Page 1
Spicer®10 Series
Driveshafts
The codes in this section are for quick reference to:
™
© 2005 Dana Corporation
J = Major spline diameter and number of spline teeth
S = Total slip
FF-FF = Flange face to flange face
CL-CL= Centerline to centerline
.
.S
S
= Shipping str
ß = Slip Joint max working angle (degrees)
Tight Joint max working angle (degrees)
θ =
T = Tube Length
R = Center line of center bearing to center line of end yoke/flange face
M = Center
line to Flange F
ap
ace
1
10 Series
Page 2
Short Coupled Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
2
10 Series
Page 3
Short Coupled Assembly
d Parts
Standar
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.375" - (34.9mm) - 16 Spline S = .938" - (23.8 mm)
9.07” 6.32” 2-2-329 5-477X 2-3-348KX 2-82-21 5-477X 2-2-329 920750-1
(230.3mm)
J = 1.375" - (34.9mm) - 16 Spline S = 1.125" - (28.5 mm)
8.38”
(212.8mm) (142.7mm)
C
-
L
L
(160.5
mm)
5.62” 2-2-329 5-255X 2-3-348KX 2-82-641 5-255X 2-2-329 207070-1
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1310
© 2005 Dana Corporation
3
10 Series
Page 4
Tube Type Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
θ
4
10 Series
Page 5
Tube Type Assembly
Standard Tube Size 2.5"x.083" (63.5mm x 2.11mm)
Tube Part Number 20-30-22
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.375" - (34.9mm) - 16 Spline S = 2.125" - (53.9mm)
Tubing Formula: T = FF-FF (Collapsed) minus 9.560" - (242.8mm)
10.78” 9.44” 2-2-329 5-477X 2-3-128KX 2-40-1041 2-28-277 5-477X S.S. 909250 (1)
(273.8mm) (239.7mm)
J = 1.375" - (34.9mm)- 16 Spline S = 3.062" - (77.7mm)
Tubing Formula: T = C
C
-
L
L
L-CL
10.91” S.S. 5-477X 2-3-8001KX 2-40-1711 2-28-367 5-477X S.S. 909426
(277.1
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(Collapsed) minus 9.690" - (246.1mm)
mm)
Series 1310
Tubing Formula: T = FF-FF (Collapsed) minus 11.310" - (287.2mm)
12.48” 10.86” S.S. 5-477X 2-3-8001KX 2-40-1711 2-28-367 5-477X 2-2-459 915754
(316.9mm) (275.8mm)
Tubing Formula: T = FF-FF (Collapsed) minus 12.440" - (315.9mm)
13.62” 10.86” 2-2-329 5-477X 2-3-8001KX 2-40-1711 2-28-367 5-477X 2-2-329 917814
mm) (275.8mm)
(345.9
(1) Non-Standard tube size 2.5" x 0.065" (63.5mm x 1.52mm) Part #20-30-12
© 2005 Dana Corporation
5
10 Series
Page 6
Short Coupled Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
6
10 Series
Page 7
Short Coupled Assembly
Series 1350
Minimum Length
Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.500" - (38.1mm) - 16 Spline S = .750" - (19.0mm)
9.50” 6.38" 3-2-119 5-480X 3-3-388KX 3-82-61 5-480X 3-2-119 9012-SF
(241.3
mm) (162.0mm)
L-CL
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
© 2005 Dana Corporation
7
10 Series
Page 8
Tube Type Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
θ
8
10 Series
Page 9
Tube Type Assembly
d Tube Size 3.0" x 0.083 (76.2mm x 2.11mm)
Standar
ube Part Number 24-30-42
T
Series 1350
Minimum Length
Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.500" - (38.1mm) - 16 Spline S = 2.000" - (50.8mm)
Tubing Formula: T = C
J = 1.500" - (38.1mm) - 16 Spline S = 3.624" - (92.0mm)
Tubing Formula: T = C
15.12" 12.00" 3-2-119 5-480X 3-3-488KX 3-40-1611 3-28-57 5-480X 3-2-119 909048
(384.0mm) (304.8mm)
L-CL
10.12" S.S 5-178X 3-3-598KX 3-40-1471 3-28-47 5-178X S.S. 910598 (1)
(257.0
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(Collapsed) minus 8.750" - (222.2mm)
L-CL
mm)
(Collapsed) minus 13.590" - (345.1mm) Minimum T = 1.470" - (37.3mm)
L-CL
(1) Non-Standard tube size 2.5" x 0.083" (63.5 mm x 2.11 mm) Part #20-30-22
© 2005 Dana Corporation
9
10 Series
Page 10
Short Coupled Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
10
10 Series
Page 11
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.500" - (38.1mm) - 16 Spline S = .750" - (19.0mm)
9.50” 6.12" 3-2-159 5-481X 3-3-468KX 3-82-81 5-481X 3-2-159 8134-SF
(241.3mm)
J = 1.750" - (44.4mm) - 16 Spline S = .624" - (15.8mm)
7.05" 5.36" S.S. 5-481X 3-3-1511KX 3-82-261 5-481X 3-2-159 902262-1
(179.0mm) (136.1mm)
C
-
L
L
(155.4mm)
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1410
© 2005 Dana Corporation
11
10 Series
Page 12
Coupling Shaft Configurations - Series 1310 - 1550
© 2005 Dana Corporation
12
10 Series
Page 13
Coupling Shaft Assembly
Standard Parts
Standard Tube Size 3.5" x 0.083" (88.90mm x 2.11mm)
Tube Part # 28-30-62
Nut 16-74-101
Series 1410
Minimum Length Tight Joint End Center Bearing End Assembly
Collapsed
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)/
to to (Shipping Companion
Centerline Centerline Strap) Flange
Tubing Formula: T = C
Tubing Formula: T = FF- CL (Collapsed) minus 8.500" - (215.9mm)
10.88” 9.19” 3-2-159 5-462X 3-28-557 28-30-62 3-53-1791 210873-1X 3-4-6561-1 911159
(276.3mm) (233.4mm)
Tubing Formula: T = FF-FF (Collapsed) minus 8.660" - (219.9mm)
