66863001
Rev 02
ZigBee
Parts List
ENGLISH
Installation and User Guide
Required tools
Ruler
Additional Tools (depending on application)
Hammer Wood block Chisel
Begin with your smart home app
1
If you will be using a smar t home app with your lock, download the app an d set up
your controller or hub before procee ding further with lock installation.
Phillips head screwdriver
Kwi kse t
1-866-863-6584
www.kwikset.com
Latch
A
B
“B” is n ot included.
If needed, please contact
Kwikset to ord er a drive-in
latch for your l ock.
Strike
C
Adapter
Ring
Keys
E
D
Exterior Assembly
Batteries
Mounting
Plate
G
F
SmartKey
Too l
W
Interior Assembly
L
K
Fasteners
03809 46780
N
P
48654 64109
T
H
S
49191
U
M
Q
V
Prepare the door and check dimensions
2
Make sure your door is compatible. If you have a standard deadbolt mounted
A
separately from the handle below it, your door is compatible.
Compatible Not Compatible
Rim
Lock
Measure to conirm that the hole in the door is either
C D E F
21/8" (54 mm) or 11/2" (38 mm).
21/8"
54 mm
or
11/2"
38 mm
Note: Add itional door
prepara tion may be
require d for doors with
11/2" ( 38 mm) holes .
Consul t the deadbolt
drilling instructions at
kwikset.com/doorprep
Not CompatibleNot Compatible
Mortise
Lock
Measure to conirm that the backset is
either 23/8 " or 23/4" (60 or 70 mm).
backset
23/8" or 23/4"
60 or 70 mm
Integrated
Interior
Measure to conirm that the hole
in the door edge is 1" ( 25 mm).
If drilling a new door, use the supplied template and the complete
door drilling instructions available at kwikset.com/doorpre p
1"
25 mm
Remove your existing deadbolt
B
from your door.
Measure to conirm that the door is between
13/8" and 2 " (35 mm and 51 mm) thick.
13/8" –2"
35 – 51 mm
actual
Install the latch and strike
3
Is the door edge chiseled?
A B
YES
chiseled
Use latch “A”. If the
latch bolt is not already
extended, extend the
latch bolt as shown.
A
or
NO
not
chiseled
Use latch “B” (not
included). If the latch
bolt is not already
extended, extend the
latch bolt as shown.
B
size
NP SQ
face lush against the door edge.
A
Is the D-shaped hole centered in the door hole?
C
YES
or
D-shaped hole D-shaped hole
B
NO
D
Which latch are you installing?Hold the latch in front of the door hole, with the latch
Latch “A” Latch “B”
or
UP is
on top.
A
N (2x)
B
UP is
on top.
wood
block
No adjustment is required.
Proceed to next step.
1 / 4
Rotate latch face as
shown to extend latch.
A
B
Install the strike on the door frame.
E
Make sure the hole in the door frame is drilled a
minimum of 1" (25 mm) deep.
Longer screws
install closest to
the door jamb.
S (2x)
Q (2x)
C
door frame
Install the exterior keypad
4
actual
size
T
What is the diameter of the hole in the door?
A
Diameter is 21/8"
Diameter is 11/2"
(54 mm)
or
21/8"
54 mm
“D” is required for installation.
Install “D” on “F”.
F
D
Locate the screws for step 4C and keep them within reach.
B
T
38 mm
“D” is not needed for
installation. Discard “D”.
(38 mm)
11/2"
Install the exterior keypad and mounting plate.
C
a
b
Support the exterior
assembly during mounting
plate installation .
G
F
The cable goes
underneath the latch.
D
c
Keep parallel to the
edge of the door.
d
T
Tighten
screws evenly.
T (2x)
Route the cable
through the center
hole, then push it into
the bottom hole.
E
Insert the key and
test the latch . If the
latch does not extend
or retract smoothly,
adjust the screws (T).
Remove the key when
inished, and make
sure the latch bolt
is fully extended.
Install the interior assembly
5
Remove the interior cover and battery pack from the interior assembly. Install the interior assembly onto the mounting plate.
A B
a
b
L
Make sure the turnpiece is
in the vertical position.
c
L
d
Make sure
turnpiece shaft is
rotated as shown.
M
K
Do not install
batteries
until step 6.
L
a
L
Ensure tight cable
connection.
c
actual
size
U
b
align
Lay the excess cable
lat inside the bottom of
the interior housing.
d
U
(2x)
bottom
hole
Install the batteries and perform the door handing process
6
This step will teach your lock the orientation of your door and is crucial to lock operation.
Install 4 AA batteries in the battery pack. With the door open, press and HOLD the
A B C
W
Lock button while installing the battery pack.
Hold the button until the latch bolt
starts moving on its own.
K
K
Ensure correct polarity.
For best results, use
new, non-rechargeable
Alkaline batteries only.
The latch will retract and extend to learn the orientation of the door.
If the bolt does not move,
make sure the batteries
are correctly installed, and
perform step 6B again.
Note: The latch
bolt will only
retract half way.
The Status LED will indicate success or failure.
D
Green: Door handing was
successful. Proceed to next step.
Red: Door handing was
unsuccessful. Make sure the lock
interior and batterie s are correctly
installed. Perform step 6B again.
2 / 4
Pair the lock with your smart home system
7
Initiate the pairing process through
A B C
your smart home system (either
through your smart home app, at your
panel, or at your controller or hub).
Refer to your smart home system
instructions for more information.
Add user codes (30 maximum)
8
It is recommended that you add and delete all user codes through your smart home system.
If your system does not allow this, codes may be added directly to the lock as shown here.
Programming information
A
Mastercode: For enhanced security, a
mastercode may be used when adding
and deleting user codes. For more
information about the mastercode,
download the SmartCode 914
Programming and Troubleshooting
Guide at ww w.kwikset.com.
Programming Timeout: During
programming, if no button is pressed
for ive seconds, the system will time
out (indicated by three beeps and a red
lashing keypad), and you will need to
restart the procedure.
Make sure the door is open.
B
Press the Program button once.
When prompted by your smart home
system to initiate pairing at the lock, press
button “A” on the lock interior four times.
button “A” button “B”
Enter a new user code. A total of 30
C
user codes may be programmed.
If the pairing process is successful, re-name
the lock in your system (if applicable).
If the pairing process is unsuccessful,
D
press button “B” nine times.
Perform steps 7A7C again.
If still unsuccessful, follow your smart home system's
instructions to remove (exclude/unpair) the lock from
any other network. Then perform steps 7A7C again.
Press the Lock button once.
D
Each user code
must be a unique
code between
4 and 8 digits,
depending on
your smart home
system.
What lights and sounds does the lock produce?
E
One green lash with one beep Three red lashes with three beeps
green
1x
Programming was successful. Programming was unsuccessful .
Test the lock and check door alignment
9
With the door open, press the Lock
A B C D
button. Conirm that the door locks.
Enter the user code(s) added
in the previous step. Conirm
that the door unlocks.
or
Move swiftly through
programming, as the
system will time out if
no button is pressed
red
Make sure the user code is
not a duplicate and that it
is between 4 and 8 digits
during your next attempt.
for ive seconds.
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon.
Close the door. Press the Lock
button. Conirm that the door
locks smoothly without error.
3x
Make sure the l ock has
room for an additional code.
If all use r code positions
are ille d, delete a code to
make room for this one.
If your does not lock smoothly,
make sure you replaced your
previous latch and strike with
those supplied in the box.
If you still experience locking
errors, call Kwikset Support to
order a Warped Door Service Kit.
Kwikset Support: 18668636584
10
Re-key the lock (if needed) and install the battery cover
Optional: Re-key the lock.
A B
a
IMPORTANT:
Remove battery
pack before
re-keying.
K
b
Re-key the lock
to work with your
existing key. See
the supplied
SmartKey Re-key
instructions for
more information.
c
Reinstall
battery
pack.
K
H
3 / 4
Install the battery cover.
a
M
actual
size
V
b
V (3x)
Reference Guide
SmartCode at a Glance
Exterior
Keypad
SmartKey
tool hole
Lock
button
Keyway
Interior (cover removed)
Back
panel
Button “A” Button “B”
Program
button
Switches
Status
LED
Tur np ie ce
shaft
Note: When the cover is removed,
the turnpiece shaft can be used to
manually lock and unlock the door.
System Alerts
Alert Reason Solution
Keypad lashes red once with
one beep*.
Keypad lashes red three
times with three beeps*.
Keypad lashes red 15 times
with 15 beeps*
Keypad lashes red with fast
beeping sound for three to
four seconds.
Keypad lashes red with
continuous beeping sound
for two seconds.
Lock beeps continuously.
*Beep ing sound will only b e heard if switch #3 is on.
Switches and Status LED colors Troubleshooting
These features can be adjusted in some smart home apps.
One incorrect code entered. Re-enter code.
No user code programmed. Program at least one user code.
Programming timeout after ive
seconds.
Unsuccessful programming.
Three incorrect codes entered
within one minute.
Low battery. Replace batteries.
Door jammed while attempting
to lock.
Interior assembly is
disconnected from exterior.
Attempt programming procedure again.
Re-enter code after 60 second keypad
lockout.
Manually re-lock door. If needed,
reposition strike.
Remove battery pack, reconnect the interior
to the exterior, then reinstall battery pack.
Switches
On
O
Status
LED
1 2 3 4
Switch Function
Door lock status LED blinks every 6
1
seconds
Lock automatically re-locks door 30
2
seconds after unlocking. