Speedheat RugBuddy Operating Instructions Manual
Models:
USC.1410.11.120 ∙ USC.940.11.120 ∙ USC.470.11.120 ∙ USC.370.11.120 ∙ USC.165w.11.120 ∙ USC.165L.11.120 ∙ USC.065.11.120
Plug-in, Portable Heater for under Your Area Rug!
Opera ting Instruct ions and Safety Advice
Optional KlimaGrip™ Pad Instructions Included
IMPORTANT: Please Read Carefully before Operating
Y
Y
Speedheat® is Floor
www.speedheat.us
OOUU
MMUUSST
Heating
T
UUSSEE AA
RRUUG
G
PPAAD
D
UUNNDDEERR YYOOUURR
R
G
R
UUG
B
B
UUDDDDY
Y
™™!!
USC.470.11.120
from the box.
Write down model number and serial number of the
_ Serial
Unfold the panel completely, stretching it so that there are
Testing RugBuddy™ and Outlet Electrical Operation
prong outlet
on GFCI plug
the GFCI plug?
Yes, continue to Step 5.
button
on the GFCI plug
Yes, continue to Step 5.
another appliance such as a lamp in to outlet to test if outlet is operating correctly.
Does the lamp work in the same outlet?
Technical Support
No, your outlet is not working properly. Check your breakers, call an electrician, or plug in
portable floor heater into another working outlet.
Testing and
RugBuddy™ Panel Operation
lugging in with
Place your hand on the unfolded panel, and you should feel heat coming from the element wire.
Do you feel heat generating from the
Yes, continue installation of your
RugBuddy™
RugBuddy™
noticeable temperature difference on your back
es, continue operating as usual and enjoy!
disconnect the heating panel
Technical Support
.
∙ USC.065.11.120
on packing slip or invoice for future
_ Serial
NO CREASES
927
a properly functioning outlet.
panel under your area rug as
ay down on area rug for at least 5 minutes while in operation.
while not operating
927
RugBuddy
Portable Heater for under your Area Rug!
Models: USC.1410.11.120 ∙ USC.940.11.120 ∙
™
∙ USC.370.11.120 ∙ USC.165w.11.120 ∙ USC.165L.11.120
Operating Instructions
and Safety Advice
1. Remove the RugBuddy™
2.
reference. Model #_______________
3. *IMPORTANT*
TESTING AND TROUBLESHOOTING
1.
Plug unfolded heater in to a 3-
Press TOP “Reset” button
Is there a RED LIGHT on
o
o No, press bottom
Is there a RED LIGHT
o
o No, plug
o Yes, call Speedheat®
o
your RugBuddy™
RugBuddy™
#________________
.
.
then, press “Reset” again.
now?
at 1-888-WARM FLOOR (888-
.
-6356) ext. 201.
Repeat
2. Testing the
Wait 2-3 minutes after p
o
o No
Turn on
Turn off
Is there a
o Y
o No,
6356) ext. 201
Troubleshooting Steps using
(IMPORTANT!)
Red Light illuminated.
RugBuddy™ heater panel?
RugBuddy™
and l
and lay on floor again for 5 more minutes
and call Speedheat®
at 1-888-WARM FLOOR (888-927-
.
directed.
.
?
Speedheat® is Floor Heating
Page 1 of 5
USC.470.11.120
PADDING
UG
OR
placed over a hard surface, such as ceramic tile or wood, a non
used for thermal insulation that exceeds 1/8 inch.
If area rug is placed over a soft surface, such as wall
nd may be less than 1/8 inch.
The cushion or padding should be trimmed to be 1 inch smaller than area rug on all four
Place the cushion or pad in the desired position on top of the existing floor covering.
eramic
be used to ensure acceptable heating performance
you may use any non
There is no top or bottom and cord comes out of the corner.
Cord is 6 feet long and connects to GFCI plug.
∙ USC.065.11.120
OR
wall carpeting, a non
a thermal
Speedheat® offers these for
slip thermal insulation padding for area rugs
RugBuddy
Portable Heater for under your Area Rug!
Models: USC.1410.11.120 ∙ USC.940.11.120 ∙
™
∙ USC.370.11.120 ∙ USC.165w.11.120 ∙ USC.165L.11.120
Operating Instructions
and Safety Advice
NON-SLIP AND INSULATION
* IMPORTANT! *
YOU MUST USE A R
YOU MUST USE A RUG
1. For best results:
• If area rug is
•
padding should be used a
o
sides.
2.
3. If the floor covering is c
your convenience, or
prefer.
SPECIFICATION AND INSTALLATION
PAD UNDER YOUR RUGBUDDY™!
CARPET ON TOP OF YOUR RUGBUDDY™!
-to-
tile and installed over a concrete slab,
of the RugBuddy™.
-
-slip pad should be
-creep cushion or
insulation pad must
that you
Note:
Speedheat® is Floor Heating
Page 2 of 5
Loading...