Speed Queen SC80VNV Installation Manual

Washer-Extractors

Cabinet Hardmount

Refer to Page 6 for Model Identification

Installation

Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com.

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

CHM166C

Part No. F232135R11

January 2008

Table of

Contents

Safety Information.............................................................................. 2

Explanation of Safety Messages........................................................... 2

Important Safety Instructions ............................................................... 2

Safety Decals ........................................................................................ 4

Operator Safety..................................................................................... 5

Introduction......................................................................................... 6

Model Identification ............................................................................. 6

Delivery Inspection............................................................................... 9

Nameplate Location.............................................................................. 9

Replacement Parts ................................................................................ 11

Customer Service.................................................................................. 11

Remove After Shipment (OPL Models Only)...................................... 11

Specifications and Dimensions........................................................... 12

Dimensional Clearances ....................................................................... 23

Installation........................................................................................... 24

Machine Foundation ............................................................................. 24

Concrete Foundation Installation..................................................... 26

Machine Anchoring .............................................................................. 29

Direct-to-Finished-Floor Installation ............................................... 29

Mounting Bolt Hole Locations (Without Elevated Base Frames)........ 32

Mounting Bolt Hole Locations (Without Elevated Base Frames)........ 38

Elevated Base Frame Installation..................................................... 48

Gap Setting for Vibration Switch

(Variable-Speed and Fixed-Speed Models) ................................... 50

Drain Connection.................................................................................. 56

Drain Connection.................................................................................. 57

Water Connection Requirements.......................................................... 59

Electrical Installation Requirements..................................................... 60

Input Voltage Requirements ............................................................ 60

Circuit Breakers ............................................................................... 60

Connection Specifications ............................................................... 61

Grounding ........................................................................................ 61

Phase Adder ..................................................................................... 61

Thermal Overload Protector ............................................................ 61

Troubleshooting ............................................................................... 69

Steam Requirements (Steam Heat Option Only).................................. 69

Supply Dispensing (OPL Machines Only) ........................................... 70

Connection of External Liquid Supplies.......................................... 70

Door Handle Adjustment...................................................................... 75

Control Function Test........................................................................... 76

means without the expressed written consent of the publisher.

F232135

1

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

WARNING

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer.

3. Do not wash textiles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

CAUTION

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

5. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

6. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7. Before the washer is removed from service or discarded, remove the door to the washing compartment.

8. Do not reach into the washer if the wash drum is moving.

2

F232135

Safety Information

9. Do not install or store the washer where it will be exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out.

12. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

13. Use washer only for its intended purpose, washing textiles.

14. Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket.

15. ALWAYS disconnect the washer from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

16. Install the washer according to the INSTALLATION INSTRUCTIONS. All connections for water, drain, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

17. To reduce the risk of fire, textiles which have traces of any flammable substances such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals such as in mops and cleaning cloths, must not be put into the washer. These flammable substances may cause the fabric to catch on fire by itself.

18. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

19. Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the service agent.

21. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

22. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open.

23. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet).

24. Always follow the fabric care instructions supplied by the textile manufacturer.

25. Never operate the washer with any guards and/or panels removed.

26. DO NOT operate the washer with missing or broken parts.

27. DO NOT bypass any safety devices.

28. Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

F232135

3

Safety Information

WARNING

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

WARNING

Install the machine on a level floor of sufficient strength. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W703

CAUTION

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

WARNING

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

To provide personal safety and keep the machine in proper working order, follow all maintenance and safety procedures presented in this manual. If questions regarding safety arise, contact the manufacturer immediately.

Use manufacturer-authorized spare parts to avoid safety hazards.

4

F232135

Safety Information

Operator Safety

WARNING

NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury.

SW012

To ensure the safety of machine operators, the following maintenance checks must be performed daily:

1. Prior to operating the machine, verify that all warning signs are present and legible. Missing or illegible signs must be replaced immediately. Make certain that spares are available.

2. Check door interlock before starting operation of the machine:

a. Attempt to start the machine with the door

open. The machine should not start with the door open.

b. Close the door without locking it and attempt

to start the machine. The machine should not start with the door unlocked.

Do not bypass any safety devices in the machine.

WARNING

Never operate the machine with a bypassed or disconnected balance system. Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage.

SW039

c. Close and lock the door and start a cycle.

Attempt to open the door while the cycle is in progress. The door should not open.

If the door lock and interlock are not functioning properly, call a service technician.

3. Do not attempt to operate the machine if any of the following conditions are present:

a. The door does not remain securely locked

during the entire cycle.

b. Excessively high water level is evident.

c. Machine is not connected to a properly

grounded circuit.

F232135

5

Introduction

Model Identification

Information in this manual is applicable to these models:

18

20

25

27

HC18EC2 HC18MC2 HC18MD2 HC18MDX HC18MH2 HC18MN2 HC18MX2 HC18NC2 HC18NP2 HC18NR2 HC18NX2

DC20NC2 HC20AC2

HC20ACV HC20AL2 HC20AX2 HC20AY2 HC20AYV HC20BC2 HC20BL2 HC20BN2 HC20BX2 HC20BY2

DC25NC2 HC25AC2

HC25AL2 HC25AX2 HC25AY2 HC25BC2 HC25BL2 HC25BX2 HC25BY2 HC25EC2 HC25MC2 HC25MD2 HC25MDX HC25MH2

HC27EC2 HC27MC2 HC27MD2 HC27MDX HC27MH2 HC27MN2 HC27MX2 HC27MV2 HC27NC2

HC18PC2 HC18SN2 HC18VC2 HC18VX2

HC20MD2 HC20ML2 HC20MN2 HC20MX2 HC20MY2 HC20NC2 HC20SN2 HC20VC2 HC20VX2

HC25ML2 HC25MN2 HC25MV2 HC25MX2 HC25MY2 HC25NC2 HC25NP2 HC25NR2 HC25NX2 HC25PC2 HC25SN2 HC25VC2 HC25VX2

HC27NP2 HC27NR2 HC27NX2 HC27SN2 HC27VC2 HC27VX2

NC18MD2 NC18MDX NC18MX2 NC18NC2 NC18ND2 NC18NP2 NC18NR2 NC18NX2 NC18VC2 NC18VX2

NC25MD2 NC25MDX NC25MX2 NC25NC2 NC25NP2 NC25NR2 NC25NX2 NC25VC2 NC25VX2

NC27MD2 NC27MDX NC27MX2 NC27NC2 NC27NP2 NC27NR2 NC27NX2 NC27VC2 NC27VX2

(continued)

SC18EC2 SC18EP2 SC18MC2 SC18MC3 SC18MD2 SC18MD3 SC18MH2 SC18MH3 SC18MN2 SC18MN3 SC18MV2

SC20AC2 SC20ACV SC20AL2 SC20AN2 SC20AX2 SC20AY2 SC20AYV SC20BC2 SC20BL2 SC20BN2 SC20BX2

SC25AC2 SC25AL2 SC25AX2 SC25AY2 SC25BC2 SC25BL2 SC25BX2 SC25BY2 SC25EC2 SC25EP2 SC25MC2 SC25MD2 SC25MH2

SC27EC2 SC27EP2 SC27MC2 SC27MD2 SC27MH2 SC27MN2 SC27MV2 SC27MX2 SC27NC2

SC18MV3 SC18MX2 SC18NC2 SC18NP2 SC18NR2 SC18NX2 SC18PC3 SC18SN2 SC18SN3 SC18VN2 SC18VNV

SC20BY2 SC20MD2 SC20ML2 SC20MN2 SC20MX2 SC20MY2 SC20NC2 SC20NR2 SC20NX2 SC20VN2

SC25ML2 SC25MN2 SC25MV2 SC25MX2 SC25MY2 SC25NC2 SC25NP2 SC25NR2 SC25NX2 SC25SN2

SC27NP2 SC27NR2 SC27NX2 SC27SN2 SC27VN2 SC27VNV

UC18MC2 UC18MC3 UC18MD2 UC18MD3 UC18MH2 UC18MH3 UC18MN2 UC18MN3 UC18MV2 UC18MV3

UC20AN2 UC20BN2 UC20MD2 UC20ML2 UC20MN2 UC20MX2 UC20PN2 UC20VN2

UC25MC2 UC25MD2 UC25MH2 UC25MN2 UC25MV2 UC25MX2 UC25PC2 UC25PN2

UC27MC2 UC27MD2 UC27MN2 UC27MX2 UC27PN2 UC27VN2 UC27VNV

UC18MX2 UC18PC2 UC18PC3 UC18PN2 UC18PN3 UC18VN2 UC18VNV

6

F232135

30

35

40

50

DC30AC2 DC30NC2

DC40AC2 DC40NC2

HC30AC2 HC30ACV HC30AL2 HC30AX2 HC30AY2 HC30AYV HC30BC2 HC30BL2 HC30BN2 HC30BX2 HC30BY2

HC35EC2 HC35MC2 HC35MD2 HC35MDX HC35MH2 HC35MN2 HC35MV2 HC35MX2 HC35NC2 HC35NP2 HC35NR2

HC40AC2 HC40ACV HC40AL2 HC40AX2 HC40AY2 HC40AYV HC40BC2 HC40BL2 HC40BN2 HC40BX2 HC40BY2 HC40MD2

HC50BC2 HC50BL2 HC50BN2 HC50BX2 HC50BY2 HC50EC2 HC50MC2 HC50MD2 HC50MH2 HC50ML2 HC50MN2 HC50MV2 HC50MX2 HC50MY2 HC50NC2

HC30MD2 HC30ML2 HC30MN2 HC30MX2 HC30MY2 HC30NC2 HC30SN2 HC30VC2 HC30VX2

HC35NX2 HC35PC2 HC35SN2 HC35VC2 HC35VNV HC35VX2

HC40ML2 HC40MN2 HC40MX2 HC40MY2 HC40NC2 HC40NR2 HC40NX2 HC40SN2 HC40VC2 HC40VX2

HC50NP2 HC50NR2 HC50NX2 HC50PC2 HC50SN2 HC50VC2 HC50VNV HC50VX2

(continued)

NC35MD2 NC35MDX NC35MX2 NC35NC2 NC35NP2 NC35NR2 NC35NX2 NC35VC2 NC35VX2

NC40NC2 NC40NR2 NC40NX2

NC50MD2 NC50MDX NC50MX2 NC50NC2 NC50NP2 NC50NR2 NC50NX2

(continued)

SC30AC2 SC30ACV SC30AL2 SC30AN2 SC30AX2 SC30AY2 SC30AYV SC30BC2 SC30BL2 SC30BN2 SC30BX2

SC35EC2 SC35EP2 SC35MC2 SC35MC3 SC35MD2 SC35MD3 SC35MH2 SC35MH3 SC35MN2 SC35MN3 SC35MV2

SC40AC2 SC40ACV SC40AL2 SC40ANV SC40AN2 SC40AX2 SC40AY2 SC40AYV SC40BC2 SC40BL2 SC40BN2 SC40BX2

SC50BC2 SC50BL2 SC50BN2 SC50BX2 SC50BY2 SC50EC2 SC50EP2 SC50MC2 SC50MC3 SC50MD2 SC50MD3 SC50MH2 SC50MH3 SC50ML2 SC50MN2

SC30BY2 SC30MD2 SC30ML2 SC30MN2 SC30MX2 SC30MY2 SC30NC2 SC30NR2 SC30NX2 SC30VN2

SC35MV3 SC35MX2 SC35NC2 SC35NP2 SC35NR2 SC35NX2 SC35PC3 SC35SN2 SC35SN3 SC35VN2 SC35VNV

SC40BY2 SC40MD2 SC40ML2 SC40MN2 SC40MX2 SC40MY2 SC40NC2 SC40NR2 SC40NX2 SC40VN2 SC40VNV

SC50MN3 SC50MV2 SC50MV3 SC50MX2 SC50MY2 SC50NC2 SC50NP2 SC50NR2 SC50NX2 SC50PC3 SC50SN2 SC50SN3 SC50VN2 SC50VNV

UC30AN2 UC30BN2 UC30ML2 UC30MN2 UC30MX2 UC30PN2 UC30VN2

UC35MC2 UC35MC3 UC35MD2 UC35MD3 UC35MH2 UC35MH3 UC35MN2 UC35MN3 UC35MV2 UC35MV3 UC35MX2

UC40ANV UC40AN2 UC40BN2 UC40MN2 UC40PN2 UC40VN2 UC40VNV

UC50BN2 UC50MC2 UC50MC3 UC50MD2 UC50MD3 UC50MH2 UC50MH3 UC50MN2 UC50MN3 UC50MV2 UC50MV3 UC50MX2 UC50PC2 UC50PC3 UC50PN2

Introduction

UC35PC2 UC35PC3 UC35PN2 UC35VN2 UC35VNV

UC50PN3 UC50VN2 UC50VNV

F232135

7

Introduction

(continued)

60

80

125

DC60AC2 DC60NC2

HC60AC2 HC60ACF HC60ACV HC60AL2 HC60ALF HC60AX2 HC60AXF HC60AY2 HC60AYF HC60AYV HC60BC2 HC60BCF HC60BL2 HC60BLF HC60BN2 HC60BNF HC60BX2 HC60BXF HC60BY2 HC60BYF

DC80NCV HC80ACV

HC80ALV HC80ANV HC80AXV HC80AYV HC80BCV HC80BLV HC80BNV HC80BXV HC80BYV HC80MC3 HC80MD2

HC125BCV HC125BYV

HC60MD2 HC60ML2 HC60MN2 HC60MX2 HC60MY2 HC60NC2 HC60NCF HC60NR2 HC60NX2 HC60SN2 HC60VC2 HC60VN2 HC60VNF HC60VX2

HC80MD3 HC80MH3 HC80MN3 HC80MV3 HC80NCV HC80NRV HC80NXV HC80PC3 HC80SN3 HC80VCV HC80VNV HC80VXV

NC80NCV NC80NPV NC80NRV NC80NXV NC80VCV NC80VXV

SC60AC2 SC60ACF SC60ACV SC60AL2 SC60ALF SC60AN2 SC60ANF SC60ANV SC60AX2 SC60AXF SC60AY2 SC60AYF SC60AYV SC60BC2 SC60BCF SC60BL2 SC60BLF SC60BN2 SC60BNF SC60BX2

SC80ACV SC80ALV SC80ANV SC80AXV SC80AYV SC80BCV SC80BLV SC80BNV SC80BXV SC80BYV SC80ECV SC80EPV

SC125ANV SC125BCV

SC60BXF SC60BY2 SC60BYF SC60MD2 SC60ML2 SC60MN2 SC60MX2 SC60MY2 SC60NC2 SC60NCF SC60NR2 SC60NRF SC60NYF SC60NX2 SC60NXF SC60PN2 SC60SN2 SC60VN2 SC60VNF SC60VNV

SC80MC3 SC80MD3 SC80MH3 SC80MN3 SC80MV3 SC80NCV SC80NPV SC80NRV SC80NXV SC80NYV SC80SN3 SC80VNV

SC125BYV SC125VNV

UC60AN2 UC60ANF UC60ANV UC60BC2 UC60BCF UC60BL2 UC60BN2 UC60BNF UC60BY2 UC60BYF UC60BX2 UC60BXF UC60MN2 UC60PN2 UC60SN2 UC60VN2 UC60VNF UC60VNV

UC80ANV UC80BNV UC80MC3 UC80MD3 UC80MH3 UC80MN3 UC80MV3 UC80PC2 UC80PC3 UC80PN3 UC80VNV

UC125ANV UC125VNV

8

F232135

Introduction

This manual is designed as a guide to the installation of the Cabinet Hardmount Washer-Extractor.