10.16” 8.47” 3-2-159 5-160X 3-28-97 24-30-42 3-53-1881 210391-1X 3-1-4621 917043 (1)
mm) (215.1mm)
(258.0
C
-
L
9.19” S.S 5-462X 3-28-557 28-30-62 3-53-1791 210391-1X 3-4-6561 905771
(233.4mm)
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
L
C
-
(Collapsed) minus 7.810" - (198.3 mm)
L
L
R
Part Number
Center Bearing to
End Yoke/Flange
Face
4.13”
(104.9mm)
4.13”
(104.9mm)
3.25”
(82.5mm)
(1) Non-Standard tube size 3.0" x 0.083" (76.2 mm x 2.11 mm) Part #24-30-42
© 2005 Dana Corporation
13
10 Series
Page 14
Tube Type Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
θ
14
10 Series
Page 15
Tube Type Assembly
Standard Parts
Standard Tube Size 3.50" x 0.083" (88.90mm x 2.11mm)
Tube Part Number 28-30-62
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.500" - (38.1mm) - 15/16 Spline S = 4.718" - (119.8mm)
Tubing Formula: T = FF-FF (Collapsed) minus 13.160" - 334.264mm
14.56” 12.56” S.S. 5-481X 3-3-768KX 3-42-451 3-26-437 5-481X 3-2-939 910410 (1)
mm) (319.0mm)
(369.8
J = 1.500" - (38.1mm) - 16 Spline S = 2.344" - (59.5mm)
Tubing Formula: T = C
Tubing Formula: T = CL-FF (Collapsed) minus 11.840" - (300.7mm)
13.33” 11.33” S.S 5-481X 3-3-118KX 3-40-1531 3-28-557 5-481X 3-2-429 921668
(338.5mm) (287.7mm)
Tubing Formula: T = FF-FF (Collapsed) minus 13.220" - (335.7mm)
14.72” 11.34” 3-2-159 5-481X 3-3-118KX 3-40-1531 3-28-557 5-481X 3-2-159 905753
(373.8mm) (288.0mm)
Tubing Formula: T = FF-FF (Collapsed) minus 13.840" - (351.5mm)
15.34” 11.34” 3-2-309 5-481X 3-3-118KX 3-40-1531 3-28-557 5-481X 3-2-309 922256
(389.6mm) (288.0mm)
C
-
L
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
L
(Collapsed) minus 9.840" - (249.9mm)
L-CL
11.25” S.S 5-160X 3-3-118KX 3-40-1531 3-28-557 5-160X S.S. 905751
mm)
(285.7
Series 1410
J = 1.500" - (38.1mm) - 16 Spline S = 3.468" - (88.0mm)
ubing Formula: T =
T
C
CL-
(Collapsed) minus 11.000" - (279.4mm)
L
12.38” S.S. 5-481X 3-3-508KX 3-40-1491 3-28-557 5-481X S.S. 905785
(314.4mm)
Tubing Formula: T = C
14.06”
(357.1
mm) (314.2mm)
(Collapsed) minus 12.690" - (322.3mm)
L-CL
12.37”
3-2-159
5-481X 3-3-508KX 3-40-1491 3-28-557 5-481X S.S. 905754
Tubing Formula: T = FF-FF (Collapsed) minus 14.370" - (364.9mm)
15.90”
(403.8
mm) (318.0mm)
(1) Non-Standard tube size 2.5" x 0.056" (63.5 mm x 1.42 mm) Part #24-32-82
12.52”
3-2-159
5-481X 3-3-508KX 3-40-1491 3-28-557 5-481X 3-2-159 917821
15
© 2005 Dana Corporation
10 Series
Page 16
Short Coupled Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
16
10 Series
Page 17
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.250" - (57.1mm) - 10 Spline S = .937" - (23.8mm)
8.50” 5.50” 3-2-489 5-482X 3-3-1621KX 3-82-271 5-482X 3-2-489 202990-1
(215.9
mm) (139.7mm)
L-CL
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1480
Part Number
© 2005 Dana Corporation
17
10 Series
Page 18
Coupling Shaft Configurations - Series 1310 - 1550
© 2005 Dana Corporation
18
10 Series
Page 19
Coupling Shaft Assembly
Standard Parts
Standard Tube Size 3.5" x 0.083" (88.90mm x 2.11mm)
Part # 28-30-62
Nut 16-74-101
Series 1480
Minimum Length
Tight Joint End Center Bearing End Assembly
R
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = C
Tubing Formula: T = FF- CL (Collapsed) minus 10.190" - (258.8mm)
11.66” 9.66” 3-2-479 5-482X 3-28-537 28-30-62 3-4-3091-1 210391-1X 3-4-3091-1 911121
(296.1mm) (245.3mm)
L-CL
9.64”
(244.8
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
(Collapsed) minus 8.190" - (208.0mm)
L-CL
S.S.
mm)
5-482X 3-28-537 28-30-62 3-53-1821 210391-1X 3-4-3091-1 911122
Center Bearing to
End Yoke/Flange
Face
4.56”
(115.8mm)
4.56”
(115.8mm)
© 2005 Dana Corporation
19
10 Series
Page 20
Tube Type Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
θ
20
10 Series
Page 21
Tube Type Assembly
Standard Parts
Standard Tube Size 3.5" x 0.083" (88.90mm x 2.11mm)
Tube Part Number 28-30-62
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) (Dust Cap Kit) Strap)
J = 1.562" - (39.6mm) - 16 Spline S = 4.500" - (114.3mm)
Tubing Formula: T = C
J = 2.250" - (57.1mm) - 10 Spline S = .937" - (23.8mm)
Tubing Formula: T = FF-FF (Collapsed) minus 7.470" - (189.7mm)
8.50” 7.00” 3-2-489 5-482X 3-3-1621KX 3-40-731 3-28-497 5-482X S.S. 914673 (1)
(215.9mm) (177.8mm)
C
-
L
14.44” S.S. 5-482X 3-3-1641KX 3-40-1871 3-28-547 5-482X S.S 909741
(366.7
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
L
(Collapsed) minus 13.060" - (331.7mm)
L-CL
mm)
Series 1480
(1) Non-Standard tube size 3.0" x 0.095" (76.2 mm x 2.41 mm) Part #24-30-12
© 2005 Dana Corporation
21
10 Series
Page 22
Short Coupled Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
22
10 Series
Page 23
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.750" - (44.4mm) - 16 Spline S = 2.500" - (63.5mm)
13.51” 10.01” 4-2-669 5-155X 4-3-1241KX 4-82-401 5-155X 4-2-679 919473-1
(343.1mm) (254.2mm)
J = 2.500" - (63.5mm) - 16 Spline S = .813" - (20.7mm)
9.75” 5.75” 4-2-669 5-304X 4-3-1261KX 4-82-201 5-304X 4-2-669 204249-6
(247.6mm) (146.0mm)
C
-
L
L
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1550
© 2005 Dana Corporation
23
10 Series
Page 24
Coupling Shaft Configurations - Series 1310 - 1550
© 2005 Dana Corporation
24
10 Series
Page 25
Coupling Shaft Assembly
Standard Parts
d Tube Size 3.50 x 0.095 (88.90mm x 2.41mm)
Standar
Part # 28-30-22
Nut 16-74-101
Series 1550
Minimum Length
Tight Joint End Center Bearing End Assembly
R
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
C
-
L
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
L
to to (Shipping
Flange Face Centerline Strap)
Tubing Formula: T = C
(Collapsed) minus 8.160" - (207.2mm)
L-CL
9.61” S.S. 5-155X 4-28-307 28-30-22 4-53-401 210084-2X 4-4-4211-1 915959
mm)
(244.0
9.68” S.S. 5-609X 4-28-307 28-30-22 4-53-401 210084-2X 4-4-4211-1 914007
mm)
(245.8
Tubing Formula: T = FF- CL (Collapsed) minus 10.160" - (258.0mm)
11.56” 9.56” 4-2-669 5-609X 4-28-277 32-30-22 4-53-271 210084-2X 4-4-4211-1 913173 (1)
mm) (245.8mm)
(293.6
11.63” 9.63” 4-2-669 5-155X 4-28-307 28-30-22 4-53-401 210084-2X 4-4-4211-1 915962
mm) (244.6mm)
(295.4
11.68” 9.68” 4-2-699 5-609X 4-28-307 28-30-22 4-53-401 210084-2X 4-4-4211-1 915963
mm) (245.8mm)
(296.6
11.68” 9.68” 4-2-669 5-609X 4-28-307 28-30-22 4-53-401 210084-2X 4-4-4211-1 914212
mm) (245.8mm)
(296.6
Center Bearing to
oke/Flange
End Y
Face
4.35”
(110.5mm)
4.35”
(110.5mm)
4.35”
(110.5mm)
4.35”
(110.5mm)
4.35”
(110.5mm)
4.35”
(110.5mm)
(1) Non-Standard tube size 4.0" x 0.083" (101.6 mm x 2.11 mm) Part #32-30-22
© 2005 Dana Corporation
25
10 Series
Page 26
Tube Type Configurations - Series 1310 - 1550
θ
© 2005 Dana Corporation
θ
26
10 Series
Page 27
Tube Type Assembly
Standard Parts
Standard Tube Size 3.5" x 0.095" (88.9mm x 2.41mm)
Tube Part Number 28-30-22
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
L-CL
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 1.750" - (44.4mm) - 16 Spline S = 2.500" - (63.5mm)
Tubing Formula: T = C
11.72” S.S. 5-304X 4-3-1241KX 4-40-761 4-28-307 5-304X S.S. 906366
(399.2
Tubing Formula: T = FF-FF (Collapsed) minus 12.350" - (313.7mm)
13.83” 11.83” 4-2-669 5-155X 4-3-1241KX 4-40-951 4-28-657 5-155X S.S. 905282 (1)
mm) (300.4mm)
(351.2
Tubing Formula: T = FF-FF (Collapsed) minus 14.340” - (364.2mm)
15.72” 11.75” 4-2-669 5-155X 4-3-1241KX 4-40-761 4-28-307 5-155X 4-2-669 909469
mm) (298.4mm)
(399.3
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
C
-
(Collapsed) minus 10.340" - (262.6mm)
L
L
mm)
Series 1550
Tubing Formula: T = FF-FF (Collapsed) minus 14.350” - (364.5mm)
15.75” 11.75” 4-2-1159 5-609X 4-3-1241KX 4-40-761 4-28-307 5-609X S.S. 921600
(400.0mm) (298.4mm)
15.84” 11.84” 4-2-669 5-155X 4-3-1241KX 4-40-1051 4-28-307 5-155X 4-2-669 920142
mm) (300.7mm)
(402.3
15.91” 11.91” 4-2-699 5-155X 4-3-1241KX 4-40-761 4-28-307 5-155X 4-2-699 922836
(404.1mm) (302.5mm)
J = 1.750” - (44.4mm) - 16 Spline S = 5.000” - (127mm)
Tubing Formula: T = FF-FF (Collapsed) minus 17.970” - (456.4mm)
19.50”
(495.3
mm) (393.7mm)
15.50”
4-2-669
5-304X
4-3-1431KX
4-40-721
4-28-417 5-304X 4-2-669 913150
(1) Non-Standard tube size 3.50" x 0.156" (88.9 mm x 3.96 mm) Part #28-30-52
© 2005 Dana Corporation
27
10 Series
Page 28
Short Coupled Configurations - Series 1610 - 1880
© 2005 Dana Corporation
θ
28
10 Series
Page 29
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
L-CL
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.000" - (50.8mm) - 16 Spline S = 1.290" - (32.7mm)
11.47” S.S. 5-674X 5-3-3321KX 5-82-791-2 5-674X S.S. 822218-1
(291.3
mm)
J = 2.000" - (50.8mm) - 16 Spline S = 2.624” - (66.6mm)
15.51” 12.76” S.S. 5-674X 5-3-288KX 5-82-781 5-674X S.S. 821346-1
(393.9
mm)
(324.1
mm)
14.00” S.S. 5-674X 5-3-288KX 5-82-831-1 5-674X S.S. 807276-1
(355.6mm)
J = 2.000” - (50.8mm) - 16 Spline S = 3.248” - (82.5mm)
12.000” S.S. 5-674X 5-3-488KX 5-82-791-3 5-674X S.S. 814119-1
(304.8mm)
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1610
J = 2.000” - (50.8mm) - 16 Spline S = 4.750” - (120.6mm)
17.00” S.S. 5-279X 5-3-3121KX 5-82-961-5 5-279X S.S. 905908-7
(431.8mm)
17.94” S.S. 5-279X 5-3-3121KX 5-82-961-5 5-279X S.S. 905908-2
mm)
(455.7
J = 2.672” - (67.8mm) - 17/18 Involute Spline S = .531” - (13.5mm)
9.34” 5.59” 5-2-619 5-279X 5-3-1861KX 5-82-191 5-279X 5-2-619 207904-1
(237.2mm) (141.9mm)
J = 2.672” - (67.8mm) - 18 Involute Spline S = .750” - (19.0mm)
9.13” 5.37” 5-2-379 5-279X 5-3-3231X 5-82-161 5-279X 5-2-379 918926-1
(231.9
mm) (136.4mm)
J = 2.672” - (67.8mm) - 18 Involute Spline S = 1.563” - (39.7mm)
7.87”
199.9
mm)
S.S.
5-674X
5-3-2971KX 5-82-951 5-674X S.S. 815509-1
J = 2.676” - (67.9mm) - 18 Involute Spline S = .750” - (19.0mm)
9.12” 5.38” 5-2-379 5-279X 5-3-168KX 5-82-161 5-279X 5-2-379 906224-1
(231.6mm) (136.6mm)
© 2005 Dana Corporation
29
10 Series
Page 30
Coupling Shaft Configurations - Series 1610 - 1880
© 2005 Dana Corporation
30
10 Series
Page 31
Coupling Shaft Assembly
Standard Parts
Standard Tube Size 3.5" x 0.134" (88.9mm x 3.40mm)
Tube Part # 28-30-92
Nut 231502
Series 1610
Minimum Length Tight Joint End Center Bearing End Assembly
R
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = C
Tubing Formula: T = C
14.40” 11.650” 5-2-709 5-279X 5-28-327 32-30-52 5-53-271 210084-2X 5-4-7171-1 918637 (1)
mm) (295.9mm)
(365.7
Tubing Formula: T = FF-FF (Collapsed) minus 12.030” - (305.5mm)
14.41” 11.66” 5-2-599 5-279X 5-28-627 28-30-92 5-53-261 210084-2X 5-4-7171-1 816112
mm) (296.1mm)
(366.0
L-CL
11.56” S.S. 5-279X 5-28-327 32-30-52 5-53-271 210084-2X 5-4-7171-1 808499 (1)
(293.6mm)
11.64” S.S. 5-674X 5-28-627 28-30-92 5-53-261 210084-2X 5-4-7171-1 815967
(295.6
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
C
-
(Collapsed) minus 9.280" - (235.7mm)
L
L
mm)
(Collapsed) minus 12.020” - (305.3mm)
L-CL
Center Bearing to
End Yoke/Flange
Face
4.66”
(118.4mm)
4.66”
(118.4mm)
4.66”
(118.4mm)
4.66”
(118.4mm)
(1) Non-Standard tube size 4.0" x 0.134" (101.6 mm x 3.40 mm) Part #32-30-52
© 2005 Dana Corporation
31
10 Series
Page 32
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
32
10 Series
Page 33
T
ube Type Assembly
Standard Parts
Standard Tube Size 3.5" x 0.134" (88.9mm x 3.40mm)
Tube Part Number 28-30-92
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
L-CL
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.000” - (50.8mm) - 16 Spline S = 1.624” - (41.2mm)
Tubing Formula: T = FF-FF (Collapsed) minus 14.750” - (374.6mm)
17.13” 14.38” S.S. 5-674X 5-3-108KX 5-40-1011 5-28-627 5-279X 5-2-279 820590
(435.1mm) (365.2mm)
Tubing Formula: T = FF-FF (Collapsed) minus 17.500” - (444.5mm)
19.81” 14.31” 5-2-279 5-279X 5-3-108KX 5-40-1191 5-28-627 5-279X 5-2-279 907849
mm) (363.5mm)
(503.1
J = 2.000” - (50.8mm) - 16 Spline S = 3.935” - (99.9mm)
Tubing Formula: T = C
14.05” S.S. 5-279X 5-3-368KX 5-40-1241 5-28-837 5-279X S.S. 817414 (2)
(356.8mm)
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(Collapsed) minus 12.220” - (310.4mm)
L-CL
Series 1610
Tubing Formula: T = C
(Collapsed) minus 13.000” - (330.2mm)
L-CL
15.31” S.S. 5-674X 5-3-368KX 5-40-1151 5-28-627 5-674X S.S. 807148
mm)
(388.9
Tubing Formula: T = FF-FF (Collapsed) minus 15.750” - (400.0mm)
17.19” 14.44” 5-2-709 5-279X 5-3-368KX 5-40-1401 5-28-967 5-674X S.S. 820521 (2)
(436.6mm) (366.8mm)
18.13”
(460.55
15.32”
mm) (389.1mm)
5-2-629
5-279X
5-3-368KX
5-40-1151
5-28-627 5-674X S.S. 813641 (3)
J = 2.000” - (50.8mm) - 16 Spline S = 4.124” - (104.7mm)
Tubing Formula: T = C
(Collapsed) minus 15.120” - (384.0mm)
L-CL
17.44” S.S 5-674X 5-3-2261KX 5-40-1011 5-28-627 5-674X S.S. 805670
(442.9
mm)
Tubing Formula: T =C
(Collapsed) minus 15.280” - (388.1mm)
L-CL
17.56” S.S. 5-438X 5-3-2261KX 5-40-1051 5-28-327 5-438X S.S. 804536 (1)
mm )
(446.0
(1) Non-Standard tube size 4.0" x 0.134" (101.6 mm x 3.40 mm) Part #32-30-52
(2) Non-Standard tube size 3.55" x 0.207" (90.2 mm x 5.26 mm) Part #28-30-122
(3) Non-Standard tube size 3.5" x 0.134" (88.9 mm x 3.40 mm) Par
© 2005 Dana Corporation
t #28-30-92
33
10 Series
Page 34
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
34
10 Series
Page 35
Tube Type Assembly
Standard Parts
Standard Tube Size 3.5" x 0.134" (88.9mm x 3.40mm)
Tube Part Number 28-30-92
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
C
-
L
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
L
Series 1610
Part Number
Tubing Formula: T = C
(Collapsed) minus 15.940” - (404.8mm)
L-CL
18.20” S.S. 5-674X 5-3-2261KX 5-40-1011 5-28-887 5-674X S.S. 817062
(462.3 mm)
Tubing Formula: T = C
(Collapsed) minus 17.880” - (454.1mm)
L-CL
19.32” 16.57” 5-2-709 5-279X 5-3-2261KX 5-40-1371 5-28-967 5-674X S.S. 818681 (2)
mm) (420.8mm)
(490.7
20.25” 17.50” 5-2-279 5-279X 5-3-2261KX 5-40-1011 5-28-627 5-674X S.S. 818161
mm) (444.5mm)
(514.3
20.25” 17.50” S.S. 5-674X 5-3-2261KX 5-40-1011 5-28-627 5-279X 5-2-279 821523
mm) (444.5mm)
(514.3
Tubing Formula: T = FF-FF (Collapsed) minus 20.620” - (523.7mm)
22.94” 17.44” 5-2-279 5-279X 5-3-2261KX 5-40-1011 5-28-627 5-279X 5-2-279 906257
(582.7mm) (442.9mm)
Tubing Formula: T = FF-FF (Collapsed) minus 20.630” - (524.0 mm)
23.02” 17.52” 5-2-279 5-279X 5-3-2261KX 5-40-1011 5-28-627 5-279X 5-2-279 917829
(584.7mm) (445.0mm)
Tubing Formula: T = FF-FF (Collapsed) minus 20.780” - (527.8mm)
23.17” 17.67” 5-2-279 5-279X 5-3-2261KX 5-40-1051 5-28-327 5-279X 5-2-279 914921 (1)
mm) (448.8mm)
(588.5
(1) Non-Standard tube size 4.0" x 0.134" (101.6 mm x 3.40 mm) Part #32-30-52
(2) Non-Standard tube size 3.55" x 0.207" (90.2 mm x 5.26 mm) Par
(3) Non-Standard tube size 3.5" x 0.134" (88.9 mm x 3.40 mm) Part #28-30-92
© 2005 Dana Corporation
t #28-30-122
35
10 Series
Page 36
Short Coupled Configurations - Series 1610 - 1880
© 2005 Dana Corporation
θ
36
10 Series
Page 37
