28
12360 S Industrial Dr. East
Plainfield, IL 60585
(800) 248-8873 or (815) 436-4440
FAX: (815) 436-4460
E-Mail: info@specmeters.com
www.specmeters.com
Technologies, Inc.
Spectrum
Catalog # 6110FS
User’s manual
SC 900 Soil
Compaction Meter
Technologies, Inc.
Spectrum
2
CONTENTS
CONTENTSCONTENTS
CONTENTS
General Overview 3
Taking Compaction Measurements 4
Depth Sensor 5
Meter Operation 6
Connecting to a Computer 8
Identifying the COM Port 9
Connecting to a GPS Unit 10
Calibration/Battery Change 11
Main Toolbar 12
Meter Settings 14
Measurement Procedure 16
Warning Messages 18
Data Management 20
Meter Dimensions 21
Specifications 22
Appendix 1: Time Zone Corrections 23
Appendix 2: When to Replace the Cone 24
Warranty 26
This manual will familiarize you with the features and
operation of your new Field ScoutTM SC 900 Soil Compaction
Meter. Please read this manual thoroughly before using your
instrument. For customer support, or to place an order, call
Spectrum Technologies, Inc.
(800)248-8873 or (815) 436-4440
between 7:30 am and 5:30 p.m. CST,
FAX (815)436-4460,
E-Mail: info@specmeters.com.
www.specmeters.com
27
26
Warranty
WarrantyWarranty
Warranty
The Field ScoutTM SC 900 Soil Compaction Meter is
warranted to be free from defects in materials and
workmanship for a period of 1 year from the date of
original purchase. During the warranty period, Spectrum
will, at its option, either repair or replace products that
prove to be defective. This warranty is void if the product
has been damaged by customer error or negligence, or if
there has been an unauthorized modification.
Returning Products to Spectrum
Before returning a failed unit, you must obtain a Returned
Goods Authorization (RGA) number from Spectrum. You
must ship the product(s), properly packaged against
further damage, back to Spectrum (at your expense) with
the RGA number marked clearly on the outside of the
package. Spectrum is not responsible for any package that
is returned without a valid RGA number or for the loss of
the package by any shipping company.
3
Thank you for purchasing the Field ScoutTM SC 900 Soil
Compaction Meter. This manual describes the features
and operation of the meter.
Soil compaction prevents moisture penetration, reduces
fertilizer and chemical uptake and hinders plant root
growth. In some cases, yield losses can run as high as
30% due to compaction. This new electronic soil compaction meter is the most versatile compaction meter on the
market. Soil depth readings are determined by a sonic
depth sensor. Cone index values are measured by a load
cell sensor and can be displayed in PSI or kPa.
The Field Scout’s shaft-mounted probe allows the user to
easily and rapidly take many measurements. The shaft
can be dissembled into 2 pieces for easy storage and transport. The meter’s built-in datalogger can record data from
several sites and eliminates the need to record data manually. Through the software, the user can download the
data, change the logger settings and configure the meter.
General overview
General overviewGeneral overview
General overview
4
Taking Compaction
Taking Compaction Taking Compaction
Taking Compaction
Measurements
MeasurementsMeasurements
Measurements
The SC 900 is a state-of-the-art electronic cone penetrometer for use in soil density, trafficability and compaction studies. This soil compaction instrument measures cone index data, logs the data and allows the user
to review the data to make soil management decisions.
It is recommended that compaction measurements be
taken after a rain, or in the spring when the soils have
good moisture content. Measuring soil compaction in
dry soil conditions will not yield meaningful results.
The SC 900 compaction meter should be used before
tillage to determine where the compacted areas of a
field/plot are. Once the compacted areas, along with
compaction depths, have been determined, a much
more effective tillage system can be employed.
The unit works as an efficient diagnostic tool as well as
a management unit after the tillage operation has been
performed. One can determine how deep the soil has
actually been worked and if the tillage operation has
solved the compaction problems.
25
When you are doing comparative analysis of the
readings in a field or a plot, the measurements will be
consecutive. The amount of wear of the cone will not
be a factor. In this case, it is recommended that the
cone be replaced when the shoulder is not easily recognizable as a shoulder anymore.
