Page 1
Driveline Components Catalog
Flange Yokes
J300P-2
March 2012
Supersedes Section 2
Dated January 2008
Find the flange yokes that are built to your vehicle’s original equipment
specifications, based on the design and series of the part.
Product pictured is intended to be a representation of product category.
Page 2
HOW TO USE THIS CATALOG
To identify a Flange Yoke, two pieces of information are needed:
1). The Design of the Part
SNAP RING BEARING PLATE BEARING STRAP
J300P-2
2). The Series of the Part
• SPL® fl ange yokes that are spring tab or strap design can be found on pages 3 through 4.
• Flange yokes that are snap ring
• Flange yokes that are bearing plate design can be found on pages 9 through 11.
• A part number index is provided on page 12.
Footnotes for parts and assemblies that are discontinued, will be discontinued or replaced upon
depletion of stock, or not sold separately, are indicated by a symbol next to the part number. Match
the symbol to the appropriate status at the bottom of the page. All other footnotes are located
immediately below the yoke dimensional data.
or strap
design can be found on pages 5 through 8.
2
Important: See Safety Information in General Information Section (J300P-GI)
Page 3
J300P-2
Spicer Life Series™ Flange Yokes
Figure 1
Figure 2
Figure 3
Side View of
Figures 1, 2 & 4
Side View of
Figure 4
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
Figure 5
Figure 6
Figures 3, 5 & 6
SPL90 SERIES E-5.380 (HR STYLE 4.958) D-1.625 USE KIT NO. SPL90X
5.906 5.118 .478-D 8 3.544F 3.281 2 90-2-29
6.688 6.124 .375-D 8 5.312M 2.750 5 90-2-49-1
B.S./H.R.style w/brake pilot.
6.688 6.124 .375-D 8 6.624M 3.280 2 90-2-19
8.000 7.250 .375-D 8 6.438M 2.750 5 90-2-39-1
B.S./H.R.style w/brake pilot.
8.000 7.250 .375-D 8 7.750M 2.750 5 90-2-69-1
Bearing strap/half round style
Metric fl ange
SPL100 SERIES E-5.380 D-1.626 USE KIT SPL100-1X
8.000 7.250 .375-D 8 6.438M 2.750 5 100-2-169-1
8.000 7.250 .399-D 8 7.750M 3.250 4 100-2-159•
SPL140 SERIES E-5.028 D-1.937 USE KIT SPL140-1X
8.000 7.250 .375-D 8 7.750M 3.070 5 140-2-99-1
8.000 7.250 .375-D 8 7.750M 3.070 2 140-2-59
8.000 7.250 .380-D 8 6.438M 2.953 5 140-2-69-1•
8.000 7.250 .396-D 12 7.750M 3.070 2 140-2-19•
8.000 7.250 .439-D 12 7.750M 3.070 2 140-2-29•
Mates with std. 1710 series companion fl ange
Mates with std. 1710 series companion fl ange
1/2 Rnd part W/spec GMC bolt hole size
10mm bolt holes on 1810 bolt pattern
Mates with std. 1810 series companion fl ange
SPL170 SERIES E-6.026 (HR STYLE 6.456) D-2.166 USE KIT SPL170X
7.087 5.906 .551-D 4 — 3.425 1 170-2-15
7.087 5.906 .551-D 4 — 4.311 5 170-2-35
8.000 7.250 .378-D 8 7.750M 3.208 4 170-2-49
Mates with std. 1710 series companion fl ange
180mm fl ange w/serrated fl ange face
180mm fl ange w/serrated fl ange face
Continued on next page
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
3 Important: See Safety Information in General Information Section (J300P-GI)
Page 4
Spicer Life Series™ Flange Yokes
J300P-2
Figure 1
Figure 2
Figure 3
Side View of
Figures 1, 2 & 4
Side View of
Figure 4
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
Figure 5
Figure 6
Figures 3, 5 & 6
SPL170 SERIES (Continued) E-6.026 (HR STYLE 6.456) D-2.166 USE KIT SPL170X
8.000 7.250 .440-D 12 7.750M 3.386 6 170-2-59-1
8.000 7.250 .441-D 12 7.750M 3.208 2 170-2-19
8.000 7.250 .479-D 12 7.750M 3.208 2 170-2-29•
8.000 7.250 .479-D 12 7.750M 3.375 6 170-2-39-1
Mates with std. 1810 series companion fl ange
12.2mm bolt holes on 1810 bolt pattern
12.2mm bolt holes on 1810 bolt pattern
SPL250 SERIES E-5.986 D-2.362 USE KIT SPL250X
7.087 5.906 .591-D 4 — 3.583 5 250-2-10491-1
7.087 5.906 .551-D 4 — 3.583 1 250-2-15
8.000 7.250 .439-D 12 7.750M 3.500 2 250-2-19
250-2-19 was replaced by 250-2-49-1 ; Mates with std. 1810 series companion fl ange
8.000 7.250 .440-D 12 7.750M 3.524 6 250-2-49-1
8.000 7.250 .479-D 12 7.750M 3.524 6 250-2-39-1
180mm fl ange w/serrated fl ange face
180mm fl ange w/serrated fl ange face
Half round metric fl ange
Half round metric fl ange
• Part is discontinued Part is available until supply is exhausted Not sold separately
4
Important: See Safety Information in General Information Section (J300P-GI)
Page 5
J300P-2
Flange Yokes
Snap Ring Design
Figure 1 Figure 2
Figure 3
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1000 SERIES E-1.500 D-.938 USE KIT NO. 5-170X
3.375 2.750 .312-D 4 2.250M 1.562 1 10-2-29
1100 SERIES E-2.656 D-.938 USE KIT NO. 5-101X OR 5-111X
3.375 2.750 .312-D 4 2.250F 1.188 1 1-2-49•
3.375 2.750 .312-D 4 2.250M 1.188 1 1-2-39
1210 SERIES E-2.688 D-1.062 USE KIT NO. 5-443X OR 5-736X
3.406 2.750 .328-D 4 2.250M 1.484 1 2-2-899
3.710 3.125 .334-D 4 2.250M 1.200 1 2-2-1419•
3.710 3.125 .334-D 4 2.250M 1.200 1 2-2-1579
4.360 3.500 .484-D 4 2.000F 1.625 1 2-2-1049
Fits several Nissan & Toyota pick-up trucks
Bolts holes are equally spaced
2-2-1579 was replaced by 2-2-1419
1310 SERIES E-3.469 D-1.062 USE KIT NO. 5-153X, 5-785X, 5-810X, 5-1200X
3.625 2.875 .380-D 4 — 1.375 1 2-2-349
3.875 3.125 .375-D 4 2.375F 1.375 1 2-2-389
3.875 3.125 .375-D 4 2.375M 1.625 1 2-2-459
3.875 3.125 .375-D 4 2.375M 1.375 1 2-2-329
3.875 3.125 .406-D 4 2.375M 1.625 1 2-2-1609
4.016 3.203 .406-D 4 1.969M 1.781 1 2-2-1309
4.080 3.198 .400-D 4 1.968M 1.781 1 2-2-1899
4.150 3.344 .406-D 4 1.812M 1.770 1 2-2-1679
4.158 3.346 .406-D 4 2.559M 1.766 1 2-2-1519
4.160 3.346 .406-D 4 2.375M 1.516 1 5006832
4.160 3.346 .406-D 4 2.375M 1.516 1 2-2-06832
4.330 3.661 .446-D 4 1.811M 1.634 1 5001902
5001902 was replaced by 2-2-01902 ; Bolts holes are equally spaced
4.330 3.661 .446-D 4 1.811M 1.634 1 2-2-01902
10 mm bolt holes, equally spaced
10 mm bolt holes, equally spaced
5006832 was replaced by 2-2-06832
Bolts holes are equally spaced
Metric fl ange
Continued on next page
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
5 Important: See Safety Information in General Information Section (J300P-GI)
Page 6
Flange Yokes
Snap Ring Design
J300P-2
Figure 1
Figure 2
Figure 3
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1310 SERIES (Continued) E-3.469 D-1.062 USE KIT NO. 5-153X, 5-785X, 5-810X, 5-1200X
4.500 3.500 .500-D 4 2.000F 1.650 1 2-2-939
4.580 3.750 .440-D 4 2.750M 1.190 1 2-2-1039•
4.678 3.740 .469-D 4 2.558M 1.781 1 2-2-1729
4.625 3.750 .406-D 4 2.559M 1.772 1 2-2-1799
4.625 3.750 .438-D 4 2.750M 1.375 1 2-2-479
4.719 3.750 .481-D 4 2.558M 1.781 1 2-2-1949
4.740 3.740 .478-D 4 1.964M 1.780 1 2-2-2029
4.750 3.750 .503-D 4 2.750M 2.000 1 2-2-1789
4.906 3.937 .489-D 4 2.162F 1.930 1 2-2-1989
5.219 4.250 .484-D 4 2.000F 1.625 1 2-2-1379
5.750 4.750 .507-D 4 3.750M 1.375 1 2-2-579
Bolt holes are equally spaced. Part has hole thru center.
10 mm bolt holes, equally spaced
12 mm bolt holes equally spaced.
Bolts holes are equally spaced
10 mm bolt holes, equally spaced
Bolt holes are equally spaced. Part has hole thru center.
Bolt holes are equally spaced. Part has hole thru center.
1330 SERIES E-3.875 D-1.062 USE KIT NO. 5-213X, 5-790X, 5-812X, 5-1203X
3.880 3.000 .487-D 4 2.436F 1.618 1 2-2-01474
4.469 3.500 .484-D 4 2.000F 1.625 1 2-2-949
4.528 3.661 .446-D 4 1.811M 1.653 1 5001904
4.528 3.661 .446-D 4 1.811M 1.653 1 2-2-01904
4.625 3.750 .438-D 4 2.750M 1.562 1 2-2-1209
4.625 3.750 .438-D 4 2.750M 1.562 1 2-2-489
4.960 3.938 .489-D 4 2.161F 1.930 1 2-2-1879•
5.118 3.674 .482-D 4 1.811M 1.653 1 2-2-02768
5.156 4.250 .453-D 4 3.125F 1.688 1 2-2-1399
Bolts holes are equally spaced
5001904 was replaced by 2-2-01904
Bolts holes are equally spaced
Bolts holes are equally spaced
Continued on next page
• Part is discontinued Part is available until supply is exhausted Not sold separately
6
Important: See Safety Information in General Information Section (J300P-GI)
Page 7
J300P-2
Flange Yokes
Snap Ring Design
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1330 SERIES (Continued) E-3.875 D-1.062 USE KIT NO. 5-213X, 5-790X, 5-812X, 5-1203X
5.360 4.251 .500-D 4 2.560F 1.618 1 5002313
5.360 4.251 .500-D 4 2.560F 1.618 1 2-2-02313
5.875 4.750 .500-D 4 2.953F 1.730 1 2-2-03489
12 mm bolt holes equally spaced. Part has hole thru ctr.
5002313 was replaced by 2-2-02313
1350 SERIES E-3.875 D-1.188 USE KIT NO. 5-178X OR 5-799X
4.500 3.750 .438-D 4 2.750M 1.281 1 3-2-809
4.625 3.750 .438-D 4 2.750M 1.562 1 3-2-119
5.250 4.250 .470-T 4 2.680F 1.625 1 3-2-1699
5.250 4.250 .500-D 4 2.000F 1.625 1 3-2-1579•
5.250 4.250 .500-D 4 2.560F 1.618 1 3-2-1879
5.360 4.250 .472-T 4 2.000F 1.625 1 3-2-1619
5.750 4.750 .500-D 4 2.953F 1.750 1 3-2-1859
5.812 3.938 .489-D 4 2.161F 1.913 1 5010269•
6.406 5.500 .453-D 4 3.562F 1.844 1 3-2-699•
Bolt holes are equally spaced. Part has hole thru center.
12mm threaded holes, Metric fl ange
Bolt holes are equally spaced. Part has hole thru center.
12mm threaded holes, Metric fl ange
Bolt holes are equally spaced. Part has hole thru center.
Bolt holes are equally spaced. Part has hole thru center.
1410 SERIES E-4.438 D-1.188 USE KIT NO. 5-160X OR 5-801X
4.234 3.750 .484-D 4 2.750M 1.688 1 3-2-1329
4.625 3.750 .438-D 4 2.750F 1.688 1 3-2-299
4.625 3.750 .438-D 4 2.750M 1.688 1 3-2-159
4.625 3.750 .438-D 4 2.750M 1.938 1 3-2-439
4.724 3.996 .394-D 8 2.954F 2.531 2 3-2-1159
4.760 3.938 .484-D 4 3.149M 1.690 3-2-1549
Bolt holes are on 36 degrees
5.094 4.750 .480-D 4 3.750M 1.750 2 3-2-1779
5.240 4.250 .500-D 4 2.000F 1.620 1 3-2-1819
Part has hole thru center
5.290 4.250 .500-D 4 2.560F 1.736 1 3-2-04617
Bolts holes are equally spaced
5.352 4.250 .512-D 4 2.680F 1.620 1 3-2-1759
Bolt holes are equally spaced. Part has hole thru center.
5.352 4.250 .472-T 4 2.680F 1.620 1 3-2-1709
12mm tapped holes/OEM only
5.750 4.750 .500-D 4 2.953F 2.000 1 3-2-1839
Bolt holes are equally spaced. Part has hole thru center.
5.750 4.750 .509-D 4 3.750M 2.000 1 3-2-1789
Bolts holes are equally spaced
5.812 4.750 .531-D 4 3.750M 2.000 1 3-2-939
5.875 4.750 .480-D 4 3.750M 2.000 1 3-2-1519•
5.875 4.750 .500-D 4 3.750M 2.000 1 3-2-429
5.875 4.750 .500-D 4 3.750M 1.750 1 3-2-549
5.875 4.750 .500-D 4 3.750M 1.500 1 3-2-559
12mm threaded holes equally spaced
6.375 5.500 .438-D 4 3.562F 1.844 1 3-2-709
6.750 5.750 .484-D 4 4.803F 2.000 3 3-2-1659-1
Bearing strap style yoke w/brake pilot and bolt pattern
6.875 6.125 .375-D 8 6.875M 2.000 2 3-2-309
Flange has pilot for brake
Metric fl ange
• Part is discontinued Part is available until supply is exhausted Not sold separately
7 Important: See Safety Information in General Information Section (J300P-GI)
Page 8
Flange Yokes
Snap Ring Design
J300P-2
Figure 1
Figure 2
Figure 3
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1480 SERIES E-4.438 D-1.375 USE KIT NO. 5-188X, 5-803X OR 5-804X
5.354 4.252 .509-D 4 2.680F 1.800 1 3-2-1769
5.750 4.750 .500-D 4 3.750M 2.000 1 3-2-479
5.850 4.750 .510-D 4 2.953F 2.000 1 3-2-1869
5.875 4.250 .472-T 4 2.680F 1.800 1 3-2-1719
5.875 4.750 .500-D 4 3.750M 2.000 1 3-2-609
5.875 4.750 .500-D 4 3.750M 1.500 1 3-2-489
6.875 6.125 .386-D 8 5.312M 1.938 2 3-2-909
6.875 6.125 .386-D 8 6.625M 2.000 2 3-2-499
Bolt holes are equally spaced. Part has hole thru center.
Bolt holes are equally spaced. Part has hole thru center.
Flange has pilot for brake
1550 SERIES E-5.250 D-1.375 USE KIT NO. 5-155X, 5-808X OR 5-809X
4.724 3.996 .400-D 8 2.953F 3.150 1 4-2-1129
5.750 4.750 .484-D 4 3.750M 1.500 1 4-2-1149
5.750 4.750 .500-D 4 3.750M 2.000 1 4-2-819
5.760 4.724 .559-D 4 3.750M 2.000 1 5001720
5.760 4.724 .559-D 4 3.750M 2.000 1 4-2-01720
5.774 4.750 .512-D 4 3.750M 2.000 1 4-2-669
5.875 4.750 .500-D 4 3.750F 1.500 1 4-2-759
5.875 4.750 .500-D 4 3.750M 1.500 1 4-2-679
6.156 5.250 .453-D 8 3.750F 2.500 2 4-2-829
6.412 5.500 .453-D 8 3.750F 2.500 2 4-2-849
6.875 6.125 .375-D 8 6.625M 2.000 2 4-2-689
6.875 6.125 .386-D 8 5.312M 2.000 2 4-2-699
6.875 6.125 .406-D 8 5.312M 2.000 2 4-2-1109
7.000 6.124 .509-D 8 3.375F 2.000 2 4-2-1159
5001720 was replaced by 4-2-01720
Flange has pilot for brake
Flange has pilot for brake
• Part is discontinued Part is available until supply is exhausted Not sold separately
8
Important: See Safety Information in General Information Section (J300P-GI)
Page 9
J300P-2
Flange Yokes
Bearing Plate Design
Figure 1
Figure 4
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
Figure 2
Figure 5
T-Tapped Holes F-Female Centerline Number
Figure 3
Figure 6
Side View of
Figures 1, 2, 4 & 6
Side View of
Figures 3 & 5
1610 SERIES E-5.312 D-1.875 USE KIT N0. 5-279X, 5-674X
6.875 6.125 .375-D 8 5.312M 2.750 2 5-2-599
6.875 6.125 .375-D 8 5.312M 1.875 2 5-2-989
6.875 6.125 .375-D 8 5.312M 2.750 5 5-2-599-1
6.875 6.125 .375-D 8 5.375F 1.875 2 5-2-1089
6.875 6.125 .375-D 8 5.375F 2.750 2 5-2-249
6.875 6.125 .375-D 8 6.625M 2.750 2 5-2-279
6.875 6.125 .375-D 8 6.625M 1.875 2 5-2-379
6.875 6.125 .440-D 12 6.625M 2.750 6 5-2-1159•
8.000 7.250 .375-D 8 6.435M 2.750 5 5-2-1249-1
8.000 7.250 .375-D 8 6.435M 2.750 3 5-2-709-1•
8.000 7.250 .375-D 8 6.435M 2.750 2 5-2-709
8.000 7.250 .375-D 8 7.750M 2.750 2 5-2-629
8.000 7.250 .375-D 8 7.750M 1.875 2 5-2-619
Flange has pilot for brake
Flange has pilot for brake
B.S./H.R.style w/brake pilot.
Part has opening cast thru web
B.S./H.R.style w/brake pilot.
B.S./H.R.style w/brake pilot.
Flange has pilot for brake
Part has opening cast thru web
1710 SERIES E-6.094 (HR STYLE-6.190) D-1.938 USE KIT NO. 5-280X, 5-675X
7.087 5.906 .590-D 4 .000 3.268 4 6-2-25
8.000 5.118 .472-D 4 .000 3.189 4 6-2-15
8.000 7.250 .375-D 8 6.438M 3.000 5 6-2-1439-1
8.000 7.250 .375-D 8 6.438M 3.000 2 6-2-789
8.000 7.250 .375-D 8 7.750M 2.000 2 6-2-769
8.000 7.250 .375-D 8 7.750M 3.000 5 6-2-749-1
180 mm fl ange w/serrated fl ange face
150 mm fl ange w/serrated fl ange face
B.S./H.R.style w/brake pilot.
Flange has pilot for brake
Part has opening cast thru web
Continued on next page
• Part is discontinued Part is available until supply is exhausted Not sold separately
Important: See Safety Information in General Information Section (J300P-GI)
9 Important: See Safety Information in General Information Section (J300P-GI)
Page 10
Flange Yokes
Bearing Plate Design
J300P-2
Figure 1
Figure 2
Figure 3
Figure 4
Side View of
Figures 1, 2, 4, 6 & 8
Side View of
Figure 5
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
Figure 6
T-Tapped Holes F-Female Centerline Number
Figure 7
Figure 8
Figures 3, 5 & 7
1710 SERIES (Continued) E-6.094 (HR STYLE-6.190) D-1.938 USE KIT NO. 5-280X, 5-675X
8.000 7.250 .375-D 8 7.750M 3.000 2 6-2-749
8.000 7.250 .375-D 8 7.750M 2.000 2 6-2-959•
8.000 7.250 .375-D 8 7.750M 3.000 2 6-2-1239
8.000 7.250 .375-D 8 8.000M 3.000 2 6-2-759
8.000 7.250 .396-D 12 7.750M 3.000 5 6-2-14898
8.000 7.250 .438-D 16 6.438M 3.000 8 6-2-1219
8.000 7.250 .438-D 12 7.750M 3.000 6 6-2-779
8.000 7.250 .438-D 8 7.750M 3.000 5 6-2-739-1
8.000 7.250 .438-D 8 7.750M 2.500 2 6-2-1349
8.000 7.250 .438-D 8 7.750M 3.000 2 6-2-739
8.000 7.250 .438-D 8 7.750M 3.000 2 6-2-1159
8.000 7.250 .438-D 12 7.750M 3.000 7 6-2-779-1
8.000 7.250 .438-D 12 7.750M 2.000 6 6-2-839
Bolts rotated 22.5 degrees for brake applications
Flange has pilot for brake; Bearing strap/half round style
Part has opening cast thru web
Flange has pilot for brake
10 mm bolt holes, equally spaced
Flange has pilot for brake
Flange has pilot for brake
Part has opening cast thru web
Part has opening cast thru web
1760 SERIES E-7.000 (HR STYLE-7.094) D-1.938 USE KIT NO. 5-407X, 5-677X
8.000 7.250 .438-D 12 7.750M 3.375 6 6.3-2-19
8.000 7.250 .438-D 12 7.750M 3.375 7 6.3-2-19-1
Bearing strap/half round style
1810 SERIES E-7.547 (HR STYLE-7.643) D-1.938 USE KIT NO. 5-281X, 5-676X
8.000 7.250 .438-D 12 6.438M 3.312 4 6.5-2-349
8.000 7.250 .438-D 12 7.750M 3.375 6 6.5-2-329
8.000 7.250 .438-D 12 7.750M 3.375 7 6.5-2-329-1
8.125 7.250 .438-D 12 7.750M 2.594 6 6.5-2-359
• Part is discontinued Part is available until supply is exhausted Not sold separately
10
Important: See Safety Information in General Information Section (J300P-GI)
Page 11
J300P-2
Flange Yokes
Bearing Plate Design
A B - Bolt Holes C G
Flange or Bolt Diameter Number Pilot Diameter Flange Illustration Spicer
Swing Circle D-Drilled of M-Male Face to Figure Part
Diameter Diameter
T-Tapped Holes F-Female Centerline Number
1880 SERIES E-8.094 D-2.188 USE KIT NO. 5-308X
9.562 8.250 .625-D 8 7.000M 2.500 1 8-2-119
9.562 8.250 .625-D 8 7.000M 3.500 1 8-2-109
• Part is discontinued Part is available until supply is exhausted Not sold separately
11 Important: See Safety Information in General Information Section (J300P-GI)
Page 12
PART NUMBER INDEX
J300P-2
1-2-39 ........................................5
1-2-49• .......................................5
2-2-329 ......................................5
2-2-349 ......................................5
2-2-389 ......................................5
2-2-459 ......................................5
2-2-479 ......................................6
2-2-489 ......................................6
2-2-579 ......................................6
2-2-899 ......................................5
2-2-939 ......................................5
2-2-949 ......................................6
