.502 — — SR 500166-20 2-3-13671X•
6.417 1.502 1.216 .590 SR 500166-20 2-3-15751X•
6.760 1.502 1.217 .410 SR 500166-20 2-3-11781X
6.760 1.502 1.217 .410 SR 500166-20 5010254
5010254 was replaced by 2-3-11781X
6.760 1.502 1.217 .410 SR 2-68-23 2-3-12051X
7.290 1.558 — — SR 500166-20 2-3-14171X•
7.290 1.558 — — SR 500166-20 2-3-14191X
1.177-26 Based On 27 Involute Spline
6.760 1.500 1.225 .300 SR 2-68-23 5001433
5001433 was replaced by 2-3-01433X; Nickel Plated w/c’bore at end
6.760 1.502 1.217 .300 SR 2-68-23 2-3-01433X
Nickel Plated w/c’bore at end
Hub dia. not ground
Counterbore at hub end
Nickel Plated
Nickel Plated
Nickel Plated
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
19
Page 20
Slip Yoke Assemblies
J300P-3
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1330 SERIES (Cont'd) SR: E-3.875 OTHERS E-3.625, D-1.062 USE KIT 5-213X,5-790X,5-812X
1.201-23 Involute Spline
6.319 1.574 — — SR 2-68-343 2-3-02274X
6.319 1.574 — — SR 2-68-343 5002274
7.106 1.574 — — SR 2-68-343 5002278
7.106 1.574 — — SR 2-68-343 2-3-02278X
1.219-27 Based On 28 Involute Spline
5.920 1.500 — — SR 500166-20 2-3-13011X
5.920 1.594 — — SR 500166-20 2-3-13031X
5.922 1.585 — — SR 500166-20 2-3-11891X
1.220-27 Based On 28 Involute Spline
5.906 1.500 — — SR 500166-20 2-3-5981X
6.630 1.597 — — SR 500166-20 2-3-14061X
7.860 1.497 — — SR 500166-20 2-3-13691X
7.860 1.497 — — SR 500166-20 2-3-13701X•
1.284-29 Based On 30 Involute Spline
8.030 1.680 1.440 1.440 SR 500166-20 2-3-14031X
8.030 1.680 1.440 1.440 SR 500166-22 2-3-14261X•
9.000 1.680 — — SR 500166-22 2-3-12621X
9.000 1.680 — — SR 500166-20 2-3-14221X•
9.000 1.680 — — SR 500166-22 2-3-14211X•
1.370-16 Based On 19 Involute Spline
7.106 1.770 — — SR 5002153 5002150
5002150 was replaced by 2-3-02150X; Spline has three partial teeth missing
7.106 1.770 — — SR 5002153 2-3-02150X
1.377-30 Based On 32 Involute Spline
6.102 1.731 1.375 .393 SR 500166-22 2-3-16011X•
1.378-30 Based On 32 Involute Spline
6.102 1.731 1.375 .393 SR 500166-22 2-3-15871X
8.464 1.731 1.385 .393 SR 500166-22 2-3-02091X
8.464 1.731 1.385 .393 SR 500166-22 5002091
6.760 1.885 — — SR 500166-22 2-3-10831X
5002278 was replaced by 2-3-02278X
Same as 2-3-13701X, exc. w/o dampener
W/vibration dampener
Nickel Plated
Nickel plated yoke w/vibration dampener
W/vibration dampener
Spline has three partial teeth missing
Includes boot can
• Part is discontinued Part is available until supply is exhausted Not sold separately
20
Important: See Safety Information in General Information Section (J300P-GI)
Page 21
J300P-3
Slip Yoke Assemblies
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1330 SERIES (Cont'd) SR: E-3.875 OTHERS E-3.625, D-1.062 USE KIT 5-213X,5-790X,5-812X
1.378-31 Based On 32 Involute Spline
6.760 1.885 — — SR 2-68-143 2-3-12191X•
6.760 1.885 — — SR 500166-24 2-3-13811X•
7.250 1.885 — — SR 500166-22 2-3-14241X
7.720 1.885 — — SR 500166-24 2-3-14831X
7.720 1.885 — — SR 500166-24 2-3-13881X•
7.940 1.885 1.410 .220 SR 500166-24 2-3-10791X
8.640 1.885 — — SR 500166-22 2-3-14281X
1.390-30 Based On 31 Involute Spline
6.000 1.688 — — SR 500166-22 2-3-6041X
7.000 1.885 — — SR 500166-22 2-3-10201X
7.460 1.886 — — CV 500166-22 2-3-12961X
C.V . Yoke-Nickel Plated
1.401-32 Based On 34 Involute Spline
8.465 1.770 — — SR 500166-20 2-3-03207X
8.465 1.770 — — SR 500166-20 5003207
5003207 was replaced by 2-3-03207X
1.406-32 Based On 34 Involute Spline
8.456 1.770 — — SR 500166-22 2-3-04846X
8.456 1.770 — — SR 500166-22 5004846
5004846 was replaced by 2-3-04846X
8.464 1.770 — — SR 500166-22 3-3-08189X
8.465 1.771 1.438 .393 SR 500166-22 2-3-15891X
8.465 1.771 1.438 .393 SR 500166-22 2-3-04410X
8.465 1.771 1.438 .393 SR 500166-22 5004410
5004410 was replaced by 2-3-04410X
1350 SERIES E-3.875 D-1.188 USE KIT 5-178X OR 5-799X
1.176-26 Based On 27 Involute Spline
6.940 1.502 1.218 .410 SR 2-68-23 3-3-4281X
6.940 1.502 1.218 .410 SR 500166-20 3-3-3721X
1.201-20 Based On 23 Involute Spline
7.106 1.574 — — SR — 5004083•
1.230-20 Based On 23 Involute Spline
7.106 1.574 — — SR 2-68-343 5016999•
1.284-29 Based On 30 Involute Spline
9.512 1.681 — — SR 500166-22 5015498
9.519 1.680 — — SR 500166-22 5016138
1.326-29 Based On 30 Involute Spline
6.630 1.680 — — SR 500166-22 3-3-3931X
7.779 1.885 — — SR 500166-22 5002231
5002231 was replaced by 3-3-02231X
7.779 1.885 — — SR 500166-22 3-3-02231X
Nickel Plated
Nickel Plated
OEM Only
Nickel Plated
OEM Only
OEM Only
OEM Only
OEM Only
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
21
Page 22
Slip Yoke Assemblies
J300P-3
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1350 SERIES (Continued) E-3.875 D-1.188 USE KIT 5-178X OR 5-799X
1.375-31 Based On 32 Involute Spline
6.938 1.886 — — SR 3-68-33 3-3-6481X
6.940 1.886 — — SR 500166-24 3-3-6361X•
1.378-30 Based On 32 Involute Spline
6.100 1.731 1.388 .394 SR 500166-22 3-3-7091X
1.378-31 Based On 32 Involute Spline
5.500 1.885 — — SR 500166-24 3-3-2431X
6.938 1.886 — — SR 500166-24 3-3-5571X
6.938 1.886 — — SR 3-68-33 3-3-4261X
7.720 1.885 — — SR 500166-24 3-3-6871X
7.720 1.886 — — SR 500166-24 3-3-6441X
7.940 1.886 1.430 .220 SR 500166-24 3-3-5551X
8.432 1.885 — — SR 500166-24 5010279•
1.390-30 Based On 31 Involute Spline
6.440 1.685 — — SR 500166-22 3-3-2491X
6.570 1.684 — — SR 500166-22 3-3-5961X
7.310 1.885 — — SR 500166-23 3-3-5431X
7.460 1.885 — — CV 500166-22 3-3-4531X•
7.460 1.885 — — CV 500166-22 3-3-5861X
1.401-32 Based On 34 Involute Spline
8.465 1.770 — — SR 500166-20 5002464•
1.403-21 Involute Spline
5.310 1.830 — — SR 500166-24 3-3-848X
1.496-22 Involute Spline
7.106 1.930 — — SR 500166-24 5015119
5015119 was replaced by 3-3-15119X
7.106 1.930 — — SR 232923 5004082•
7.106 1.930 — — SR 500166-24 3-3-15119X
1.533-22 Based On 32 Involute Spline
7.106 1.930 — — SR 500166-24 5016994•
1/8” hole in welch plug
without slinger
Nickel Plated
CV yoke-OEM only
C.V . Yoke-Nickel Plated
OEM Only
Hub dia. not ground
OEM Only
OEM Only
• Part is discontinued Part is available until supply is exhausted Not sold separately
22
Important: See Safety Information in General Information Section (J300P-GI)
Page 23
J300P-3
Slip Yoke Assemblies
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1410 SERIES E-4.438 D-1.188 USE KIT 5-160X OR 5-801X
1.284-29 Based On 30 Involute Spline
8.340 1.680 — — SR 500166-22 3-3-6121X
8.340 1.680 1.440 1.440 SR 500166-22 3-3-4181X
8.340 1.680 1.440 1.440 SR 500166-22 3-3-4851X
8.340 2.161 1.440 1.440 SR 500166-22 5002035•
8.340 2.161 1.440 1.440 SR 500166-22 3-3-02035X
8.344 1.688 — — SR 500166-22 3-3-6131X
Nickel plated yoke w/vibration dampener
1.326-29 Based On 30 Involute Spline
8.340 1.680 1.440 1.440 SR 500166-22 3-3-3251X
8.340 1.680 1.440 1.440 SR 500166-22 3-3-3271X
1.378-30 Based On 32 Involute Spline
6.100 1.731 1.387 .394 SR 500166-22 3-3-04624X
6.100 1.731 1.387 .394 SR 500166-22 5004624
5004624 was replaced by 3-3-04624X
1.378-31 Based On 32 Involute Spline
6.940 1.885 — — SR 3-68-23 3-3-6471X•
6.940 1.885 — — SR 500166-24 3-3-6321X
6.940 1.885 — — SR 500166-24 3-3-6811X•
7.750 1.885 — — SR 500166-22 3-3-3811X
7.750 1.885 — — SR 500166-22 3-3-3891X
8.070 1.885 — — SR 500166-24 5001646
5001646 was replaced by 3-3-01646X; Nickel Plated
8.070 1.885 — — SR 500166-24 3-3-6421X
8.070 1.885 — — SR 500166-24 3-3-01646X
8.750 1.885 — — SR 500166-22 3-3-4401X
8.750 1.886 — — SR 500166-22 3-3-4211X
W/vibration dampener
1.390-30 Based On 31 Involute Spline
8.110 1.885 — — SR 500166-22 3-3-6001X•
Nickle Plated - OEM only
8.110 1.885 — — SR 500166-22 3-3-6661X
1.406-34 Involute Spline
8.465 1.770 — — SR 500166-22 3-3-18190X
1.500-35 Based On 37 Involute Spline
6.102 1.888 1.535 .254 SR 500166-24 5013341
1.551-33 Based On 34 Involute Spline
8.110 2.086 — — SR 500166-26 3-3-7041X
1.615-30 Based On 31 Involute Spline
7.750 2.200 — — SR 500166-28 3-3-5631X
8.340 2.200 — — SR 500166-28 3-3-4391X
8.340 2.200 — — SR 500166-28 3-3-4131X
same as 3-3-4391x except w/vibration dampener
Nickel Plated
Nickel Plated
Nickel Plated
Nickel Plated
Nickel Plated
Nickel Plated
OEM Only
Nickel Plated
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
23
Page 24
Slip Yoke Assemblies
J300P-3
For Transmission Applications
J R Counterbore
Slip Yoke Slip Yoke
C/L to End Ground Hub Style Plug Assembly
End of Spline Diameter Diameter Depth Part Number Part Number
1410 SERIES (Continued) E-4.438 D-1.188 USE KIT 5-160X OR 5-801X
1.615-30 Based On 31 Involute Spline (Continued)
8.340 2.200 1.655 .270 SR 500166-28 3-3-6541X
8.344 2.201 — — SR 500166-28 3-3-6141X•
8.344 2.201 — — SR 500166-28 3-3-3441X
1.616-30 Based On 31 Involute Spline
7.750 2.200 — — SR 500166-28 3-3-5611X
8.340 2.200 1.655 .270 SR 500166-28 5001683
5001683 was replaced by 3-3-01683X; Nickel Plated
8.340 2.200 1.655 .270 SR 500166-28 3-3-01683X
1480 SERIES E-4.438 D-1.375 USE KIT 5-188X, 5-803X OR 5-804X
1.390-30 Based On 31 Involute Spline
6.870 1.885 — — SR 500166-23 3-3-6021X
1.654-20 Involute Spline
4.560 2.380 — — SR 500166-26 3-3-3151X
1550 SERIES E-5.250 D-1.375 USE KIT 5-155X, 5-808X OR 5-809X
1.875-14 Involute Spline
4.203 3.000 — — SR 500166-31 4-3-1961X•
4.703 2.750 — — SR 500166-31 4-3-1951X
2.372-46 Involute Spline
4.880 3.125 — — SR 500166-46 4-3-2441X
Counterbore at hub end
W/vibration dampener
Nickel Plated
Nickel Plated
Hub dia. not ground
Includes fl inger
• Part is discontinued Part is available until supply is exhausted Not sold separately
24
Important: See Safety Information in General Information Section (J300P-GI)
Page 25
J300P-3
Part Number Index
1-3-18KX ..................... 3
1-3-88KX ..................... 3
2-3-01433X ..............19
2-3-02091X ..............20
2-3-02150X ..............20
2-3-02274X ..............20
2-3-02278X ..............20
2-3-03207X ..............21
2-3-04410X ..............21
2-3-04846X ..............21
2-3-06028X .................5
2-3-10021X ................4
2-3-10071X• .............17
2-3-10131X ..............18
2-3-10201X ..............21
2-3-10261KX ............... 5
2-3-10391X ..............18
2-3-1041 1X .................4
2-3-10431X ..............19
2-3-10501X ..............17
2-3-10521X .................4
2-3-10571KX• ............. 6
2-3-10641KX• ............. 5
2-3-10661X .............. 4
2-3-10761X ..............18
2-3-10791X ..............21
2-3-10801X• ................5
2-3-10831X ..............20
2-3-10871X• ...............6
2-3-1 1071X .............. 18
2-3-1 1351X• ................4
2-3-1 1491KX ............... 5
2-3-1 1551X• .............17
2-3-1 1721KX• ........... 18
2-3-1 1721X .............. 18
2-3-1 1731X .............. 17
2-3-1 1781X .............. 19
2-3-1 1891X .............. 20
2-3-1 1991KX• .............. 5
2-3-1 1991X• ...............5
2-3-12031KX .............. 6
2-3-12051X ..............19
2-3-12081X ..............19
2-3-12191X• .............21
2-3-12301KX ............... 4
2-3-12361X ..............19
2-3-12371X• .............19
2-3-1241 1X .............. 18
2-3-12421X .................4
2-3-12461X ..............18
2-3-12621X ..............20
2-3-12671X ..............18
2-3-12881X .................4
2-3-128KX ................... 4
2-3-12961X ..............21
2-3-12981X ..............18
2-3-1301 1X ........... 20
2-3-13031X ...............20
2-3-13051X ..............18
2-3-13131X ..............19
2-3-13221X ................5
2-3-1331 1X .............. 18
2-3-1331X ................17
2-3-13461X ..............17
2-3-13551X ..............18
2-3-13571X• ................5
2-3-13671X• .............19
2-3-13691X ..............20
2-3-13701X• .............20
2-3-13721X ..............19
2-3-1381 1X• .............21
2-3-13831X .................5
2-3-13881X• .............21
2-3-13891X ..............17
2-3-14001X ..............18
2-3-14031X ..............20
2-3-14061X ..............20
2-3-14171X• .............19
2-3-14191X ..............19
2-3-1421 1X• .............20
2-3-1421KX ................. 4
2-3-14221X• .............20
2-3-14241X ..............21
2-3-14261X• .............20
2-3-14281X ..............21
2-3-1431 1X .............. 19
2-3-14331X .................5
2-3-1461KX ................. 4
2-3-14771X• .............18
2-3-14791X• .............18
2-3-14831X ..............21
2-3-14861X ..............18
2-3-14871X• .............18
2-3-14981X ..............18
2-3-15051X• .............19
2-3-15101X .................4
2-3-15321X ..............18
2-3-15341X ..............18
2-3-15461X ..............19
2-3-15471X ..............19
2-3-15631X• .............19
2-3-15651X .................5
2-3-15751X• .............19
2-3-15871X ..............20
2-3-15891X ..............21
2-3-15941X .................4
2-3-15961X ..............19
2-3-1601 1X• .............20
2-3-16221X .................5
2-3-178KX ................... 4
2-3-1931KX ................. 5
2-3-198KX ................... 4
2-3-258KX ................... 4
2-3-348KX ................... 4
2-3-388X• .................18
2-3-3951KX ................. 4
2-3-4071KX ................. 4
2-3-4441KX ................. 4
2-3-4681KX ................. 6
2-3-4871X ................18
2-3-491 1X ................ 17
2-3-4951KX ................ 4
2-3-5221X ..................5
2-3-5281X ................19
2-3-5821X ..................5
2-3-5981X ................20
2-3-6041X ................21
2-3-6061KX ................. 5
2-3-6081X ................17
2-3-7171KX ................. 5
2-3-7461X ..................5
2-3-7481X• .................6
2-3-7501X ................17
2-3-7661KX ................. 4
2-3-7681KX ................. 5
2-3-7691KX ................. 5
2-3-7961KX
2-3-7981KX ................. 4
2-3-8001KX ................. 5
2-3-8021KX ................. 5
2-3-8041KX ................. 6
2-3-81 1 1KX• ................ 6
2-3-8251X ................18
2-3-831 1X .................. 5
2-3-8431X ................17
2-3-8481X ..................5
2-3-8731X ................17
2-3-8741X ..................5
2-3-881 1X• .................4
2-3-8841KX ................. 4
................. 6
2-3-8861X ...................4
2-3-8891X• ...............17
2-3-8921X ...................5
2-3-8941KX• ............... 5
2-3-9031X ............... 4
2-3-9191X ................18
2-3-921 1X ................ 17
2-3-9371X• ..................5
2-3-9701X ................17
2-3-9761X ............. 19
2-3-9781X ................17
2-3-981 1X ................ 19
2-3-9991X ...................4
2-55-02372X ............15
2-55-258X ................15
2-55-268X• ...............15
2-55-278X ................15
2-55-51• ................... 15
3-3-01646X ..............23
3-3-01683X ..............24
3-3-02035X ........... 23
3-3-02231X ..............21
3-3-04624X ..............23
3-3-08019X .................7
3-3-08189X ...............21
3-3-1 18KX ................... 7
3-3-1421KX ................. 6
3-3-1481KX ................. 7
3-3-1501KX ................. 6
3-3-151 19X .............. 22
3-3-151 1KX ................. 8
3-3-1561KX ................. 7
3-3-1601KX ................. 8
3-3-1621KX ................. 8
3-3-1641KX ................. 8
3-3-1701KX ................ 8
3-3-17529X ..............17
3-3-18190X ........... 23
3-3-1831KX ................. 8
3-3-2041KX ................. 7
3-3-2431X ................22
3-3-2471KX ................. 6
3-3-2491X ................22
3-3-2591KX ................. 6
3-3-2681KX ................ 7
3-3-2701KX ................. 6
3-3-2801KX ................. 6
3-3-2861X ...................6
3-3-2931KX• ............... 7
3-3-2991X ...................7
Important: See Safety Information in General Information Section (J300P-GI)
25
Page 26
Part Number Index
J300P-3
3-3-3001X ..................6
3-3-3121X ..................8
3-3-3151X ................24
3-3-3251X ................23
3-3-3271X ................23
3-3-331 1KX ................. 7
3-3-3381X ...................7
3-3-3401X ...................7
3-3-3441X ................24
3-3-3461X ...................7
3-3-3601X ...................7
3-3-3721X ................21
3-3-3791X ..................8
3-3-381 1X ................ 23
3-3-3871KX ................. 8
3-3-388KX ................... 7
3-3-3891X ................23
3-3-3931X ................21
3-3-398KX ................... 7
3-3-4131X ................23
3-3-4181X ................23
3-3-421 1X ................ 23
3-3-4261X ................22
3-3-4281X ................21
3-3-4391X ................23
3-3-4401X ................23
3-3-4421X ..................7
3-3-4531X• ...............22
3-3-4551X• ..................8
3-3-4651X ...................6
3-3-468KX ................... 7
3-3-4781X ...................6
3-3-4851X ................23
3-3-4871X ...................7
3-3-488KX ................... 7