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 1.750” - (44.4mm)
J = 2.500” - (63.5mm) - 16 Spline S = 2.250” - (57.1mm)
J = 2.500” - (63.5mm) - 16 Spline S = 2.375” - (60.3mm)
J = 2.500” - (63.5mm) - 16 Spline S = 2.750” - (69.8mm)
J = 2.500” - (63.5mm) - 16 Spline S = 3.433” - (87.2mm)
15.23” 12.04” S.S. 5-675X 6-3-3321KX 6-82-1381 5-280X 6-2-15* 821821-1
mm) (305.8mm)
(386.8
J = 2.500” - (63.5mm) - 16 Spline S = 3.625” - (92.0mm)
J = 2.500” - (63.5mm) - 16 Spline S = 3.875” - (98.4mm)
L-CL
11.54” S.S. 5-675X 6-3-2741KX 6-82-1141 5-675X S.S 822742-1
(293.1mm)
11.38” S.S. 5-280X 6-3-2741KX 6-82-1171-10 5-675X S.S. 821735-1
mm)
(289.0
11.88” S.S. 5-675X 6-3-2741KX 6-82-1171-11 5-675X S.S. 805363-2
(301.7mm)
10.75” S.S. 5-675X 6-3-2741KX 6-82-1291 5-675X S.S 810482-1
(273.0mm)
11.75” S.S. 5-675X 6-3-2801KX 6-82-1171-1 5-675X S.S 806446-1
(298.4mm)
13.380” S.S. 5-675X 6-3-2631KX 6-82-1351-7 5-675X S.S 822242-1
mm)
(339.8
14.000” S.S. 5-675X 6-3-2671KX 6-82-1091-13 5-675X S.S 805361-7
(355.6mm)
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1710
14.41” S.S. 5-675X 6-3-2671KX 6-82-1341-1 5-675X S.S 805361-5
(366.0mm)
15.10” S.S. 5-675X 6-3-2671KX 6-82-1341-2 5-675X S.S 805361-10
(383.5mm)
J = 2.500” - (63.5mm) - 16 Spline S = 5.000” - (127.0mm)
16.00” S.S. 5-280X 6-3-3461KX 6-82-1351-3 5-280X S.S 916207-1
(406.4
mm)
37
© 2005 Dana Corporation
*Serrated Flange Yoke
10 Series
Page 38
Short Coupled Configurations - Series 1610 - 1880
© 2005 Dana Corporation
θ
38
10 Series
Page 39
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 5.250” - (133.3mm)
J = 2.500" - (63.5mm) - 16 Spline S = 5.500" - (139.7mm)
C
-
L
L
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
17.47" S.S. 5-280X 6-3-2651KX 6-82-1341-7 5-280X S.S 905357-6
mm)
(443.7
17.22” S.S. 5-675X 6-3-3441KX 6-82-1341-4 5-675X S.S 817262-5
(437.4
mm)
18.97” S.S. 5-675X 6-3-3441KX 6-82-1341-9 5-675X S.S 817262-3
mm)
(481.8
19.25” S.S. 5-675X 6-3-3441KX 6-82-1341-10 5-675X S.S 817262-9
mm)
(488.9
Series 1710
19.63” S.S. 5-675X 6-3-3441KX 6-82-1341-11 5-675X S.S 817262-8
mm)
(498.6
20.00” S.S. 5-675X 6-3-3441KX 6-82-1341-12 5-675X S.S 817262-4
(508.0mm)
J = 2.500" - (63.5mm) - 16 Involute Spline S = 2.499" - (63.5mm)
13.56" 10.35" S.S. 5-675X 6-3-3661KX 6-82-1391 5-280X 6-2-15 822202-1
(344.4mm)
(262.9
mm)
10.37” S.S. 5-280X 6-3-3661KX 6-82-1391 5-675X S.S 822803-1
(263.4
mm)
© 2005 Dana Corporation
39
10 Series
Page 40
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
40
10 Series
Page 41
Tube Type Assembly
Standard Parts
Standard Tube Size 4.0" x 0.134" (101.6mm x 3.40mm)
Tube Part Number 32-30-52
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 3.125” - (79.4mm)
Tubing Formula: T = FF-FF (Collapsed) minus 19.190” - 487.426mm
21.50” 15.50” 6-2-749 5-280X 6-3-2631KX 6-40-711 6-28-347 5-280X 6-2-749 907883
(546.1mm) (393.7mm)
J = 2.500” - (63.5mm) - 16 Spline S = 3.875” - (98.4mm)
Tubing Formula: T = C
Tubing Formula: T = FF-FF (Collapsed) minus 17.000” - (431.8mm)
19.42” 16.42” 6-2-739 5-675X 6-3-2671KX 6-40-541 6-28-347 5-280X S.S. 818864
(493.3mm) (417.0mm)
Tubing Formula: T = FF-FF (Collapsed) minus 20.000” - (508.0mm)
22.31” 16.31” 6-2-749 5-280X 6-3-2671KX 6-40-541 6-28-347 5-280X 6-2-749 906802
(566.7mm) (414.3mm)
C
-
L
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
L
(Collapsed) minus 14.000” - (355.6mm)
L-CL
16.38” S.S. 5-675X 6-3-2671KX 6-40-541 6-28-347 5-675X S.S. 806336 (1)
mm)
(416.0
16.39” S.S. 5-675X 6-3-2671KX 6-40-541 6-28-347 5-675X S.S. 805359
(416.3mm)
Series 1710
22.31” 16.31” 6-2-749 5-280X 6-3-2671KX 6-40-541 6-28-347 5-280X 6-2-749 912943 (1)
(566.7
mm )
mm)
(414.3
22.42” 16.42” 6-2-739 5-280X 6-3-2671KX 6-40-541 6-28-347 5-280X 6-2-739 918863
mm) (417.0mm)
(569.5
J = 2.500” - (63.5mm) - 16 Spline S = 5.250” - (133.4mm)
Tubing Formula: T = C
(Collapsed) minus 16.030” - (407.2mm)
L-CL
18.38” S.S. 5-280X 6-3-2651KX 6-40-521 6-28-347 5-280X S.S. 905358
(466.9mm)
18.38”
(466.9
mm)
S.S. 5-675X 6-3-2651KX 6-40-521 6-28-347 5-675X S.S. 805358
18.46” S.S. 5-675X 6-3-2651KX 6-40-521 6-28-347 5-675X S.S. 806354 (1)
(468.9mm)
(1) Non-Standard tube size 4.09" x 0.180" (103.9 mm x 3.57 mm) Part #32-30-72
© 2005 Dana Corporation
41
10 Series
Page 42
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
42
10 Series
Page 43
T
ube Type Assembly
d Parts
Standar
Standard Tube Size 4.0" x 0.134" (101.6mm x 3.40mm)
Tube Part Number 32-30-52
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 5.250” - (133.4mm)
Tubing Formula: T = FF-FF (Collapsed) minus 19.030” - (483.4mm)
21.38” 18.38” 6-2-739 5-280X 6-3-2651KX 6-40-521 6-28-347 5-280X S.S. 921142
(543.0
mm) (466.9mm)
21.38” 18.38” S.S. 5-280X 6-3-2651KX 6-40-521 6-28-347 5-280X 6-2-739 912072
mm) (466.9mm)
(543.0
Tubing Formula: T = FF-FF (Collapsed) minus 19.220” - (488.2mm)
21.63” 18.44” 6-2-749 5-280X 6-3-2651KX 6-40-521 6-28-347 5-280X S.S. 821662 (1)
mm) (468.4mm)
(549.4
C
-
L
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
L
Series 1710
J = 2.500” - (63.5mm) - 16 Spline S = 3.88” - (98.6mm)
Tubing Formula: T = FF-FF (Collapsed) minus 20.000” - (508.0mm)
22.42” 16.42” 6-2-749 5-280X 6-3-2651KX 6-40-521 6-28-347 5-280X 6-2-749 917832
mm) (417.0mm)
