Speed Queen ADGE9BGS113TW01 User Manual
Important Instructions
Subject: Installing Elevated Base Pedestal on Frontload Washers and Dryers
Use With: PDR108W, PDR108B, PDR108U, PDR108G, PDR108D, PDC106B,
PDC108B, PDC110B, PDC112B Elevated Base Pedestals
WARNING
This kit is to be installed in accordance with the
manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. In
Canada, this conversion/installation shall be carried
out in accordance with the requirements of the provincial authorities having jurisdiction and in accordance with the requirements of the CAN/CGA-B149.1
and CAN/CGA-B149.2 installation code. Failure to
follow instructions could result in serious injury,
death or property damage. The qualified agency performing this work assumes all responsibility for this
kit installation.
W013R4
WARNING
To reduce the risk of electric shock, fire, explosion,
serious injury or death:
• Disconnect electric power to the machine before
servicing.
• Close gas shut-off valve to the machine before
servicing.
• Close steam gate valve to the machine before
servicing.
• Never start the machine with any guards/panels
removed.
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to
ensure that the machine is properly grounded.
Pedestal consists of:
1 Elevated Base Pedestal
4 Leveling Leg Nuts
4 Leveling Legs
4 Rubber Feet
4 5/16 in. Cap Screw (2 in.)
4 5/16 in. Lock Washer
4 5/16 in. Nut
3 Hex Screw
1 Dryer Mounting Strap
2 5/16 in. Cap Screw (3.5 in.)
8 3/8 in. Flat Washer
2 1/2 in. Screw
1 Important Instructions
Tools required for this kit:
Installation Instructions for washer or dryer
Level
Crescent Wrench
5/16 in. Socket Driver
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
W017
IMPORTANT: Elevated Base Pedestal is designed for
use with frontload washers or dryers only. Do not install on stack washer/dryer or stack dryer/dryer products. This pedestal is not designed for use with other
products.
1 Form No. 7-04-47ENR14
February 2017
NOTE: Refer to the Installation Instructions that came
FLW33K_SVG
1
2
FLW127K_SVG
2
1
with the washer or dryer when uninstalling and reinstalling the washer or dryer.
WARNING
To reduce the risk of personal injury, two people are
required to lift the unit onto the pedestal.
W526
Homestyle Washer Installation
(PDR108W, PDR108B, PDR108U,
PDR108G, PDR108D Pedestal)
1. Disconnect electrical power to unit.
2. Turn off water supply and disconnect fill hoses.
3. Disconnect drain hose from drain receptacle.
4. Install the shipping brace before tipping washer to remove
leveling legs.
5. Remove existing leveling legs from bottom of unit. When taking off legs, tip unit back to get access to legs. This will require assistance.
IMPORTANT: DO NOT tip the washer onto its side.
Only tip toward front or back.
1. Leveling Leg
2. Nut
Figure 1
c. Screw leveling legs with nuts into bottom flange of the
elevated base pedestal.
7. Place pedestal into desired final location. Position pedestal so
the notch is in the top right corner. Refer to Figure 2 .
NOTE: Save leveling legs for future use.
6. Install leveling legs included with pedestal onto bottom of
pedestal.
a. Place rubber feet on all four leveling legs.
b. Thread each nut down to within one inch of the bottom of
each leveling leg. Leave room for a wrench to fit for adjusting leg and tightening nut. Refer to Figure 1 .
1. Notch in Top Right Corner
2. Front of Pedestal
Figure 2
8. Level pedestal from front to back and from side to side by
screwing leveling legs into or out of pedestal. Refer to Figure
3 . Turn leg clockwise to lift or counterclockwise to lower.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
2 Form No. 7-04-47ENR14
FLW34K_SVG
1
3
2
1. Pedestal
FLW17K_SVG
1
2
4
3
FLW18K_SVG
1
2
2. Tighten This Nut Against Bottom of Pedestal
3. Adjust Leveling Leg
Figure 3
1. Screw
2. Washer
3. Mounting Hole
4. Nut (Dryer only - acts as a spacer)
9. Once pedestal is level, tighten the nuts installed in step 8 up
against bottom of pedestal. Refer to Figure 3 . Make sure to
hold leg when tightening nut.
10. Move pedestal into an open work area. You will need access
to back and front of unit to attach unit to pedestal.
WARNING
To reduce the risk of personal injury, two people
are required to lift the unit onto the pedestal.
W526
11. With proper help, tilt unit forward and lift. Carefully set unit
onto pedestal. Make sure front of unit is positioned to line up
with pedestal’s mounting holes. Refer to Figure 4 . Make sure
pedestal is square with front and back of unit.
Figure 4
12. Gather contents of the parts bag.
13. Remove front access panel at the lower front of unit by removing two screws from bottom edge of panel. Refer to Fig-
ure 5 .
1. Front Access Panel
2. Screw
Figure 5
14. Attach washer to pedestal by placing two cap screws and
washers from inside of washer into threaded holes on front of
pedestal. Refer to Figure 4 .
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Form No. 7-04-47ENR14
Loading...