Spicer J300P-1 User Manual

Driveline Components Catalog
Companion Flanges

J300P-1

November 2012

Supersedes Section 1

Dated November 2007

Updated 9-19-2013

• Page 17: removed 1.750 Spline and 2.000 Spline from 1610 &

1650/1710 Series Tapered Hole Companion Flanges

Product pictured is intended to be a representation of product category.

HOW TO USE THIS CATALOG

J300P-1

To identify any splined companion fl ange, there are ten pieces of required information:

1. Center Hole type (Splined, Round or Tapered hole)

2. Spline size and tooth count

3. Pilot diameter and type (Male / Female)

4. Bolt circle diameter

5. Bolt hole diameter and if the hole is drilled or tapped (drilled-D or tapped-T)

6. Number of bolt holes

7. Ground hub diameter (where applicable)

8. Brake drum pilot diameter

9. Length of through hole

10. Flange face to end of hub

Example: to fi nd a companion fl ange with a 2.143-41 involute splined hole, a 7.750 female pilot
that includes twelve bolts:

1. Find the Splined Hole section of this catalog;

2. Find the 2.143-41 Involute Spline sub-heading;

3. Find the Female Pilot diameter of 7.750

4. Find the Bolt circle diameter of 7.250

5. Find the Drilled Bolt hole diameter of .440

6. Find a Number of bolt holes of 12

7. Find the Ground hub diameter of 2.939

8. Find the Brake drum pilot diameter (not applicable in this example)

9. Find the Length of through hole of 2.495

10. Find the Flange face to end of hub of 3.500
Locate the part number that matches the dimension of your part: example 6.5-1-2941
Be sure to read any notes that are provided.

J300P-1

COMPANION FLANGES

1

Spline Hole

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

2.114-32 Involute Spline

2.114 5.312 M 6.125 .385 D 8 — 3.000 2.250 2.844 3 5-1-6731X 232200 5-1-6721 1610

2.114 6.625 F 6.125 .375 D 8 — 3.000 2.245 2.844 3 5-1-6701X 232200 5-1-6691 1610

2

.424 deep counterbore at hub end; 5-1-6691 will be replaced by 5-1-6701X when supply is exhausted

2.143-41 Involute Spline

2.143 7.750 F 7.250 .440 D 12 — 2.939 2.495 3.500 4 6.5-1-2941 1810

2.149-16 Spline

2.149 6.625 F 6.125 .385 D 8 — 2.938 3.000 3.750 3 5-1-2551• 1610

3

4 5 6 7 8 9 10

F

i

g
u

r

e

.424 deep counterbore at hub end

Part

Number

2

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

HOW TO USE THIS CATALOG

To identify a non- splined companion fl ange, there are nine pieces of required information:

1. Center hole type (Round or Tapered hole)

2. Type of fl ange (Circular or Rectangular)

3. Series

4. Hole size/ bore diameter

5. Keyway width

6. Bolt hole diameter and if the hole is drilled or tapped (drilled-D or tapped-T)

7. Ground hub diameter (where applicable)

8. Length of through hole

9. Flange face to end of hub

Example: to fi nd a 1610 Series circular type companion fl ange with a straight round hole, a 3.500 bore
diameter, a keyway sidth of .875, with .375-24 tapped bolt holes, 6.8750 hub diameter, and the fl ange
face to end of hub dimension of 5.0 (see example below):

1/2. Find the Circular Type with Straight Round Hole section of this catalog

3. Find the 1610 Series sub-heading

4. Find the bore diameter of 3.500

5. Find the keyway width of .875

6. Find the tapped bolt hole diameter of .375-24

7. Find the hub diameter of 6.8750

8. Find the fl ange face to end of hub of 5.0000
Locate the part number that matches the dimension of your part: example 5-1-883-1
Be sure to read any notes that are provided.

J300P-1

1

COMPANION FLANGES

2

Circular Type - Straight Round Hole

D K C E F
Pilot Flange Companion

Diameter Face Flange
Bore Keyway F-Female Hub to End Part

3

Diameter Width M-Male Figure Diameter of Hub Number

1610 SERIES (Continued) A-6.875 B-6.125 DIA. (8 HOLES)

2.500 .625 6.625 F 1 .375 D 5.250 3.500 5-1-873-6

2.750 .625 6.625 F 1 .375 D 5.250 3.500 5-1-873-7

2.938 .750 6.625 F 1 .375 D 5.250 3.500 5-1-873-8

3.000 .750 6.625 F 1 .375 D 5.250 3.500 5-1-873-9

3.125 — 6.625 F 2 .375-24 T 6.875 5.000 5-1-883

3.500 .875 6.625 F 2 .375-24 T 6.875 5.000 5-1-883-1

4

5

Footnotes for parts and assemblies that are discontinued, will be discontinued upon depletion of
stock, or not sold separately, are indicated by a symbol next to the part number. Match the symbol
to the appropriate status at the bottom of the page. All other footnotes are located immediately
below the yoke dimensional data.

Diameter
D-Drilled
T-Tapped

6

Bolt

Hole

7 8

Part

Number

Important Notice: The data listed herein is correct to the best of our knowledge and belief; having
been compiled from reliable and offi cial sources of information. However, WE CANNOT ASSUME
ANY RESPONSIBILITY for possible error.

Important: See Safety Information in General Information Section (J300P-GI)

3

COMPANION FLANGES

Spline Hole

J300P-1

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

1.010-15 Involute Spline

1.010 2.375-F 3.125 .375D 4 — 2.125 1.312 2.000 1 — — 2-1-2581

1.145-26 Involute Spline

1.145 2.750-M 3.750 .438-20T 4 — 1.547 1.500 2.109 2 — — 3-1-4371• 1350

1.146-26 Involute Spline

1.146 2.375-F 3.125 .375 D 4 2.438 1.547 1.500 2.062 1 — — 2-1-2391•

1.146 2.375-F 3.125 .375D 4 2.550 1.554 1.500 2.594 1 2-1-1881X 15099 2-1-1871• 1310

OEM only

1.229-28 Involute Spline

1.229 2.750-M 3.750 .438-20T 4 — 1.844 1.375 2.062 1 — — 2-1-2341 1330

1.250-10 Spline

1.250 2.375-F 3.125 .375D 4 2.500 1.750 2.000 2.688 1 — — 2-1-1641• 1310

1.250 2.750-M 3.750 .438D 4 — 2.000 1.750 2.312 1 — — 3-1-3851• 1350

1.250-21 Based On 24 Spline

1.250 2.559-M 4.250 .500 D 4 — 1.875 1.488 2.787 2 2006269 2002304 2006268

1.250 3.541-F 4.216 .400 D 4 — 1.875 1.488 4.000 2 2006270• 2002304 2006271

Spicer axle fl ange ; OEM only

Spicer axle fl ange

1.276-29 Involute Spline

1.276 2.750-F 3.750 .438D 4 — 1.875 1.500 2.062 1 3-1-4041X• 34592 3-1-4031 1350

3-1-4031 was replaced by 3-1-4041X

1.375-10 Spline

1.375 2.375-F 3.125 .375 T 4 — 2.063 1.750 2.555 1 — — 2-1-14029

1.375 2.375-F 3.125 .375D 4 2.500 2.125 1.156 2.125 1 — — 2-1-2091 1310

1.375 2.750-F 3.750 .375D 4 3.109 1.938 2.000 2.562 1 — — 3-1-1181• 1350/1410

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

4

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Spline Hole

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

1.375-10 Spline (Continued)

1.375 2.750-F 3.750 .438D 4 — 1.750 1.688 2.250 1 — — 3-1-3881•

1.375 2.750-F 3.750 .438D 4 — 2.125 1.062 1.656 1 — — 3-1-4141• 1350

1.375 2.750-F 3.750 .438D 4 3.000 2.125 2.000 2.438 1 — — 3-1-4001 1350/1410

1.375 2.750-F 3.750 .438D 4 3.000 1.938 2.062 2.570 1 — — 3-1-2931• 1350

1.375 2.750-F 3.750 .438D 4 3.000 2.125 2.000 2.438 1 — — 3-1-751 1350/1410

1.375 2.750-F 3.750 .438D 4 3.000 2.125 2.000 2.516 1 — — 3-1-2311 1350/1410

1.375 2.750-F 3.750 .438D 4 3.000 2.125 2.000 2.438 1 — — 3-1-2011 1350/1410

1.375 3.750-F 4.750 .500D 4 3.750 2.109 2.000 2.625 1 — — 4-1-3151•

1.401-32 Involute Spline

1.401 2.750-M 3.750 .438D 4 — 2.125 3.656 5.375 2 — — 3-1-4271 1350

.940 deep counterbore at hub end

1.499-10 Spline

1.499 2.750-F 3.750 .438D 4 3.000 2.242 2.000 2.562 1 — — 3-1-811• 1350

1.499 2.751-F 3.750 .438D 4 3.000 2.127 2.000 2.555 1 — — 3-1-2181• 1350

1.500-10 Spline

1.500 2.750-F 3.750 .438D 4 3.000 2.125 2.000 2.438 1 — — 3-1-2431 1350

1.500 2.750-F 3.750 .438D 4 3.112 2.250 2.188 3.062 2 — — 3-1-3341 1410

1.500 2.750-F 3.750 .438D 4 3.112 2.000 2.188 2.906 1 — — 3-1-3431 1350/1410

.310 deep counterbore at hub end

1.500 2.750-F 3.750 .438D 4 3.000 2.250 2.000 2.375 1 — — 3-1-3191 1350/1410

1.500 2.750-F 3.750 .438D 4 2.875 2.125 2.000 2.562 1 — — 3-1-1151 1350

1.500 2.750-F 3.750 .438D 4 — 2.250 2.062 2.750 1 — — 3-1-1141• 1350

1.500 3.125-M 3.969 .438T 4 — — 2.000 2.750 2 — — 2-1-2501 1330

Hub diameter not ground

1.500 3.750-F 4.750 .500D 4 3.750 2.125 2.000 2.625 1 — — 4-1-2701 1550

1.500 3.750-F 4.750 .500D 4 3.750 2.250 2.000 2.500 1 — — 4-1-3441 1480/1550

1.500 6.625-F 6.125 .375D 8 6.875 2.125 2.000 2.375 3 — — 5-1-2421• 1610

.250 deep counterbore at hub end

1.516-35 Involute Spline

1.516 2.750-F 3.750 .438D 4 2.875 2.125 2.000 2.562 1 — — 3-1-3651 1350/1410

1.520-23 Involute Spline

1.520 2.750-F 3.750 .438D 4 — 2.125 2.047 2.609 1 — — 3-1-3971 1410

1.525-35 Involute Spline

1.525 3.750-M 4.750 .500D 4 3.875 2.500 1.938 3.562 2 — — 4-1-4121• 1480/1550

1.543-24 Involute Spline

1.543 2.677-M 4.250 12MM D 4 — 2.241 1.840 3.907 2 3-1-4961X• 232686 3-1-4951

1.605-15 Involute Spline

1.605 3.125-M 3.960 .438T 0 — 2.125 1.932 3.141 2 — — 2-1-2511•

1.625-10 Spline

1.627 2.750-F 3.750 .438D 4 3.000 2.375 2.125 3.000 2 — — 3-1-3531•

1.625 3.750-F 4.750 .500D 4 — 2.375 2.125 2.750 1 — — 4-1-2751• 1480

1.625 3.750-M 4.750 .500D 4 — 2.250 2.125 2.688 1 — — 4-1-3571 1480

1.750-10 Spline

1.750 2.750-F 3.750 .438D 4 3.000 2.250 2.188 2.812 1 — — 3-1-3211 1350/1410

1.750 2.750-F 3.750 .438D 4 3.112 2.625 2.250 3.125 2 — — 3-1-1521 1410

1.750 3.750-F 4.750 .500D 4 3.750 2.500 2.250 3.000 1 — — 4-1-3891 1550

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

5

COMPANION FLANGES

Spline Hole

J300P-1

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

1.750-10 Spline (Continued)

1.750 3.750-F 4.750 .500D 4 — 2.500 1.938 2.734 1 — — 4-1-5131 1550

1.750 3.750-F 4.750 .500D 4 — 2.625 2.250 2.875 1 — — 4-1-3101 1480

1.750 3.750-F 4.750 .500D 4 — 2.500 2.250 2.875 1 4-1-3331X• 565W 4-1-3321• 1480

Slinger not sold separately

1.750 3.750-F 4.750 .500D 4 3.875 2.375 2.188 2.812 1 — — 4-1-3171 1480

1.750 3.750-F 4.750 .500D 4 3.750 2.250 2.000 2.750 1 — — 4-1-1381 1480

1.750 3.750-M 4.750 .500D 4 — 2.500 2.000 3.547 2 4-1-5211X — 4-1-7001 1550

4-1-7001 was replaced by 4-1-5211X

1.750 3.750-M 4.750 .500D 4 — 2.500 1.938 3.562 2 — — 4-1-3721 1480/1550

1.750 5.312-M 6.125 .375D 8 — 2.500 2.000 3.938 3 5-1-6541X• — 5-1-6531 1610

5-1-6531 was replaced by 5-1-6541X; Assembly includes eight 6-73-725 bolts

1.750 6.625-F 6.125 .375D 8 — 2.625 2.250 2.875 3 — — 5-1-811 1610

1.750 7.750-F 7.250 .375D 8 — 2.750 2.250 2.938 3 — — 6-1-1761 1710

1.755-13 Involute Spline

1.755 3.750-F 4.750 .509D 4 — — 2.825 3.760 1 — — 4-1-5341

Hub diameter not ground

1.755 6.625-F 6.125 .375D 8 — 3.062 2.915 3.625 3 — — 5-1-6511 1610

1.790-34 Involute Spline

1.790 .000-F 5.118 .512 D 4 — 2.625 2.188 2.590 1 — — 5-1-02709

Serrated face fl ange

1.790 .000-F 5.118 .512 D 4 — 2.625 2.188 2.590 1 — — 5002709

5002709 will be replaced by 5-1-02709 when supply is exhausted; Serrated face fl ange

1.790 3.750-F 4.750 .500D 4 — 2.562 2.750 3.344 1 4-1-4501X — 4-1-4491 1480/1550

Assembly includes plug 231059

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

6

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Spline Hole

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

1.790-34 Involute Spline (Continued)

1.790 3.750-M 4.750 .500D 4 — 2.562 2.750 3.344 1 4-1-5201X — 4-1-4471• 1480/1550

Assembly includes plug 231059 and four 8-73-226 bolts

1.790 3.750-M 4.750 .500D 4 — 2.562 2.750 3.344 1 4-1-4481X — 4-1-4471• 1480/1550

4-1-4481X was replaced by 4-1-5201X; Assembly includes plug 231059 and 4 studs 231016

1.790 5.312-M 6.125 .375D 8 — 2.562 2.750 3.719 3 90-1-21X — 90-1-11 SPL90

90-1-11 was replaced by 90-1-21X; Assembly includes plug 231059 and eight 6-73-725 bolts

