Speed Queen H370I User Manual

Frontload Washers

NOTA: El manual en español aparece después del manual en inglés.

Installation

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

H370I

Part No. 801516

April 2003

Table of

Contents

Replacement Parts.............................................................................. 3

Installation........................................................................................... 5

Dimensions and Specifications............................................................. 5

Before You Start................................................................................... 6

Tools ................................................................................................ 6

Electrical .......................................................................................... 6

Water................................................................................................ 6

Accessories Bag............................................................................... 6

Installing the Washer............................................................................ 7

Step 1: Position Washer Near Installation Area .............................. 7

Step 2: Connect Water Inlet Hoses.................................................. 7

Step 3: Connect Drain Hose to Drain Receptacle............................ 8

Step 4: Position and Level the Washer ............................................ 10

Step 5: Remove the Shock Sleeves and Shipping Brace ................. 11

Step 6: Wipe Out Inside of Washer Drum....................................... 11

Step 7: Plug In the Washer............................................................... 11

Step 8: Check Installation................................................................ 12

Moving Unit to a New Location...................................................... 12

Electrical Requirements........................................................................ 12

Grounding Instructions .................................................................... 13

Water Supply Requirements................................................................. 14

Water Temperature .......................................................................... 14

Water Pressure ................................................................................. 14

Risers................................................................................................ 14

Information for Handy Reference......................................................... 15

Installer Checklist................................................................ Back Cover

means without the expressed written consent of the publisher.

801516

1

Notes

2

801516

Replacement Parts

If replacement parts are required, contact the source from which you purchased your washer, or contact:

Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, WI 54971-0990 U.S.A. Phone: (920) 748-3950

for the name and address of the nearest authorized parts distributor.

801516

3

Notes

4

801516

Installation

Dimensions and Specifications

17.5 in.

(44.8 cm)

14.9 in.

(37.9 cm)

43 in. (109.2 cm)

36.6 in. (93 cm)

31.1 in. (79 cm)

29.6 in. (75.1 cm)

28 in.

(71.1 cm)

2 in. (5.1 cm)

26.9 in.

(68.3 cm)

FLW1957N

FLW1989N

801516

5

Installation

1

2

3

4

5

Before You Start

Tools

For most installations, the basic tools you will need are:

D820I

1 Wrench 2 Screwdriver 3 Pliers 4 Socket Wrench 5 Level

Figure 1

Water

Washer needs two standard 3/4 in. (19.1 mm) water supply faucets with a pressure between 20 and 120 pounds per square inch (138 to 827 kPa). For more detailed information refer to section on Wa ter Supply Requirements.

Accessories Bag

An accessories bag has been shipped inside your washer. It includes:

● Two inlet hoses with washers. Refer to step 2 of

Installation.

● Four rubber feet. Refer to step 4 of Installation.

● Beaded tie-down strap. Refer to step 3 of

Installation.

● Installation instructions.

● Use and Care Guide.

● Operating insert.

● Warranty bond.

● Helpful Hints insert.

● Bag for storing shipping materials.

Electrical

Refer to serial plate for specific electrical requirements. For more detailed information refer to section on Electrical Requirements.

6

801516

Installation

Installing the Washer

NOTE: If the washer is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until the washer has had a chance to warm up.

Step 1: Position Washer Near Installation Area

IMPORTANT: Install dryer before washer. This allows room for attaching exhaust duct.

Move washer as close to the desired area of installation as possible.

NOTE: When installing in newly constructed or renovated building, it is very important to flush the lines since build-up may have occurred during construction.

IMPORTANT: Thread hose couplings onto valve connections finger-tight, then approximately 1/4 turn with pliers. DO NOT cross thread or overtighten couplings.

Turn water on and check for leaks. If leaks are found, retighten the hose couplings. Continue tightening and rechecking until no leaks are found.

1

2

H091I

1 Rubber Washer (Plain) 2 Inlet Hose

H091I

D772I

Figure 2

Step 2: Connect Water Inlet Hoses

NOTE: Refer to section on Water Supply Requirements before connecting water inlet hoses.

Remove the four plain rubber washers from accessories bag, and install them according to Figure 3.

Figure 3

1

4

1 Water Supply Faucets 2 Cold Water Connection 3 Hot Water Connection 4 Water Inlet Hoses

2

Figure 4

3

WATER MIXING

VALVE

FLW1990N

Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve.

801516

7

Installation

1

Step 3: Connect Drain Hose to Drain Receptacle

Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp and by removing shipping tape.

Find the instructions, on the following pages, that are appropriate for your type of drain receptacle (standpipe, sink, wall, or laundry tub). Follow these instructions to properly install the drain hose.

IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch (3.2 cm) outside diameter drain hose.

1

2

1 24 in. to 36 in. (91.44 cm recommended

height)

2 Standpipe – 2 in. (5.08 cm) or 1-1/2 in.

(4 cm)

3 Beaded Tie-Down Strap

3

Figure 6

FLW1992N

Sink Installation

For this type of installation, use the beaded tie-down strap (supplied in accessories bag) or use a large wire tie (available from your local hardware store), and secure the drain hose to the cabinet top hinge (refer to Figure 7). This will prevent the drain hose from dislodging during use.

1

FLW1991N

1 Retainer Clamp

Figure 5

Standpipe Installation

Place the drain hose into the standpipe. Remove the beaded tie-down strap from accessories

bag and place around standpipe and drain hose and tighten strap to hold hose to standpipe. This will prevent the drain hose from dislodging from drain receptacle during use.

2

FLW1993N

1 Drain Hose 2 Tie-Down Strap (Wire tie or tape if

necessary)

Figure 7

8

801516

Installation

2

3

1

In-the-Wall Installation

For installations of this type, the drain hose MUST be secured to one of the inlet hoses using the beaded tiedown strap from accessories bag.

NOTE: End of drain hose must not be below 24 in. (61 cm).

H023I

1 Drain Hose 2 Tie-Down Strap (Tape if necessary) 3 Inlet Hoses

Laundry Tub Installation

For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use. Use the beaded tie-down strap (supplied in accessories bag) to secure hose.

1

2

FLW1994N

1 Drain Hose 2 Tie-Down Strap (Tape if necessary)

Figure 9

Figure 8

801516

9

Installation

Washers elevated above floor level must be anchored to that elevated surface, base or platform. The material used to elevate the washer should also be anchored to the floor to ensure that the washer will not walk or that the washer can not be physically pulled, tipped or slid from its installed position. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W306

WARNING

Step 4: Position and Level the Washer

Place washer in position on a clean, firm and reasonably level floor. Installing the washer on any type of carpeting is not recommended.

Loosen 7/8 in. locknut and adjust the front and rear leveling legs until the washer is level from side to side and front to back (using a level). Washer should not rock.

NOTE: Level must rest on raised portion of top panel. Refer to Figure 10.

Tighten the locknuts securely against the washer base using the 7/8 in. wrench. If the locknuts are not

tight, washer will move out of position during operation.

NOTE: DO NOT slide washer across floor if the leveling legs have been extended, as legs and base could become damaged.

NOTE: Use of the dispenser drawer or washer door as a handle in the transportation of the washer may cause damage to the dispenser or door.

Remove rubber feet from accessories bag and place on all four leveling legs.

3

2

1

4

5

H381I

1 Leveling Leg 2 Washer Base 3 Level 4 Locknut 5 Rubber Foot

10

Figure 10

801516

Speed Queen H370I User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual