Spice M-4580 User Manual

PN: 5839002387

Spice Mobiles Ltd. ©2009. All rights are reserved. No part of this
document may be reproduced without permission. All trademarks and
brand names mentioned in this publication are property of their
respective owners.

While all efforts have been made to ensure the accuracy of all contents
in this manual, we assume no liability for errors or omissions or by
statements of any kind in this manual, whether such errors are
omissions or statements resulting from negligence, accidents, or any
other cause. The contents of this manual are subject to change without
notice.

Protect your environm ent! We strive to produce products in compliance
with global environmental standards. Please consult your local
authorities for proper disposal.

Note: User’s Manual is Just to guide the user about the functionality of
the phone. This dose not seems any certificate of technology. Some
functions may very due to modifications and up gradations of software
or due to print mistake.

S AFETY PR ECAU TIONS

Before using your phone, please read the following important
information to eliminate or reduce any possibility of causing damage
and personal injury.

Do not use wireless phones while driving.

Switch off wireless devices in aircraft. The signal

may cause interference. Using them on aircraft is

illegal.

Do not use mobile phones where blasting is in
progress. Follow any regulations and rules strictly.

Do not use mobile phones at a refueling point. Don’t
use near fuel or chemicals

Follow any regulations or rules in hospital and health
care facilities. Switch phone off near medical
equipment.

All wireless devices may get interference that could
affect performance.

Only qualified service personnel can install or repair
this device.

Use only approved accessories and batteries.

Use only in normal position. Do not expose your

phone to extreme high temperatures above +60℃
（+140°F）. Do not use anything static to clean your

phone.

Ensure the phone is turned on and in service. Enter

the emergency number, then press Pick Up key.
Give your location. Do not end the call until told to
do so.

Table of Content

INFORMATION ...................................................................... 6

..................................................................................................... 6

Service

........................................................................................ 6

.................................................................................................... 6

YOUR MOBILE PHONE ........................................................ 7

of Phone Keys ............................................................................. 7

of Keys

........................................................................................ 8

Screen

......................................................................................... 9

Icons

.......................................................................................... 10

Light

........................................................................................... 10

STARTED ............................................................................. 11

Call ............................................................................................ 11

the SIM Card

............................................................................. 11

the T-Flash Memory Card

.......................................................... 12

the Battery

................................................................................. 13

Your Phone On/Off

.................................................................... 14

the Personal Handsfree Handset

................................................ 14

.............................................................................................. 15

Calls .......................................................................................... 15

Calls

.......................................................................................... 16

in Call

......................................................................................... 16

TO MENU OPERATIONS .................................................... 17

Book ........................................................................................... 17

................................................................................................... 20

Center

........................................................................................ 24

................................................................................................... 30

Center

........................................................................................ 36

profiles

........................................................................................ 39

................................................................................................... 40

................................................................................................... 42

Spice

.......................................................................................... 43

INFORMATION .................................................................... 48

of Passwords .............................................................................. 48

Information

................................................................................. 49

& Maintenance

........................................................................... 51

Calls

.......................................................................................... 52

.............................................................................................. 53

A: Guidance On Entry Methods .................................................. 53

B: Troubleshooting

..................................................................... 55

C: Available Accessories

............................................................ 56

D: F CC Statement

..................................................................... 56

6

GENERAL INFORMATION

Antenna

Use of other antenna devices could damage your mobile phone and
reduce performance. Your phone h as a built-in antenna. Don’t touch the
antenna area unnecessarily when the phone is switched on. Contact
with the antenna affects call quality and may cause the phone to
operate at a higher power level than otherwise needed.

Network Servic e

A lot of features described in this manual are called network service.
They are special services provided by wireless service providers. You
should subscribe to these services from your home service provider
and learn instructions on uses before you select the network you want
to use.

Accessories

Li-Ion battery is the manufacturer-approved rechargeable battery
available for your phone. May be some batteries performs best after
several full charge/discharge cycles.
Use batteries, chargers and accessories approved by the phone
manufacturer with this particular model. The use of any other types
will invalidate any approval or warranty applying to the phone, and may
be dangerous.
Please consult with your dealer for availability of approved accessories.

7

KNOW YOUR MOBILE PHONE

Positions o f Phone Keys

1. Earpiece

9. Torch/ Currency reader keys

2. Screen

10. Right Soft Key

3. Left Soft Key/ Slave SIM Call
Key

11. Cord h ol e

4. Selection key

12.Microphone

5. Master SIM Call Key

13. Battery Cover

6. Hang up and Power key

14. OK key

7. Charger and
accessori es co n ne ct or

15. Number keys

8. Torch/ Currency Checker

8

Functions of Keys

Key

Name

Description

Master

SIM Call

Key

Making or answering a call from

Master SIM.
In the standby mode, press this key to

access the Call Logs.

Call End

Key

End an ongoing call.

Press and hold this key to turn on or
off the mobile phone.
In the menu mode, press this key to
return the standby mode and cancel
current operations.

Press this key to stop the alarm
ringing once the alarm rings.

Right Soft

Key

Use the right soft keys to execute to
functions indicated at the right of the

prompt bar on the screen.

Slave SIM

Call Key /

Left Soft

Key

Use the left soft key to execute to
functions indicated at the left of the

prompt bar on the screen.
In the standby mode, press it to access
main menu.

When the “Master SIM & Slave SIM

open” has been selected, press the left
soft key to

making a call with Slave

SIM card after press the nu mber k ey or

get into the function of phonebook.

9

Selection

Key

Scrolling options in the f unction list or
the phone book.
In the edit mode, it is used for moving
the cursor.
In the standby mode, press it to

activate a specified function.

Numeric

Keys

Used to enter numbers, letters and

some special characters.
In the standby mode, press and hold
the # key to activate Silent mode,
press and hold the Numeric key 0 to
activate FM function.
In the edit mode, you can press the #
key to switch t he input method, press
the * key to display the symbols.

Display Screen

Your mobile phone has a single LCD display, which consists of three
main areas:
The First line displays status icons, which indicate the signal strength,
the remaining power of the battery, etc.
The Middle lines display text and graphics, including numbers, text,
animated icons and the information you enter.
The Last line displays the currently available operations assigned to the
left or right soft key.

10

S tatus Icons

Network Signal

Connecting GPRS and using GPRS

Connecting GPRS but no data alternating

Divert all Voice Calls

Auto Keypad Lock

Alarm Cl ock is activated

Battery Status

Missed Calls

New SMS/MMS or Mess age Memory Full

MMS is busy

Roaming Startup

WAP Message

Sound Status

Ring

Light. only

Note: The picture is for reference only, the product is subject to the real
one.

Back Light

You c an set the Back Light for the display and k eypad through options
in the menu. The backlight will be off automatically without any key
operation.

11

GETTING STARTED

First Call

 Insert a SIM card (Switch off your phone at first, and then remove

the battery). Enter the area code and the phone number and
press Pick Up Key.
Tip: Before you get started, you must insert a valid SIM card in
your phone and charge the battery first.

 SIM Card: Please refer to “Mounting the SIM Card” for more

reference on installation.

 Charging the battery: please refer to “Charging the Battery” for

more details.

Mounting the SIM Card

Your mobile phone number, PIN (Personal Identification Number), PIN2,
PUK (Personal Unlock Key), PUK2 (Personal Unlock Key2), IMSI
(International Mobile Subscriber Identity), the network information, the
phonebook data, SMS (short messages) and other data are stored in
your SIM card.
Note: This particular phone model only supports the SIM cards of 1.8V
and 3V.
 Some network operators don’t offer PIN2 and PUK2, so functions

using those passwords will be unavailable.