New:
0.505"
Figure 3
Replace the cone as follows:
1. Lay meter on its side
2. Unscrew worn cone by hand or with a
pair of pliers
3. Attach new cone into meter shaft
4. Tighten to a snug fit with hands or pliers. Be
careful not to imprint the cone with pliers.
Replacement cones can be ordered from Spectrum
Technologies or an authorized Spectrum Dealer.
24
Appendix 1
Determining When to
Replace Cone
Repeated soil sampling will wear down the metal cone.
Periodically measure the diameter of the cone using a
dial caliper or micrometer that allows you 0.001-inch
measurements.
Place the caliper/micrometer on the shoulder of the
cone. Figure 1 shows the proper placement and Figure
2 the layout of the shoulder.
Figure 1
Shoulder
Figure 2
The determination as to when to replace the cone will
depend on how the user is applying the meter.
If you are using the meter to get absolute compaction
readings, replace the cone when there is a “wear factor”
of 3%. Three percent wear affects the cone index
measurements by 5%. A new cone has a diameter of
0.505“, see Figure 3. When the cone diameter reaches
0.490“ (3% wear), replace the cone.
5
An ultrasonic sensor located at the base of the
meter is used to measure
the depth of penetration.
The field of view extends about 30o from the
shaft. The sensor measures distance by emitting a sound wave and
measuring the travel
time of the first reflected
wave. Usually, this first
reflection will come
from the ground just adjacent to the shaft.
However, if an object
with a surface oriented
toward the sensor is
within the field of view,
an erroneous depth
measurement may be
made. This can lead to
depth error messages (see Warning Messages p. 18). If
possible, try to remove the object and/or smooth the surface. Repositioning your feet and knees may also eliminate these errors. If the problem persists, use a flat target
surface with a hole slightly large than the diameter of the
cone to test the depth sensor and, if necessary, to take
measurements. This target should be about 1 foot wide
and can be made out of cardboard or something sturdier if
more durability is required. To test the sensor, lay the target on the ground and place the shaft in the hole. Have
another person slowly raise the target while you verify the
meter is incrementing the depth.
Depth
Sensor
Depth Sensor
6
Meter operation
Meter operationMeter operation
Meter operation
The ON switch turns the meter/
datalogger on and off. When the meter
is turned on, it will display the battery
status for 3 seconds. For the next 3 sec-
onds, it will display how much logger
memory has been used and, if the logger was enabled in
the software, whether the GPS signal was found. If a GPS
signal is found, latitude and longitude data will be included in the data file.
ON
The meter will then be ready to take readings (see Meas-
urement Procedure pg. 16).
Note: If you are using GPS, but the meter doesn’t find the
GPS signal when powering up, the meter will not search
for the GPS signal when taking readings. Turn the meter
off and on so it can look for the GPS signal. Once the signal is found, GPS information will be included in the data
file until the signal is lost or the GPS unit is disconnected
from the meter.
Logger 75% Full
GPS=Yes DGPS=No
Logger 75% Full
No GPS Found
Sample meter power-up screens with datalogger
enabled: left screen indicates GPS signal was found.
0010 PSI 00 IN
Logger = OFF
If, when powered up, the screen indicates the data logger
is not activated (see above screen), no data will be stored
by the meter. The data logger can be activated through
the SC 900 software (see Meter Settings, pg. 14).
