Spellman 602C-30P, 602C-15N, 602C-15P, 602C-10N, 602C-50P Instruction Manual

R

Instruction Manual

600 SERIES

SPELLMAN
HIGH VOLTAGE ELECTRONICS
CORPORATION

One Commerce Park
Valhalla, New York, 10595

[phone]* FAX: [phone]*
E-mail: [e-mail]
Website: www.spellmanhv.com

600 SERIES MANUAL 118117-001 Rev A

PAGE 1 OF 2

SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION

HIGH VOLTAGE
MODULE

Spellman’s Bertan brand of 602C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 20kV, that operate off a standard switch selectable
115/230Vac input. These fully enclosed modules are
designed for bench top or OEM applications like spec­trometers, detectors, imaging and electron beam usage.

The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable signal input
allows remote control of the supply.

TYPICAL APPLICATIONS

Spectrometers
Detectors

SPECIFICATIONS

Input Voltage:

115Vac, ±10%, 50/60 Hertz @ 0.5 amp
230Vac, ±10%, 50/60 Hertz @ 0.25 amp
Input voltage is fused and switch selectable

Output Polarity:

Positive or negative, specify at time of order

Output Voltage:

See “model ratings” table

Output Current:

See “model ratings” table

Voltage Regulation:

Line - ±0.001% of rated output voltage over

specified input voltage range

Load - ±0.002% of rated output voltage

for a full load change

Ripple:

See “model ratings” table

Stability:

≤0.01% per hour, after a 1/2 hour warm up

Accuracy:

Local control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)

Temperature Coefficient:

≤50ppm/°C

Arc/Short Circuit:

All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.

Operating Temperature:

0°C to +50°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Interface Connector:

9 pin Molex connector, mating connector and pins provided

AC Input Line Connector:

3 position terminal block

Output Connector:

10´ (3 meter) detachable HV cable is provided for units
up to 5kV; 10kV through 20kV: 59˝ (1.5 meter) cable.

Cooling:

Convection cooled.

Dimensions:

5.0˝H X 3.1˝W X 8.7˝D (128mm x 78mm x 220mm)

Weight:

≤6.75 pounds (3.1kg)

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive. UL/CUL recog­nized, File E137710.

602C

• 1-20KV @ 10-15 WATTS

• AC INPUT MODULAR POWER SUPPLY

• 115/230 VAC SELECTABLE

• EXCELLENT REGULATION

• VERY LOW RIPPLE

• ARC/SHORT CIRCUIT PROTECTED

www.spellmanhv.com/manuals/600

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128041-001 REV. H

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

Copyright © 2005 Spellman High Voltage Electronics Corp.

INTERFACE CONNECTOR-P2

AC INPUT TERMINAL BLOCK

MODEL RATINGS TABLE

Model Output Voltage Output Current Ripple (Vpp)

602C-10P,N 0 to 1kV 0 to 15mA 15mV
602C-15P

,N 0 to 1.5kV 0 to 10mA 15mV
602C-30P,N 0 to 3kV 0 to 5mA 30mV
602C-50P,N 0 to 5kV 0 to 2mA 50mV
602C-100P,N 0 to 10kV 0 to 1mA 200mV
602C-150P,N 0 to 15kV 0 to 0.6mA 450mV
602C-200P,N 0 to 20kV 0 to 0.5mA 800mV

PIN SIGNAL SIGNAL PARAMETERS

1 n/c None
2 n/c None
3 Signal Ground Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc

Terminal Function

1 115/230 Vac Input
2 Neutral
3 Ground

PAGE 2 OF 2

TOP VIEW

BOTTOM VIEW

FRONT VIEW

REAR VIEW

HV ADJUST

P2

115V

230V

FUSE

HV OUT

LINE

NEUT

GND

8-32 UNC-2B
.25 MAX DP
3PL

1.00 [5.0]

5.03 [127]

.62 [5.0]

.42 [10.6]

7.62 [193]

3.06 [77.7]

2.12 [53.8]

1.53 [38.8]

1.06 [26.9]

5.75 [146]

DIMENSIONS: in.[mm]

SPELLMAN HIGH VOLTAGE ELECTRONICS CORPORATION

HIGH VOLTAGE
MODULE

602C

Specify “P” for positive polarity or “N” for negative polarity

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128041-001 REV. H

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

Copyright © 2005 Spellman High Voltage Electronics Corp.

PAGE 1 OF 2

S P EL L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

Spellman’s Bertan brand of 603C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 30kV, that operate off a standard switch selectable
115/230Vac input. These fully enclosed modules are
designed for bench top or OEM applications like spec­trometers, detectors, imaging and electron beam usage.

The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable signal input
allows remote control of the supply.

