Spectrum Flip-up Shelf for Link Lectern Assembly & Instruction Manual

Assembly Instructions

Assembly Instructions

Important

Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.

Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces­sories, or if you have any questions, please contact us.

www.spectrumfurniture.com

800-235-1262, 715-723-6750

Thank you for purchasing Spectrum products!

(1) 0120069
Flip-up shelf assembly

26”D

[66 cm]

15.25”W

[38.7 cm]

7”D

[17.8 cm]

(1) 039622
2” Grommet

For laminate side panelsFor metal side panels

(4) 0100167
8-32 x 1/2” PH
Thread-cutting screw

(4) 051696
8-32 x 1” PHMS

(4) 0285
3/16 Flat Steel
Washer

(4) 021588
8-32 Keps Nut

1. Before You Begin

Determine:

• Side of the lectern the shelf will be installed. (Left or right-side)

• Upper or lower shelf position

• Type of side panels your lectern has (metal or laminate) Figure 1A

Upper shelf
position
holes

Flip-up Shelf

for Link Lectern

55385

Tools

Lower shelf position holes

Laminate Side Panel

(interior view)

™

Required

Phillips
screwdriver

Upper shelf
position
holes

Proceed to Step 2

Figure 1A

Figure 1B

LaminateMetal

Attaching to Laminate Side Panels:

1. Open the lectern door and remove the rack cube (if equipped).

2. From inside the lectern, use a drill with a 3/16”
drill bit and slowly drill out the corresponding
pre-drilled pilot holes located on the laminate
side panel. Figure 1B. Masking tape can be
used on the exterior to minimize chip-out.

Note: There are (2) holes needed for the upper
position, and (4) needed for the lower position.

0120368R2 Page 1 of 2

Drill with
3/16” drill bit

2. Attach Shelf Brackets to Lectern

1. Remove the instructor-side door and audience-side panel.

2. Extend and lock each folding shelf bracket into the horizontal
position. Figure 2A.

3. Align and attach each bracket to the side of the lectern using:

Folding shelf
bracket

2” Grommet

Metal side panels

Figure 2A

(4) 8-32 x 1/2” PH Thread­cutting screws

4. Tighten all screws securely.

5. Install 2” grommet in shelf.

Shelf bracket

8-32 x 1” PHMS

Laminate side panels

Figure 2B (a 2nd person

to assist may be required)

(4) 8-32 x 1” PHMS
(4) 3/16” Flat steel washers
(4) 8-32 Keps nuts

3/16” drilled hole
from Figure 1B

3/16” Flat steel
washer

Laminate side panel

8-32 Keps nut
(use 11/32” wrench)

Figure 2B

Flip-up shelf
assembly

8-32 screws
(2 required per
bracket)

Metal side
panel

Figure 2A

3. Operation

The shelf will automatically lock into place when lifted into the horizontal
position with the levers released. Figure 3. To lower or ip-up the shelf,
press and hold the levers under each folding shelf bracket at the same
time while slowly lowering or raising the shelf. Do not exceed a maximum
of 35 lb of weight on the shelf. Do not move the lectern while the shelf is
in the horizontal position.

Note: Power and communication wiring for document cameras, laptop

computers, and / or projectors placed on the ip-up shelf should be routed

on top of the audience-side of the shelf. Use of the shelf grommet hole for
wiring will result in pinching of the cords when the shelf is folded.

Release lever

(press here)

CAUTION

Keep clear of pinch points during shelf movement.
Do not exceed 35 lbs [15.9 kg] of weight on shelf.

925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM

© 2016 Spectrum Industries Inc., All rights reserved.

0120368R2 Page 2 of 2

Figure 3