 The SIM card and its contacts can be easily damaged by

scratches or bending , so be careful while handling, inserting or

removing the card.
 Keep all miniature SIM cards out of children’s reach.
Note: Alw ays make sure that the p hone is switched off before you insert
or remove the SIM card, otherwise it may damage the SIM card.

Mounting

1. Remove the battery cover by sliding it.

12

2. Open the gold cap from the Hinge Type Connector. Lay the SIM card

which gold contacts face down on the Connector, then close it.

3. Replace the battery and close the cover tightly.

Note:

 If the SIM Card is not installed properly or damaged, the prompt

words “Insert SIM” will display on the screen af ter y ou sw itch on y our
phone. Remove the SIM Card and mount it again as shown in the
picture

 If “Insert SIM” still appears on the screen after you have inserted the

SIM correctl y. Please ensure there is no stain on the surface of the
SIM card. If there are some stains on it, please clean away them
with rubber carefully and then try again.

 If the screen displays that the SIM card is locked permanently,

please consult with your network operator.

Mounting the T-Flash Memory Card

Please follow steps described as below:
Open the gold cap from the Hinge Type Connector. Lay the T-Flash
card which gold contacts face down on the Connector, then close it.
Align the card to the arrow sign as the following picture shows:

Note:

Please plug the T-Flash card when the phone is power off. Otherwise
the phone is needed to restart to guarantee normal function of the
T-Flash card. Do not plug the T-Flash card when phone is power on, as
abusing may cause abnormal circumstances.

13

Charging the Battery

Note: Pleas e always keep your phone connector and charger dry.

1. Connect the connector of the travel adapter to the phone.

2. Plug the travel adapter into a proper AC wall outlet.

3. When your phone indicates that the battery is fully charged,

please pull the travel adapter out from the I/O socket of the
phone.

Tip: 1. If the battery is totally empty or not enough, it may take a few

minutes before the charging indicator appears on the screen.

2. You can turn on/off, and use the phone while charging.
Warning: Make sure that the standard voltage/power of the place
where you charge the battery matc hes with the rated voltage/power of
our travel adapter.

14

Switching Your Phone On/Off

 Press and hold Power Key for a few seconds t o switch your phone

on.

 If the phone ask for a phone lock code:

Enter the phone lock code, and press OK.

 If the phone ask for a PIN code:

Enter the PIN code, and press OK. The PIN code is usually supplied
with the SIM card. Please consult your network operator for more
information.

 Access the standby mode.

Press and hold Power Key for a few seconds to switch your phone
off.

Using the Personal Handsfree Hand set

Connect the handsfree handset to your mobile phone, you can still
answer calls and use the microphone without holding the phone.

15

CALLING

Making Calls

1. Enter the phone number (with the area code)

2. Press Pi ck up Key to make a call.

3. Press Hang up Key to end a call.

Making International Calls

1. Press the * key twice for the international prefix symbol +.

2. Enter the country code, area code and phone number.

3. Press Pick up Key to make a call.

Making Extension Calls

1. Enter the host number , and pre ss the * key three or four times for the

extension prefix symbol P or W.

2. Enter the extension number, and press Pick up Key to m ake a cal l.

Clear Wrong Enters

Press right soft key to delete the last character on the screen. Hold right
soft key will clear all you entered.

Making a call from the Phone Book

Method 1:

1. Press right soft key to access the Phone Book List. Scroll to search

the desired number. (Enter the first letter or more of the name and
press the selection key Up/Down to reach the desired name.)

2. Press Pick up Key to call the number.

Method 2:

1. Select” Menu > Phonebook”.

2. Select” Quick Search” to find the number you wants, and presses

Pick up Key to call the number.

Last Number Redial

1. In the standby mode, press Pick up Key to acces s the Call Logs.

2. Press the Up/Down key to reach the desired number or name and

press Pick up Key .

16

Speed Dialing

You can save 8 Speed Dial Numbers you often dial to positions titled
with number keys from “2” to “9” respectively. Select ““Call Center > Call
settings > Advance Settings > Speed Dial > Set Number”, and then set
“Enable Speed Dial” on. In the st andby mode, press and hold one of the
number keys from “2” to “9” until the call is started.

Adjusting the Sound Volume

During a call, you can press the Up/Down Key to adjust the earpiece
volume.

Answering Calls

1. To answer an incoming call, press Pick up K ey or left soft key.

2. To end or reject an incoming/ongoing call, press Hang up Key.

Options in Call

Your phone provides a number of functions that you can use during a
call.
During a call, you can access Hold/End single call, New Call, Phone
Book, Message center, Sound Recorder and other functions.

17

GUIDE TO MENU OPERATIONS

All function about the mobile phone are listed as below with brief
descriptions.

Phone Book

You can save many phone numbers in your mobile phone. The capacity
of your SIM card decides how many phone numbers can be saved in
the SIM card. You can access the Phone Book to search all records
saved in this mobile phone and your SIM card.

Quick Search

You c an quickly locate the number of the person you want to contact.
Please enter the initial letter of the person’s name, it will display
therelated records in the middle of the screen. Please use the Up/Down
key to select the number as desired, and then press Pick Up Key to
make a call.

Search Contact

You can find the desired phone number from the phone book easily and
quickly. In the standby mode, press left soft key to access Menu >
Phone Book > Search contact. Please follow steps as described
below:

1. In the Name box, enter the letters of the name or initial letters of

the name.

2. Press left soft key to access Options > Search > Phone Book List,

and all related information of the desired contact will be listed.
Please use the Up/Down key to browse all entries, and then press
Pick Up Key to make a call.

3. Press OK key to access Entr y Options, and then you can perform

following operations for eac h entry:

 Call: Take the number to make a call.
 Send text message: Send messages to the selected number.

18

 Send multimedia message: Send MMS message to the

selected number.

 View: Check the record for t he selected number.
 Edit: Edit the selected entry.
 Delete: Delete the entry from the Phone Book.
 Copy: You can copy each entry from the SIM card to the phone

or from the phone to the SIM card. i.e. SIM to Phone Copy or
Phone to SIM Copy.

 Move: You can move each ent ry from t he SIM card t o the phone

or from the phone to the SIM card.

 Send vCard: Send your phone number by text message /

multimedia message or Save as file.

 Send by SMS: Send the entry by SMS.
Tip: Pressing one of the number keys from 2 to 9, will show
starting by the letter corresponding to the key you pressed For
example, in order to search for the record of someone whose name

starts with C, press the key 2 quickly f or 3 times, t he cursor will
skip to the first entry of the contacts whose names are initialized with
C.

Add New Contact

You c an add a new contact entry to t he Phone Book, both for the SIM
card and your phone. Steps described as below:

1. From the P hone Book menu, press left soft key to sel ect Add New

Entry> To Master SIM/To Slave SIM/To Phone.

2. If the To Master SIM/ To Slave SIM is selected, press the left key to

select OK to start editing the contact names and phone number.

3. If the To Phone is selected, you can add the contact’s name, phone

number, home number, company name, email address, office

number, fax number, birthday and so on.
Tip: This mobile phone offers you several input methods, such as
Multitap A BC (ABC), Multitap abc ( abc), Numeric (123), Smart ABC (eZi

19

ABC), Smart abc (eZi abc) and so on. Please refer to “Appendix A:
Guidance of Entry Methods” for more details.