1.790 5.312-M 6.125 .375D 8 — 2.562 2.750 4.250 3 5-1-5151X• — 5-1-5141• 1610

Assembly includes plug 231059 and eight 6-73-725 bolts

1.790 6.625-F 6.125 .375D 8 — 2.562 2.781 3.938 3 5-1-5121X — 5-1-5111 1610

5-1-5111 was replaced by 5-1-5121X; Assembly includes plug 231059

1.790 7.750-F 7.250 .375D 8 — 2.562 2.688 3.903 3 6-1-4701X — 6-1-4691 1710

6-1-4691 was replaced by 6-1-4701X; Assembly includes plug 231059

1.922-14 Involute Spline

1.922 3.750-F 4.750 .510D 4 — 2.375 2.183 3.312 2 — — 4-1-5451• 1550

1.922 6.625-F 6.125 .385D 8 — 2.375 2.183 2.840 3 — — 5-1-6891 1610

.120 deep counterbore at hub end

1.960-10 Spline

1.960 3.750-F 4.750 .500D 4 — 2.750 2.625 3.375 1 — — 4-1-2661• 1480

1.960 7.750-F — D 0 — 2.957 2.620 3.312 2 — — 6.5-1-271

1.960 7.750-F 7.250 .375D 8 — 2.750 2.625 3.312 3 — — 6-1-1461 1710

1.960 7.750-F 7.250 .375D 8 — 2.812 3.000 3.625 3 — — 6-1-4641 1710

1.961-6 Spline

1.961 3.750-F 4.750 .500D 4 — 2.750 3.000 3.625 1 — — 4-1-601•

1.962-10 Spline

1.962 5.312-M 6.125 .375D 8 — 2.750 2.797 4.594 3 5-1-6561X — 5-1-6551 1610

Assembly includes eight 6-73-725 bolts

1.962 6.625-F 6.125 .375D 8 — 2.500 2.625 3.250 3 — — 5-1-4301•

1.964-10 Spline

1.964 3.750-F 4.750 .500D 4 — 2.500 2.250 3.000 1 — — 4-1-3761• 1480

1.964 3.750-M 4.750 .500D 4 — 2.938 3.031 3.625 1 — — 4-1-4421• 1480

1.964 6.625-F 6.125 .375D 8 — 2.500 2.250 3.000 3 — — 5-1-4291•

1.998-38 Involute Spline

1.998 3.750-F 4.750 .500D 4 — 2.750 2.125 2.875 1 — — 4-1-5021 1480/1550

1.998 3.750-M 4.750 .500D 4 — 2.750 2.062 3.875 1 4-1-6051X — 4-1-6041 1550

Assembly includes four 8-73-226 studs

1.998 5.312-M 6.125 .375D 8 — 2.750 2.125 4.688 3 5-1-6471X — 5-1-6271 1610

5-1-6271 was replaced by 5-1-6471X; Assembly includes eight 6-73-725 bolts

1.998 6.436-M 7.250 .375D 8 — 2.750 2.141 4.703 3 6-1-5851X — 6-1-5781 1710

6-1-5781 was replaced by 6-1-5851X; Assembly includes eight 6-73-725 bolts

2.000-10 Spline

2.000 3.750-F 4.750 .500D 4 3.750 2.750 3.000 3.625 1 — — 4-1-3781• 1480

2.000 3.750-F 4.750 .500D 4 — 2.938 3.000 3.625 1 — — 4-1-2361 1480

2.000 6.625-F 6.125 .375D 8 — 2.938 3.000 3.625 3 — — 5-1-3161 1610

2.000 6.625-F 6.125 .375D 8 — 3.250 3.000 3.625 3 — — 5-1-931• 1610

2.000 6.625-F 6.125 .375D 8 — 2.750 3.000 3.625 3 — — 5-1-3141 1610

2.000 7.750-F 7.250 .375D 8 — 2.750 3.000 3.688 3 — — 6-1-2221 1710

2.000 7.750-F 7.250 .375D 8 — 3.250 3.125 3.812 3 — — 6-1-911• 1710

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

7

COMPANION FLANGES

Spline Hole

J300P-1

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

2.032-10 Spline

2.032 7.750-F 7.250 .438D 12 — 2.750 2.000 2.688 4 — — 6.5-1-2421• 1810

2.114-32 Involute Spline

2.114 .000-F 5.118 .512 D 4 — 3.000 2.250 3.500 1 — — 5002710

5002710 will be replaced by 5-1-02710 when supply is exhausted; Serrated face fl ange

2.114 .000-F 5.118 .512 D 4 — 3.000 2.250 3.500 1 — — 5-1-02710

Serrated face fl ange

2.114 5.312-M 6.125 .385D 8 — 3.000 2.250 2.844 3 5-1-6731X• 232200 5-1-6721 1610

.424 deep counterbore at hub end

2.114 6.625-F 6.125 .375D 8 — 3.000 2.245 2.844 3 5-1-6701X• 232200 5-1-6691• 1610

.424 deep counterbore at hub end

2.143-41 Involute Spline

2.143 7.750-F 7.250 .440D 12 — 2.939 2.495 3.500 4 — — 6.5-1-2941 1810

2.149-16 Spline

2.149 6.625-F 6.125 .385D 8 — 2.938 3.000 3.750 3 — — 5-1-2551• 1610

.380 deep counterbore at hub end

2.225-6 Spline

2.225 6.625-F 6.125 .375D 8 — 3.000 3.250 3.875 3 — — 5-1-2541 1610

2.225 7.750-F 7.250 .375D 8 — 3.000 3.250 3.750 3 — — 6-1-1731 1710

2.225 7.750-F 7.250 .375D 8 — 3.000 3.250 4.469 3 — — 6-1-1481• 1710

2.225 7.750-F 7.250 .438D 12 — 3.000 3.250 3.750 4 — — 6.5-1-481 1810

2.250-10 Spline

2.250 6.625-F 6.125 .375D 8 — 3.500 3.000 3.625 3 — — 5-1-6331 1610

2.250 7.750-F 7.250 .375D 8 — 3.000 3.000 3.750 3 — — 6-1-1421 1710

.250 deep counterbore at hub end

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

8

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Spline Hole

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

2.250-10 Spline (Continued)

2.250 7.750-F 7.250 .375D 8 — 3.500 3.000 3.688 3 — — 6-1-951 1710

2.250 7.750-F 7.250 .438D 12 — 3.500 3.000 3.688 4 — — 6.5-1-151 1810

2.250 7.750-F 7.250 .438D 12 — 3.000 3.000 3.750 4 — — 6.5-1-211 1810

.250 deep counterbore at hub end

2.274-44 Involute Spline

2.274 7.750-F 7.250 .438D 12 — 2.938 2.500 3.094 4 6.5-1-2401X 231022 6.5-1-2391 1810

6.5-1-2391 was replaced by 6.5-1-2401X

2.350-16 Spline

2.350 7.750-F 7.250 .375D 8 — 3.312 2.750 3.438 3 — — 6-1-5581 1710

For use on coupling shaft

2.350 7.750-F 7.250 .438D 12 — 3.317 2.750 3.438 4 — — 6.5-1-1811 1810

For use on coupling shaft

2.351-16 Spline

2.351 7.750-F 7.250 .375D 8 — 3.750 2.750 3.000 3 — — 6-1-4571• 1710

Hub machined for speedometer gear and no.3 woodruff keyway

2.364-18 Involute Spline

2.364 7.750-F 7.250 .375D 8 6.656 3.500 3.375 4.031 3 — — 6-1-4541 1710

2.364 7.750-F 7.250 .438D 12 — 2.750 2.328 3.000 4 — — 6.5-1-2301•

2.364 7.750-F 7.250 .438D 12 — 3.500 3.375 4.031 4 — — 6.5-1-1801 1810

2.374-46 Involute Spline

2.374 7.750-F 7.250 .438D 12 — 3.750 2.391 3.109 4 — — 6.5-1-2441• 1810

Hub machined for speedometer gear

2.374 7.750-F 7.250 .438D 12 — 3.500 2.391 6.625 4 — — 6.5-1-2591•

Special Mack fl ange, 4 additional counterbore .312 dia holes

2.390-46 Involute Spline

2.390 7.750-F 7.250 .375D 8 — 3.500 3.375 4.547 3 — — 6-1-4671 1710

2.422-18 Involute Spline

2.422 7.750-F 7.250 .378D 8 — 3.375 3.000 3.690 3 6-1-5601X 231013 6-1-5591 1710

2.447-28 Involute Spline

2.447 7.750-F 7.250 .378D 8 — 3.375 2.495 3.570 3 — — 6-1-6161• 1710

2.500-10 Spline

2.500 6.500-F — — 12 — 3.500 3.000 3.688 2 — — 6.5-1-3041

2.500 7.750-F 7.250 .375D 8 — 3.250 3.000 3.688 3 — — 6-1-4481 1710

2.500 7.750-F 7.250 .375D 8 — 3.750 3.000 3.625 3 6-1-5651X 231616 6-1-5541 1710

6-1-5541 was replaced by 6-1-5651X

2.500 7.750-F 7.250 .378D 8 — 3.500 2.405 3.310 3 6-1-6081X• 232042-10 6-1-6071 1710

2.500 7.750-F 7.250 .378D 8 — 3.250 3.000 3.620 3 — — 6-1-5741 1710

.880 deep counterbore at hub end

2.500 7.750-F 7.250 .438D 12 — 3.750 3.000 3.625 4 6.5-1-2351X• 231616 6.5-1-2271 1810

6.5-1-2271 was replaced by 6.5-1-2351X

2.500 7.750-F 7.250 .440D 12 — 3.500 2.410 3.310 4 — — 6.5-1-2041 1810

2.500-19 Involute Spline

2.500 6.438-F — — 8 — 3.500 4.000 5.500 2 8-1-131X — 8-1-121•

includes eight 10-73-109 bolts

2.503-19 Involute Spline

2.503 7.000-F 8.250 .625-18T 8 — 3.500 4.000 5.500 5 — — 8-1-191• 1850

2.503 7.750-F 7.250 .438D 12 6.625 3.500 3.000 3.844 4 — — 6.5-1-1361

.250 deep counterbore at hub end

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

9

COMPANION FLANGES

Spline Hole

J300P-1

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

2.541-19 Involute Spline

2.541 7.750-F 7.250 .440D 12 — 3.125 2.825 4.590 2 — — 6.5-1-3001

2.544-49 Involute Spline

2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 131436K• 5008437 6-1-6281 1710

