Speed Queen ADEE8B Installation Guide

Installation Instructions

for Dryers

Original Instructions Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com

Part No. 514685R1

November 2014

Front Matter

WARNING

Risk of fire. Highly flammable material.

W881

IMPORTANT: The electrical installation in the site shall comply with the Australian Electrical Standards, AS3000, SAA wiring rules, and such local regulations that might apply. In Australia and New Zealand, installation must comply with the Gas Installations Standard AS/NZS 5601 Part 1: General Installations.

The maximum drying load (dry weight) shall not exceed 8.2 kg [18 pounds].

Read all instructions before using unit.

WARNING

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Clear the room, building or area of all occu-

pants.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed by a qualified installer, service agency or the gas supplier.

W052

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

W033

IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the dryer user smells gas. The gas utility instructions plus the SAFETY and WARNING note directly above must be posted in a prominent location near the dryer for customer use.

WARNING

• Installation of unit must be performed by a qualified installer.

• Install clothes dryer according to manufacturer’s instructions and local codes.

• DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Refer to section on connecting exhaust system. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

Part No. 514685R1

W729R1

Front Matter

WARNING

To reduce the risk of severe injury or death, follow all installation instructions. Save these instructions.

W894

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W053

This product uses FreeRTOS V7.2.0 (www.freertos.org).

NOTE: For Australian models, the energy consumption is measured as used once per week using the Perm Press Automatic cycle with High Temperature and Dryness Dry.

Dimensions............................................................................................. 6

Installation............................................................................................. 8

Before You Start.............................................................................................8

Supplies..................................................................................................... 8

Order of Installation Steps............................................................................8

Position and Level the Dryer............................................................................8

Connect Dryer Exhaust System...................................................................... 11

Exhaust Direction......................................................................................12

Exhaust System.........................................................................................13

Gas Dryers - Connect Gas Supply Pipe........................................................... 13

Reverse Door, if Desired............................................................................... 15

Wipe Out Inside of Dryer.............................................................................. 16

Plug In the Dryer.......................................................................................... 16

Electrical Requirements............................................................................. 16

Earth/Ground Instructions.......................................................................... 18

Recheck Steps.............................................................................................. 18

Check Heat Source........................................................................................18

Electric Dryers.......................................................................................... 18

Gas Dryers................................................................................................18

All Dryers.................................................................................................19

Installer Checklist.................................................................................20

Copyright 2014, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

Part No. 514685R1

Dimensions

DRY2638N_SVG

DRY2639N_SVG

M L

Electric Models

A * 1027 mm [40.42 in.]

B * 1006 mm [39.61 in.]

C * 392 mm [15.44 in.]

D * 102 mm [4 in.]

Dimensions

E 391 mm [15.4 in.]

F 683 mm [26.875 in.]

G * 114 mm [4.5 in.]

H 10 mm [0.4 in.]

I 203 mm [8 in.]

J 711 mm [28 in.]

K 597 mm [23.5 in.]

NOTE: Exhaust openings are 102 mm [4 inch] metal

* With leveling legs turned into base.

ducting.

Gas Models

1. 3/8 in. NPT Gas Connection

Part No. 514685R1

+ 14 hidden pages

Speed Queen ADEE8B Installation Guide

Table of Contents

Dimensions