TYPICAL APPLICATIONS

Spectrometers

Detectors

SPECIFICATIONS

Input Voltage:

115Vac, ±10%, 50/60 Hertz @ 1.0 amp

230Vac, ±10%, 50/60 Hertz @ 0.5 amp

Input voltage is fused and switch selectable

Output Polarity:

Positive or negative, specify at time of order

Output Voltage:

See “model ratings” table

Output Current:

See “model ratings” table

Voltage Regulation::

Line: ±0.001% of rated output voltage over

specified input voltage range

Load:±0.002% of rated output voltage

for a full load change

Ripple:

See “model ratings” table

Stability:

≤0.01% per hour, after a 1/2 hour warm up

Accuracy:

Local Control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)

Temperature Coefficient:

≤50ppm/°C

Arc/Short Circuit:

All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.

Operating Temperature:

0°Cto +50

°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Interface Connector:

9 pin Molex connector, mating connector and pins provided

AC Input Line Connector:

3 position terminal block

Output Connector:

10´ (3 meter) detachable HV cable is provided for units
up to 5kV; 10kV through 20kV: 59˝ (1.5 meter) cable,
30kV: 78˝ (2 meter) cable

Cooling:

Convection cooled

Dimensions:

5.0˝H X 5.5˝W X 8.5˝D (127mm x 140mm x 216mm)

Weight:

≤8.0 pounds (3.64kg)

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive. UL/CUL
recognized, File E137710.

603C

• 1-30KV @ 12-30 WATTS

• AC INPUT MODULAR POWER SUPPLY

• 115/230 VAC SELECTABLE

• EXCELLENT REGULATION

• VERY LOW RIPPLE

• ARC AND SHORT CIRCUIT PROTECTED

www.spellmanhv.com/manuals/600

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128042-001 REV. H

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

PAGE 2 OF 2

DIMENSIONS: in.[mm]

MODEL RATINGS TABLE

Model Output Voltage Output Current Ripple (Vpp)

603C-10P,N 0 to 1kV 0 to 30mA 15mV

603C-15P,N 0 to 1.5kV 0 to 20mA 15mV

603C-30P,N 0 to 3kV 0 to 10mA 30mV

603C-50P,N 0 to 5kV 0 to 5mA 50mV

603C-100P,N 0 to 10kV 0 to 2mA 200mV

603C-150P,N 0 to 15kV 0 to 1.5mA 450mV

603C-200P,N 0 to 20kV 0 to 1.0mA 800mV

603C-300P,N 0 to 30kV 0 to 0.4mA 6 volts

INTERFACE CONNECTOR-P2

PIN SIGNAL SIGNAL PARAMETERS

1 n/c None
2 n/c None
3 Signal Ground Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc

TOP VIEW

BOTTOM VIEW

FRONT VIEW

REAR VIEW

HV ADJUST

P2

115V

230V

FUSE

HV
OUT

LINE
NEUT
GND

8-32 UNC-2B
.31 MAX DP

3PL

5.00 [127]

7.50 [190]

.40 [10]

.44 [11]

6.40 [162]

.78 [19.8]

1.00 [25.4]

4.00 [101]

2.34 [59.4]

5.50 [139]

AC INPUT TERMINAL BLOCK

Terminal Function

1 115/230 Vac Input
2 Neutral
3 Ground

Specify “P” for positive polarity or “N” for negative polarity

S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

603C

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128042-001 REV. H

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

PAGE 1 OF 2

S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

Spellman’s Bertan brand of 605C modular high voltage
power supplies offer well regulated, fixed polarity outputs
up to 20kV, which operate off a +28Vdc input (+24Vdc
optional). These fully enclosed modules are designed for
bench top or OEM applications like spectrometers, detec­tors, imaging and electron beam usage.

The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable
signal input allows remote control of the supply.

TYPICAL APPLICATIONS

Spectrometers
Detectors

SPECIFICATIONS

Input Voltage:

+28Vdc, ±10%, @ 0.75 amp

+24Vdc, ±10%, @ 1 amp (24V Option)

Output Polarity:

Positive or negative, specify at time of order

Output Voltage:

See “model ratings” table

Output Current:

See “model ratings” table

Voltage Regulation:

Line: ±0.001% of rated output voltage over specified

input voltage range

Load:±0.002% of rated output voltage for a full

load change

Ripple:

See “model ratings” table

Stability:

≤0.01% per hour, after a 1/2 hour warm up

Accuracy:

Local control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)

Temperature Coefficient:

≤50ppm/°C

Arc/Short Circuit:

All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.

Operating Temperature:

0°C to +50°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Interface Connector:

9 pin Molex connector, mating connector and pins provided

Output Connector:

59˝ (1.5 meter) detachable HV cable is provided

Cooling:

Convection cooled

Dimensions:

5.0˝H X 2.75˝W X 4.75˝D (128mm x 70mm x 121mm)

Weight:

≤3.2 pounds (1.45kg)

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive.

605C

• 1-20KV @ 6-9 WATTS

• DC INPUT MODULAR POWER SUPPLY

• EXCELLENT REGULATION

• VERY LOW RIPPLE

• ARC/SHORT CIRCUIT PROTECTED

www.spellmanhv.com/manuals/600

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128043-001 REV. F

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

TOP VIEW

BOTTOM VIEW

FRONT VIEW

REAR VIEW

HV ADJUST

HV

P2

8-32 UNC-2B
.31 MAX DP
2PL

4.78 [121]

.81 [20.5]

MAX.