NOTE: All information, illustrations, and specifications contained in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

Delivery Inspection

Upon delivery, visually inspect crate, protective cover, and unit for any visible shipping damage. If the crate, protective cover, or unit is damaged or signs of possible damage are evident, have the carrier note the condition on the shipping papers before the shipping receipt is signed, or advise the carrier of the condition as soon as it is discovered.

Remove the crate and protective cover as soon after delivery as possible. If any damage is discovered upon removal of the crate and/or protective cover, advise the carrier and file a written claim immediately.

Nameplate Location

The nameplate is located at the rear of the machine and inside door. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1.

1

1 Nameplate

CHM167R

Figure 1

F232135

9

Introduction

Model Number Familiarization Guide

Sample Model Number: *C40AC2OU60001 *C 40

A C

2

O

U6

0001

* Denotes Brand

Model Number Prefix

Washer-Extractor Capacity (pounds dry weight of laundry)

Type of Electrical Control

Actuation (C = Coin drop)

Washer-Extractor Speed Capability (2 = 2 speed)

Electrical Characteristics

Design Series

Option Identification (varies from machine to machine)

*C40AC2OU60001

00000000000

208 – 240

7

60 3

40

N/A N/A

Drawing:

15

3

18.2

EXAMPLE OF NAMEPLATE

Figure 2

470

0

CHM2079N

10

F232135

Introduction

Replacement Parts

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor.

Customer Service

For technical assistance, call (920) 748-3121, Ripon, Wisconsin U.S.A.

Remove After Shipment (OPL Models Only)

A yellow retainer has been inserted in the door locks of all cabinet hardmount on-premise laundry washerextractors to prevent the door from locking during shipment. Remove the yellow retainer during installation by pulling it off.

NOTE: Once retainer is removed, machine must be powered to unlock door.

A tag has been attached to the washer-extractor’s door handle as a reminder that the retainer must be removed before operation. Refer to Figure 3.

F232135

Remove Yellow Retainer Before Starting Machine.

Note: A Retainer has been inserted to prevent the door from locking during shipment.

Figure 3

CFS503N

11

Specifications and Dimensions

2 Speed Models

Specification 18, 20 25 27, 30 35 40 50 60

Weight and Shipping Information

Net weight, lbs. (kg) 353

(160)

Domestic shipping weight, lbs. (kg)

Domestic shipping volume,

3

ft

(m3)

Export shipping weight lbs. (kg)

Export shipping volume, ft

3

(m

)

Wash Cylinder Information

Cylinder diameter, in. (mm)

Cylinder depth, in. (mm) 13.75

Cylinder volume, ft

Perforation size, in. (mm)

3

(l) 2.76

373

(169)

27

(.76)

461

(209)

3

36.7

(1.04)

21

(533)

(349)

(78.1)

0.188

(4.76)

427

(193)

448

(203)

31.3

(.89)

536

(243)

47.7

(1.3)

21

(533)

18.75 (476)

3.76

(106.5)

0.188

(4.76)

496

(225)

519

(235)

34.4

(.98)

600

(272)

49.5

(1.40)

24

(610)

16

(406)

4.19

(118.6)

0.188

(4.76)

650

(295)

680

(309)

39

(1.09)

760

(345)

47.1

(1.32)

26.25 (667)

18.38 (467)

5.76

(163.1)

0.188

(4.76)

686

(311)

710

(322)

43.6

(1.24)

810

(367)

65.6

(1.86)

26.25 (667)

20.25 (514)

6.34

(180)

0.188

(4.76)

820

(372)

875

(398)

49.8

(1.41)

1020

(464)

68.6

(1.94)

30

(762)

20

(508)

8.18

(232)

0.188

(4.76)

811

(368)

838

(380)

52.2

(1.48)

947

(430)

74.7

(2.12)

30

(762)

22

(559)

9.00

(255)

0.188

(4.76)

Perforation open area, % 17 17 18 17 17.5 18 18

12

F232135

Specifications and Dimensions

2 Speed Models (Continued)

Specification 18, 20 25 27, 30 35 40 50 60

Door Opening Information

Door opening diameter, in. (mm)

Height of door bottom above floor, in. (mm)

Height of door opening above floor, in. (mm)

11.63 (295)

14.38 (365)

17.19 (437)

Power Consumption

Average power used per cycle, kW-hr

No load

Sheets

Tow el s

.06 .116 .13 .30 .196 .42 .25

.10 .116 .14 N/A .195 N/A .26

.11 .127 .16 N/A .213 N/A .33

Average BTu/hr, (Kcal./hr) 425

(107)

Drive Train Information

Number of motors in drive train

Wash/reverse power, HP (kW)

0.15

(0.11)

High extract power, HP (kW) 0.74

(0.55)

11.63 (295)

14.38 (365)

17.19 (437)

400

(101)

14.34 (364)

14

(356)

17

(431)

463

(117)

13.94 (354)

16

(406)

19

(483)

510

(129)

16.24 (413)

14.5

(368)

19

(483)

510

(129)

16.25 (413)

18.25 (464)

18.5

(470)

700

(176)

16.25 (413)

15

(381)

18.5

(470)

700

(176)

1111111

0.25

(0.19)

1.4

(1.04)

0.24

(0.18)

1.34

(1.00)

0.40

(0.30)

1.8

(1.3)

0.40

(0.30)

1.8

(1.3)

0.55

(0.41)

2.7

(2.01)

0.55

(0.41)

2.7

(2.01)

Cylinder Speeds

Wash/reverse speed, RPM57574947514444

High extract speed, RPM 528 529 464 470 491 450 469

Centrifugal Force Data

Wash/reverse centrifugal

0.93 0.97 0.82 0.82 0.97 0.83 0.83

force, Gs

High extract centrifugal

83.1 83.5 73.3 82.3 89.8 86.3 93.8

force, Gs

F232135

13

Specifications and Dimensions

2 Speed Models (Continued)

Specification 18, 20 25 27, 30 35 40 50 60

Balance Detection

Vibration switch installed N/A N/A N/A N/A N/A N/A N/A

Direct Steam Heating (Optional)

Steam inlet connection size, in. (mm)

.50

(13)

.50

(13)

.50

(13)

.50

(13)

.50

(13)

.50

(13)

.50

(13)

Number of steam inlets 1111111

Steam required to raise bath water temperature 10°F (10°C), lbs. (kg)

Average steam use per cycle, bhp (kg)

LOW

MED

HIGH

.74

(.335)

1.07

(0.487)

1.44

(0.653)

0.338

(5.32)

.94

(0.43)

1.28

(0.58)

1.74

(0.79)

0.41

(6.45)

1.11

(0.50)

1.49

(0.68)

1.83

(0.83)

0.44 (6.9)

1.42

(0.643)

N/A

2.58

(1.167)

0.61

(9.55)

1.85

(0.84)

2.54

(1.15)

3.28

(1.48)

0.78

(12.2)

1.71

(0.776)

2.53

(1.147)

3.41

(1.545)

0.80

(12.51)

1.98

(0.895)

3.01

(1.384)

4.23

(1.916)

0.98

(15.4)

Electrical Heating (Optional)

Total electrical heating capacity, kW

Input Voltage

200V

240V

380V

415V

480V

5.4 5.4 5.4 10.8 10.8 16.3 16.3

7.8 7.8 7.8 15.6 15.6 23.4 23.4

6.5* 6.5 6.5* 13.0 13.0 19.6 19.6

7.8* 7.8 7.8* 15.5 15.5 23.3 23.3

10.4* 10.4 10.4* 20.8 20.8 31.2 31.2

Electrical heating elements 3336399

Electrical heat element size, kW 2.6 2.6 2.6 2.6 5.2 2.6 2.6

* Applicable to fixed-speed inverter drive models.

14

F232135

Specification 18 35 50 80

Overall Dimensions

Specifications and Dimensions

3-Speed Models

Overall width, in. (mm) 26

(660)

Overall height, in. (mm) 42

(1067)

Overall depth, in. (mm) 29.69

(754)

Weight and Shipping Information

Net weight, lb. (kg) 400

(182)

Domestic shipping weight, lb. (kg) 430

(195)

Domestic shipping volume, ft

3

(m3) 23.9

(0.669)

Export shipping weight, lb. (kg) 490

(223)

Export shipping volume, ft

3

(m3) 47.1

(1.32)

Wash Cylinder Information

Cylinder diameter, in. (mm) 21

(533)

30.13 (765)

47.25

(1200)

38.5

(978)

675

(307)

780

(355)

39.0

(1.09)

785

(357)

47.1

(1.32)

26.25 (667)

34.06 (865)

49.75

(1265)

42

(1067)

950

(432)

990

(450)

49.8

(1.39)

1150

(523)

68.6

(1.92)

30

(762)

41.5

(1054)

56

(1422)

51.63

(1311)

1600

(727)

1650

(743)

78.1

(2.19)

1700

(765)

N/A

36

(914)

Cylinder depth, in. (mm) 13.75

(349)

Cylinder volume, ft

3

(l) 2.76

(78.1)

Perforation size, in. (mm) 0.188

(4.76)

18.38 (467)

5.76

(163.1)

0.188

(4.76)

20

(508)

8.18

(232)

0.188 (4.76)

22

(559)

12.4

(354)

0.188

(4.76)

Perforation open area,% 17 17 18 N/A

Door Opening Information

Door opening size, in. (mm) 12

(305)

Ht. door bottom above floor, in. (mm) 17.25

(438)

13.94 (354)

19

(480)

16.25 (413)

18.25 (465)

18.5

(470)

21.5

(546)

Power Consumption

Avg. power used per cycle, kW/hr 0.18 est 0.28 est 0.38 est 0.55 est.

Nominal sound emission, dBA 61 65 67 60 / 69

Background noise level, dBA 48 49 49 47

Average HVAC load, Btu/hr. 440 525 725 900

F232135

15

Specifications and Dimensions

3-Speed Models (Continued)

Specification 18 35 50 80

Drive Train Information

Number of motors in drive train 1 2 2 2

Wash/reverse power, hp (kW) 0.18

(0.13)

Medium extract power, hp (kW) 1.2

(0.895)

High extract power, hp (kW) 1.5

(1.12)

0.40

(0.30)

0.45

(0.34)

3.0

(2.2)

0.90

(0.67)

1.0

(0.75)

3.5

(2.6)

1.0

(0.75)

1.2

(0.89)

4.5

(3.36)

Cylinder Speeds

Wash/reverse speed, RPM 46 47 44 40

Medium extract speed, RPM 330 75 60 64

High extract speed, RPM 661 591 561 530

Centrifugal Force Data

Wash/reverse centrifugal force, Gs 0.65 0.82 0.825 0.82

Medium extract centrifugal force, Gs 32.5 2.10 1.53 2.1

High extract centrifugal force, Gs 130 130 134 143

Balance Detection

Vibration safety switch installed N/A Standard Standard Standard

Direct Steam Heating (Optional)

Steam inlet connection size, in. (mm) .5

(13)

.5

(13)

.5

(13)

.5

(13)

Number of steam inlets 1 1 1 1

Steam req. to raise bath temperature 10°F, lbs . (10°C, kg)

Average steam use per cycle, bhp (kg) 0.66

LOW 1.1

(0.5)

HIGH 1.2

(0.54)

(10.35 kg)

2.1

(0.95)

2.8

(1.3)

1.4

(21.95 kg)

2.16

(.982)

2.77

(1.26)

1.4

(21.95 kg)

2.64 (1.2)

3.67

(1.67)

1.5

(23.52 kg)

Electrical Heating (Optional)

Total electrical heating capacity, kW 7.8 15.6 23.4 28.8

Electrical heating elements 3 6 9 12

Electrical heat element size, kW 2.6 2.6 2.6 2.6

16

F232135

Specification 18, 20 27, 30 35 40 50 60 80 125

Weight and Shipping Information

Specifications and Dimensions

Variable-Speed and Fixed-Speed Models

Net weight, lbs. (kg) 386

(175)

Domestic shipping weight, lbs. (kg) 424

(191)

Domestic shipping volume, ft

3

(m3)27

(0.76)

Export shipping weight, lbs. (kg) 476

(215)

Export shipping volume, ft

3

(m3) 36.7

(1.04)

498

(226)

545

(245)

34.4

(.98)

588

(267)

49.5

(1.40)

621

(282)

670

(301)

39

(1.09)

731

(332)

47.1

(1.33)

706

(321)

744

(338)

43.6

(1.24)

846

(385)

65.6

(1.86)

767

(348)

818

(371)

49.8

(1.41)

967

(439)

68.6

(1.94)

773

(350)

824

(373)

52.2

(1.48)

1020

(463)

74.7

(2.12)

1346

(610)

1420

(644)

98.6

(2.79)

1545

(701)

110.3

(3.12)

2301

(1044)

2384

(1081)

163

(4.3)

2493

(1131)

173

(4.8)

Wash Cylinder Information

Cylinder diameter, in. (mm) 21

(533)24(610)

Cylinder depth, in. (mm) 13.75

(349)16(406)

Cylinder volume, ft

3

(l) 2.76

(78.1)

Perforation size, in. (mm) 0.188

(4.76)

4.19

(118)

0.188

(4.76)

26.25 (667)

18.38 (467)

5.76

(163)

0.188

(4.76)

26.25 (667)30(762)30(762)36(914)42(1067)

20.25 (514)20(508)22(559)22(559)24(610)

6.34

(180)

0.188

(4.76)

8.18

(232)

0.188 (4.76)

9.00

(255)

0.188

(4.76)

12.4

(354)

0.188

(4.76)

19.2

(544)

0.188 (4.76)

Perforation open area, % 17 18 17 17.5 18 18 18 24

Door Opening Information

Door opening size, in. (mm) 11.63

(295)

Height of door bottom above floor, in. (mm)

14.38 (365)

Height of door opening bottom, in. (mm) 17.19

(437)

14.34 (364)

14

(356)16(406)

14.34 (364)

16.25 (413)

14.5

(368)15(381)

17

(431)19(483)18(457)

16.25 (413)

18.5

(470)

16.25 (413)

18.25 (445)

N/A

18.5

(470)20(508)

17.75 (451)29(737)

21.63 (549)

30.25 (768)

Average Power Consumption

HVAC load, Btu/hr. 400 450 510 510 750 750 950 1200

F232135

17

Specifications and Dimensions

Variable-Speed and Fixed-Speed Models (Continued)

Specification 18, 20 27, 30 35 40 50 60 80 125

Drive Train Information

Number of motors in drive train 11111111

Drive motor power, hp (kW) 1

(.75)

1

(.75)

2

(1.5)

2

(1.7)

2

(1.5)

3

(2.2)

5

(3.7)

7.5

(5.6)

Cylinder Speeds

Gentle wash/reverse speed, RPM 29 27 26 26 24 26 22 26

Wash/reverse speed, RPM 52 52 46 46 43 43 40 37

Distribution speed, RPM 9292738268777065

Low extract speed, RPM 366 366 328 328 307 307 280 260

Medium extract speed, RPM

534 534 478 478 447 447 408 378 (Not available on Electronic Control models.)

High extract speed, RPM 686 686 613 613 573 574 524 485

Centrifugal Force Data

Gentle wash centrifugal force, Gs 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.43

Wash/reverse centrifugal force, Gs 0.8 0.8 0.8 0.8 0.8 0.8 0.87 0.8

Distribution centrifugal force, Gs 2.52.522.522.52.52.5

Low extract centrifugal force, Gs 40 40 40 40 40 40 40 40

Medium extract centrifugal force, Gs 85 85 85 85 85 85 85 85

High extract centrifugal force, Gs 140 140 142 140 142 140 140 140

Balance Detection

Vibration switch installed* Standard Standard Standard Standard Standard Standard Standard Standard

Direct Steam Heating (Optional)

Steam inlet connection size, in. (mm)

.5

(13)

.5

(13)

.5

(13)

.5

(13)

.5

(13)

.5

(13)

.5

(13)

.75

(19)

Number of steam inlets 1 1 1 1 1 1 1 1

Steam required to raise bath water temperature 10°F (10°C),

LOW

lbs. (kg)

MED

HIGH

Average steam use per cycle, bhp (kg)** .34

.74

(.331)

1.07

(0.48)

1.43

(0.651)

(5.33)

1.11

(0.50)

1.49

(0.68)

1.83

(0.83)

0.44

(6.86)

1.42

(0.64)

N/A

2.58

(1.16)

1.4

(21.9)

1.85

(0.84)

2.54

(1.15)

3.28

(1.48)

0.78

(12.2)

1.71

(0.77)

2.53

(1.15)

3.4

(1.54)

0.8

(12.3)

2.0

(0.91)

3.1

(1.41)

4.2

(1.91)

0.98

(15.4)

2.58

(1.17)

4.65

(2.11)

5.79

(2.63)

1.34

(20.9)

3.64

(1.6)

5.17

(2.3)

7.78

(3.5)

2.01

(31.45)

* Refer to Gap Setting for Vibration Switch (Variable-Speed Models) section for specifications.

** All motels, except 35 and 50, are based on normal 95°C international cycle in BN2 control.

18

F232135

Variable-Speed and Fixed-Speed Models (Continued)

Specification 18, 20 27, 30 35 40 50 60 80 125

Electrical Heating (Optional)

Specifications and Dimensions

Total electrical heating capacity, kW

Input Vo l t a g e

200V 5.4 5.4 10.8 10.8 16.3 16.3 21.7 N/A

240V 7.8 7.8 15.6 15.6 23.4 23.4 31.2 N/A

380V 6.5* 6.5* 13.0 13.0 19.5 19.6 19.6 N/A

415V 7.8* 7.8* 15.5 15.5 23.3 23.3 23.3 N/A

480V 10.4* 10.4* 20.8 20.8 31.2 31.2 31.2 N/A

Electrical heating elements 3 3 6 3 9 9 12 N/A

Electrical heat element size, kW 2.6 2.6 2.6 5.2 2.6 2.6 2.6 N/A

* Refer to Gap Setting for Vibration Switch (Variable-Speed Models) section for specifications.

F232135

19

Specifications and Dimensions

N

NOTE: The dimensions shown are for planning purposes only. They are approximate and subject to normal manufacturing tolerances. If exact dimensions are required for construction purposes, contact the distributor or manufacturer. We reserve the right to make changes at any time without notice.

1

T

4

3

2

J

K

S

5

9

8

6

I

A

B

C

D

E

18, 20, 25, 27, 30, 35, 40, 50, 60 AND 80 POUND CAPACITY MACHINES

1 Supply Dispenser 5 Hot Water Inlet 2 Input Power Block 6 Vacuum Breaker 3 External Chemical Supply Signal Terminal Strip

(OPL only)

4 Cold Water Inlet 9 Extra Inlet Valve

F

G

H

7 Drain Outlet 8 External Chemical Supply Inlet (OPL)

M

O

Figure 4

L

N

P

7

R

Q

CHM2086

CHM2086N

20

F232135

Machine Capacity Dimensions

Specifications and Dimensions

Dimensions

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

18, 20 25 27, 30 35 40 50 60 80

40.75 in.

(1035 mm)

23 in.

(584 mm)

17.19 in.

(437 mm)

14.38 in.

(365 mm)

26 in.

(660 mm)

25.63 in.

(650 mm)

29.81 in.

(756 mm)

0 in.

(0 mm)

42 in.

(1067 mm)

12.5 in.

(318 mm)

11.5 in.

(292 mm)

3.5 in.

(89 mm)

34.5 in.

(876 mm)

5.75 in.

(146 mm)

4.5 in.

(114 mm)

2 in.

(51 mm)

35.5 in.

(902 mm)

38.5 in.

(978 m)

1.19 in.

(30 mm)

.88 in.

(22 mm)

42.75 in.

(1086 mm)

23 in.

(584 mm)

17.19 in.

(437 mm)

14.38 in.

(365 mm)

26 in.

(660 mm)

29.63 in.

(752 mm)

38.81 in.

(858 mm)

0 in.

(0 mm)

44 in.

(1118 mm)

12.5 in.

(318 mm)

11.5 in.

(292 mm)

3.5 in.

(89 mm)

36.5 in.

(927 mm)

5.75 in.

(146 mm)

4.5 in.

(114 mm)

2 in.

(51 mm)

37.5 in.

(953 mm)

40.5 in.

(1029 mm)

1.19 in.

(30 mm)

.88 in.

(22 mm)

43.75 in.

(1111 mm)

24 in.

(610 mm)

17 in.

(432 mm)

14 in.

(356 mm)

29 in.

(737 mm)

30.63 in.

(775 mm)

33.63 in.

(854 mm)

0 in.

(0 mm)

45 in.

(1143 mm)

15.25 in.

(387 mm)

14.75 in.

(375 mm)

3.75 in.

(95 mm)

37.69 in.

(957 mm)

5.88 in.

(149 mm)

4 in.

(102 mm)

2 in.

(51 mm)

38 in.

(965 mm)

41 in.

(1041 mm)

1.19 in.

(30 mm)

.88 in.

(22 mm)

45.75 in.

(1162 mm)

26 in.

(660 mm)

19 in.

(483 mm)

16 in.

(406 mm)

30.13 in.

(765 mm)

34 in.

(864 mm)

37 in.

(941 mm)

1.13 in.

(29 mm)

47 in.

(1194 mm)

14.25 in.

(362 mm)

10.81 in.

(275 mm)

2.75 in.

(70 mm)

40.13 in.

(1019 mm)

7.31 in.

(186 mm)

4.75 in.

(121 mm)

2 in.

(51 mm)

41.94 in.

(1064 mm)

41.94 in.

(1064 mm)

1.19.

(30 mm)

.25 in.

(6 mm)

45.75 in.

(1162 mm)

26 in.

(660 mm)

18 in.

(457 mm)

14.5 in.

(368 mm)

30.63 in.

(778 mm)

36 in.

(914 mm)

39 in.

(990 mm)

0.5 in.

(13 mm)

47 in.

(1194 mm)

15.44 in.

(392 mm)

14.44 in.

(367 mm)

3.81 in.

(97 mm)

39 in.

(991 mm)

5.5 in.

(140 mm)

4.75 in.

(121 mm)

3 in.

(76 mm)

42.13 in.

(1070 mm)

43.19 in.

(1097 mm)

1.19 in.

(30 mm)

.88 in.

(22 mm)

48.75 in.

(1238 mm)

26.25 in.

(667 mm)

18.5 in

(470 mm)

15 in.

(381 mm)

34.06 in.

(865 mm)

37.75 in.

(959 mm)

41.81 in.

(1062 mm)

0.5 in.

(13 mm)

49.94 in.

(1268 mm)

20.75 in.

(527 mm)

19.75 in.

(502 mm)

3.5 in.

(89 mm)

41.5 in.

(1054 mm)

6.44 in.

(163 mm)

5 in.

(127 mm)

3 in.

(76 mm)

40.25 in.

(1022 mm)

43.25 in.

(1099 mm)

1.19 in.

(30 mm)

.88 in.

(22 mm)

48.75 in.

(1238 mm)

26.25 in.

(667 mm)

18.5 in.

(464 mm)

15 in.

(381 mm)

34.06 in.

(865 mm)

38.75 in.

(984 mm)

41.75 in.

(1060 mm)

0.5 in.

(13 mm)

49.94 in.

(1268 mm)

20.75 in.

(527 mm)

19.75 in.

(501 mm)

3.5 in.

(89 mm)

41.5 in.

(1054 mm)

6.44 in.

(163 mm)

5 in.

(127 mm)

3 in.

(76 mm)

42.5 in.

(1080 mm)

45.5 in.

(1156) mm)

1.19 in.

(30 mm)

.88 in.

(22 mm)

(1391 mm)

(781 mm)

(549 mm)

(451 mm)

(1054 mm)

(1207 mm)

(1283 mm)

(1422 mm)

(572 mm)

(381 mm)

(1219 mm)

(162 mm)

(146 mm)

(1280 mm)

(1356 mm)

54.75 in.

30.75 in.

21.63 in.

17.75 in.

41.5 in.

47.5 in.

50.5 in.

0.5 in.

(13 mm)

56 in.

22.25 in.

15 in.

3.44 in.

(87 mm)

48 in.

6.38 in.

5.75 in.

3 in.

(76 mm)

50.38 in.

53.38 in.

1.5 in.

(38 mm)

.88 in.

(22 mm)

F232135

21

Specifications and Dimensions

1

2

J

K

L

M

N

O

I

3

4

5

6

R

S

A

B

C

D

1 Dry Chemical Dispenser

(Optional – OPL Models Only)

2 Cold Water Inlet 6 Steam Inlet (Optional) 3 Extra Water Inlet (Optional) 7 Drain Outlet

E

125 POUND CAPACITY MACHINES

F

G

4 Hot Water Inlet 5 Liquid Chemical Inlet

P

H

Machine Capacity Dimensions for 125 Pound Models A B C D

40 in. (1016 mm)

30.25 in. (768 mm)

29 in. (737 mm)

8 in. (203 mm)

K

L M N

Q

7

B023I

41 in. (1041 mm)

38.5 in. (978 mm)

33.5 in. (851 mm)

29.75 in. (756 mm)

T

B023I

22

E

F G H

I

J

48 in. (1219 mm)

50.5 in. (1283 mm)

56.75 in. (1441 mm)

1 in. (25 mm)

70.5 in. (1791 mm)

44.5 in. (1130 mm)

O P Q R S

T

24 in. (610 mm)

13 in. (330 mm)

4.75 in. (124 mm)

63.88 in. (1622 mm)

64.88 in. (1648 mm)

66.63 in. (1692 mm)

F232135