Spellman 230 Series, Bertan 230 Series, Bertan 230-01R, Bertan 230-03R, Bertan 230-05R Instruction Manual

R

Instruction Manual

230 SERIES

Bench Top High Voltage Power Supply

SPELLMAN
HIGH VOLTAGE ELECTRONICS
CORPORATION
One Commerce Park
Valhalla, New York, 10595

[phone] * FAX: [phone]
E-mail: [e-mail]
Website: http://www.spellmanhv.com

230 Series User’s Manual 118127-001 Rev A

PAGE 1 OF 2

S PE L L M A N H I G H V O LTA G E E L E C T R O N I C S C O R P O R AT I O N

Spellman’s Bertan brand of 230 Series high voltage power
supplies provide regulated high voltage outputs from 1 to
30kV. The low noise, linear topology employed results in
extremely low output ripple specifications. These 12 to 15
watt units are inherently reversible by design, providing
either positive or negative output polarity. The 230 Series is
fully arc and short circuit protected. Excellent regulation
specifications are featured along with outstanding stability
performance.

TYPICAL APPLICATIONS

HiPot Testing
Electrostatics
General Laboratory Usage

SPECIFICATIONS

Input Voltage:

115Vac, ±10%, 50/60 Hertz @ 0.5 amp
230Vac, ±10%, 50/60 Hertz @ 0.25 amps
Input voltage is switch selectable

Output Voltage:

See “model selection” table

Output Polarity:

All units are reversible polarity by design

Output Current:

See “model selection” table

Voltage Regulation:

Line: ≤0.002% of rated output voltage over specified

input voltage range

Load:≤0.005% of rated output voltage for a full load

change

Current Regulation:

Internally set to limit at less than 125% of rated current.
A rear panel switch allows limiting at 25% of rated full current.

Ripple:

See “model selection” table

Temperature Coefficient:

≤100ppm/°C

Stability:

≤0.01%/hour, 0.02% per 8 hours after a 1/2 hour warm up

Accuracy:

Front panel control: ±(0.2% of setting + 0.2% of maximum)
Front panel Meter: Voltage ±(0.5% of setting + 0.5% of

maximum), Current ±(2% of setting + 0.5% of maximum)
Remote Programming: ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor: ±(0.1% of reading + 0.1% of maximum)
Current Monitor: ±(2% of reading + 1% of maximum)

Front Panel Metering and Controls:

Power ON/OFF switch

3.5 digit metering for voltage and current, switch selectable
Polarity indicator
10 turn locking potentiometer to set output voltage
HV output connector
Ground stud

Operating Temperature

0°C to +50°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Input Line Connector:

IEC320 EMI filter/input connector, a detachable
line cord is provided

Interface Connector:

9 pin “D” connector, a mating connector is provided

Output Connector:

A detachable 10 foot (3 meter) HV cable is provided
for units up to 5kV; 10kV through 20kV: 59” (1.5 meter);
30kV: 10 foot (3 meter)

Cooling:

Convection cooled

Dimensions

7.63˝ W X 5.03˝ H X 8.91˝ D
(194mm X 128mm X 226mm)

Weight:

≤10 pounds (4.5kg)

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive.

230

HIGH VOLTAGE
POWER SUPPLY

• MODULAR BENCH TOP DESIGN

• LOW RIPPLE AND NOISE

• 3.5 DI GIT FRONT PANEL DIGITAL METERING

• REVERSIBLE OUTPUT POLARITY

USA [phone] FAX: [phone]
UK [phone] FAX: [phone]
JAPAN [phone] FAX: [phone]
CHINA [phone] FAX: [phone]

e-mail: [e-mail]
www.spellmanhv.com

128051-001 REV.D

Spellman High Voltage is an ISO 9001:2000 and ISO 14001:2004 registered company

www.spellmanhv.com/manuals/230

FRONT VIEW

BACK VIEW

SIDE VIEW

HV CONN

POS NEG

METER

OFF

POWER

ON

PCS

VFS

GROUND

HIGHVOLTAGE

ADJUST

7.63 194]

5,03 [128]

1.0 [25]

.66 [17]

8.50 [216]

8.25 [210]

PAGE 2 OF 2

MODEL SELECTION TABLE

230 Voltage Current Ripple
Series

230-01R 0 to 1kV 0 to 15mA 10mV
230-03R 0 to 3kV 0 to 5mA 30mV
230-05R 0 to 5kV 0 to 3mA 50mV
230-10R 0 to 10kV 0 to 1.5mA 500mV
230-20R 0 to 20kV 0 to 0.5mA 2 volts
230-30R 0 to 30kV 0 to 0.4mA 5 volts

INTERFACE CONNECTOR

PIN SIGNAL PARAMETERS

1 Voltage Monitor 0 to 5Vdc = 0 to 100% rated voltage, Zout = 10KΩ
2 n/c none
3 Enable TTL “0” disables HV, TTL “1” or open enables HV
4 +5Vdc Reference +5.0Vdc @ 10mA, maximum
5 Current Monitor 0 to 5Vdc = 0 to 100% rated current, Zout = 10KΩ
6 Voltage Program Input 0 to 5Vdc = 0 to 100% rated voltage, Zin = 1MΩ
7 Analog Ground Ground
8 Digital Ground Ground
9 Polarity Indicator Open collector, 30V @ 25mA, positive = ON

DIMENSIONS: in.[mm]

S P E L L M A N H I G H V O LTA G E E L E C T R O N I C S C O R P O R AT I O N

230

HIGH VOLTAGE
POWER SUPPLY

OPTIONS:
Isolated (Floating) Output-Option F

Units up to and including 5kV can be provided with differential outputs
capable of floating up to ±2kV from ground. Voltage programming and
monitoring functions normally referenced to ground. Current monitoring
and metering is eliminated. Replace “R” suffix with “F” for this option.

USA [phone] FAX: [phone]
UK [phone] FAX: [phone]
JAPAN [phone] FAX: [phone]
CHINA [phone] FAX: [phone]

e-mail: [e-mail]
www.spellmanhv.com

128051-001 REV.D

Spellman High Voltage is an ISO 9001:2000 and ISO 14001:2004 registered company

IMPORTANT SAFETY PRECAUTIONS

SAFETY

THIS POWER SUPPLY GENERATES VOLTAGES THAT ARE DANGEROUS AND MAY BE FATAL.

OBSERVE EXTREME CAUTION WHEN WORKING WITH THIS EQUIPMENT.

High voltage power supplies must always be grounded.

Do not touch connections unless the equipment is off and the

Capacitance of both the load and power supply is discharged.

Allow five minutes for discharge of internal capacitance of the power supply.

Do not ground yourself or work under wet or damp conditions.

SERVICING SAFETY

.

Maintenance may require removing the instrument cover with the power on.

Servicing should be done by qualified personnel aware of the electrical hazards.

WARNING note in the text call attention to hazards in operation of these units

that could lead to possible injury or death.

CAUTION notes in the text indicate procedures to be followed to avoid possible

damage to equipment.

Copyright © 2000, Spellman High Voltage Electronics Corporation. All Rights Reserved.

This information contained in this publication is derived in part from proprietary and patent data. This information has

been prepared for the express purpose of assisting operating and maintenance personnel in the efficient use of the

model described herein, and publication of this information does not convey any right to reproduce it or to use it for

any purpose other than in connection with installation, operation, and maintenance of the equipment described.

118004-001 REV. B

WICHTIGE SICHERHEITSHINWEISE

SICHERHEIT

DIESES HOCHSPANNUNGSNETZTEIL ERZEUGT LEBENSGEFÄHRLICHE HOCHSPANNUNG.

SEIN SIE SEHR VORSICHTIG BEI DER ARBEIT MIT DIESEM GERÄT.

Das Hochspannungsnetzteil muß immer geerdet sein.

Berühren Sie die Stecker des Netzteiles nur, wenn das Gerät ausgeschaltet ist und die elektrischen

Kapazitäten des Netzteiles und der angeschlossenen Last entladen sind.

Die internen Kapazitäten des Hochspannungsnetzteiles benötigen ca. 5 Minuten, um sich zu entladen.

Erden Sie sich nicht, und arbeiten Sie nicht in feuchter oder nasser Umgebung.

SERVICESICHERHEIT

Notwendige Reparaturen können es erforderlich machen, den Gehäusedeckel während des Betriebes zu

entfernen.

Reparaturen dürfen nur von qualifiziertem, eingewiesenem Personal ausgeführt werden.

“WARNING” im folgenden Text weist auf gefährliche Operationen hin, die zu Verletzungen oder zum Tod

führen können.

“CAUTION” im folgenden Text weist auf Prozeduren hin, die genauestens befolgt werden müssen, um

eventuelle Beschädigungen des Gerätes zu vermeiden.

118004-001 REV. B