Speedtech 64-72 User Manual

Dec 06, 2013

Chicane Coilover Kit

For '64 to '72 Chevelle/ A Body

Installation Instructions

The following instructions are intended for professional installers
and are guidelines only. Speedtech Performance assumes NO

responsibility for the installation of any of its products. All products are
intended for off road use only and must be installed by qualified
professionals only.

Thank you for purchasing your new Speedtech Chicane Coilover Conversion Kit. Installing this
product will require the removal of your front suspension. Take all necessary precautions
whenever jacking up your vehicle and use safe and sturdy jack stands to support the vehicle
whenever it is off the ground. Be sure to take all other safety precautions required to do the job
correctly.

1 | P a g e

Coilover Conversion Hardware Kit Checklist

Coilover Conversion Instructions -1

Bolts

Upper Shock Mount Shoulder Bolt (2)

½ x 1 ¾ NC

Lower T Bar Shock Mount Bolt (4)

3/8 x 1 ¼ NF

Nylock Nuts

3/8 Upper Shock Mount NC (2)

Standard Nuts

3/8 Lower Shock Mount NF (4)

Washers

3/8 Plate Upper Shock Mount (2)

3/8 Lower Shock Mount (4)

2 | P a g e

The vehicle should be on a level surface before you start.

1. Before any removal begins, disconnect the battery. But you knew that.

2. Remove upper control arms, coil springs and shocks. To give you more
working room you may want to remove the spindle as well.

3. Passenger side pictured. Front >>> Remove the existing Upper Shock
mount. Cut along the dotted line and the facotry weld (arrow).

DO NOT CUT OFF THE UPPER CONTROL ARM MOUNT!

3 | P a g e

4. After the shock mount is removed, you will need to remove the inner spring

cup and clearance the hole to about 4 ½” in diameter. This is best done with a

plasma cutter or oxyacetyline torch.

5. Test fit the Chicane upper shock bracket into place, centered over the hole.
Notice one side of the bracket has a notch in the base. This side goes towards
the front of the vehicle. Mark the width of the bracket on the control arm mount.
Using these marks as a guide, cut out a notch so that the shock bracket butts up
flush against the outer side of control arm mount.

4 | P a g e

6. This is what you should end up with. Do not proceed to welding at this time.

5 | P a g e

7. Assemble the coilover shocks as per the supplied instructions. Be sure to place the

“T” bar in the lower mount and secure it with external snap rings. Make sure the snap

rings are seated in the grooves correctly.

6 | P a g e

7 | P a g e

8. Do not skip this step. Mock up the lower control arm and coilover shock
assembly to make sure the upper Chicane mount is located in the correct
location. This also ensures that all shock components clear the frame. To allow
you to work with both hands and keep everything in place, support the lower
control arm and shock assembly. We recommend a small piece of chain or nylon
rope. Align them so that the lower control arm is level to the ground and set the
shock approximately in the middle of its travel. This will be close to the finished
ride height. You must be sure the shock is not mounted in a way that binds the
bushings and/or bearings.

9. Assemble the Chicane Bracket to the shock top eyelet. Align barcket into
position so that the shock is centered in the hole and will travel without hitting the
frame. Some slight trimming of the bracket notch you previously made may be
necessary. When you are sure everything is aligned properly, TACK weld the
upper Chicane mount in this location.

8 | P a g e

10. On some frames, depending on shock and spring combination, it may be
necessary to clearance the inner section of the control arm mount as seen in the
photo below. Do not do this with the shock installed.

11. Remove the shock assembly and then remove the spring from the shock.
Reinstall the shock into the lower control arm and the Chicane bracket to test
again for any binding throughout the control arm's range of motion. Now that you
have double checked everything and there is no bind and no clearance issues,
you can final weld the Chicane upper bracket in place.

12. Once all welding is completed you can paint and/or reassemble all
suspension components.

9 | P a g e

Torque Specs

 Lower control arm nuts 40 ft/lbs
 Upper control arm nuts 40 ft/lbs
 Upper shock mount 30 ft/lbs
 Lower T bar mounting nuts 40 ft/lbs.

Be sure to double check all the fasteners! Set the car to the approximate
ride height by adjusting the shock lower spring nuts. This should be done
before aligning the car.

Note: Do not drive the car until an alignment has been performed by a
COMPETANT alignment or race car shop.

Speedtech Performance USA LLC

3884 S River Rd, Bldg A

St George, UT 84770

435-628-4300

speedtechperformance.com

10 | P a g e

Terms and Conditions of Sale

1. Effective January, 2008, supersedes all previous policy statements. Policies are subject to change without notice. Speed tech performance
Ltd. is not responsible for printing errors.