(569.5
J = 2.500” - (63.5mm) - 16 Spline S = 5.500” - (139.7mm)
Tubing Formula: T = C
(487.2mm)
(Collapsed) minus 17.470” - (443.7mm)
L-CL
19.18" S.S. 5-280X 6-3-3441KX 6-40-521 6-28-467 5-280X S.S. 911435
19.81” S.S. 5-280X 6-3-3441KX 6-40-521 6-28-467 5-280X S.S. 913045 (1)
(503.2
mm)
(1) Non-Standard tube size 4.09" x 0.180" (103.9 mm x 3.57 mm) Part #32-30-72
© 2005 Dana Corporation
43
10 Series
Page 44
Short Coupled Configurations - Series 1610 - 1880
© 2005 Dana Corporation
θ
44
10 Series
Page 45
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 2.328” - (59.1mm)
C
-
L
L
12.38” S.S. 5-677X 6.3-3-41KX 6.3-82-21-1 5-677X S.S. 810664-1
(314.5mm)
13.88” S.S. 5-677X 6.3-3-41KX 6.3-82-21-4 5-677X S.S. 810664-4
(352.5
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
mm)
Series 1760
© 2005 Dana Corporation
45
10 Series
Page 46
Coupling Shaft Configurations - Series 1610 - 1880
© 2005 Dana Corporation
46
10 Series
Page 47
Coupling Shaft Assembly
d Parts
Standar
Standard Tube Size 4.0" x 0.134" (101.6mm x 3.40mm)
Washer 230123-6
Nut 20-74-91
Series 1760
Minimum Length Tight Joint End Center Bearing End Assembly
R
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = C
C
-
L
13.63” S.S. 5-677X 6.3-28-17 32-30-72 6.3-53-21 210875-1X 6.3-4-821-1 811456 (1)
(346.2
13.63” S.S. 5-677X 6.3-28-17 32-30-92 6.3-53-21 210661-1X 6.3-4-821-1 810251
(346.2
13.63” S.S. 5-677X 6.3-28-17 32-30-72 6.3-53-21 210661-1X 6.3-4-821-1 810661 (1)
(346.2mm)
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
L
(Collapsed) minus 11.250” - (285.8mm)
L-CL
mm)
mm)
Center Bearing
to
End Yoke/Flange
Face
6.2”
(157.5mm)
6.2”
(157.5mm)
6.2”
(157.5mm)
(1) Non-Standard tube size 4.09" x 0.180" (103.9 mm x 4.57 mm) Part #32-30-72
© 2005 Dana Corporation
47
10 Series
Page 48
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
48
10 Series
Page 49
Tube Type Assembly
Standard Parts
Standard Tube Size 4.0" x 0.134" (101.6mm x 0.340mm)
Tube Part Number 32-30-92
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 2.500” - (63.5mm) - 16 Spline S = 2.328” - (59.1mm)
Tubing Formula: T = C
J = 2.500” - (63.5mm) - 16 Spline S = 4.687” - (119.0mm)
Tubing Formula: T = C
L-CL
15.97” S.S. 5-677X 6.3-3-41KX 6-40-541 6.3-28-17 5-677X S.S. 810654 (1)
(405.6
17.81” S.S. 5-677X 6.3-3-21KX 6-40-521 6.3-28-17 5-677X S.S. 810074
(452.4mm)
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(Collapsed) minus 13.660” - (346.9mm)
L-CL
mm)
(Collapsed) minus 15.500” - (393.7mm)
L-CL
Series 1760
17.81” S.S. 5-677X 6.3-3-21KX 6-40-521 6.3-28-17 5-677X S.S. 810566 (1)
mm)
(452.4
(1) Non-Standard tube size 4.09" x 0.180" (103.9 mm x 4.57 mm) Part #32-30-72
© 2005 Dana Corporation
49
10 Series
Page 50
Short Coupled Configurations - Series 1610 - 1880
© 2005 Dana Corporation
θ
50
10 Series
Page 51
Short Coupled Assembly
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 3.000” - (76.2mm) - 16 Spline S = 3.376” - (85.7mm)
17.38” 14.00” 6.5-2-329 5-281X 6.5-3-1431KX 6.5-82-451-5 5-281X S.S. 916971-1
(441.4mm) (355.6mm)
J = 3.000” - (76.2mm) - 16 Spline S = 5.000” - (127.0mm)
19.57” 16.19” 6.5-2-329 5-281X 6.5-3-1371KX 6.5-82-461-8 5-676X S.S. 819530-2
mm) (411.2mm)
(497.1
L-CL
13.00” S.S. 5-676X 6.5-3-1431KX 6.5-82-451-1 5-676X S.S. 805248-1
(330.2mm)
14.00” S.S. 5-676X 6.5-3-1431KX 6.5-82-451-5 5-676X S.S. 819702-1
(355.6
mm)
Flange Yoke U-Joint Slip Yoke Yoke Shaft U-Joint Flange Yoke
Series 1810
J = 3.250” - (82.6mm) - 18 Involute Spline S = 1.125” - (28.6mm)
8.22” S.S. 5-676X 6.5-3-1451KX 6.5-82-511-1 5-676X S.S. 810500-1
mm)
(208.8
© 2005 Dana Corporation
51
10 Series
Page 52
Coupling Shaft Configurations - Series 1610 - 1880
© 2005 Dana Corporation
52
10 Series
Page 53
Coupling Shaft Assembly
Standard Parts
d Tube Size 4.5" x 0.134" (114.3mm x 3.40mm)
Standar
ube Part # 36-30-62
T
Washer 230123-6
Nut 20-74-91
Series 1810
Minimum Length Tight Joint End Center Bearing End Assembly
R
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
to to (Shipping
Flange Face Centerline Strap)
Tubing Formula: T = C
Tubing Formula: T = FF-FF (Collapsed) minus 14.970” - (380.2mm)
17.60” 14.22” 6.5-2-329 5-281X 6.5-28-117 36-30-62 6.5-53-91 210875-1x 6.5-4-1891 911617
(447.0mm) (361.2mm)
L-CL
14.20” S.S. 5-676X 5.6-28-117 36-30-62 6.5-53-171 210661-1x 6.5-4-3591-1 804149
(360.7mm)
14.20” S.S. 5-676X 5.6-28-127 36-30-22 6.5-53-181 210661-1x 6.5-4-3591-1 804248 (1)
(360.7mm)
Flange Yoke U-Joint Tube yoke Tubing Midship Center End Yoke
(Collapsed) minus 11.590” - (294.4mm)
L-CL
Center Bearing
to
End Yoke/Flange
Face
6.2”
(157.5mm)
6.2”
(157.5mm)
6.2”
(157.5mm)
(1) Non-Standard tube size 4.50" x 0.259" (114.3 mm x 6.58 mm) Part #36-30-22
© 2005 Dana Corporation
53
10 Series
Page 54
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
54
10 Series
Page 55
Tube Type Assembly
Standard Parts
Standard Tube Size 4.5" x 0.134" (114.3mm x 3.40mm)
Tube Part Number 36-30-62
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 3.000" - (76.2mm) - 16 Spline S = 3.375" - (85.7mm)
Tubing Formula: T = FF-FF (Collapsed) minus 21.990" - (558.5mm)
24.87” 18.12” 6.5-2-329 5-281X 6.5-3-1351KX 6.5-40-201 6.5-28-117 5-281X 6.5-2-329 917835
(631.7mm) (460.2mm)
Tubing Formula: T = FF-FF (Collapsed) minus 22.410" - (569.2mm)
25.19” 18.44” 6.5-2-329 5-281X 6.5-3-1351KX 8-40-91 6.5-28-127 5-281X 6.5-2-329 908392 (1)
mm) (468.4mm)
(639.8
J = 3.000" - (76.2mm) - 16 Spline S = 5.000" - (127.0mm)
Tubing Formula: T = C
L-CL
19.75” S.S. 5-676X 6.5-3-1371KX 6.5-40-191 6.5-28-117 5-676X S.S. 804848
(501.7mm)
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(Collapsed) minus 17.000" - 431.8mm
L-CL
Series 1810
Tubing Formula: T = FF-FF (Collapsed) minus 20.380" - (517.7mm)
23.12” 19.740” 6.5-2-329 5-281X 6.5-3-1371KX 6.5-40-191 6.5-28-117 5-676X S.S. 821376
mm) (501.4mm)
(587.2
Tubing Formula: T = FF-FF (Collapsed) minus 20.870" - (530.1mm)
23.71” 20.13” 6.5-2-15 5-281X 6.5-3-1371KX 8-40-101 6.5-28-127 5-676X S.S. 821663 (1)
(602.2
mm) (511.3mm )
ubing Formula: T = FF-FF (Collapsed) minus 23.750” - (603.3mm)
T
26.50” 19.75” 6.5-2-329 5-281X 6.5-3-1371KX 6.5-40-191 6.5-28-117 5-281X 6.5-2-329 914582
mm) (501.7mm)
(673.1
26.68”
(677.7
mm) (505.9mm)
19.92”
6.5-2-329
5-281X 6.5-3-1371KX 6.5-40-191 6.5-28-117 5-281X 6.5-2-329 906323
(1) Non-Standard tube size 4.50" x 0.250" (114.3 mm x 6.58 mm) Part #36-30-22
© 2005 Dana Corporation
55
10 Series
Page 56
Tube Type Configurations - Series 1610 - 1880
θ
θ
θ
© 2005 Dana Corporation
56
10 Series
Page 57
Tube Type Assembly
Standard Parts
Standard Tube Size 4.5" x 0.259" (114.3mm x 6.58mm)
Tube Part Number 36-30-22
Series 1880
Minimum Length
Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF C
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
Tubing Formula: T = FF-FF (Collapsed) minus 18.440" - (468.4mm)
21.28” 18.78” 8-2-119 5-308X 8-3-391KX 8-40-91 8-28-147 5-308X S.S. 916587
mm) (477.0mm)
(540.5
Tubing Formula: T = FF-FF (Collapsed) minus 19.440" - (493.8mm)
22.19” 18.69” 8-2-109 5-308X 8-3-391KX 8-40-91 8-28-147 5-308X S.S. 908537
(563.6mm) (474.7mm)
Tubing Formula: T = FF-FF (Collapsed) minus 22.940" - (582.7mm)
25.69” 18.69” 8-2-109 5-308X 8-3-391KX 8-40-91 8-28-147 5-308X 8-2-109 905869
mm) (474.7mm)
(652.5
J = 3.000" - (76.2mm) - 16 Spline S = 4.687" - (119.0mm)
Tubing Formula: T = FF-FF (Collapsed) minus 24.562" - (623.8mm)
27.31” 20.31” 8-2-109 5-308X 8-3-411KX 8-40-101 8-28-147 5-308X 8-2-109 905882
(693.7mm) (515.9 mm)
L-CL
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
© 2005 Dana Corporation
57
10 Series
Page 58
Spicer®Life Series
Driveshafts
The codes in this section are for quick reference to:
™
© 2005 Dana Corporation
J = Major spline diameter and number of spline teeth
S = Total slip
FF-FF = Flange f
C
CL-
= Center
L
S.S. = Shipping strap
ß = Slip Joint max working angle (degrees)
θ = Tight Joint max working angle (degrees)
ube Length
T
T =
R = Center line of center bearing to center line of end yoke/flange face
M = Centerline to Flange Face
ace to flange face
line to center
line
1
SPL Series
Page 59
Tube Type
Standard Parts
Standard Tube Size 3.5" x 0.083" (88.9mm x 2.11mm)
ube Part Number 28-30-62
T
Series SPL55
ß
J
S
C
L-CL
Minimum Length Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-C
L
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Centerline Centerline Strap) Dust Cap Kit) Strap)
J = 1.562" - (39.6mm) 16 Spline S = 2.500" - (63.5mm)
Tubing Formula: T = A-2 (Collapsed) minus 10.090" - (256.3mm)
Tubing Formula: T = FF-CL (Collapsed) minus 12.090" - (307.1mm)
13.55” 11.55” 3-2-479 SPL55-1X 3-3-1601KX 3-40-1571 3-28-537 SPL55-1X S.S. 922636
mm) 293.4mm)
(344.2
C
L-CL
11.57” S.S. SPL55-1X 3-3-1601KX 3-40-1571 3-28-537 SPL55-1X S.S 922637
(293.9mm)
Flange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
© 2005 Dana Corporation
2
SPL Ser
ies
Page 60
Coupling Shaft Assembly
θ
C
L-CL
Series SPL140
R
Minimum Length
Tight Joint End Center Bearing End R Assembly
Collapsed Part Number
FF-C
L
Flange Face
C
L-CL
Centerline or S.S. Kit Tube Shaft Bearing (Assy)
oke U-Joint Tube Yoke Tubing Midship Center End Yoke
Flange Y
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = CL-CL (Collapsed) minus 11.300" - (287.0mm)
13.68” S.S. SPL140X 140-28-17 100-30-3 140-53-11 210121-1X 140-4-11-1 140CS54025
(347.5mm)
13.68” S.S. SPL140X 140-28-17 100-30-3 140-53-11 5003326 140-4-11-1 140CS54031
mm)
(347.5
Tubing Formula: T = CL-CL (Collapsed) minus 11.600" - (294.6mm)
13.79” S.S. SPL140X 140-28-17 100-30-5 140-53-11 5003323 140-4-1011-1 140CS54013
mm)
(350.3
13.79” S.S. SPL140X 140-28-17 100-30-5 140-53-11 5003326 140-4-1011-1 140CS54019
mm)
(350.3
13.79” S.S. SPL140X 140-28-17 100-30-5 140-53-11 5003323 140-4-1011-1 140CS54043
(350.3
mm)
13.79” S.S. SPL140X 140-28-17 100-30-3 140-53-11 5003323 140-4-1011-1 140CS54037
(350.3mm)
Center
ing to
Bear
end Yoke
ace
Flange F
5.96”
(151.5mm)
5.96”
(151.5mm)
6.10”
(154.5mm)
6.10”
(154.5mm)
6.10”
(154.5mm)
6.10”
(154.5mm)
© 2005 Dana Corporation
3
SPL Ser
ies
Page 61
T
ube Type Assembly
Standard Parts
Standard Tube Size 4.4" x 0.14" (111.7mm x 3.5mm)
Tube Part Number 100-30-3
Series SPL140
ß
J
S
C
L-CL
Minimun Length Tight Joint End Center Bearing End Assembly
Collapsed Part Number
FF-FF CL-CLFlange Yoke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
Flange Face Centerline or S.S. Kit Assembly Kit or S.S.