Nut #131095 (incl. in assy) is used only on Spicer Axles.

Slinger not sold separately

2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 131436K• 5008437 5008460•

Nut #131095 (incl. in assy) is used only on Spicer Axles.

Slinger not sold separately

2.544 7.750-F 7.250 .375D 8 — 3.818 2.125 3.130 1 5008460• 5008437 6-1-6281 1710

2.560-20 Involute Spline

2.560 7.750-F 7.250 .438D 12 6.625 3.500 3.344 4.000 4 — — 6.5-1-2161 1810

2.625-25 Involute Spline

2.625 7.750-F 7.250 .375D 8 — 3.500 3.016 3.625 3 — — 6-1-5511 1710

2.635-20 Involute Spline

2.635 6.992-M 8.250 .625T 8 — 4.004 3.305 4.442 5 8-1-821X• 230888 8-1-811

.560 deep counterbore at hub end

Slinger not sold separately

2.750-10 Spline

2.750 6.625-F 6.125 .375D 8 — 3.750 3.000 4.060 3 5-1-6611X• 231616 5-1-6601

2.750 7.750-F 7.250 .438D 12 — 4.000 2.938 3.750 4 — — 6.5-1-1871 1810

Hub machined for speedometer gear

2.750 7.750-F 7.250 .438D 12 — 3.500 3.000 4.062 4 — — 6.5-1-741 1810

2.750 7.750-F 7.250 .438D 12 — 3.750 3.000 4.062 4 6.5-1-2361X 231616 6.5-1-2311• 1810

2.750 8.000-M 7.250 .375D 8 8.000 3.500 3.000 3.688 3 — — 6-1-2381 1710

Use with thru stop brake disc. mount between fl ange & yoke

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

10

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Spline Hole

D C B Bolt Hole E F G Companion
Spline Pilot Brake Flange Flange Companion

Hole Diameter Bolt Diameter Drum Ground Length Face Assembly Slinger Flange
Major F-Female Circle D-Drilled # of Pilot Hub Thru to End (includes slinger Part Part Series
Diameter M-Male Diameter T-Tapped Holes Diameter Diameter Hole of Hub when listed) Number Number

F

i

g
u

r

e

2.784-21 Involute Spline

2.784 6.438-M 7.250 .438D 16 — 3.500 3.000 4.125 6 — — 6-1-5231• 1710

Part has 16 equally spaced holes

2.784 7.750-F 7.250 D 12 — 3.375 3.125 4.440 1 — — 6.5-1-3021

3.000-10 Spline

3.000 7.750-F 7.250 .440D 12 — 4.000 3.062 3.750 4 — — 6.5-1-951

3.503-27 Involute Spline

3.503 6.888-M 11.024 .875D 8 — 5.003 4.185 5.850 2 315DIN-1-71X• 231574 315DIN-1-61 315 DIN

Slinger not sold separately

3.503 7.000-F 8.250 .625D 8 — 5.005 4.000 5.188 5 8-1-791X 230922 8-1-751 1880

Slinger not sold separately

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

11

Circular Type - Straight Round Hole

COMPANION FLANGES

Figure 1 Figure 2

J300P-1

D K C E F
Pilot Flange Companion

Diameter Face Flange
Bore Keyway F-Female Hub to End Part
Diameter Width M-Male Figure Diameter of Hub Number

Bolt

Hole
Diameter
D-Drilled
T-Tapped

1310 SERIES A-3.875 B-3.125 DIA. (4 HOLES)

.750 — 2.375-F 1 .375-D 2.438 2.000 2-1-1313

Rough bore - without keyway

1.000 .250 2.375-F 1 .375-D 2.438 2.000 2-1-1313-1

1.250 .250 2.375-F 1 .375-D 2.438 2.000 2-1-1313-3

1.250 .310 2.375-M 1 —-D 2.250 2.000 2-1-1353-5

1.250 .312 2.375-F 1 .375-D 2.438 2.000 2-1-1313-4

1.375 .312 2.375-F 1 .375-D 2.438 2.000 2-1-1313-5

1.438 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-7

1.500 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-8

1.625 .375 2.375-F 1 .375-D 2.438 2.000 2-1-1313-9

1.750 .375 2.375-F 2 .375-24-T 3.875 2.500 2-1-1323-1

1.875 .500 2.375-F 2 .375-24-T 3.875 2.500 2-1-1323-3

1350 SERIES A-4.562 B-3.750 DIA. (4 HOLES)

1.000 — 2.750-F 1 .438-D 2.875 2.000 3-1-1013

Rough bore - without keyway

1.000 — 2.750-F 1 .440-D 2.875 3.440 3-1-303

Rough bore - without keyway

1.000 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-1

1.125 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-2

1.250 .250 2.750-F 1 .438-D 2.875 2.000 3-1-1013-3

1.250 .312 2.750-F 1 .438-D 2.875 2.000 3-1-1013-4

1.375 .312 2.750-F 1 .438-D 2.875 2.000 3-1-1013-5

1.375 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-6

1.438 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-7

1.500 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-8

1.625 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-9

1.750 — 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023•

Rough bore - without keyway

1.750 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-10

1.750 .377 2.750-F 1 .440-D 2.875 3.440 3-1-303-7

1.875 .375 2.750-F 1 .438-D 2.875 2.000 3-1-1013-11

1.875 .500 2.750-F 1 .438-D 2.875 2.000 3-1-1013-12

2.000 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-1

2.125 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-2

2.250 .500 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-10•

12

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Circular Type - Straight Round Hole

D K C E F
Pilot Flange Companion

Diameter Face Flange
Bore Keyway F-Female Hub to End Part
Diameter Width M-Male Figure Diameter of Hub Number

Bolt

Hole
Diameter
D-Drilled

T-Tapped

1350 SERIES (Continued) A-4.562 B-3.750 DIA. (4 HOLES)

2.250 .625 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-3

2.375 .625 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-4•

2.750 .625 2.750-F 2 .438-20-T 4.562 3.000 3-1-1023-7•

1480 SERIES A-5.875 B-4.750 DIA. (4 HOLES)

1.250 — 3.750-F 1 .500-D 3.750 2.500 4-1-1133

Rough bore - without keyway

1.500 .375 3.750-F 1 .500-D 3.750 2.500 4-1-1133-1

1.625 .375 3.750-F 1 .500-D 3.750 2.500 4-1-1133-2

1.750 .375 3.750-F 1 .500-D 3.750 2.500 4-1-1133-3

1.875 .500 3.750-F 1 .500-D 3.750 2.500 4-1-1133-5

2.000 .500 3.750-F 1 .500-D 3.750 2.500 4-1-1133-6

2.250 .500 3.750-F 1 .500-D 3.750 2.500 4-1-1133-13

2.250 .625 3.750-F 1 .500-D 3.750 2.500 4-1-1133-8

2.375 — 3.750-F 2 .500-20-T 5.875 3.000 4-1-1143

Rough bore - without keyway

2.375 .625 3.750-F 1 .500-D 3.750 2.500 4-1-1133-9•

2.500 .625 3.750-F 2 .500-20-T 5.875 3.000 4-1-1143-1

2.938 .750 3.750-F 2 .500-20-T 5.875 3.000 4-1-1143-3•

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

13

COMPANION FLANGES

Circular Type - Straight Round Hole

J300P-1

D K C
Pilot Diameter Diameter Flange Face Flange

Bore Keyway F-Female D-Drilled Hub to End Part
Diameter Width M-Male Figure T-Tapped Diameter of Hub Number

Bolt Hole

E F

Companion

1610 SERIES A-6.875 B-6.125 DIA. (8 HOLES)

1.250 — 6.625-F 1 .375-D 5.250 3.500 5-1-873

Rough bore - without keyway

2.000 .500 6.625-F 1 .375-D 5.250 3.500 5-1-873-1

2.250 .625 6.625-F 1 .375-D 5.250 3.500 5-1-873-3

2.750 .625 6.625-F 1 .375-D 5.250 3.500 5-1-873-7

2.938 .750 6.625-F 1 .375-D 5.250 3.500 5-1-873-8•

3.000 .750 6.625-F 1 .375-D 5.250 3.500 5-1-873-9

3.125 — 6.625-F 4 .375-24-T 6.875 5.000 5-1-883

Rough bore - without keyway

3.500 .875 6.625-F 4 .375-24-T 6.875 5.000 5-1-883-1

1710 SERIES A-8.000 B-7.250 DIA. (8 HOLES)

1.250 — 7.750-F 1 .375-D 6.375 4.000 6-1-1253

Rough bore - without keyway

2.438 .625 7.750-F 1 .375-D 6.375 4.000 6-1-1253-1

2.750 .625 7.750-F 1 .375-D 6.375 4.000 6-1-1253-3

2.938 .750 7.750-F 1 .375-D 6.375 4.000 6-1-1253-4

3.500 .875 7.750-F 1 .375-D 6.375 4.000 6-1-1253-6

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

14

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Circular Type - Straight Round Hole

D K C E F
Pilot Flange Companion

Diameter Face Flange
Bore Keyway F-Female Hub to End Part
Diameter Width M-Male Figure Diameter of Hub Number

Bolt

Hole

Diameter

D-Drilled

T-Tapped

1810 SERIES A-8.000 B-7.250 DIA. (12 HOLES)

1.250 — 7.750-F 3 .438-D 6.375 4.000 6.5-1-533

Rough bore - without keyway

2.438 .625 7.750-F 3 .438-D 6.375 4.000 6.5-1-533-1•

2.500 .625 7.750-F 3 .438-D 6.375 4.000 6.5-1-533-2

2.938 .750 7.750-F 3 .438-D 6.375 4.000 6.5-1-533-4

3.500 .875 7.750-F 3 .438-D 6.375 4.000 6.5-1-533-6

1880 SERIES A-9.500 B-8.250 DIA. (8 HOLES)

1.500 — 7.000-F 2 .625-D 6.875 5.000 9-1-333

2.938 .750 7.000-F 2 .625-D 6.875 5.000 9-1-333-2

3.500 .875 7.000-F 2 .628-D 6.875 5.000 9-1-333-4•

4.000 1.000 7.000-F 1 .625-D 6.875 5.000 9-1-333-6

Rough bore - without keyway

Has two threaded set screw holes

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

15

COMPANION FLANGES

Rectangular Type—Straight Round Hole

J300P-1

D K C E F G
Pilot Flange Companion
Diameter Length Face Flange
Bore Keyway F-Female Hole Hub Thru to End Part
Diameter Width M-Male Diameter At Diameter Hole of Hub Number