23
Appendix 1
Time zone corrections
Time Zone
Correction
City
0 Dublin, Lisbon, London
3 Rio de Janeiro, Montevideo
4 Asuncion
5 Atlanta, Indianapolis, New York, Ottawa, Bogota,
Montreal, Toronto
6 Guatemala City, Houston, New Orleans, Chicago,
Mexico City, Winnipeg
7 Phoenix, Denver, Edmonton
8 San Francisco, Los Angeles, Vancouver
9 Anchorage
10 Honolulu
11 Wellington
13 Adelaide, Melbourne, Sydney
14 Vladivostok, Brisbane
15 Seoul, Tokyo
16 Beijing, Hong Kong, Manila, Singapore, Taipei
17 Hanoi, Jakarta, Vientiane
18 Calcutta, New Delhi
19 Kabul, Islamabad
20 Tehran, Abu Dhabi, Dubai
21 Moscow, Nairobi, Kampala, Riyadh
22 Ankara, Athens, Helsinki, Istanbul, Cairo,
Johannesburg, Harare
23 Amsterdam, Barcelona, Berlin, Geneva, Paris,
Prague, Rome, Brussels, Madrid, Stockholm,
Warsaw, Lagos
22
Measurement
Units
Cone Index (PSI or kPa)
Resolution
1” (2.5 cm), 5 PSI (35 kPa)
Accuracy
±0.5” (±1.25 cm), ±15 PSI (±103 kPa)
Range
0 - 18” (0 - 45 cm),
0 - 1000PSI (0 - 7000 kPa)
Maximum
Insertion Speed *
72 in/min (182 cm/min)
Maximum
Applied Load *
210 lbs
Power
4 AAA alkaline batteries
Approximately 12 month life
Logger Capacity
772 profiles without GPS,
579 profiles with GPS/DGPS
Display
16 character, 2 line LCD
Weight
2.75 lbs. (1.25 kg)
Specifications
7
Meter operation (cont.)
Meter operation (cont.)Meter operation (cont.)
Meter operation (cont.)
The START button readies the meter
and datalogger to take a profile measurement. It must be pressed before
every attempted profile measurement.
START
After measuring a profile, pressing
the REVIEW button allows the user
to see the cone index value at each
depth. As the button is pressed, the
display screen will scroll sequentially through the entire profile.
REVIEW
Immediately after the meter has successfully taken a full profile measurement, but before measuring another
profile, the DELETE button will delete
the profile before that has just been sent
to the datalogger. The screen will then display the following message:
DELETE
Reading Deleted
8
Connecting to a
Computer
The data port on the underside of the SC 900 meter
(shown above) can be accessed by removing the plastic
screw. It is through this port that the meter is connected to
either a PC or to a GPS unit.
Connecting to a PC
The SC900 software comes with a gray PC interface cable. This cable connects to the 9-pin serial port of your
computer and to the meter’s computer port. The meter’s
configuration can be modified by clicking on the Meter
Settings button (see Meter Settings, p. 14). The Com
Port, Meter Type, Download, Clear Memory and Meter Settings buttons are explained in the Main Toolbar
section (p. 12).
SC 900
data port
21
Meter dimensions
The following are the dimensions of the SC 900 Soil
Compaction Meter.
Meter
7.25”
19.75”
8.5”
12”
Shaft
Connection
Cone Tip
20
The data is stored in comma-delimited text files. These
files can be opened with text-editing software (e.g. Microsoft Word) or spreadsheet software (e.g. Excel).
The first two lines of the data file give the logger’s name
and serial number. The third line indicates that latitude
and longitude are referenced to the 1984 World Geodetic
Survey datum. The fourth line shows the cone index unit
system. The fifth line shows the column headings for the
rest of the data file. Each row of data represents a measurement profile.
Logging sessions are started and completed by turning the
meter on and off. The start of a logging session is indicated by the data line “Logger Started”. If a GPS signal
was found at the start of a logger session a time stamp is
included on the “Logger Started” line.
Sample data showing results of data collected with and
without GPS activated. Note: GPS signal not found when
recording first four sample numbers.
Data Management
Data Management Data Management
Data Management
9
T h e c o m p u t e r
Communications Port to
which the PC-3.5 serial
cable is connected can be
identified by using a
paper clip.
1. Disconnect the serial
cable from the meter.
2. To bring up the Port Selection screen, click on the
Com Port Button, select the com port to be tested and
click the Port Test button. Click the Test Port Now
button. If the message “Connection OK” is displayed,
another device (such as a modem) is probably connected
to that port. If the message “No Connection” is displayed,
this port may be the one connected to your serial cable and
you can proceed to the next step.
3. Place a paperclip on the end of the serial pin so that it
touches both the tip of the pin and the metal area between
the two black rings. Again click on the Test Port Now
button. If the message “Connection OK” now appears,
this is the com port connected to your serial cable.
paper clip
or wire
Identifying the
Identifying the Identifying the
Identifying the
Correct Com Port
Correct Com PortCorrect Com Port
Correct Com Port
NOTE: The meter does not short-circuit the serial pin.
Therefore, when the Test Port Now button is clicked
while the meter is connected, the “No Connection”
message will be displayed.
10
Connecting the SC900 meter to a GPS unit
Cable Connections
A GPS/DGPS cable (item # 2950C) is required to connect
the SC900 meter to a GPS unit. This cable has a 9-pin
male connection and a stereo pin that connects to the meter’s data port. You will also need a cable that allows the
GPS unit to connect to a 9-pin male serial port. If this cable doesn’t come standard with your GPS unit, it should
be available from the manufacturer. This cable is generally used to upload information from a computer to the
GPS unit. These components should be connected as
shown in the figure below.
GPS Setting
Your GPS unit must be set for NMEA 0183 input/output
messages. If the meter has trouble receiving the GPS signal, check that it has the following settings:
Data bits: 8 Stop bits: 1
Baud rate: 4800 bps Parity: None
Timing: 1 second GGA data string
Spectrum
GPS/DGPS
Cable
SC900
Meter
GPS
Unit
GPS computer
interface cable
Connecting to a
GPS Unit
19
Warning
Messages (Cont.)
This error message indicates that the meter missed
a depth reading. This can
be caused by a momentary,
but rapid, insertion of the probe into the soil or by an
object such as a foot or a knee suddenly coming into
the field of view of the sonic depth sensor.
Start Over
!! Depth Error !!
The maximum load the load
cell can withstand is 250
lbs (113 kg). Exceeding
this limit can cause permanent damage to the meter. The “Excessive Force”
warning message appears when 210 lbs (95 kg) or
more is applied to the load cell.
Start Over
Excessive Force
Indicates the batteries need
to be changed. The battery
compartment is located be-
neath the face of the meter.
Low Battery
18
Warning
Messages
If the meter is unable to successfully measure a soil
compaction profile, it will display one of the following
warning messages and no data will be sent to the datalogger. In these instances, it is necessary to withdraw
the probe from the soil (if necessary) and hit the
START button to continue using the meter (see Meas-
urement Procedure pg 16).
Warning Messages
The meter cannot begin taking readings until the probe
senses the tip is at the soil
surface. The meter can
sense a false non-zero depth if the user’s feet are too
close to the shaft, if an object such as a tree or large
plant is near the measurement area or if debris such as
roots, soil or leaf matter is clinging to the shaft.
Start Over
Depth > zero!
If the meter is inserted
faster than the speed al-
lowed by the ASAE stan-
dard (2 inches per 2 seconds), the meter cannot compute the cone index. You
may see this message more often when taking readings
in areas with non-compacted zones beneath strongly
compacted zones.
Start Over
Insertion too fast
11
Calibration/
Calibration/Calibration/
Calibration/
Battery Change
Battery ChangeBattery Change
Battery Change
Calibration
The reading of the meter’s load cell can be recalibrated
with the following procedure.
Note: During the calibration procedure, care must be
taken to ensure that the only force on the load cell is
the weight of the meter itself.
1. Balance the meter in an upright position on a hard surface.
2. Press and hold the START button.
3. With the START button depressed, press and release
the ON button. The LCD will count down from 5 to 1.
4. The meter should now read between 5 and 10 P.S.I.
(35 - 70 Kpa). This reflects the weight of the meter
itself.
Changing the Batteries
To change the batteries, remove the 4 philips-head screws
from the face plate of the meter. Remove the face plate to
access the battery compartment. The meter requires 4
AAA batteries.
12
Com Port
The gray software cable connects the meter to the computer
data port. Select the Com Port
that is assigned to the computer
data port. See Identifying the
Correct Com Port (p. 9) for
instructions on how to determine
which port to select.
