Spellman MR Series Instruction Manual

R

MP SERIES

MODEL :
SERIAL# :
DATE :

SPELLMAN
HIGH VOLTAGE ELECTRONICS
CORPORATION

475 Wireless Blvd.
Hauppauge, New York, 11788

[phone]*FAX: [phone]*
E-mail: [e-mail]
Website: www.spellmanhv.com

High Voltage Power Supply

MP SERIES MANUAL 118050-001 Rev A

The MP Series has been designed as high performance
dc to dc converters with output voltages up to 40kV.

Each module provides well regulated, low ripple and
high stability high voltage in a highly versatile compact
design, combining linear and switched mode techniques
to minimize internal dissipation and generated EMI/RFI
interference. The higher voltage modules are vacuum
encapsulated to ensure corona free operation.

Specialist cell manufacture of the MP Series ensures
prompt delivery.

TYPICAL APPLICATIONS

Photomultiplier Tubes
Scintillators
Electron Guns
Ion Guns
Nuclear Instruments
Electrostatic lenses
Spectroscopy
Microchannel Plates

OPTIONS

F Flange Mounting
P Positive Output Polarity
N Negative Output Polarity
LL Optional Lead Length

• ARC AND SHORT-CIRCUIT PROTECTION

• LOW OUTPUT RIPPLE - 0.001% P-P

• LOCAL AND REMOTE VOLTAGE PROGRAMMING

• 10V REFERENCE OUTPUT FOR EXTERNAL CONTROL

• HIGH STABILITY 0.001% LINE AND LOAD REGULATION

• MODELS UP TO 40KV OUTPUT

• CE MARK FOR EMC DIRECTIVE

• OEM CUSTOMIZATION AVAILABLE

SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION

MP

10W HIGH STABILITY
POWER SUPPLY

PAGE 1 OF 2

SPECIFICATIONS

Input Voltage:

+24Vdc±2V. Other input voltages available on special order.

Input Current:

Less than 1A at full output.

Output Voltage:

Continuously adjustable over entire output range. Available
in either positive or negative output polarity. See table for
voltage ranges.

Output Voltage Control: Controlled by either:

1) Internal ten-turn potentiometer

2) External potentiometer 5k to 100k (set internal pot. to max.)

3) Remote differential voltage programming (0 to +10V gives
0 to full output).

Accuracy 0.1%.

Remote Control:

Remote programming Common Mode Range: -5VDC to +15VDC

Line Regulation:

0.001% for input change of 1V.

Load Regulation:

0.001% for 100µA to full load change

(at maximum voltage).

Temperature Coefficient:

Better than 25ppm/°C.

Stability:

<0.007%/hr at constant operating conditions
after 1 hour warm-up.

Output Voltage and Current Monitors:

Voltage: 0 to +10V represents zero to full output ±1%.
Current: 0 to +10V represents zero to full output ±2%.

Temperature:

Operating: 0°C to +50°C.
Storage: -35°C to +85°C.

Connectors:

Input: 10 pin connector (mating connector supplied).
Output: Output voltage 1-20kV: 500mm screened cable URM76

Output voltage 30kV: 500mm screened cable RG59

Output voltage 40kV: 500mm silicone rubber cable

USA [phone] FAX: [phone] e-mail: [e-mail]
UK [phone] FAX: [phone] e-mail: [e-mail]
JAPAN [phone] FAX: [phone] e-mail: [e-mail]
CHINA [phone] FAX: [phone] e-mail: [e-mail]

www.spellmanhv.com

128005-001 REV.B

MP SELECTION TABLE

OUTPUT MAX. RIPPLE MODEL
VOLTAGE CURRENT (full load)

kV mA mV

0 to 1 10 10mV p-p MP1*
0 to 1.5 6 10mV p-p MP1.5*
0 to 2 5 10mV p-p MP2*
0 to 2.5 4 10mV p-p MP2.5*
0 to 3 3 10mV p-p MP3*
0 to 5 2 20mV p-p MP5*
0 to 10 1 100mV p-p MP10*
0 to 15 0.60 150mV p-p MP15*
0 to 20 0.50 200mV p-p MP20*
0 to 30 0.33 300mV p-p MP30*
0 to 40 0.2 400mV p-p MP40*

MP CONNECTOR 10 PIN

TB1 SIGNAL TB1 SIGNAL

1 Synchronization 6 Remote Control
2 +24V Input 7 Vprog+
3 Voltage Monitor 8 Current Monitor
4 Local Control 9 Vprog­5 Remote / Local Link 10 Power Ground

SPELLMAN

HIGH VOLTAGE ELECTRONICS CORP.
Plain view, NY 11803 MADE IN USA

PART NO:
MODEL:

SERIAL NO.
OUTPUT:
INPUT:

11098

ANALOG INPUT

0 TO 10V

I MON 0 TO 10V

POWER OVSYNC

+24V

V MON 0 TO 10V

REMOTE

LINK

LOCAL

HV
ADJ

76

MP SERIES

5432

+ –

Mounting studs
M3 × 12
2 PL

D

3.19
[81]

3.86 [98]

1.65
[42]

0.28
[7]

2.76 [70]

0.55
[14]

SPELLMAN

HIGH VOLTAGE ELECTRONICS CORP.
Plain view, NY 11803 MADE IN USA

PART NO:
MODEL:

SERIAL NO.
OUTPUT:
INPUT:

11098

ANALOG INPUT

0 TO 10V

I MON 0 TO 10V

POWER OVSYNC

+24V

V MON 0 TO 10V

REMOTE

LINK

LOCAL

HV
ADJ

76

MP SERIES

FLANGE MOUNTING (optional)

5432

+ –

Mounting holes

0.130 [3.3] Dia.
4 PL

D

Fixing
Centers

0.43
[11]

0.24
[6]

2.09
[53]

2.99 [76]

Depth in.(mm)
1-5kV: 6.61(168)

10-15kV: 8.27(210)
20-30kV: 10-24(260)
40kV: 13.0(330)

SIDE VIEW

BOTTOM VIEW

STUD MOUNTING (standard)

SIDE VIEW

BOTTOM VIEW

Depth in.(mm)
1-5kV: 5.83(148)

10-15kV: 7.48(190)
20-30kV: 9.45(240)

TOP VIEW

TOP VIEW

*Specify “P” for positive polarity or “N” for negative polarity.

DIMENSIONS: in.[mm]

SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION

MP

10W HIGH STABILITY
POWER SUPPLY

PAGE 2 OF 2

Dimensions:
Stud mounted case

MP1 to MP5: 1.65”H x 3.86”W x 5.83”D (42mm x 98mm x 148mm)
MP10 to MP15: 1.65”H x 3.86”W x 7.48”D (42mm x 98mm x 190mm)
MP20 to MP30: 1.65”H x 3.86”W x 9.45”D (42mm x 98mm x 240mm)

Two M3 metric studs on case as standard
(mating hardware supplied)

Flange case

MP1 to MP5: 1.65”H x 3.86”W x 6.61” (42mm x 98mm x 168mm)

Fixing center: 6.14” (156mm)

MP10 to MP15: 1.65”H x 3.86”W x 8.27” (42mm x 98mm x 210mm)

Fixing center: 7.80” (198mm)

MP20 to MP30: 1.65”H x 3.86”W x 10.2” (42mm x 98mm x 260mm)

Fixing center: 9.77” (248mm)

MP40: 1.81”H x 3.86”W x 13.0” (46mm x 98mm x 330mm)

Fixing center: 12.5” (318mm)

(4 x 3.3mm mounting holes))

Weight:

MP1 to MP5: 21.18 oz. (600g)
MP10 to MP15: 35.3 oz. (1000g)
MP20 to MP30: 51.18 oz. (1450g)
MP40: 76.24 oz. (2160g)

USA [phone] FAX: [phone] e-mail: [e-mail]
UK [phone] FAX: [phone] e-mail: [e-mail]
JAPAN [phone] FAX: [phone] e-mail: [e-mail]
CHINA [phone] FAX: [phone] e-mail: [e-mail]

www.spellmanhv.com

128005-001 REV.B