3-3-508KX ................... 8
3-3-5141X• ..................8
3-3-5181KX ................. 7
3-3-541 1KX ................. 7
3-3-5431X ................22
3-3-5461X ...................6
3-3-5481KX ................. 8
3-3-5491X ...................7
3-3-5551X ................22
3-3-5571X ................22
3-3-561 1X ................ 24
3-3-5631X ................23
3-3-5861X ................22
3-3-5921KX ................. 6
3-3-5961X ................22
3-3-598KX ................... 7
3-3-6001X• ...............23
3-3-6021X ................24
3-3-6041X• .................8
3-3-6061X ...................8
3-3-6121X ................23
3-3-6131X ................23
3-3-6141X• ...............24
3-3-6201X ...................6
3-3-6321X ................23
3-3-6341X ...................7
3-3-6361X• ...............22
3-3-6381X ...................6
3-3-6421X ................23
3-3-6441X ................22
3-3-6471X• ...............23
3-3-6481X ................22
3-3-6541X ................24
3-3-661 1X .................. 7
3-3-6641X• .................8
3-3-6661X ................23
3-3-6701X ...................7
3-3-6771X ...................7
3-3-6791X ..................7
3-3-681 1X• ...............23
3-3-6831X ...................7
3-3-6871X ................22
3-3-6981X ...................6
3-3-7001X ...................8
3-3-7021X ...................8
3-3-7041X ................23
3-3-7091X ................22
3-3-748KX .................. 7
3-3-758KX ................... 6
3-3-768KX .................. 7
3-3-788KX ................... 7
3-3-798KX ................... 8
3-3-838X .....................8
3-3-848X ..................22
3-55-38X ..................15
4-3-08843KX ............... 9
4-3-1241KX ................. 9
4-3-1261KX ................. 9
4-3-141 1KX ................. 9
4-3-1431KX ................. 9
4-3-1751KX ................. 9
4-3-1921KX ................. 9
4-3-1951X ................24
4-3-1961X• ...............24
4-3-2041KX ................ 9
4-3-2121KX ................. 9
4-3-2141KX ................. 9
4-3-2441X ................24
4-55-48X ..................15
5-3-108KX ................ 10
5-3-128KX• .............. 10
5-3-141 1KX .............. 10
5-3-168KX ................ 10
5-3-171 1KX .............. 10
5-3-198KX ................ 10
5-3-2261KX .............. 10
5-3-288KX ................ 10
5-3-291 1X ................ 10
5-3-2971X ................10
5-3-3101KXM ........... 10
5-3-3121KX .............. 10
5-3-3141KX .............. 10
5-3-321 1KX ............... 13
5-3-3231X ................10
5-3-368KX ................ 10
5-3-398X ..................10
6-3-1481KX ...............11
6-3-1601KX• .............11
6-3-1661KX ...............11
6-3-2591KX
6-3-2631KX .............. 10
6-3-2651KX ...............11
6-3-2671KX ...............11
6-3-2721X ................10
6-3-2741KX .............. 10
6-3-2761KX .............. 10
6-3-2801KX .............. 10
6-3-3151KX ...............11
6-3-3171KX .............. 10
6-3-321 1X ................ 10
6-3-3441KX ...............11
6-3-3461KX ...............11
6-3-3481KX ...............11
6-3-3501KX ...............11
6-3-3521KX .............. 10
6-3-3541KX .............. 10
6-3-361 1KXM• ...........11
6-55-38X ..................15
6.3-3-21KX ................11
6.3-3-41KX ................11
6.5-3-1351KX ............11