Set Screw Hole

Viewed from Hub

End & Keyway at 12

1100 SERIES A-3.500 B-2.750 DIA. (4 HOLES)

.875 .188 2.250-F .375 6 1.875 1.500 2.125 1-1-253
.875 .250 2.250-F .375 6 1.875 1.500 2.125 1-1-293•

1.000 .250 2.250-F .375 6 1.875 1.500 2.125 1-1-143

1.125 .250 2.250-F .375 6&9 1.875 1.500 2.125 1-1-153

1.125 .312 2.250-F .375 6 1.875 1.500 2.125 1-1-123

1.250 .312 2.250-F .375 6 1.875 1.500 2.125 1-1-273

1.250 .312 2.250-F .375 3 1.875 1.500 2.125 1-1-653

1.375 .312 2.250-F .375 6 2.125 1.500 2.125 1-1-473

1310 SERIES A-3.875 B-3.125 DIA. (4 HOLES)

.875 .188 2.375-F .375 6 1.875 1.500 2.062 2-1-623•

1.000 .250 2.375-F .375 6 1.875 1.500 2.062 2-1-283

1.125 .250 2.375-F .375 6&9 1.875 1.500 2.062 2-1-293

1.125 .312 2.375-F .375 6 1.875 1.500 2.062 2-1-303•

1.250 .250 2.375-F .375 6 1.875 1.500 2.062 2-1-323

1.250 .312 2.375-F .375 6 1.875 1.500 2.062 2-1-333

1.375 .312 2.375-F .375 6 2.120 1.500 2.062 2-1-903

Hub diameter not ground

1.500 .375 2.375-F .375 6 2.438 2.000 2.625 2-1-933

1350 SERIES A-4.562 B-3.750 DIA. (4 HOLES)

1.250 .312 2.750-F .375 6 2.250 2.000 2.562 3-1-163

1.500 .375 2.750-F — — 2.250 2.000 2.562 3-1-333

1.750 .375 2.750-F .375 12 2.812 — 3.438 3-1-463

3-1-463 was replaced by 3-1-303-7

1480 SERIES A-5.875 B-4.750 DIA. (4 HOLES)

2.000 .375 3.750-F — — 3.000 2.750 3.590 4-1-1123•

Hub diameter not ground

1550 SERIES A-5.750 B-4.750 DIA. (4 HOLES)

1.250 — 3.750-F — — 3.000 3.062 3.625 4-1-543

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

16

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

COMPANION FLANGES

Circular Type—Taper Hole

C D - Taper Hole E F G
Pilot Flange Brake Companion

Diameter Width Ground Length Face Drum Flange
M-Male Bore of Hub Thru to End Pilot Part
F-Female Diameter Keyway Diameter Hole of Hub Diameter Number

1610 SERIES A-6.875 B-6.125 DIA. (8 HOLES)

6.625-F 1.750 .438 2.750 2.250 2.938 — 5-1-1154

6.625-F 2.000 .500 3.250 3.000 3.625 — 5-1-1924

1650/1710 SERIES A-CIRCULAR 8.000 B-7.250 DIA. (8 HOLES .325 DIA)

7.750-F 2.000 .500 3.250 3.000 3.688 — 6-1-1144

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

Important: See Safety Information in General Information Section (J300P-GI)

17

COMPANION FLANGE

J300P-1

Rectangular Type—Taper Hole

C D - Taper Hole E F G
Pilot Flange Brake Companion

Diameter Width Ground Length Face Drum Flange
M-Male Bore of Hub Thru to End Pilot Part
F-Female Diameter Keyway Diameter Hole of Hub Diameter Number

1310 SERIES A-3.875 B-3.125 DIA. (4 HOLES)

1.375 Spline

2.375-F 1.375 .375 2.250 2.000 2.625 — 2-1-634

1.500 Spline

2.375-F 1.500 .375 2.375 2.000 2.625 — 2-1-684•

1350/1 SERIES A=4.625 B=3.750 (4 HOLES)

1.250 Spline

2.750-F 1.250 .312 2.125 1.500 2.437 3.000 3-1-604

1.375 Spline

2.750-F 1.375 .375 2.250 2.000 2.625 — 3-1-584

• Part is discontinued  Part is available until supply is exhausted  Not sold separately