2. Speed Tech Performance Ltd. does not endorse, nor recommend modification of vehicles for use on public highways, since warranty or
government regulations may be violated. As an express condition of sale of any performance part, the buyer acknowledges and agrees to use
the performance parts for the modification of vehicles in sanctioned OFF-ROAD competitive events and show purposes only. Customers
should exercise their discretion on matters with regards to the purchase and installation of these products.

3. Speed Tech Performance Ltd. does not ensure the legal use of these products. We do not guarantee the fitment of these products for
anything other than there intended application nor do we assume any responsibilities what so ever for the misuse or losses incurred by the
use of any of these components. While every effort is made to provide technical information and assistance, we have no control over owner
installation, modification, and unusual stress that performance parts are subject to.

4. The customer acknowledges that Speed Tech Performance Ltd. and its employees are not responsible for any mechanical failures due to
the use of parts sold, supplied or installed not for their intended application. Speed Tech Performance Ltd will not be held liable for any
damages which are incurred directly or indirectly on the vehicles or operators or passengers of the vehicle

5. Please consult your sales agent and/or technician prior to purchase of any of Speed Tech Performance Ltd. Products to ensure proper fit.
The buyer assumes all responsibilities for determining the suitability of the product. All aftermarket products should always be installed by
professionals only.

Warranty Claim:

1. Speed tech Performance Ltd. Warrants its products against materials and workmanship failure for the term of 12 months (1 year) from the
date of purchase and only up to the amount paid with proof of purchase.

2. Seller’s liability shall as limited to repairing or replacing, at its option, any defective product which is returned, freight prepaid to Seller,
according to the Merchandise Return Procedure set forth in Section 3 below. Buyer shall bear all responsibility for shipping charges and risk of
loss or damage during transit to Seller. Products which have been subjected to abuse, misuse, alteration, neglect or unauthorized repair or
installation, as determined solely by Seller, are not covered by this warranty. Any alterations, addition, improvements or attachments to the
product(s) not authorized in writing by the Seller shall be deemed to be a waiver of this warranty by Buyer and shall render this warranty null
and void. Seller shall return repaired or replaced product(s) to Buyer, at its expense via regular ground service in Canada. Shipping charges
by all other methods and to all other destinations shall be borne by Buyer.

3. Merchandise return procedure
A. If you purchased your Speed tech performance ltd product from us or from an authorized dealer, you are covered by the terms of this policy.
All claims however, must be submitted directly to Speed tech performance Ltd.
B. Call the customer service representative at 1-888-467-1625.
C. Provide the invoice number, date of purchase and reason for return
D. You will be assigned a Returned Goods Authorization Number (RGA). The package you return must show the RGA on the outside of the
package, include the original invoice and be shipped prepaid to our facility. The part has to be in its original packaging materials and be in a
resellable condition. For parts presenting signs of use, only warranty claims will be accepted.
E. Ship to seller, freight pre-paid and insured for replacement cost in original packaging.
F. Replacement or repair decision will be made when merchandise is received by seller. No advance replacement is available.

How to File a Warranty Claim:

The answer to ALL the following questions should be YES before contacting our Customer Service Department.
Is the part appropriate to your application?
Did you carefully and thoroughly read the instructions provided along with the part?
Do you have the proof of purchase?
Are you the original purchaser?
Is the part unmodified and clean?
Is the return date within 3 months from the purchase date?
Is the reason for return a legitimate product defect?
If the answer to all these questions is YES, please contact our Customer Service Department at 1-888-467-1625. You will be given a Returned
Goods Authorization Number (RGA) valid for 30 days. You will also be asked to ship the part prepaid to our facility. All shipments MUST be
prepaid, include the original invoice and show the RGA on the outside of the package, otherwise it will be refused. Please include a brief
explanation letter in order to expedite the warranty analysis process.

What doesn’t this Warranty Cover?

The costs not covered by this warranty include but are not limited to:

- Removal, installation, shipment and insurance costs.

- Improper installation or maintenance

- Misuse or abuse, negligence

- Damage to related components

- Normal wear and tear.

- Costs incurred due to down time of vehicle

- Alterations on the original design or unauthorized repairs.
All warranties implied by law are limited in duration of this warranty. You have specific rights that may vary from state to state or Province to

Province. By purchasing any of the products that are manufactured by speed tech performance you agree to any and all of the above terms
and conditions. Copyright © Speedtech Performance USA LLC

11 | P a g e

This page intentionally left blank

12 | P a g e