3.50 [88.90]

5.03 [127]

2.75 [69.85]

1.38 [35]

.64 [35.0]

.25 [6.35]

P2

PAGE 2 OF 2

DIMENSIONS: in.[mm]

INTERFACE CONNECTOR-P2

MODEL RATINGS TABLE

Model Output Voltage Output Current Ripple (Vpp)

605C-10P,N 0 to 1kV 0 to 9mA 15mV
605C-15P,N 0 to 1.5kV 0 to 6mA 15mV
605C-30P,N 0 to 3kV 0 to 3mA 30mV
605C-50P,N 0 to 5kV 0 to 1.5mA 50mV
605C-100P,N 0 to 10kV 0 to 0.75mA 200mV
605C-150P,N 0 to 15kV 0 to 0.4mA 450mV
605C-200P,N 0 to 20kV 0 to 0.25mA 750mV

PIN SIGNAL SIGNAL PARAMETERS

1 Power Ground Power Ground
2 Power Input +28Vdc Power Input (+24Vdc optional)
3 Signal Ground Signal Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc

S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

605C

Specify “P” for positive polarity or “N” for negative polarity

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128043-001 REV. F

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

PAGE 1 OF 2

S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

Spellman’s Bertan brand of 606C modular high voltage
power supplies offer well regulated, fix polarity outputs up
to 30kV, which operate off a +28Vdc input (+24Vdc
optional). These fully enclosed modules are designed for
bench top or OEM applications like spectrometers, detec­tors, imaging and electron beam usage.

The output voltage can be controlled by either a local
internal potentiometer or by a customer provided ground
referenced signal for remote operation. Additionally
ground referenced output voltage and current monitor
signals are provided. A high voltage enable signal input
allows remote control of the supply.

TYPICAL APPLICATIONS

Spectrometers

Detectors

SPECIFICATIONS

Input Voltage:

+28Vdc, ±10%, @ 2.25 amps
+24Vdc, ±10%, @ 2.5 amps (24V Option)

Output Polarity:

Positive or negative, specify at time of order

Output Voltage:

See “model ratings” table

Output Current:

See “model ratings” table

Voltage Regulation

Line: ±0.001% of rated output voltage over specified

input voltage range

Load:±0.002% of rated output voltage for a

full load change

Ripple:

See “model ratings” table

Stability:

≤0.01% per hour, after a 1/2 hour warm up

Accuracy:

Local control ±0.2%
Remote Programming ±(0.1% of setting + 0.1% of maximum)
Voltage Monitor ±(0.1% of reading + 0.1% of maximum)
Current Monitor ±(2% of reading + 1% of maximum)

Temperature Coefficient:

≤50ppm/°C

Arc/Short Circuit:

All units are fully arc and short circuit protected and will limit
continuous short circuit output current to less than 110% of
maximum rated output current.

Operating Temperature:

0°C to +50°C

Storage Temperature:

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Interface Connector:

9 pin Molex, mating connector and pins provided

Output Connector:

10´ (3 meter) detachable HV cable is provided for units
up to 5kV; 10kV through 20kV: 59˝ (1.5 meter) cable;
30kV: 78˝ (2 meter) cable

Cooling:

Convection cooled

Dimensions:

5.0˝H X 5.50˝W X 4.75˝D (128mm x 140mm x 121mm)

Weight:

≤3.2 pounds (1.45kg)

Regulatory Approvals:

Compliant to 2004/108/EC, the EMC Directive and
2006/95/EC, the Low Voltage Directive.

606C

• 1-30KV @ 12-30 WATTS

• DC INPUT MODULAR POWER SUPPLY

• EXCELLENT REGULATION

• VERY LOW RIPPLE

• ARC SHORT CIRCUIT PROTECTED

www.spellmanhv.com/manuals/600

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128044-001 REV. F

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

PAGE 2 OF 2

DIMENSIONS: in.[mm]

INTERFACE CONNECTOR-P2

PIN SIGNAL SIGNAL PARAMETERS

1 Power Ground Power Ground
2 Power Input +28Vdc Power Input (+24Vdc optional)
3 Signal Ground Signal Ground
4 Voltage Program 0 to 5Vdc = 0 to 100% rated output, 1MΩ Zin
5 +5.0Vdc Reference +5.0Vdc, 10mA maximum
6 kV Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
7 mA Monitor 0 to 5Vdc = 0 to 100% rated output, 10KΩ Zout
8 Trip Input Connect to ground to trip unit off
9 Local Voltage Program Internal program potentiometer wiper, 0 to 5Vdc

MODEL RATINGS TABLE

Model Output Voltage Output Current Ripple (Vpp)

606C-10P,N 0 to 1kV 0 to 30mA 15mV
606C-15P,N 0 to 1.5kV 0 to 20mA 15mV
606C-30P,N 0 to 3kV 0 to 10mA 30mV
606C-50P,N 0 to 5kV 0 to 5mA 50mV
606C-100P,N 0 to 10kV 0 to 2mA 200mV
606C-150P,N 0 to 15kV 0 to 1.5mA 450mV
606C-200P,N 0 to 20kV 0 to 1.0mA 800mV
606C-300P,N 0 to 30kV 0 to 0.4mA 6 volts

S P E L L M A N H I G H V O L T A G E E L E C T R O N I C S C O R P O R AT I O N

HIGH VOLTAGE
MODULE

606C

TOP VIEW

BOTTOM VIEW

FRONT VIEW

REAR VIEW

HV ADJUST

8-32 UNC-2B
.31 MAX DP
4PL

4.50 [114]

3.0 [76.2]

1.25 [31.75]

.56 [14]

P2

HV
OUT

5.00 [127]

5.50 [139]

1.0 [25.4]

3.0 [76]

Specify “P” for positive polarity or “N” for negative polarity

Corporate Headquarters

Hauppauge, New York USA

[phone] FAX: [phone]

e-mail: [e-mail]

www.spellmanhv.com

128044-001 REV. F

Spellman High Voltage is an ISO 9001:2008 and ISO 14001:2004 registered company

For locations worldwide

IMPORTANT SAFETY PRECAUTIONS

SAFETY

THIS POWER SUPPLY GENERATES VOLTAGES THAT ARE DANGEROUS AND MAY BE FATAL.

OBSERVE EXTREME CAUTION WHEN WORKING WITH THIS EQUIPMENT.

High voltage power supplies must always be grounded.

Do not touch connections unless the equipment is off and the

Capacitance of both the load and power supply is discharged.

Allow five minutes for discharge of internal capacitance of the power supply.

Do not ground yourself or work under wet or damp conditions.

SERVICING SAFETY

.

Maintenance may require removing the instrument cover with the power on.

Servicing should be done by qualified personnel aware of the electrical hazards.

WARNING note in the text call attention to hazards in operation of these units

that could lead to possible injury or death.

CAUTION notes in the text indicate procedures to be followed to avoid possible

damage to equipment.

Copyright © 2000, Spellman High Voltage Electronics Corporation. All Rights Reserved.

This information contained in this publication is derived in part from proprietary and patent data. This information has

been prepared for the express purpose of assisting operating and maintenance personnel in the efficient use of the
model described herein, and publication of this information does not convey any right to reproduce it or to use it for

any purpose other than in connection with installation, operation, and maintenance of the equipment described.

118004-001 REV. B

WICHTIGE SICHERHEITSHINWEISE

SICHERHEIT

DIESES HOCHSPANNUNGSNETZTEIL ERZEUGT LEBENSGEFÄHRLICHE HOCHSPANNUNG.

SEIN SIE SEHR VORSICHTIG BEI DER ARBEIT MIT DIESEM GERÄT.

Das Hochspannungsnetzteil muß immer geerdet sein.

Berühren Sie die Stecker des Netzteiles nur, wenn das Gerät ausgeschaltet ist und die elektrischen

Kapazitäten des Netzteiles und der angeschlossenen Last entladen sind.

Die internen Kapazitäten des Hochspannungsnetzteiles benötigen ca. 5 Minuten, um sich zu entladen.

Erden Sie sich nicht, und arbeiten Sie nicht in feuchter oder nasser Umgebung.

SERVICESICHERHEIT

Notwendige Reparaturen können es erforderlich machen, den Gehäusedeckel während des Betriebes zu

entfernen.

Reparaturen dürfen nur von qualifiziertem, eingewiesenem Personal ausgeführt werden.

“WARNING” im folgenden Text weist auf gefährliche Operationen hin, die zu Verletzungen oder zum Tod

führen können.

“CAUTION” im folgenden Text weist auf Prozeduren hin, die genauestens befolgt werden müssen, um

eventuelle Beschädigungen des Gerätes zu vermeiden.

118004-001 REV. B

PRECAUTIONS IMPORTANTES POUR VOTRE SECURITE

CONSIGNES DE SÉCURITÉ

CETTE ALIMENTATION GÉNÈRE DES TENSIONS QUI SONT DANGEUREUSES ET PEUVENT ÊTRE FATALES.

OYEZ EXTRÊMENT VIGILANTS LORSQUE VOUS UTILISEZ CET ÉQUIPEMENT.

S

Les alimentations haute tension doivent toujours être mises à la masse.

Ne touchez pas les connectiques sans que l’équipement soit éteint et que la capacité à la fois de la charge et de

l’alimentation soient déchargées.

Prévoyez 5 minutes pour la décharge de la capacité interne de l’alimentation.

Ne vous mettez pas à la masse, ou ne travaillez pas sous conditions mouillées ou humides.

CONSIGNES DE SÉCURITÉ EN CAS DE REPARATION

La maintenance peut nécessiter l’enlèvement du couvercle lorsque l’alimentation est encore allumée.

Les réparations doivent être effectuées par une personne qualifiée et connaissant les risques électriques.

Dans le manuel, les notes marquées « WARNING » attire l’attention sur les risques lors de la manipulation de ces

équipements, qui peuvent entrainer de possibles blessures voire la mort.

Dans le manuel, les notes marquées « CAUTION » indiquent les procédures qui doivent être suivies afin d’éviter

d’éventuels dommages sur l’équipement.

118004-001 REV. B

IMPORTANTI PRECAUZIONI DI SICUREZZA

SICUREZZA

QUESTO ALIMENTATORE GENERA TENSIONI CHE SONO PERICOLOSE E

POTREBBERO ESSERE MORTALI.

PONI ESTREMA CAUTELA QUANDO OPERI CON QUESO APPARECCHIO.

Gli alimentatori ad alta tensione devono sempre essere collegati ad un impianto di terra.

Non toccare le connessioni a meno che l’apparecchio sia stato spento e la capacità interna

del carico e dell’alimentatore stesso siano scariche.

Attendere cinque minuti per permettere la scarica della capacità interna dell’alimentatore

ad alta tensione.

Non mettere a terra il proprio corpo oppure operare in ambienti bagnati o saturi d’umidità.

SICUREZZA NELLA MANUTENZIONE.

Manutenzione potrebbe essere richiesta, rimuovendo la copertura con apparecchio

acceso.

La manutenzione deve essere svolta da personale qualificato, coscio dei rischi elettrici.

Attenzione alle AVVERTENZE contenute nel manuale, che richiamano all’attenzione ai

rischi quando si opera con tali unità e che potrebbero causare possibili ferite o morte.

Le note di CAUTELA contenute nel manuale, indicano le procedure da seguire per evitare

possibili danni all’apparecchio.

118004-001 REV. B

Table of Contents

I. INTRODUCTION

1.0 Scope of Manual…………………………………………………………. 2

1.1 Purpose of Equipment……………………………………………………... 2

1.2 Description……….………………………………………………………… 2

II. OPERATION

2.1 Installation………….……………………………………………………. 4

2.2 Input Power………….………………………………………………...…. 4

2.3 High Voltage Control………….…………………………………………. 4

2.3.1 Internal Potentiometer Control………………………..…………………..……. 4

2.3.2 External Potentiometer Control…………………………………………………. 4

2.3.3 External Voltage Control……………………………………………………….... 4

2.4 High Voltage Monitor……………………………………………………. 4

2.5 Output Current Monitor………………………………………………….. 4

2.6 Trip Unit…………………………………………………………………. 4

2.7 Input/Control/Monitor Connections……………………………………… 5

III. PROGRAMMING OPTIONS

3.1 General…………………………………………………………………… 5

3.2 Standard Mode…………………………………………………………… 6

3.3 -5 Volt Programming Mode (for 0-100% output voltage)………………. 6

3.4 -5 Volt Programming Mode (for 0-103% output voltage)………………. 6

3.5 Series 612C -5 Volt Programming Mode……………………………….. 6

IV. CIRCUIT DESCRIPTION

4.1 Functional Description…………………………………………………… 8

V. MAINTENANCE

5.1 General…………………………………………………………………… 8

5.2 Cleaning………………………………………………………………….. 8

600 SERIES MANUAL 1 118118-001 Rev A

SECTION I –
INTRODUCTION/SPECIFICATIONS

1.0 SCOPE OF MANUAL

This manual is provided to assist the user in
the installation and operation of the Bertan
Series 602C, 603C, 605C, 606C and 612C
modular high voltage power supplies.
Statements will apply to models in all of the
Series unless reference is made to specific
models. For the protection of personnel and
equipment, it is essential that this manual
be thoroughly read prior to the installation
and application of power.

1.1 PURPOSE OF EQUIPMENT

The Series 602C, 603C, 605C, 606C and
612C are families of regulated fixed output
polarity modular high voltage power
supplies. They provide exceptional
performance in applications such as CRT’s
spectrometers, detectors, medical imaging,
image intensifiers, E-Beam, I-Beam,
medical imaging and capillary
electrophoresis (HPCE) systems.

1.2 DESCRIPTION

The units are fully enclosed and designed to
easily satisfy system or bench top
operation. A wide range of stable output
voltages, up to 30kV are available. The
output voltage is controlled locally by a
minimum 15-turn potentiometer. Remote
analog voltage of resistance programming is
also available to the user as a standard
feature. All units offer a 0 to +5Vdc analog
monitor output proportional to the output
current.

The Series 602C, 603C and 612C require
an input of 115/230Vac (switch selectable)
+10%, 50-60Hz. The Series 605C and 606C
require a +28Vdc +10% input (or +24Vdc
±10% for units equipped with +24V Option).
Each unit in the Series converts the applied
power to a high voltage DC output. This
output voltage is highly regulated and
filtered. The high voltage assembly is fully
encapsulated in silicone rubber for reliable,
arc-free, stable operation.

HV Connector: SERIES 602C, 603C, 605C 606C

MODEL

HV OUTPUT

CONNECTOR

MATING HV

CONNECTOR

602C

-15 P, N thru -50 P, N
603C & 606C

-15 P, N thru -50 P, N

All 605C and all

-100 P, N and -150 P, N 8101FP

All –200P,N

All –300P,N

UG-931/U (MHV) UG-932/U (Bertan PDB)

1705-1

KINGS 1707-1 (SHV)

Bertan PAE)

8101M

(Bertan PGC-008L151-000)

8101M

8101FP

(Bertan PGC-008L1 51-000)

8111M

8111SFP

(Bertan PGQ-008L201 -000)

Only the mating connectors for the 8101 FP
and 8111 SFP (assembled to an unshielded
high voltage cable) are provided. For other HV
mating connectors order separately.

600 SERIES MANUAL 2 118118-001 Rev A

SERIES 612C

)

(kg)

MODEL HV OUTPUT MATING HV

CONNECTOR

CONNECTOR
KIT

612C-200 JJA 405787
612C-300 JJA 405787

612C-500 JJB 405786

The appropriate mating connector kit is provided
with each Series 612C unit. For pre-assembled
high voltage cables, please consult factory.

Size and Weight

WEIGHT
Lbs

SERIES

SIZE
H” x W” x D” (mm

602C 5.03 x 3.06 x 8.66 6.75

(1 25 x 78 x 220) (3.1)

603C 5.00 x 5.50 x 8.50 8.0

(127 x 140 x 216) (3.64)

605C 5.04 x 2.75 x 4.75 3.2

(128 x 70 140 x 114) (1.45)

606C 5.00 x 5.50 x 4.50 3.5

(127 x 140 x 114) (1.6)

612C 4.88 x 8.38 x 9.75 9

(124 x 213 x 248) (4.1)

600 SERIES MANUAL 3 118118-001 Rev A

SECTION II – OPERATION

internal potentiometer setting.

CAUTION: THIS UNIT CAN STORE
HAZARDOUS VOLTAGE! COMPLETELY
DISCHARGE THE HIGH VOLTAGE TO
GROUND BEFORE ATTEMPTING
REMOVAL OF THE HIGH VOLTAGE
CABLE.

2.1 INSTALLATION

All power supplies can be mounted in any
position using the tapped holes in the base
plate. The mounting screws should extend
no more than ¼” into the unit. Series 602C
and 605C require #8-32 mounting screws.
Series 603C, 606C, and 612C require #10­32 mounting screws.

2.2 INPUT POWER

Input power is applied via the 3-terminal
terminal strip for the Series 602C, 603C,
and 612C or via the 9-pin connector for the
Series 605C and 606C. The terminal or pin
connections are as listed in Section 2.7.

CAUTION: APPLICATION OF INPUT
POWER CAN IMMEDIATELY PRODUCE
A HIGH VOLTAGE OUTPUT!

2.3 HIGH VOLTAGE CONTROL

There are three modes of controlling the
high voltage. The use can select mode by
making appropriate connections via the 9­pin Molex connector. All modes provide high
voltage control from 0 to 100% (± 0.5%).

2.3.3 EXTERNAL VOLTAGE CONTROL

See Section 2.7 for hook-up information.
The output high voltage can be controlled
by a 0 to +5Vdc analog signal.

2.4 HIGH VOLTAGE MONITOR

See Section 2.7 for hook-up information. A
0 to +5Vdc analog signal, which is
proportional to the output high voltage. The
monitor has a series impedance of 10kW.

2.5 OUTPUT CURRENT MONITOR

See Section 2.7 for hook-up information. A
0 to +5Vdc analog signal, which is
proportional to the output current. The
monitor has a series impedance of 10kW.

2.6 TRIP UNIT

See Section 2.7 for hook-up information. It
provides the user with a means of remote
turn ON/OFF. This input requires a contact
closure to ground to turn off the high
voltage. A NPN open collector transistor
logic can also be employed. When no
connection is made to this input the high
voltage is enabled.

2.3.1 INTERNAL POTENTIOMETER
CONTROL

See Section 2.7 for hook-up information.
This will allow control of the high voltage
output by means of the multi-turn
potentiometer accessible via a hole in the
cover.

2.3.2 EXTERNAL POTENTIOMETER
CONTROL

See Section 2.7 for hook-up information.
Connecting an external potentiometer
(recommended value of 5kW) will control
the high voltage output independently of the

600 SERIES MANUAL 4 118118-001 Rev A

2.7 INPUT/CONTROL/MONITOR
CONNECTIONS

INPUT POWER CONNECTIONS SERIES
602C/603C/612C ONLY

TERMINAL FUNCTION

1 115/230Vac Input

2 Neutral

3 Ground

PIN LAYOUT INPUT/CONTROL/MONITOR
CONNECTOR (P2)

CONTROL AND

MONITORING CONNECTIONS

ALL MODELS

P2/PIN# FUNCTION

3 Ground

4

Program Input

5 +5Vdc Reference

6 kV Monitor

7 Current Monitor
8

Trip (Short to Gnd)

9 Internal Program

INPUT POWER CONNECTIONS SERIES

605C/606C ONLY

P2/PIN# FUNCTION

1 +Vcc Return

2 +Vcc Input

Note: To obtain local control using the
internal potentiometer accessible at the top
of the unit, jumper P2 pin 4 to pin 9.

For remote potentiometer control connect the
remote potentiometer as follows:
CW terminal to P2 pin 5
CCW terminal to P2 pin 3
Wiper terminal to P2 pin 4

For remote 0 to +5V voltage programming,
apply the input program voltage to P2 pin 4.

For remote TRIP connect P2 pin 8 to P2 pin
3

SECTION III PROGRAMMING OPTIONS

3.1 GENERAL

To provide additional flexibility and
compatibility with earlier models, provision
has been included to allow voltage
programming of all models with a 0 to –5
Volt programming input. There are four
different jumper-selectable modes for
programming. The jumpers for selecting the
required operating mode are located on
PCB100 (the large PCB), easily accessible
upon removal of the cover. Jumper
locations are shown below in Table III-1.

600 SERIES MANUAL 5 118118-001 Rev A

The four modes are described below. The

first three modes apply to all Series 602C,
603C, 605C, 606C and 612C units. The last
mode applies only to the Series 612C and is
included only with Series 612C units
ordered with the –5VPRO option.

3.2 STANDARD MODE

The unit is shipped in this configuration and
operation is as described in the previous
sections of this instruction manual. The unit
can be controlled using the internal pot or
programmed with a remote 0 to +5 Volt
signal or controlled with a remote
potentiometer.

3.3 -5 VOLT PROGRAMMING (for 0 to
100% output voltage) MODE

To achieve this operation the jumpers on
PCB100 must be configured as shown in
the chart below. In this mode the
programming signal is applied to P2 pin 4,
same as for Standard Mode, only now a 0 to
–5 Volt programming input is required to
achieve 0 to 100% output voltage
programming. No jumpers should be
attached to P2, the external connector. In
this mode there is no internal control, the
internal potentiometer is bypassed.

This mode is included to provide exact
compatibility with some previous units. It
also provides the user with a controllable
upper limit on the programmed output for an
input of –5 Volts.

3.5 SERIES 612C –5 VOLT
PROGRAMMING MODE

Series 612C units ordered with the –5VPRO
(-5 Volt Programming) option, include an
extra 5 pin hexagonal connector (J3). The
connector contains additional monitor
outputs and a 0 to – 5 Volt programming
input. This option provides compatibility with
earlier Series 612C models when used with
–5 Volt programming. The mating connector
for J3 is included and J3 connections are
shown below in Table III-2.

In this mode the programming signal is
applied to J3 pin A. A 0 to –5 Volt
programming input is required to achieve 0
to 100% output voltage programming. No
jumpers should be attached to P2, the
external connector. In this mode there is no
internal control, the internal potentiometer is
bypassed.

3.4 -5 VOLT PROGRAMMING (for 0 to
103% output voltage) MODE:

To achieve this operation the jumpers on
PCB100 must be configured as shown in
the chart below. In this mode the
programming signal is applied to P2 pin 4,
same as for Standard Mode. No jumpers
should be attached to P2, the external
connector.

In this mode the internal potentiometer is
used to control the maximum programmed
output voltage at –5 Volt programming
input. With the potentiometer fully
clockwise, the output will be 0 to 103% of
maximum for a 0 to –5 Volt input. With the
potentiometer turned up approximately half
way, a 0 to –5 Volt input will produce a 0 to
approximately 50% of maximum output
voltage.

600 SERIES MANUAL 6 118118-001 Rev A

TABLE III-1 PCB 100 JUMPER
POSITIONS

STANDARD MODE:

Jumper pins 1 to 3, pins 5 to 7

3.3 -5 VOLT PROGRAMMING (for 0 to
100% output voltage) MODE: Jumper pins 1
to 2, pins 3 to 4

3.4 -5 VOLT PROGRAMMING (for 0 to
103% output voltage) MODE: Jumper pins 1
to 2, pins 3 to 5, and pins 6 to 8

3.5 ERIES 612C –5 VOLT
PROGRAMMING MODE: Jumper pins 3 to
5, pins 4 to 6, and pins 7 to 8

TABLE III-2 J3 PIN CONNECTIONS
(Series 612C Option –5VPRO only)

PIN A: 0 to –5Volt programming input
PIN B: NC
PIN D: Output voltage monitor (0 to +5V for
0 to maximum HV output) PIN E: GND
PIN H: Output current monitor (0 to +5V for

0 to maximum current out)

600 SERIES MANUAL 7 118118-001 Rev A

SECTION IV – CIRCUIT DESCRIPTION

4.1 FUNCTIONAL DESCRIPTION

The 602C, 603C, and 612C employ a standard
step-down transformer to obtain a nominal
+28Vdc from the input ac power. The Series
605C and 606C obtain +28Vdc (+24Vdc for
+24V Option models) from the input ac power.
The circuit converts the +Vdc low voltage input

DC power to a high voltage DC output. This
output voltage is highly regulated and filtered and
can be varied either by the local potentiometer
control or through the REMOTE PROGRAM
input.

equipment used to perform the calibration. All
measurements are traceable to the National
Institute of Standards and Technology
(N.I.S.T.). Contact the factory for additional
details.

5.2 CLEANING

Cleaning of the power supply should only be
performed with the supply disconnected from
the ac power source. A soft cloth moistened
with conventional ammonia-based cleaning
agents will suffice for all exposed surfaces. The
exposed shell of the HV connector should be
cleaned with isopropyl alcohol.

An oscillator determines the frequency
(approximately 20kHz) at which all
amplification, high voltage transformation,
rectification and filtering occurs. The
amplification is a function of a control voltage
which performs the function of control and
regulation. A sample of the output voltage is
compared against a reference voltage in the
sensing circuit. The sensing circuit generates
the control voltage to set and maintain a fixed
high voltage output.

The encapsulated high voltage assembly
includes a high voltage power transformer,
rectifier or multiplier circuits, ripple filter and
sensing circuits. These are all critical, custom
designed and encapsulated components.

SECTION V – MAINTENANCE

5.1 GENERAL

The high voltage power supply should not
require any maintenance or calibration. It is
designed for reliable, trouble free operation. If
any question should arise, contact the Bertan
Customer Service Department for assistance or
return authorization. Although it is felt that
adequate information is provided in this
manual, it is suggested that the unit be
returned to the factory is service should
become necessary.

If the supply is operated in a dusty
environment, an accumulation of dust/debris
may build-up inside the unit which may cause
noisy operation (i.e., “ticking” or minor
crackling) in the area of the HV cabling on the
10kV through 30kV models. The safest way to
remove such debris is with compressed air.
Ensure that no dust/debris is left behind in the
insulative medium of the HV output connector
after this cleaning operation. Such dust may be
removed with a cotton swab moistened with
isopropyl alcohol.

The power supply can be returned to the
factory for annual calibration and certification to
its original specification. For traceability, a
certificate will be issued, identifying the serial
number of the unit calibrated and all test

600 SERIES MANUAL 8 118118-001 Rev A

SPELLMAN HIGH VOLTAGE ELECTRONICS

WARRANTY

Spellman High Voltage Electronics (“Spellman”) warrants that all power supplies it manufactures will be

free from defects in materials and factory workmanship, and agrees to repair or replace, without charge, any
power supply that under normal use, operating conditions and maintenance reveals during the warranty
period a defect in materials or factory workmanship. The warranty period is twelve (12) months from the
date of shipment of the power supply. With respect to standard SL power supplies (not customized) the
warranty period is thirty-six (36) months from the date of shipment of the power supply.

This warranty does not apply to any power supply that has been:

• Disassembled, altered, tampered, repaired or worked on by persons unauthorized by Spellman;

• subjected to misuse, negligent handling, or accident not caused by the power supply;

• installed, connected, adjusted, or used other than in accordance with the original intended appl ication and/or

instructions furnished by Spellman.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

The buyer’s sole remedy for a claimed breach of this warranty, and Spellman’s sole liability is limited, at

Spellman’s discretion, to a refund of the purchase price or the repair or replacement of the power supply at
Spellman’s cost. The buyer will be responsible for shipping charges to and from Spellman’s plant. The

buyer will not be entitled to make claim for, or recover, any anticipatory profits, or incidental, special or
consequential damages resulting from, or in any way relating to, an alleged breach of this warra nty.

No modification, amendment, supplement, addition, or other variation of this warranty will be binding unless
it is set forth in a written instrument signed by an authorized officer of Spellman.

For an authorization to ship contact Spellman’s Customer Service Department. Please state the model and
serial numbers, which are on the plate on the rear panel of the power supply and the reason for return. A
Return Material Authorization Code Number (RMA number) is needed from Spellman for all returns. The
RMA number should be marked clearly on the outside of the shipping container. Packages received without
an RMA Number may delay return of the product. The buyer shall pay shipping costs to and from Spellman.
Customer Service will provide the Standard Cost for out-of-warranty repairs. A purchase order for this
amount is requested upon issuance of the RMA Number (in-warranty returns must also be accompanied by
a “zero-value” purchase order). A more detailed estimate may be made when the power supply is received
at Spellman. In the event that the cost of the actual repair exceeds the estimate, Spellman will contact the
customer to authorize the repair.

Spellman will warrant for three (3) months or balance of product warranty, whichever is longer, the repaired
assembly/part/unit. If the same problem shall occur within this warranty period Spellman shall undertake all
the work to rectify the problem with no charge and/or cost to the buyer. Should the cause of the problem be
proven to have a source different from the one that has caused the previous problem and/or negligence of
the buyer, Spellman will be entitled to be paid for the repair.

For a complete listing of Spellman’s Global Service facilities please go to:
http://www.spellmanhv.com/customerservice/service.asp

Factory Service Procedures

Factory Service Warranty

Spellman Worldwide Service Centers

101520-007 REV D