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 3.07" - (78mm) - 30 Spline S= 4.33" - (110mm)
Tubing Formula: T = A-2 (Collapsed) minus 14.370” - (365.0mm) Minimum T = 2.678" - (68.0mm)
16.92" S.S. SPL140X 140-82-21X 140-55-21X 140-28-17 SPL140X S.S. 140DS55007
mm)
(429.8
16.92" S.S. SPL140X 140-82-21X 140-55-21X 140-28-17 SPL140X S.S. 140DS55001(1)
mm)
(429.8
(1) Non-Standard tube size 4.3" x 0.20" (110 mm x 5 mm) Part #100-30-5
© 2005 Dana Corporation
4
SPL Series
Page 62
Coupling Shaft Assembly
θ
C
L-CL
Series SPL170
R
Minimum Length Tight Joint End Center Bearing End R Assembly
Part Number
FF-C
L
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
C
L-CL
Flange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = CL-CL (Collapsed) minus 12” - (304.8mm)
14.45” S.S SPL170X 170-28-17 120-30-3 250-53-11 5003326 170-4-1271-1 170CS54027C
(367.0mm)
Center
Bearing to
end Yoke
ace
Flange F
6.30”
(160mm)
14.47” S.S SPL170X 170-28-17 120-30-3 250-53-11 5003323 170-4-1271-1 170CS54018C
(367.5mm)
14.45” S.S SPL170X 170-28-17 120-30-4 250-53-11 5003323 170-4-1271-1 170CS54016C
mm)
(367.0
6.30”
(160mm)
6.30”
(160mm)
© 2005 Dana Corporation
5
SPL Ser
ies
Page 63
T
ube Type Assembly
Standard Parts
Standard Tube Size 4.9" x 0.12" (124.5mm x 3.0mm)
Tube Part Number 120-30-3
Series SPL 170
C
L-CL
Minimum Length
ß
J
S
Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF CL-CLFlange Y
Flange Face
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 3.85” - 98mm - 38 Spline S = 4.3” - 110mm
Tubing Formula: T = C
Centerline or S.S. Kit Assembly Kit or S.S.
(Collapsed) minus 14.60" - (371.0mm) Minimum T = 2.678" - (68.0mm)
L-CL
17.28” S.S. SPL170X 170-82-21X 250-55-31X 170-28-17 SPL170X S.S. 170DS55002C (1)
(438.9mm)
17.28” S.S. SPL170X 170-82-21X 250-55-31X 170-28-17 SPL170X S.S. 170DS55001C
(438.9mm)
oke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
20.08” S.S. SPL170X 170-82-71X 170-55-21-2X 170-28-27 SPL170X S.S. 170DS55005C (2)
mm)
(510.0
(1) Non-Standard tube size 5.06" x 1.67" (128.5 mm x 4.25 mm) Part #120-30-4
(2) Non-Standard tube size 4.72" x 0.19" (120 mm x 5 mm) Part #110-30-5
© 2005 Dana Corporation
6
SPL Series
Page 64
Coupling Shaft Assembly
θ
C
L-CL
Series SPL250
R
Minimum Length Tight Joint End Center Bearing End R Assembly
Collapsed Part Number
FF-FF CL-CLFlange Yoke U-Joint Tube Yoke Tubing Midship Center End Yoke
Flange Face Centerline or S.S. Kit Tube Shaft Bearing (Assy)
to to (Shipping
Centerline Centerline Strap)
Tubing Formula: T = CL-CL (Collapsed) minus 12.67” - (321.8mm)
15.12” S.S SPL250X 250-28-17 120-30-4 250-53-11 5003323 250-4-21-1 250CS54005C
(384.0mm)
Center
Bearing to
Yo ke
end
Flange Face
6.45”
(164mm)
15.12” S.S SPL250X 250-28-17 120-30-5 250-53-11 5003326 250-4-21-1 250CS54018C
mm)
(384.0
. 15.05” S.S SPL250X 250-28-17 120-30-5 250-53-11 5003323 250-4-21-1 250CS54006C
mm)
(382.3
6.45”
(164mm)
6.45”
(164mm)
© 2005 Dana Corporation
7
SPL Series
Page 65
T
ube Type Assembly
Standard Parts
Standard Tube Size 5.06" x 0.17" (128.5mm x 4.32mm)
Tube Part Number 120-30-4
Series SPL 250
C
L-CL
Minimum Length
ß
J
S
Slip Joint End Tight Joint End Assembly
Collapsed Part Number
FF-FF CL-CLFlange Y
Flange Face
to to (Shipping (Includes (Shipping
Flange Face Centerline Strap) Dust Cap Kit) Strap)
J = 3.85” - (98mm) S = 4.33” - (110mm)
Tubing Formula: T = CL-CL (Collapsed) minus 15.00" - 381.0mm
Centerline or S.S. Kit Assembly Kit or S.S.
17.71” S.S. SPL250X 250-82-21X 250-55-31X 250-28-17 SPL250X S.S. 250DS55006C (1)
(450.0mm)
17.71” S.S. SPL250X 250-82-21X 250-55-31X 250-28-17 SPL250X S.S. 250DS55005C
(450.0mm)
oke U-Joint Slip Yoke Tube Shaft Tube Yoke U-Joint Flange Yoke
(1) Non-Standard tube size 5.12" x 0.19" (130 mm x 5 mm) Part #120-30-5
© 2005 Dana Corporation
8
SPL Series
Page 66
®
Spicer
Wing Bearing
© 2005 Dana Corporation
Wing Bearing
Page 67
© 2005 Dana Corporation
Wing Bear
ing
Page 68
© 2005 Dana Corporation
Wing Bear
ing
Page 69
© 2005 Dana Corporation
Wing Bear
ing
Page 70
© 2005 Dana Corpor
Wing Bearing
ation
Page 71
© 2005 Dana Corporation
Wing Bear
ing
Page 72
© 2005 Dana Corporation
Wing Bearing
Page 73
© 2005 Dana Corporation
Wing Bear
ing
Page 74
© 2005 Dana Corporation
Wing Bearing
Page 75
© 2005 Dana Corporation
Wing Bearing
Page 76
© 2005 Dana Corporation
Wing Bearing
Page 77
© 2005 Dana Corporation
Wing Bearing
Page 78
© 2005 Dana Corporation
Wing Bearing
Page 79
© 2005 Dana Corporation
Wing Bear
ing
Page 80
© 2005 Dana Corporation
Wing Bear
ing
Page 81
© 2005 Dana Corporation
Wing Bearing
Page 82
© 2005 Dana Corporation
Wing Bearing
Page 83
© 2005 Dana Corporation
Wing Bear
ing
Page 84
© 2005 Dana Corporation
Wing Bearing
Page 85
© 2005 Dana Corporation
Wing Bear
ing
Page 86
© 2005 Dana Corporation
Wing Bearing
Loading...