Spellman 602C-30P, 602C-15N, 602C-15P, 602C-10N, 602C-50P Instruction Manual
...
R
Instruction Manual
600 SERIES
SPELLMAN
HIGH VOLTAGE ELECTRONICS
CORPORATION
One Commerce Park
Valhalla, New York, 10595
+1(914) 686-3600* FAX: +1(914) 686-5424*
E-mail: sales@spellmanhv.com
Website: www.spellmanhv.com
600 SERIES MANUAL 118117-001 Rev A
PAGE 1 OF 2
SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION
HIGH VOLTAGE
MODULE
Spellman’s Bertan brand of 602C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 20kV, that operate off a standard switch selectable
115/230Vac input. These fully enclosed modules are
designed for bench top or OEM applications like spectrometers, detectors, imaging and electron beam usage.
The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable signal input
allows remote control of the supply.
TYPICAL APPLICATIONS
Spectrometers
Detectors
SPECIFICATIONS
Input Voltage:
115Vac, ±10%, 50/60 Hertz @ 0.5 amp
230Vac, ±10%, 50/60 Hertz @ 0.25 amp
Input voltage is fused and switch selectable
Output Polarity:
Positive or negative, specify at time of order
Output Voltage:
See “model ratings” table
Output Current:
See “model ratings” table
Voltage Regulation:
Line - ±0.001% of rated output voltage over
specified input voltage range
Load - ±0.002% of rated output voltage
for a full load change
Ripple:
See “model ratings” table
Stability:
≤0.01% per hour, after a 1/2 hour warm up
Accuracy:
Local control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)
Temperature Coefficient:
≤50ppm/°C
Arc/Short Circuit:
All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.
Operating Temperature:
0°C to +50°C
Storage Temperature:
-40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Interface Connector:
9 pin Molex connector, mating connector and pins provided
AC Input Line Connector:
3 position terminal block
Output Connector:
10´ (3 meter) detachable HV cable is provided for units
up to 5kV; 10kV through 20kV: 59˝ (1.5 meter) cable.
Cooling:
Convection cooled.
Dimensions:
5.0˝H X 3.1˝W X 8.7˝D (128mm x 78mm x 220mm)
Weight:
≤6.75 pounds (3.1kg)
Regulatory Approvals:
Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive. UL/CUL recognized, File E137710.
602C
• 1-20KV @ 10-15 WATTS
• AC INPUT MODULAR POWER SUPPLY
• 115/230 VAC SELECTABLE
• EXCELLENT REGULATION
• VERY LOW RIPPLE
• ARC/SHORT CIRCUIT PROTECTED
www.spellmanhv.com/manuals/600
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128041-001 REV. H
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
Copyright © 2005 Spellman High Voltage Electronics Corp.
INTERFACE CONNECTOR-P2
AC INPUT TERMINAL BLOCK
MODEL RATINGS TABLE
Model Output Voltage Output Current Ripple (Vpp)
602C-10P,N 0 to 1kV 0 to 15mA 15mV
602C-15P
,N 0 to 1.5kV 0 to 10mA 15mV
602C-30P,N 0 to 3kV 0 to 5mA 30mV
602C-50P,N 0 to 5kV 0 to 2mA 50mV
602C-100P,N 0 to 10kV 0 to 1mA 200mV
602C-150P,N 0 to 15kV 0 to 0.6mA 450mV
602C-200P,N 0 to 20kV 0 to 0.5mA 800mV
PIN SIGNAL SIGNAL PARAMETERS
1 n/c None
2 n/c None
3 Signal Ground Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc
Terminal Function
1 115/230 Vac Input
2 Neutral
3 Ground
PAGE 2 OF 2
TOP VIEW
BOTTOM VIEW
FRONT VIEW
REAR VIEW
HV ADJUST
P2
115V
230V
FUSE
HV OUT
LINE
NEUT
GND
8-32 UNC-2B
.25 MAX DP
3PL
1.00 [5.0]
5.03 [127]
.62 [5.0]
.42 [10.6]
7.62 [193]
3.06 [77.7]
2.12 [53.8]
1.53 [38.8]
1.06 [26.9]
5.75 [146]
DIMENSIONS: in.[mm]
SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION
HIGH VOLTAGE
MODULE
602C
Specify “P” for positive polarity or “N” for negative polarity
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128041-001 REV. H
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
Copyright © 2005 Spellman High Voltage Electronics Corp.
PAGE 1 OF 2
S P EL L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N
HIGH VOLTAGE
MODULE
Spellman’s Bertan brand of 603C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 30kV, that operate off a standard switch selectable
115/230Vac input. These fully enclosed modules are
designed for bench top or OEM applications like spectrometers, detectors, imaging and electron beam usage.
The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable signal input
allows remote control of the supply.
TYPICAL APPLICATIONS
Spectrometers
Detectors
SPECIFICATIONS
Input Voltage:
115Vac, ±10%, 50/60 Hertz @ 1.0 amp
230Vac, ±10%, 50/60 Hertz @ 0.5 amp
Input voltage is fused and switch selectable
Output Polarity:
Positive or negative, specify at time of order
Output Voltage:
See “model ratings” table
Output Current:
See “model ratings” table
Voltage Regulation::
Line: ±0.001% of rated output voltage over
specified input voltage range
Load:±0.002% of rated output voltage
for a full load change
Ripple:
See “model ratings” table
Stability:
≤0.01% per hour, after a 1/2 hour warm up
Accuracy:
Local Control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)
Temperature Coefficient:
≤50ppm/°C
Arc/Short Circuit:
All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.
Operating Temperature:
0°Cto +50
°C
Storage Temperature:
-40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Interface Connector:
9 pin Molex connector, mating connector and pins provided
AC Input Line Connector:
3 position terminal block
Output Connector:
10´ (3 meter) detachable HV cable is provided for units
up to 5kV; 10kV through 20kV: 59˝ (1.5 meter) cable,
30kV: 78˝ (2 meter) cable
Cooling:
Convection cooled
Dimensions:
5.0˝H X 5.5˝W X 8.5˝D (127mm x 140mm x 216mm)
Weight:
≤8.0 pounds (3.64kg)
Regulatory Approvals:
Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive. UL/CUL
recognized, File E137710.
603C
• 1-30KV @ 12-30 WATTS
• AC INPUT MODULAR POWER SUPPLY
• 115/230 VAC SELECTABLE
• EXCELLENT REGULATION
• VERY LOW RIPPLE
• ARC AND SHORT CIRCUIT PROTECTED
www.spellmanhv.com/manuals/600
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128042-001 REV. H
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
For locations worldwide
PAGE 2 OF 2
DIMENSIONS: in.[mm]
MODEL RATINGS TABLE
Model Output Voltage Output Current Ripple (Vpp)
603C-10P,N 0 to 1kV 0 to 30mA 15mV
603C-15P,N 0 to 1.5kV 0 to 20mA 15mV
603C-30P,N 0 to 3kV 0 to 10mA 30mV
603C-50P,N 0 to 5kV 0 to 5mA 50mV
603C-100P,N 0 to 10kV 0 to 2mA 200mV
603C-150P,N 0 to 15kV 0 to 1.5mA 450mV
603C-200P,N 0 to 20kV 0 to 1.0mA 800mV
603C-300P,N 0 to 30kV 0 to 0.4mA 6 volts
INTERFACE CONNECTOR-P2
PIN SIGNAL SIGNAL PARAMETERS
1 n/c None
2 n/c None
3 Signal Ground Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc
TOP VIEW
BOTTOM VIEW
FRONT VIEW
REAR VIEW
HV ADJUST
P2
115V
230V
FUSE
HV
OUT
LINE
NEUT
GND
8-32 UNC-2B
.31 MAX DP
3PL
5.00 [127]
7.50 [190]
.40 [10]
.44 [11]
6.40 [162]
.78 [19.8]
1.00 [25.4]
4.00 [101]
2.34 [59.4]
5.50 [139]
AC INPUT TERMINAL BLOCK
Terminal Function
1 115/230 Vac Input
2 Neutral
3 Ground
Specify “P” for positive polarity or “N” for negative polarity
S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N
HIGH VOLTAGE
MODULE
603C
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128042-001 REV. H
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
For locations worldwide
PAGE 1 OF 2
S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N
HIGH VOLTAGE
MODULE
Spellman’s Bertan brand of 605C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 20kV, which operate off a +28Vdc input (+24Vdc
optional). These fully enclosed modules are designed for
bench top or OEM applications like spectrometers, detectors, imaging and electron beam usage.
The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable
signal input allows remote control of the supply.
TYPICAL APPLICATIONS
Spectrometers
Detectors
SPECIFICATIONS
Input Voltage:
+28Vdc, ±10%, @ 0.75 amp
+24Vdc, ±10%, @ 1 amp (24V Option)
Output Polarity:
Positive or negative, specify at time of order
Output Voltage:
See “model ratings” table
Output Current:
See “model ratings” table
Voltage Regulation:
Line: ±0.001% of rated output voltage over specified
input voltage range
Load:±0.002% of rated output voltage for a full
load change
Ripple:
See “model ratings” table
Stability:
≤0.01% per hour, after a 1/2 hour warm up
Accuracy:
Local control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)
Temperature Coefficient:
≤50ppm/°C
Arc/Short Circuit:
All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.
Operating Temperature:
0°C to +50°C
Storage Temperature:
-40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Interface Connector:
9 pin Molex connector, mating connector and pins provided
Output Connector:
59˝ (1.5 meter) detachable HV cable is provided
Cooling:
Convection cooled
Dimensions:
5.0˝H X 2.75˝W X 4.75˝D (128mm x 70mm x 121mm)
Weight:
≤3.2 pounds (1.45kg)
Regulatory Approvals:
Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive.
605C
• 1-20KV @ 6-9 WATTS
• DC INPUT MODULAR POWER SUPPLY
• EXCELLENT REGULATION
• VERY LOW RIPPLE
• ARC/SHORT CIRCUIT PROTECTED
www.spellmanhv.com/manuals/600
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128043-001 REV. F
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
For locations worldwide
TOP VIEW
BOTTOM VIEW
FRONT VIEW
REAR VIEW
HV ADJUST
HV
P2
8-32 UNC-2B
.31 MAX DP
2PL
4.78 [121]
.81 [20.5]
MAX.
3.50 [88.90]
5.03 [127]
2.75 [69.85]
1.38 [35]
.64 [35.0]
.25 [6.35]
P2
PAGE 2 OF 2
DIMENSIONS: in.[mm]
INTERFACE CONNECTOR-P2
MODEL RATINGS TABLE
Model Output Voltage Output Current Ripple (Vpp)
605C-10P,N 0 to 1kV 0 to 9mA 15mV
605C-15P,N 0 to 1.5kV 0 to 6mA 15mV
605C-30P,N 0 to 3kV 0 to 3mA 30mV
605C-50P,N 0 to 5kV 0 to 1.5mA 50mV
605C-100P,N 0 to 10kV 0 to 0.75mA 200mV
605C-150P,N 0 to 15kV 0 to 0.4mA 450mV
605C-200P,N 0 to 20kV 0 to 0.25mA 750mV
PIN SIGNAL SIGNAL PARAMETERS
1 Power Ground Power Ground
2 Power Input +28Vdc Power Input (+24Vdc optional)
3 Signal Ground Signal Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc
S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N
HIGH VOLTAGE
MODULE
605C
Specify “P” for positive polarity or “N” for negative polarity
Corporate Headquarters
Hauppauge, New York USA
+1-631-630-3000 FAX: +1-631-435-1620
e-mail: sales@spellmanhv.com
www.spellmanhv.com
128043-001 REV. F
Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company
For locations worldwide
Loading...