6.5-3-1371KX ............11
6.5-3-1431KX ............11
6.5-3-1451KX ............11
6.5-3-1571KX• ..........11
...............11
6.5-3-1761X ..............1 1
8-3-391KX .................11
8-3-41 1KX .................11
8-3-431KX .................11
8-55-1 13X ................ 15
8-55-43X ..................15
10-3-121KX ................. 3
10-3-122X ................16
10-3-12X ..................16
10-3-131X ...................3
10-3-13X ..................16
10-3-162X ................16
10-3-163X ................16
10-3-183X ................16
10-3-18KX ................... 3
10-3-22X ..................16
10-3-23X ..................16
10-3-291KX ................. 3
10-3-32X ..................16
10-3-33X ..................16
10-3-51X .....................3
10-3-81X .....................3
10-3-83X ..................16
55-3-01672X ............17
55-3-21X ..................17
55-3-61X .....................3
55-3-81X .....................3
70-3-091 15X .............. 3
70-3-21X .....................3
70-3-41X .....................3
90-3-21X .....................3
90-3-41X ....................3
100-3-41X ...................3
140-55-21X ..............14
170-55-21-1X ........... 14
170-55-21-2X ........... 14
170-55-61 ................ 14
170-55-81 ................ 14
170-55-151 .............. 14
170-55-10626 .......... 14
170-55-1 1368 ........... 14
170-55-13487-1 ....... 14
170-55-51-1 ..............14
170-55-51-2 ..............14
170-55-51-3 ..............14
170-55-51-4 ..............14
250-55-61 ................ 14
250-55-31X ..............14
2/3/9021 .................... 19
5001433 .................... 19
26
Important: See Safety Information in General Information Section (J300P-GI)
Page 27
J300P-3
5001646 .................... 23
5001672 .................... 17
5001683 .................... 24
5002091 .................... 20
5002150 .................... 20
5002231 .................... 21
5002274 .................... 20
5002278 .................... 20
5002372 .................... 15
5003207 .................... 21
5004410 .................... 21
5004624 .................... 23
5004846 .................... 21
5005921 .................... 15
5006028 ...................... 5
5007951 .................... 15
5007952 .................... 15
5008019 ...................... 7
5008843 ...................... 9
50091 15 ...................... 3
5010254 .................... 19
5010626 .................... 14
501 1368 .................... 14
5013341 .................... 23
5013487-1 ................ 14
50151 19 .................... 22
5015498 .................... 21
5016138 .................... 21
5017529 .................... 17
21 1391X ..................... 6
5002035• ................. 23
5002464• ................. 22
5004082• ................. 22
5004083• ................. 21
5010279• ................. 22
5016994• ................. 22
5016999• ................. 21
5C-3-21X• ................ 12
6C-3-21X ................. 12
Part Number Index
Important: See Safety Information in General Information Section (J300P-GI)
27
Page 28
Dana Aftermarket Group
PO Box 1000
Maumee, Ohio 43537
Warehouse Distributors: 1.800.621.8084
OE Dealers: 1.877.777.5360
www.SpicerParts.com
J300P-3 Printed in U.S.A.
Copyright Dana Limited, 2014.
All rights reserved. Dana Limited.
Loading...