Meter Type
Select the SC900 option from the
list of available Field Scout meters.
Main Toolbar
Main ToolbarMain Toolbar
Main Toolbar
17
Measurement
Procedure (Cont.)
depth measurement on the display will increase in
1-inch increments. The cone index will change in
response to soil compaction differences.
4. Push probe into ground slowly and evenly so that
there is not any side stress on the shaft. If an error
message is generated (see Warning Messages pg.
18), start over by removing probe and pushing the
Start button.
5. Remove probe gently. If the profile was successfully measured, the following message will be displayed.
6. You can review compaction measurements
increments by pushing the Review button . You
can also delete the profile by pushing the Delete
button. See Meter Operation (pg. 6) for details.
7. Press Start to ready the probe for the next
measurement.
Geo-Referencing Compaction Measurements:
To geo-reference, you will need to connect a GPS/
DGPS unit to the SC 900 and proceed as described
above. The GPS format should be NMEA 0183. See
Connecting to a GPS Unit (pg. 10) for further details.
Reading Complete
- -Review Mode- -
16
Measurement
Procedure
Recording the best quality data requires some practice.
Your objective is to uniformly push the probe into the
ground using an even motion. The programmed
rate,specified in the ASAE standards, is approximately
2 seconds per 2 inches. If this rate is exceeded, the
meter will show an Error display (see Warning Mes-
sages pg. 18).
To take a profile measurement:
1. Push and release Start button.
2. Wait for LCD to display the profile information
screen. The top line shows the current cone index
and the depth. At the surface the depth will be
zero. The second line indicates how many profiles
have been taken. This resets to 1 every time the
meter is turned on.
3. Stand with your feet at least 4 to 6 inches from the
probe tip. This ensures the sonic depth sensor will
measure accurately. Tall, nearby objects or walls
will also inhibit the ability of the depth sensor to
“see” the ground surface. If you are working in turf
or an especially uneven soil surface, you may need
to use a target to ensure reliable performance (see
Depth Sensor p. 5). It is advisable to smooth the
soil surface as much as possible before inserting the
probe. As the probe is inserted into the soil, the
0010 PSI 00 IN
N=1
Profile Information Screen
13
Download
To download data from the internal data logger, turn
the meter off and connect the gray serial cable to the
RS-232 port on the underside of the meter. Click the
Download button on the main software screen. In the
Save Data As screen, give the file a descriptive name
and select the location where it will be saved.
When the file has been saved, the software will give
you the option of immediately viewing the file. The
data file is stored as a comma-delimited text file and
may be viewed in text editor or spreadsheet software.
Clear Memory
Data is not automatically removed from the logger
memory after a download. The Clear Memory button
clears all data from the logger memory.
Meter Settings
Click this button to configure the meter and data logger. Refer to Meter Settings (p. 14) for more details.
Main Toolbar (Cont.)
Main Toolbar (Cont.)Main Toolbar (Cont.)
Main Toolbar (Cont.)
14
Meter Settings
The Meter Settings screen in the Field Scout Soil Compaction Meter software is used to configure the meter
and datalogger for your specific application. This
screen can be accessed by clicking on the Meter Set-
tings button on the main toolbar screen (see pg. 14).
The fields are described below.
Meter Name: The name given the meter will be the
title on the first line of the downloaded text file.
Logger Settings: The datalogger is enabled and disabled by checking the first box. If the datalogger is
enabled, it will search for a GPS signal when the meter
is turned on. If a signal is found, position data will be
stored along with the soil compaction data. If no GPS
signal is available when the logger is turned on, the
logger will no longer look for one when measuring and
recording soil moisture data. If the second box is
15
checked, the logger will store the GPS value only if it
has been differentially corrected. If the differential
correction is not found, only the soil compaction value
will be stored in the data file. A time-zone correction
should be entered in the third box. Appendix 1 (pg.
23) lists time zone corrections for several cities.
Measurement Units: The meter can be configured to
display and record data in English units (Cone Index in
PSI and depth in inches) or SI units (Cone Index in kPa
and depth in centimeters).
Meter Settings (cont.)
Loading...