2-2-1049 ....................................5
2-2-1209 ....................................6
2-2-1309 ....................................5
2-2-1379 ....................................6
2-2-1399 ....................................6
2-2-01474 ..................................6
2-2-1519 ....................................5
2-2-1579 ....................................5
2-2-1609 ....................................5
2-2-1679 ....................................5
2-2-1729 ....................................6
2-2-1789 ....................................6
2-2-1799 ....................................6
3-2-489 ......................................8
3-2-499 ......................................8
3-2-549 ......................................7
3-2-559 ......................................7
3-2-609 ......................................8
3-2-699• .....................................7
3-2-709 ......................................7
3-2-809 ......................................7
3-2-909 ......................................8
3-2-939 .......................................7
3-2-1159 ....................................7
3-2-1329 ....................................7
3-2-1519• ...................................7
3-2-1549 ....................................7
3-2-1579• ...................................7
3-2-1619 ....................................7
3-2-1659-1 .................................7
3-2-1699 ....................................7
3-2-1719 ....................................8
3-2-1759 ....................................7
3-2-1769 ....................................8
3-2-1779 ....................................7
3-2-1789 ....................................7
3-2-1819 ....................................7
3-2-1839 ....................................7
5-2-599 ......................................9
5-2-599-1 ...................................9
5-2-619 ......................................9
5-2-629 ......................................9
5-2-709-1• ..................................9
5-2-709 ......................................9
5-2-989 ......................................9
5-2-1089 ....................................9
5-2-1159• ...................................9
5-2-1249-1 .................................9
6-2-15 ........................................9
6-2-25 ........................................9
6-2-739-1 .................................10
6-2-739 ....................................10
6-2-749-1 ...................................9
6-2-749 ....................................10
6-2-759 ....................................10
6-2-769 ......................................9
6-2-779 ....................................10
6-2-779-1 .................................10
6-2-789 ......................................9
6-2-839 ....................................10
6-2-959• ...................................10
6-2-1159 ..................................10
6-2-1219 ..................................10
2-2-1899 ....................................5
2-2-01902 ..................................6
2-2-01904 ..................................6
2-2-1949 ....................................6
2-2-1989 ....................................6
2-2-2029 ....................................6
2-2-02313 ..................................7
2-2-02768 ..................................6
2-2-03489 ..................................7
2-2-06832 ..................................5
2-2-1039• ...................................6
2-2-1419• ...................................5
2-2-1879• ...................................6
3-2-119 ......................................7
3-2-159 ......................................7
3-2-299 ......................................7
3-2-309 ......................................7
3-2-429 ......................................7
3-2-439 ......................................7
3-2-479 ......................................8
3-2-1859 ....................................7
3-2-1869 ....................................8
3-2-1879 ....................................7
3-2-04617 ..................................7
4-2-669 ......................................8
4-2-679 ......................................8
4-2-689 ......................................8
4-2-699 ......................................8
4-2-759 ......................................8
4-2-819 ......................................8
4-2-829 ......................................8
4-2-849 ......................................8
4-2-1109 ....................................8
4-2-1129 ....................................8
4-2-1149 ....................................8
4-2-1159 ....................................8
4-2-01720 ..................................8
5-2-249 ......................................9
5-2-279 ......................................9
5-2-379 ......................................9
6-2-1239 ..................................10
6-2-1349 ..................................10
6-2-1439-1 .................................9
6-2-14898 ................................10
6.3-2-19 ...................................10
6.3-2-19-1 ................................10
6.5-2-329 .................................10
6.5-2-329-1 ..............................10
6.5-2-349 .................................10
6.5-2-359 .................................10
8-2-109 ....................................11
8-2-119 ....................................11
10-2-29 ......................................5
90-2-19 ......................................3
90-2-39-1 ...................................3
90-2-49-1 ...................................3
90-2-69-1 ...................................3
90-2-29 ......................................3
100-2-159• .................................3
100-2-169-1 ...............................3
12
Important: See Safety Information in General Information Section (J300P-GI)
Page 13
J300P-2
140-2-19• ...................................3
140-2-29• ...................................3
140-2-59 ....................................3
140-2-69-1• ................................3
140-2-99-1 .................................3
170-2-15 ....................................3
170-2-19 ....................................4
170-2-29• ...................................4
170-2-35 ....................................3
170-2-39-1 .................................4
170-2-49 ....................................3
170-2-59-1 .................................4
250-2-15 ....................................4
250-2-19 ....................................4
250-2-39-1 .................................4
250-2-49-1 .................................4
250-2-10491 ..............................4
5001720 .....................................8
5001902 .....................................5
5001904 .....................................6
PART NUMBER INDEX
5002313 .....................................7
5006832 .....................................5
5010269• ...................................7
13 Important: See Safety Information in General Information Section (J300P-GI)
Page 14
NOTES
J300P-2
14
Important: See Safety Information in General Information Section (J300P-GI)
Page 15
J300P-2
Dana Holding Corporation strives to publish catalogs that are as accurate and user-friendly as possible.
Continuous improvement is our ongoing mission. Therefore, we welcome any and all of your comments.
Please forward your comments with any suggested improvements or corrections to our Catalog Department
via Fax or mail.
Fax: Product Management / Catalog Department
(419) 866-3925
Mail: Dana Holding Corporation
Aftermarket Group
Attn: Product Management / Catalog Department
PO Box 321
Toledo, OH 43697-0321
Comments and Suggested Improvement/Corrections Page Number Part Number
CATALOG COMMENT FORM
15 Important: See Safety Information in General Information Section (J300P-GI)
Page 16
Dana Aftermarket Group
PO Box 1000
Maumee, Ohio 43537
Warehouse Distributors: 1.800.621.8084
OE Dealers: 1.877.777.5360
www.SpicerParts.com
J300P-2 Printed in U.S.A.
Copyright Dana Limited, 2014.
All rights reserved. Dana Limited.
Loading...