18

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

PART NUMBER INDEX

1-1-123 ............................16

1-1-143 ............................16

1-1-153 ............................16

1-1-253 .......................16

1-1-273 ............................16

1-1-293• ...........................16

1-1-473 .......................16

1-1-653 .......................16

2-1-283 ............................16

2-1-293 ............................16

2-1-303• ...........................16

2-1-323 ............................16

2-1-333 ............................16

2-1-623• ...........................16

2-1-634 .............................18

2-1-684• ............................18

2-1-903 .......................16

2-1-933 ............................16

2-1-1313 ..........................12

2-1-1313-1 .......................12

2-1-1313-3 .......................12

2-1-1313-4 .......................12

2-1-1313-5 .......................12

2-1-1313-7 .......................12

2-1-1313-8 .......................12

2-1-1313-9 .......................12

2-1-1323-1 .......................12

2-1-1323-3 .......................12

2-1-1353-5 .......................12

2-1-1641• ............................4

2-1-1871• ............................4

2-1-1881X ...........................4

2-1-2091 ..........................4

2-1-2341 ..........................4

2-1-2391• ............................4

2-1-2501 ..........................5

2-1-2511• ............................5

2-1-2581 .............................4

2-1-14029 ...........................4

3-1-163 ............................16

3-1-303 ............................12

3-1-303-7 .........................12

3-1-333 ............................16

3-1-463 ............................16

3-1-584 ..........................18

3-1-604 .............................18

3-1-751 ...............................5

3-1-811• ..............................5

3-1-1013 ..........................12

3-1-1013-1 .......................12

3-1-1013-2 .......................12

3-1-1013-3 .......................12

3-1-1013-4 .......................12

3-1-1013-5 .......................12

3-1-1013-6 .......................12

3-1-1013-7 .......................12

3-1-1013-8 .......................12

3-1-1013-9 .......................12

3-1-1013-10 .....................12

3-1-1013-11 .....................12

3-1-1013-12 .....................12

3-1-1023• .........................12

3-1-1023-1 .......................12

3-1-1023-2 .......................12

3-1-1023-3 .......................13

3-1-1023-4• ......................13

3-1-1023-7• ......................13

3-1-1023-10• ....................12

3-1-1141• ............................5

3-1-1151 .............................5

3-1-1181• ............................4

3-1-1521 .............................5

3-1-2011 .............................5

3-1-2181• ............................5

3-1-2311 ..........................5

3-1-2431 .............................5

3-1-2931• ............................5

3-1-3191 .............................5

3-1-3211 .............................5

3-1-3341 .............................5

3-1-3431 .............................5

3-1-3531• ............................5

3-1-3651 ..........................5

3-1-3851• ............................4

3-1-3881• ............................5

3-1-3971 .............................5

3-1-4001 ..........................5

3-1-4031 .............................4

3-1-4041X•..........................4

3-1-4141• ............................5

3-1-4271 ..........................5

3-1-4371• ............................4

3-1-4951 .........................5

3-1-4961X•..........................5

4-1-543 .......................16

4-1-601• ..............................7

4-1-1123• .........................16

4-1-1133 ..........................13

4-1-1133-1 .......................13

4-1-1133-2 .......................13

4-1-1133-3 .......................13

4-1-1133-5 .......................13

4-1-1133-6 .......................13

4-1-1133-8 .......................13

4-1-1133-9• ......................13

4-1-1133-13 .....................13

4-1-1143 ..........................13

4-1-1143-1 .......................13

4-1-1143-3• ......................13

4-1-1381 ..........................6

4-1-2361 .............................7

4-1-2661• ............................7

4-1-2701 .............................5

4-1-2751• ............................5

4-1-3101 .............................6

4-1-3151• ............................5

4-1-3171 ..........................6

4-1-3321• ............................6

4-1-3331X•..........................6

4-1-3441 ..........................5

4-1-3571 ..........................5

4-1-3721 ..........................6

4-1-3761• ............................7

4-1-3781• ............................7

4-1-3891 .............................5

4-1-4121• ............................5

4-1-4421• ............................7

4-1-4471• ............................7

4-1-4471• ............................7

4-1-4481X ...........................7

4-1-4491 .........................6

4-1-4501X ...........................6

4-1-5021 ..........................7

4-1-5131 .............................6

4-1-5201X ...........................7

4-1-5211X ........................6

4-1-5341 .............................6

4-1-5451• ............................7

4-1-6041 .........................7

4-1-6051X .......................7

4-1-7001 .............................6

5-1-811 ............................6

5-1-873 ............................14

5-1-873-1 .........................14

5-1-873-3 .........................14

5-1-873-7 .........................14

5-1-873-8• ........................14

5-1-873-9 .........................14

5-1-883 ............................14

5-1-883-1 .........................14

5-1-931• ..............................7

5-1-1154 ...........................17

5-1-1924 ..........................17

5-1-2421• ............................5

5-1-2541 .............................8

5-1-2551• ............................8

5-1-02709 ...........................6

5-1-02710 ...........................8

5-1-3141 ..........................7

5-1-3161 .............................7

5-1-4291• ............................7

5-1-4301• ............................7

5-1-5111 ..............................7

5-1-5121X .......................7

5-1-5141• ............................7

5-1-5151X•..........................7

5-1-6271 .............................7

5-1-6331 ..........................8

5-1-6471X ...........................7

5-1-6511 .............................6

5-1-6531 .............................6

5-1-6541X•..........................6

5-1-6551 .........................7

5-1-6561X ...........................7

5-1-6601 .......................10

5-1-6611X• ........................10

5-1-6691• ............................8

5-1-6701X•..........................8

5-1-6721 .........................8

5-1-6731X•..........................8

5-1-6891 ..........................7

6-1-911• ..............................7

6-1-951 ...............................9

6-1-1144 .....................17

6-1-1253 ..........................14

6-1-1253-1 .......................14

6-1-1253-3 .......................14

6-1-1253-4 .......................14

6-1-1253-6 .......................14

6-1-1421 ..........................8

6-1-1461 ..........................7

6-1-1481• ............................8

6-1-1731 .............................8

6-1-1761 ..........................6

6-1-2221 .............................7

6-1-2381 ........................10

6-1-4481 .............................9

6-1-4541 .............................9

6-1-4571• ............................9

6-1-4641 ..........................7

Important: See Safety Information in General Information Section (J300P-GI)

19

PART NUMBER INDEX

J300P-1

6-1-4671 ..........................9

6-1-4691 .............................7

6-1-4701X ...........................7

6-1-5231• ..........................11

6-1-5511 ...........................10

6-1-5541 .............................9

6-1-5581 .............................9

6-1-5591 .........................9

6-1-5601X ...........................9

6-1-5651X .......................9

6-1-5741 .............................9

6-1-5781 .............................7

6-1-5851X .......................7

6-1-6071 .........................9

6-1-6081X•..........................9

6-1-6161• ............................9

6-1-6281 .......................10

6-1-6281 .......................10

6.5-1-151 .........................9

6.5-1-211 .........................9

6.5-1-271 ............................7

6.5-1-481 ............................8

6.5-1-533 .........................15

6.5-1-533-1• .....................15

6.5-1-533-2 ......................15

6.5-1-533-4 ......................15

6.5-1-533-6 ......................15

6.5-1-741 ..........................10

6.5-1-951 ..........................1 1

6.5-1-1361 ..........................9

6.5-1-1801 ..........................9

6.5-1-1811 ..........................9

6.5-1-1871 .....................10

6.5-1-2041 ..........................9

6.5-1-2161 ........................10

6.5-1-2271 ..........................9

6.5-1-2301• .........................9

6.5-1-2311• .......................10

6.5-1-2351X•.......................9

6.5-1-2361X ......................10

6.5-1-2391 ..........................9

6.5-1-2401X ........................9

6.5-1-2421• .........................8

6.5-1-2441• .........................9

6.5-1-2591• .........................9

6.5-1-2941 .......................8

6.5-1-3001 .....................10

6.5-1-3021 .....................11

6.5-1-3041 ..........................9

8-1-121• ..............................9

8-1-131X .............................9

8-1-191• ..............................9

8-1-751 .........................11

8-1-791X ...........................11

8-1-811..........................10

8-1-821X•..........................10

9-1-333 ............................15

9-1-333-2 .........................15

9-1-333-4• ........................15

9-1-333-6 .........................15

90-1-11 ...............................7

90-1-21X .........................7

2006268 ..........................4

2006269 ..............................4

2006270 ..............................4

2006271 ..............................4

5002709 ..............................6

5002710 ..............................8

5008460• ..........................10

5008460• ..........................10

131436K• ..........................10

131436K• ..........................10

315DIN-1-61 .................11

315DIN-1-71X• .................11

20

Important: See Safety Information in General Information Section (J300P-GI)

J300P-1

NOTES

21

NOTES

J300P-1

22

J300P-1

NOTES

23

Dana Aftermarket Group

PO Box 1000
Maumee, Ohio 43537

Warehouse Distributors: 1.800.621.8084
OE Dealers: 1.877.777.5360

www.SpicerParts.com

J300P-1 Printed in U.S.A.
Copyright Dana Limited, 2014.
All rights reserved. Dana Limited.