C opy A ll

This function enable you copy all entries both from the SIM card and the
phone.
Note: If the capacity of this phone book is different from the SIM card's,
the copy content takes the smaller one as standard.

Move All

This function enables you move all entries from the SIM card or the
phone.

Delete

You can s elect delete entries form the SIM card, the Phone or one by
one.

Caller Groups

You can set group name, caller ringtone, caller picture, and members
for different caller group.

Extra Number

You can set Master/Slave SIM Owner Number, Master/Slave SIM
Service dialing number, and SOS Number.
 Master/Slave SIM Owner Number: You can enter 2 groups of a

number and a name and can also edit or erase it.
 Master/Slave SIM Service dialing number: You can enter Service

dialing number.

 SOS Number: You can enter five groups of SOS numbers.

Note: If the keypad is locked, you can dial SOS numbers that you edit.

Phone Book Backup

This application allows easy transfer and backup of contacts stored in
your phone/SIM. It supports import and export of VCF files.

Phonebook Settings

 Memory status: display the occupied storage and the total storage.

20

 Preferred Storage: select the SIM or Phone as the preferred storage

for the new number.

 Fields: select the desired option when you add a new number.
 My vCard: can edit and send my card.
 Vcard Version: You can set Vcard 2.1 or Vcard 3.0.
 Human Voice Prompt: You can set On or Off.

Caller Picture/ Ring Tone

 To New contact: select the picture to the new entry.
 To Selected contact: select the picture to the selected entry.
 To Caller Group: select the picture to the caller group.

Messages

Text Message

Short Message Service (SMS) is a kind of network servic e. Your home
network may not support the service. Please consult your home
network operator for more information.

1. Enter the Menu, and select Messages.

2. Press the left soft key to enter the function.

Write Message

1. Please press the # key to switch input methods while editing a

message. You can enter letters and numbers, and insert pictures

and rings. (Support EMS service)

2. Edit your message, and press the * key to insert special s ymbols .

3. Select Options, and then you can do: Master/ Slave SIM Done, Use

Templates, Insert Obj ect and so on.

4. When you select Master/ Slave SIM Done, you can send or save as

desired.

Inbox

The icon

means an unread message or the message box is full.
You would not receive new messages once the message box is full.
Please delete unnecessary messages.

21

1. Select the unread message, and press the left soft key to read.

2. Select Options, and then you can reply, delete, forward and so on.

Outbox

The screen will display the message list once you select the Outbox.

1. Select “OK” to read the current messages.

2. Select Options, and then you can send, edit or select other

operations.

Templates

You mobile phone saves many messages in common use. You can edit,
remove or write message.

SMS Settings

You can set the default information about SMS properties.

Schedule SMS

Press the left soft key to access th e Add or Options > Add, and then you
can set the date, time, and message and Phone number. Press Done
and Save the message will sent out the message to the number as your
desire.

Note: The time format of this function is 24 hours.

MMS

Please consult your network operator to obtain the MMS services.

Write Message

While writing messages, you can select To, Cc, Bcc, Subject or Edit
content.

 To: You can enter the phone number or E-mail address..
 Cc: send t he MMS to others at the same time. You can enter phone

numbers or E-mail addresses.Bcc: send the MMS to others secretly
at the same time. You can enter phone numbers or E-mail
addresses ..

 Subject: edit the Subject of the MMS.
 Edit content: enter the text or add picture, audio and so on.

Inbox

The phone saves the received MMS into the inbox.

22

All received Messages display in the inbox, and the ic on m eans t he
MMS is unread. Use the Down/Up key to sc roll the cursor to check the
list, and the sender's name and number will display. If the MMS has
been read, the icon will change to the read icon. Please press the left
soft key to access Options, and then you can view, reply, delete and
so on.

Outbox

In the Outbox, please select Options, and then you can send, or select
other operations.

Drafts

In the Drafts, please select Options, and then you can send, edit or
select other operations.

Templates

User defined: you can save many MMS in it.
Default: You mobile phone saves many MMS in it.
And what you can do for those MMS are View, Write Message and
Properties.

MMS Settings

Please follow steps described as below:

1. Compose: You can configure Creat ion Mode, best page time, auto

signature, signature.

2. Send: You can configure Validity period, Delivery Report, Read

Report, Priority, Slide T i ming, and Delivery Time.

3. Retrieve: You can configure Home Network, Roaming, Read Report,

and Delivery Report.

4. Filter: You can configure Anonymous and Advertisement.

5. Server Profile: You can select one profile fro m 7 Pro fi le s to a ctiv ate ,

edit, or delete.

6. Memory Status: You can check the Usage, Used space and Free

space.

Chat

Use this function to chat with the sender by sending messages.

23

 Chat Room Info: s elect one chat room to set My Nickname and

Destn. Number.

 Start New: enter words and start to chat with the preset number.

Voicemail Server

Scroll the Up/Down key to select Voicemail Server in the Messages
menu, and select OK to access Voicemail Server.

 Call Voicemail: You can hear messages in the voice mailbox.
 Edit: Input or modify the number of voice mailbox.

Note: This service is supplied by the network, such as the message
machine service. It enables the caller to leave messages when you
cannot or Do Not want to answer the incoming call. Your number for the
voice mailbox is saved in this phone. In standby mode, hold the number
key 1 to dial the number of the voice mailbox after the number is
configured. Please consult your network operator for m ore details.

Broadcast Message

This network service enables you to receive all kinds of text messages,
such as weather reports or transportation information. Until now, there
are several networks afford the service in this world. Please consult
your network operator for more reference.

 Receive Mode: Turn on or off the Cell Broadcast.
 Read Message: Sc rol l the Up/Down Key to select the message.
 Languages: Select the desired language to display the broadcast

message.
Note: Your network operator decides whether the language is
supported or not.

 Channel Settings: Yo u can choose Sel ect, Add, Edit or Delete to

receive the Broadcast information.

24

Call Center

In the standby mode, press left soft key to access Menu > Call Center.

Call history

Master /Slave SIM Missed Calls

With this function, you can check recent missed calls.
Scroll the Up/Down key to select a missed call.
Press OK key to access Missed Call Information, and you can
Delete, Save to Phone book, call, Edit and so on.

Master/Slave SIM Dialed Calls

With this function, you can check recent dialed calls. In this function,
you can Delete, Save to Phone Book, Call, Edit and so on.

Master/Slave SIM Received Calls

With this function, you can check recent received calls. In this function,
you can Delete, Save to Phone Book, Call, Edit and so on.

Delete Master/Slave SIM Call Log

You c an delete all records of missed calls, dialed calls or rec eived calls
with this function or Delete all folders drastic ally.

Master/Slave SIM Call Timers

 Last Call: The last call time can be checked.
 Dialed Calls: The total time for all dialed calls can be checked.
 Received Calls: The total time for all received calls can be checked.
 Reset All: Reset the counters.

Master/Slave SIM Call Cost

 Last Call Cost: You can check the cost of las t call.
 Total Cost: You can check the total cost of all calls.
 Reset Cost: You can modify the cost of cal l, and reset the cost to 0.

PIN2 code is required while modifying.

 Max Cost: You can check and modify the upper limit. PIN2 code is

required while modifying.

 Price Per Unit: You can check and modify the call rate. PI N2 code is

required while modifying.

25

Note: This function is related with the SIM card. Some SIM cards don't
support the function. PIN2 is provided from the network operator.
Please consult your network operator to obtain the number.

Master/Slave SIM Text message Counter

 Sent: You can check and clear the number of sent messages.
 Received: You can check and clear the number of received

messages.
Note: This function has nothing to do with the SIM c ard. The amount of
sent or received messages will not change even if you change the SIM
card.

Master/Slave SIM GPRS Counter

You can check or reset the Last Sent, Last Received, All Sent, All
Received and Reset Counter.

Call settings

Master SIM Call Setting

 Caller ID: You can select Set By Network, Hide ID or Send ID. The

default status is the Set by Network.

Note: Thi s f unct i on i s related with your network. Select Hide ID may

cause failure to dial. Please test the calling function is ok before you

enable Hide ID.
 Call W ait in g:

1> Activate: The mobile phone will connect to the network when

Call Wait is enabled. After a while, the network will take a
response by sending m essages to ensure your operation. If Call
Wait is enabled, the network will warn you. At the same time,
another incoming call number will display on the screen when
the first call is ongoing and a new call is coming.

2> Deactivate: If you cancel Call Waiting, the network would not

warn you when the first call is ongoing and a new call is coming.

3> Query Status: With this function, you can inquire about the

current status from the network.

26

 Call Divert: This function allows your phone to divert coming calls to

another phone.

1> Divert All Voice Calls: When this function is enabled, all coming

calls will be diverted to another phone. Set it On or Off, the
phone will connect to the network. After a while, the network will
take a response and tell you the result on operation.

2> Divert If Unreachable: When this function is enabled, the

coming call will be diverted to another phone number if the
phone is unreachable.

3> Divert If No Answer: When this func t i on is enabl ed, the c oming

call will be diverted to another phone number if there is no
answer in some time.

4> Divert If Busy: W hen this function is enabled, the coming call

will be diverted to another phone number if the phone number
you dialed is busy.

5> Divert All Data Calls: You can divert all data calls with the need

of your network operator's support.

6> Cancel All Divert: Use to cancel all diverting functions.
 Call Barring:
This function makes use of Call Barring to limit some selected calls.
When you configure this function, you should consult your network
operator for the password. If the password is wrong, the phone will
prompt the fault message. After the desired number is select ed, please
continue to select On or Off. After a while, the network will take a
response and tell you the result.

1> Outgoing Calls:

− All Calls: When this option is enabled, you cannot make any
calls.

− International Calls: When this option is enabled, you cannot
make any international calls.

27

− International Calls Except to Home PLMN: W hen this option
is enabled, you can only make local calls when you are abroad
or dial to the country in which the network provider is.

2> Incoming Calls:

− All Calls: When this option is enabled, you cannot make any
calls.

− When Roaming: When this option is enabled, you cannot
receive any incoming calls if you are out of reach of the network
service.

3> Cancel All: Cancel the call barring. It also needs the Call baring

password provided by the network operator.

4> Change Barring Password: Use to modify the Call baring

password. It needs to input the original password before you
modify.

 Line Switching: Switch to Line 1 or Line 2, the default is Line 1.

Note: If Line 2 is selected, making calls from Line 2 depends on the
network operator.

 Closed user group: Press the left soft key to a ccess Group List, and
then select Add to input the group's name. Press the left soft key to
select Done, and then add the number. Press the left key to finish.
Select Option to Edit, Add, Activate, Deactivate or Delete the existent
group.

Slave SIM Call Setting

 Caller ID: You can select Set By Network, Hide ID or Send ID. The

default status is the Set by Network.
Note: Thi s f unct i on i s rel ated with your network. Select Hide ID may
cause failure to dial. Please test the calling function i before you
enable Hide ID.

 Call W ait in g:

1> Activate: The mobile phone will connect to the network when

Call Wait is enabled. After a while, the network will take a
response by sending messages to ensure your operation. If Call

28

Wait is enabled, the network will warn you. At the same time,
another coming call number will display on the screen when the
first call is ongoing and a new call is coming.

2> Deactivate: If you cancel Call Waiting, the network would not

warn you when the first call is ongoing and a new call is coming.

3> Query Status: With this function, you can inquire about the

current status from the network.

 Call Divert: This function allows your phone to divert coming calls to

another phone.

1> Divert All Voice Calls: When this function is enabled, all

incoming calls will be diverted to another phone. Set it On or Off,
the phone will connect to the network. After a while, the network
will take a response and tell you the result on operation.

2> Divert If Unreachable: When this function is enabled, the

coming call will be diverted to another phone number if the
phone is unreachable.

3> Divert If No Answer: When this function is enabled, the coming

call will be diverted to another phone number if there is no
answer in some time.

4> Divert If Bu sy: W hen this function is enabled, the coming c all

will be diverted to another phone number if the phone number
you dialed is busing.

5> Divert All Data Calls: You can divert all data calls with the need

of your network operator's support.

6> Cancel All Divert: Use to cancel all diverting functions.
 Call Barring:
This function makes use of Call Barring to limit some selected calls.
When you configure this function, you should consult your network
operator for the password. If the password is wrong, the phone will
prompt the fault message. After the desired number is select ed, please
continue to select On or Off. After a while, the network will take a
response and tell you the result.

29

1> Outgoing Calls:

− All Calls: When this option is enabled, you cannot make any
calls.

− International Calls: When this option is enabled, you cannot
make any international calls.

− International Calls Except to Home PLMN: When this option
is enabled, you can only make local calls when you are abroad
or dial to the country in which the network provider is.

2> Incoming Calls:

− All Calls: When this option is enabled, you cannot make any
calls.

− When Roaming: When this option is enabled, you cannot
receive any incoming calls if you are out of reach of the network
service.

3> Cancel All: Cancel the call barring. It also needs the Call baring

password which is provided by the network operator.

4> Change Barring Password: Use to modify the Call baring

password. It needs to input the original password before you
modify.

 Line Switching: Switch to Line 1 or Line 2, the default is Line 1.

Note: If Line 2 is selected, making calls from Line 2 depends on the
network operator.

Advance settings

1) Auto Redial

You c an set the Auto Redial function On or Off. When you activateauto
redial, the phone will automatically redial the last called number after a
while if you fail to connect t o the number. The time for auto redial is up
to 10 times. You cannot make any other calls when the Auto Redial is in
process. Press Cancel to end Auto Redial.

30

2) Speed Dial

Set the status on, and then you can set 8 groups for the speed dial.
(Corresponding number keys are 2 to 9). In the standby mode, press
and hold the number key to dial the corresponding number.

3) Call Time Display: You can set Call Time Display On or Off. The call
time will display when it is activated, .The call time would not display
when it is deactivated.

4) Call Time Reminder: In order to save the call cost, this function
prompts you to end the call in time. You can select Off, Single, or
Periodic. There is no prompt when Off is selected. You should enter a
specific time between 1 and 3000 seconds when Single is selected.
The phone will ring once when the time is up. You should enter a
specific time between 30 and 60 seconds when Periodic is selected.
The phone will ring once automatically at the specific time before the
integral minute is up.

Settings

In the standby mode, press left soft key to access Menu > Settings.

Dual SIM Setting

You can choos e one mode as your desire.

Phone Setup

Time and Date

 Set Home City: Select the desired home city.
 Set Time / Date: Enter the current time and date.
 Set Format: Select a time and a date format.

Schedule Power On / Off

You can set the time for auto power on /off. Do turn the status on before
using that function, and then the time.
Note: Please disable the Schedule Power On function before you board
an airplane.

31

Language

Select the desired language for the display text. In S-4580 you can
select 4 language options English, Hindi, Bengali, T elgu

Pref. Input Methods
Select the desired input method for the default input method.
Greeting Text

Set On, input words as your greeting text once you switch on the
phone .

Shortcuts

You can set shortcuts for those functions you often use.

Dedicated key

You c an configure short cut functions f or the Up, Down, Left and Right
key respectively. In the standby mode, press any one of them to access
the appointed function.

Auto update of date and time

It can be set to On or Off.

UART setup

When using this phone for GPRS , select different UART port to decide
whether Master /Slave SIM to be used.

Note: S-4580 dosen’t support phone as a modem, and USB Mass
Storage feature..

Misc. Settings

LCD backlight: You can set the LCD backlight.

Display Characteristic

With this function you can configure the basic status of display
characteristics including Wallpaper, Screen saver, Power On Display,
Power Off Display, Main menu st yle, S how date and tim e, Show owner
number, Keypad light setting.

Network Setup

Please contact the network operator for the following network service.

32

Master/Slave SIM Network setup

1. Network Selection
You can choose Automatic or Manual to select the network (Auto is
recommended). When you select Automatic, the phone will make the
preferential selection according to the network where the SIM card
belongs. When you select Manual, you are required to select the same
network as the registered network with the network operator by SIM
card for your use.

2. Preferences
Select the Preferred Networks. The default network is the network
where the SIM card belongs. Select Options to perform the following
operations:

 Add From List: Display all PLMN list.
 New: Create a new network and set the network priority.
 Change Priority: Reset the selected Network Priority .
 Delete: Delete the current preferred net work.

Security Setup

Master SIM Security Setup

 Master SIM Lock:
It is asked to input the PIN. It can be configured if the PIN is correct. If
SIM card is set on, it needs to input the PIN every time you power on. If
you enter incorrect PIN three times , it is asked to input PUK. PUK is
used to release and modify t he locked PIN. If PUK is not provided or
missed, please consult your network operator.
 Fixed Dial:
If thi s function is enabled, only pho ne numbers in the Fixed Dial List can
be dialed. PIN2 is required for this function. Network support is also
required.
Note: If you enter PIN2 after the phone is switched on, PIN2 is not
required before the phone is s witched off. Therefore, pleas e switc h the
phone off and switch it on again after configuration, if you do not want
others to change the status of the Fixed Dial.

33

 Barred Dial:
If this function is activated, the phone numbers in the barred dial list
cannot be dialed. PIN2 is required for the function. Network support is
also required.
 Change Password:
You can change Master SIM PIN1, Master SIM PIN2.
1> Mas t er SI M PIN1

− The original PIN is required before change the PIN.

− Enter the new PIN. 4-8 numbers can be used for PIN.

− Enter New PIN to ensure the New PIN.

2> Mas t er SI M PIN2

− The original PIN2 is required before change PIN2.

− Enter the new PIN2. 8 figures can be used for PIN2.

− Enter the New PIN2 again to ensure the new PIN2.

Slave SIM Secur ity Setup

 Slave SIM Lock:
It i s ask ed t o input the PIN. It can be configured if the PIN is correct. If
SIM card is set on, it needs to input the PIN every time you power on. If
you enter wrong PIN three times , it is asked to input PUK. PUK is used
to release and modify the locked PIN. If PUK is not provided or missed,
please consult your network operator.
 Fixed Dial:
If this function is enabled, only phone numbers in the Fixed Dial List can
be dialed. PIN2 is required for this function. Network support is also
required.
Note: If you enter PIN2 after the phone is switched on, PIN2 is not
required before the phone is s witched off. Therefore, please switch off
the phone and switch it on again after configuration, if you do not want
others to change the status of the Fixed Dial.
 Change Password:
You can change Slave SIM PIN and Slave SIM PIN2.
1> Slave SIM PIN

34

− The original PIN is required before changing the PIN.

− Enter the new PIN. 4-8 numbers can be used for PIN.

− Enter New PIN to ensure the New PIN.

2> Slave SIM PIN2

− The original PIN2 is required before changing PIN2.

− Enter the new PIN2. 8 figures can be used for PIN2.

− Enter the New PIN2 again to ensure the new PIN2.

Phone Lock

You can lock or unlock the phone. Enter the password to activate or
deactivate the phone lock. When the phone is locked, you will be
required to enter the phone password. 4-8 numbers can be used for the
phone password. The default phone password is 1122.

Auto Keypad Lock

You can lock/unlock the phone keyboard and set the Key Lock Time
to None, 5 sec, 30 sec, 1 min, and 5 min.

Change Password

You can change phone password and Tracker Password.

1> Phone Password

− The current phone password is required before changing the
phone password.

− Enter the new phone password.

− Enter the new phone password again to ensure t he new phone

password.

2> Tracker Password

− The current Tracker password is required before changing the
Tracker password.

− Enter the new T racker pa ssword.

− Enter the new Tracker password again to ensure the new

Tracker password.

35

Restore Factory Settings

Access Settings to select Restore Factory Settings, and press OK.
All settings can be restored to factory settings with this function. The
default password is 1122.

36

Media Center

Audio Player

The Play, Stop, Back, Forward functi ons correspond to the Up, Down,
Left and Right Key respectively. The available music formats. Select
List to access the Play List, and then select Options to perform the
following functions: pl ay, details, add to rings, refresh list, settings.
Note: The Audio Player of the phone will automatic ally play music files
from the My Music folder. You may need to refresh it manually from the
settings in case you have earlier opted for manual refresh settings.
Warning: Make sure that the volume is appropriate for your hearing
while using the audio player.

Sound Recorder

The mobile phone supports WAV, AMR recording formats. You can
record conversations, which may be saved to the Audio folder under
File Manag er. If there is a record, press left soft key you can do: Play,
Append (only for amr), Rename, Delete, Delete All files, Use As and
Send.
Note: If a call is incoming while recording, the record will abort and the
data will be paused. AMR adopts dynamic compress ion and provides a
longer recording time than WAV‘s while utilizing the same storage
space.

FM Radio

You can us e your phone to listen to FM radio stations once the original
Headset is plugged into the accessories connector. Select FM Radi o in
the Menu to access the radio controls.

 Press the Up key to Power on/ off the FM radio.
 Press the Left/Right key to step down/up to the next frequency.

 Press the “

*”/”#” key to adjust radio volume.

 Press Options to access the following options: channel list, manual

input and so on.

37

Tip: Long press of the Numeric key 0 in idle screen activates the FM
function.

Schedule FM Record

With this function, your phone can record the FM program as the
schedules once the original Headset is plugged into the accessories
connector. You can set On/Off, the date and tim e, repeat style, c hannel
settings and record settings.

Melody Composer

The mobile phone enables you to compose your favorite music as the
tune of the incoming call, alarm.
Note: The phone can save multiple tones edited by you according to
the volume of tones.
When the Tune Editing List is blank, you can edit your favorite tunes by
pressing “Add”. After you have finished edi ting, press Options to select
a music instrument or playing speed to play the editing tunes. You also
can save the editing tunes.
Select the edited music, and press Options to perform the following
operations:

− Play: You can play the specified self-edit tunes.

− Edit: You can edit the specified self-edit tunes.

− Add: You can add new self-edit tunes.

Note: A maximum of 150 notes can be edited with a piece of
self-edit tune.

− Rename: You can modify the name of the selected self-edit tune.

− Delete: You can delete t he selected s elf-edit tune.

− Dele t e All Files: You can delete all self-edit tunes.

− Use A s: You can send the self-edit t ones to User Profile.

− Send: You can send the self-edit tones to Text Message and

Multimedia Message.
In the window of Tone Editing, press Options to perform the following
operations:

38

− Play: You can preview the edited tone.

− Play Speed: You can set the playing speed of the current editing

tone.

− Select Instrument: You can select the music instrument playing

the tone.

− Save: You can save the tone.
The rules by which the tone is composed as follows:
0: Insert one pause;
1: Insert Do;
2: Insert Re;
3: Insert Mi;
4: Insert Fa;
5: Insert So;
6: Insert La;
7: Insert Si;
8: Insert a vibration note;
9: Insert a backlight;
*: Modify the playing rhythm of the current tone;
#: Modify the current note with halftone;

↑: Modify the tone of current note (high, middle, low);
↓: Modify the tone of current note (high, middle, low).

File Manager

You can use the function to manage all types of files saved in the Phone
or Memory card.

1. There are all of files saved in your phone. Press Options you can
select Open, New Folder, Format, Rename (only for the T-Flash card
option), and Details (only for the T-Flash card option).

2. If the specified one is” Folder”, Press Options you can select Open,
New Folder, Rename, Delete or Sort by.

3. Press Option if the specified item is a file. For different kinds, pres s
Options you can select View (Play), Use, Send, Detail, Rename, Copy
or other options.

39

User profiles

Normal

1. Activate

2. Customize

 Tone Setup: Includes Master/Slave SIM Incoming Call, Power on,

Power off, Master/Slave SIM Message Tone, Human Voice Tone1.
You can select built-in ring tunes, or the tunes composed by
yourself.

 Volume: Includes the volume setting of Ring Tone and Key Tone.

The volume degree is from 1 to 7.

 Alert Type:

− Ring: Just ringing, no vibration.

− Light Only: Just light, no ringing.

 Intell ige n t Call Alert: You can set On or Off.
 Ring Type:

− Single: Rings once when a call is coming.

− Repeat: Rings continuously when a call is coming.

− Ascending: Rings continuously and the volume increases

gradually.

 Extra Tone:

− Warning: If necessary, you will be warned by the prompt tone.

− Error: You will be warned by a tone if you make a mistake.

− Camp On: A prompt tone will be heard after searching the

network successfully.

− Connect: A prompt tone will be heard after getting through to the
dialed number.

 Answer Mode:

− Any Key: Press any key to answer a call (Except of Hang Up
Key and Right Soft Key).

Silent

Please refer to “Normal” for more details.

40

Note: Press and hold the # key to enable or cancel the silent mode.

Outdoor

Please refer to “Normal” for more details.

Indoor

Please refer to “Normal” for more details.

Headset

Insert the earphone and acc ess the Headset mode automatically. This
mode has no Activate option. Please refer to “Normal” for more details.

Organizer

Calendar

You can view and edit the memo of a specified date with this function.

1. View Tasks: You can view or edit the daily arrangement of the
day.

2. View All: You can view or edit all the daily arrangement of the
day.

3. Add Event: You can select task types: Reminder, Meeting,
Course.

4. Delete Event: You can select delete entries form All, Overdue,
Spec Period.

5. Jump to Date: Skip to the specified date to view or edit the daily
arrangements of the day.

6. Go To Weekly/Monthly View: Go t o the specified date to check
which week/Month it is.

7. Indian Calendar: You can view or edit: Tithi details, Festival list,
Date to tithi, Yearly tithi.

8. Onscreen Display: It can be set to None or I ndi an.

41

Tasks

You can View, Add, Edit, Delete, Delete Overdue, Delete All, Send
Vcalendar and Save As File as desired. Start up the Tasks and press
OK. Press Add to acc ess to add a new memo.

Alarm

The mobile phone provides 5 alarms and you can set them as your
need. If you have configured an alarm, an icon indic ated that you have
configured the alarm will appear. No icon will show if you don’t set an
alarm. Select “Edit” to set the current alarm.

Calculator

The calculator can add, subtract, multiply and divide. To use the
calculator:

1. Press the # key to enter the decimal point

2. Press the up, down, left and right key and OK key to select ＋, －, ×,

÷, ＝ respectively.

3. Press Clear to delete the figure.

Units Converter

You can make the units conversion for weight and length. Enter the
number into the column, and then press “OK” to get the result.

Currency Converter

You can make currency conversions. Press OK after enter the
exchange rate, and then enter the number of the currency, and press

OK to get the result.

Stopwatch

The stopwatch has two modes - Split Timing and Lap Timing, and you
can view the records of both the modes.

World Clock

Scroll to browse every city’s time zones in the world map. The related
date and time will display at the bottom of the screen.

42

Health

Provides the reference of body mass index(height, weight and sex).

Services

STK Service

This service is offered as the SIM card service provided by the network
operator.

WAP

WAP enable you tour around the Internet world easily and pleasantly.
Please follow the steps described as below:

1. Homepage: The default Internet Web Address.

2. Bookmarks: Save the Web address you often use.

3. Recent Pages: Records after you browse the Website.

4. Offline Pages: You can view offline pages which you saved.

5. Input Address: Press the left soft key to access Enter Address, an d

then input the web address to go to the Internet.

6. Service Inbox: Messages sent to users from the Web site.

7. Settings: You can configure Select SIM, Edit Profile, Browser

Options, Service Message Settings, Clear Cache, Clear Cookies
and Tru sted Certificates.

Data Account

Press the left soft key to perform following steps:

1. GSM Data: Edit the GSM account.

2. GPRS: Edit the GPRS account.

Conn. Management:

You could check the status of network connection.

43

Fun Spice

The newly launched Fun corner from Spice Mobiles for its customers.

SpiceGang

It is a wap port al fro m w here user can dow nload Ringtones, Wallpapers,
Animations, Videos and other kind of content.

Step1: Check the GPRS settings for your operator.
Step2: Initiate SpiceGang wap portal to browse and download the

content.
Step3: Charges for download apply as per operator pricing.
Explore the whole world of Entertainment with SpiceGang.

Reuters

Reuters India gives you the latest India, World and Business news and
more. Also, get the latest stock market i nformation along with tools like
the currency converter and weather in your city on your mobile phone.
NOTE: Please ensure that you have GPRS settings in your phone to
open Reuters. Contact your operator for GPRS settings.

Ibibo

Now connect with the ibibo community on Spice Mobiles. Go and cre ate
your profile, search for people based on their age, sex & location, make
new friends and send or receive blurbs. Invite your existing friends to
join your new community.
The services pre loaded on Spice Phones are Cool Stuff, Cricket
Update, Free SMS, and Make New Friends.
Please check your GPRS settings before accessing Ibibo.

Voice Zone

Sangeet

Spice Mobiles presents Sangeet Portal – One Touch Access to the
huge library of songs comprising of 17 languages and over 1 lakh
tracks!
Sangeet is a third party application. Use of it is at your sole discretion.
Spice Mobiles disclaims all responsibilities from its usage, whether

44

express or implied. The IVR codes are owned and provided by third
party and may change without prior notice.

Bhakti Sangeet

Spice Mobiles present Bhakti Sangeet on IVR. Use this portal to listen
to your favorite devotional songs at the click of a button, virtually,
anytime and from anywhere.
Bhakti Sangeet is a third party application. Use of it is at your sole
discretion. Spice Mobiles disclaims all responsibilities from its usage,
whether express or impl i ed. The IVR c odes are owned and provide d by
third party and may change without prior notice.

Suno Sunao

Spice Mobiles brings SUNO SUNAO to its customers. It gives the
anonymity, thrill, excitement and above that a chance to speak and
listen to the Chat friend!
SUNO SUNAO is a third party application. Use of it is at your sole
discretion. Spice Mobiles disclaims all responsibilities from its usage,
whether express or impl i ed. The IVR codes are owned and provided by
third party and may change without prior notice.

Popat

After select, you have the following options:

1. Human Voice Prompt: You can set On or Off. With this function
you can listen any stored no. in the Phone Book.

2. Intelligent Call A l ert: You can set On or Off. With this function you
can listen the no. of incoming call.

3. Human Voice tone1: You can On or Off. With this function you can
activate the voice tone for keypad.

MGurujee

MGurujee is India's leading M-Learning portal delivering unique anytime
anywhere mobile phone based learning experience with access to a
wide variety of quality knowledge content from market leaders.
NOTE: Please check your GPRS settings bef ore acc essing MGurujee.

45

Email2SMS

Emergic Email2SMS is a product of Netcore Solutions Pvt. Ltd.
provided by Spice Mobiles. Email2SMS allows you to receive email on
your phone via SMS without GPRS. You can Read, Reply, Compose
and Forward your emails via SMS. This service is only available for
Gmail, Indiatimes and Corporat e Account Hol ders. Spice Mobiles offers
FREE subscription for one month.

1. Just send SPICE START <Location> to 575758 to register for

Email2SMS serv ice.
For composing new mail type NEW <Receiver's Email-Id> S: <Subject>
B: <Message> and send it to 575758.

2. For replying to any mail types REPL Y <Message-Id> <Message> and

send it to 575758.

3. For replying to all in the mail type REPLY <Message-Id> <Message>

and send it to 575758.

4. For forwarding the mail type FWD <Message-Id> <Receiver's

Email-Id> <Message> and send it to 575758.

5. For reading the remaining part of mail types READ <Message-Id>

and send it to 575758.
NOTE: Message-Id is the number which you get at the end of SMS. i.e.,
01, 02, 03, 04.

For more details contact Customer Support:
Phone: [phone],

Email: [email protected],
Chat ID: [email protected], [email protected],

[email protected]
Disclaimer: For any Third Party application, Spice Mobiles disclaims all
responsibiliti es from its usage, whether express or implied.

Dazzle Ringtone

Abb Har Bar Naya Gana Bajega! You like lot of songs and also like to
set those all songs to be a ring tone of your mobile phone?? For this

46

you have to change ring tone every time with new song.
Not anymore. M-4580 gives you the facility of Dazzle/Shuffle Ringtones.
Where you can set up to 10 songs in one time as your ring tone.
Now whenever a new call will come every time a new song will play as
your ring tone.

Games

There are several interesting games in the phone. Please refer to
instructions from the game menu for more details.
Tip: The game menu includes Start Game, Game Level, Best Grades
and Game Help.

Others

B/W List

1） White list: you can set 20 numbers. When this white list is

enabled, you can but receive the calls from the numbers entered in
the white list.

2） Black list: you can set 20 numbers. When this Black list is

enabled, you would not receive the calls from the numbers entered
in the Blacklist.

Mobile Tracker

Now be sure of your mobile phones with Mobile Tracker offered by
Spice Mobiles. This feature allows users to track their phone if they are
lost or stolen. Switch on Mobile Tracker application and whenever a
new SIM is inserted in your phone you will receive a SMS on pre
defined numbers.

1) Tracker Mode

This function requires your network support. You can set ON or OFF.
When the function ON and the phone change a SIM card, the phone will
sent a message to t he number which you set in Fun Spice > Other >
Mobile Tracker > Tracker Number. The message will tell you that
which number is using your phone now. The default password is 1122.

2) Tracker Number

47

You can set Tracker number.
TIP: This function requires your network support. When you set Tracker
Mode OFF, and then you can set the tracker number you want.

Private Menu

Did some one scan your Personal Mess ages when you were out? Get
smarter with M-4580's Private Menu advantage. Keep your Phone
numbers, SMS and Call Records password protected so that no one
gets to know your secrets. Can Keep 500 Numbers of Phone Book,
SMS up to 200, 20 each of Dialed Calls, Received Calls and Missed
Call Records, your personal notes like different passwords, account nos.
etc (Above all are shared between both Private and Non-private Menu
and for SMS with SIM Card SMS and handset SMS)

48

IMPORTANT INFORMATION

Use of Passwords

Your mobile phone and SIM card have various passwords. Those
passwords avoid unauthorized use of your phone and SIM card. You
can change PIN, PIN2 and phone password in the “Setti ngs > Security
Setup > Change Password”.

Phone Code

The Phone code can be used to avoid unauthori zed us e of your phone.
The factory setting for the phone code is 1122. If phone lock is enabled,
you will be asked to input the phone password when you switch on your
phone.

PIN (4 to 8 digits)

The PIN (Personal Identification Number) code protects your SIM card
from unauthorized use. The PIN code is usually supplied with the SIM
card. When the PIN code request is enabled, the password is asked
every time the phone is turned on.
If you enter incorrect PIN three tim es t, the SIM card will be lock ed and
you will need to use the PUK to unlock it. PUK is usually set by the
network operator.

1. Enter the correct PUK to unlock the SIM card, and then enter the

new PIN and press OK.

2. If you are prompted t o enter the new PIN again, enter it and press

OK.

3. If the PUK is correct, the SIM card will be unlocked and the PIN will

be reset.

PUK (8 digits)

The PUK (Personal Unblocking Key) code is required to change a
blocked PIN code. Please contact your network operator for the code.
Note: If you enter wrong PUK ten times,, the SIM card will be invalid.
Consult with your network operator for a new SIM card.

49

PIN2 (4 to 8 digits)

The PIN2 code, supplied with some SIM card, is used for some
functions, such as Call Cost , Fixed Dial and so on. Please c onsult your
network operator to confirm whether your SIM card supports those
services or not.
Three times wrong PIN2 code input, the SIM card will be locked and
you will need to use the PUK2 to unlock it.

1. Enter the correct PUK2 to unlock PIN2, and then enter the new PIN2

and press OK.

2. If you are prompted to enter the new PIN2 again, enter it and press

OK.

PUK2 (8 digits)

The PUK2 code, supplied with some SIM card, is required t o change a
blocked PIN2 code. It may be supplied with the SIM card. If not, contact
your network operator.
Note: If you enter wrong PUK2 ten times,, the SIM card will be i nvalid.
Consult with your network operator for a new SIM card.

Barring Code

To activate call barring, you need a Barring Code. You obtain the
password from your service provider.

Battery I n fo rmation

Charing and Discharging

 The charger is designed to be used in temperatures between 0° C to

40°C.

 Do not charge the phone in wet and damp conditions.
 Use only batteries approved by the phone manufacturer and

recharge your battery only with the charges approved by the
manufacturer.

 We strive to produce products in compliance with global

environmental standards

50

 The charger meets the standard for safety of information technology

equipment and office equipment use. It must be used for this
purpose only.

 Your phone i s powered by a rechargeable battery. Full performance

of the battery is achieved only after two or three complete charge
and discharge cycles.

 When the battery level is low, “Low Battery” will be displayed on the

LCD screen. If you have selected Alert Tone (Warning Tone of any
profile in Profiles), t he phone will sound the alert tone.

 When a charger is not in use, disconnec t it from the power source.

Do not leave the battery connected to a charger for longer than 12
hours, since overcharging may shorten its life.

 Temperature extremes will affect the ability of your battery to charge.

Tips for Battery

 Placing the battery in hot or col d places, such as in a closed car in

summer or winter, will reduce the capacity and lifetime of the battery.

 Do not let the metal contacts on the battery touch another metal

contact. It could short-circuit and damage the battery. Use the
battery only for its intended purpose.

 Do not disassemble or modify the battery by yourself.
 Do not clean the battery with water or any organic solvent.
 Always keep the battery dry.
 The battery can be charged and discharged many times but it will

wear out as last. When the tal k and standby time is obviously shorter
than normal, please change the original battery approved by
manufacturer.

 Do not short-circuit the battery.
 Turn off mobile phone before removing the battery.
 Do not dispose of batteries in fire.
 If you smell anything strange from the battery or find that the battery

is overheated, you should stop using it immediately and contact the
authorized After Service Center in your region.

51

 If you don’t use the battery for a long time, please fully charge the

battery before you store it.

Batteries should never be placed in municipal waste. Batteries

must be recycled or disposed of properly. Please follow local
regulations for disposal of batteries .

Usage & Maintenance

To keep your product working well, take a moment to review the
following usage & maintenance tips, which will help you to fulfill any
warranty obligations and to enjoy this product for m any years.
 Keep your phone and all its parts and accessories out of children’s

reach.

 Your products are not water-resistant. Keep it dry. Precipitation,

humidity and liquids contain minerals that will corrode the
connectors.

 Always treat your products with care and keep it in a clean and

dust-free place.

 Do not expose your product to extreme high or low temperatures.

Your phone operates best in temperature between 15 °C and 25°C.
Minimum and maximum temperatures recommended by the
manufacturer are -10°C and 55°C.

 Do not expose your product to open flames or lit tobacco products.
 Do not attempt to disassemble or modify your product.
 Do not drop, throw or try to bend your product.
 Do not paint your product.
 Do not use harsh chemicals, cleaning solvents, or strong detergents

to clean it.

 Do not keep any magnetic thing, like credit cards, near your

product.

 If you find that the battery has any crack, deformation or anything

else, you should stop using the battery immediately.

 If the electrolyte leak out and contact your skin or clothes, you

should immediately use soap and clean water to clean it. In case the

52

electrolyte s patters into your eyes, you must use the clean water to
wash your eyes thoroughly and go to the hospital immediatel y.

 If your phone or any accessory doesn’t function normally, please

send them to the nearest authorized service facility. The qualified
personnel will assist you, and if necessary, arrange for service.

Emergency Call s

This phone, like any wireless phones, operates using radio signals,
wireless and landline networks which cannot guarantee connection in
all conditions. Therefore, you should never rely solely upon any
wireless phone for essential communications (e.g. medical
emergencies)
To make an emergency call:
1> Switch your phone on.

Some networks may require that a valid SIM card is properly
inserted in the phone

2> Dial the official emergency number. Emergency numbers vary by

location.
While making an emergency call, please remember to give all
information as particularly as possible. Never disconnect the call please
until you are given permission to do so.

53

APPENDIX

Appendix A: Guida n ce On Entry Methods

This phone provides several input methods which can be used in
editing the Phone Book, short messages, memos, greetings, alarms
and other text applications.

The Icons of Input Methods

After entering different kinds of edit windows (including edit phonebook,
short messages. etc.), the icons of input are as follows:

“123”: The Entry method of Numeric appears as: “123”
“ABC”: The entry method of Multitap ABC appears as: “ABC”
“abc”: The entry method of Mulitap abc appears as: “abc”
“eZi ABC”: The entry method of eZiTextSmart ABC appears as:

“eZi ABC”
“eZi abc”: The entry m ethod of eZi Text Smart abc appears as: “eZi
abc”

“

”：The entry method of Multitap Hindi appears as: “HI”

“

”：The entry method of Multitap Bengali appears as: “BE”

“

”：The entry method of Multitap Telugu appears as: “TE”

How to Switch Between the Input Methods

Press the # key to switch the input methods.
e.g.: If the current input is Smart ABC the screen will show “eZi ABC”.
Press the # key, to go to Smart abc, and the screen will show “eZi abc”.

Numeric, Multitap ABC and Multitap abc Input Methods

Numeric

When the icon of the input method is “123”, press the number keys to
enter the numbers directly.
Multitap ABC and Multitap abc

54

When the icon is “ABC” or “abc”, press the number keys（2 to 9）
repeatedly until desired letters appear in the text area. Press the

number key once for the first letter. Press twice for the second letter. So,
press number keys to reach the desired letter in the same way.
Press 0 key to enter a blank space or “0”.
Note: while using the Numeric entry, please switch to the method of
Multitap ABC and Multitap abc first if a blank space is required, and then
press 0 to enter a blank space.

How to Input Special Symbols

If you want to input speci al symbols, such as ". ! ? = < >”, Etc., please
following steps as below:
Press the * key to display the symbols. Press the Up/Down, or
Left/Right Key to move the cursor in the symbol table, and select one
symbol. Press the right soft key to cancel the symbols selection.

55

Appendix B: Troubleshooting

This section lists some problems that you might meet while using your
phone. If you feel that your phone do not operate normally, please reset
settings first, and then follow Troubleshooting Guide. If you are still
unable to solve problems, please contact t he aut horized s ervic e center
or the store from where you purchased the phone.

Proble

ms

Solutions

Can not
answer
or
make a
call

Make sure that the phone has been switched on.

Make sure that the battery is charge d.
Make sure that the signal intensity is high enough.
Make sure the own number function in the call setting is
system p reset or number s endi ng.

Make sure the line switch in call setting is the system

preset line. Check whether you have set up call barring or
fixed dialing or any other safety func t ion.

Check whether you have set up call diverts. Check
whether you have inserted the proper SIM card correctly.

Low
voice

Check if the volume has been set too low.

No ring

Check whether you have set up the” Light Only” option.

Check whether the ring volume is not too low
Move away from a noisy place to check if you can hear
the phone ringing.

Check whether you have set up call diverts.

LCD
unclear

Check whether the contrast has been set too low.

T-Flash
card
detect

slowly

Format your T -Flash card with your phone.

Note: To protect your files from getting lost, please

backup the important information into the safe place

before you formatting card.

56

Appendix C: Available Accessories

Dual Stereo Personal Hands Free Handset

The Dual Stereo Personal Hands Free Handset allows you listen to
music or to make conversations with hands free comfort.

Travel Charger

You can charge the phone with the Travel Charger when you are on the
move.
Note: Please use approved accessories to get the most out of your
phone.

Appendix D: FCC Statement

This device has been tested and found to comply with Part 15 of the
FCC rules. Performance is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

3. Changes or modifications not expressly approved by the

manufacturer or authorized service center could void the user’s
authority to operate this equipment.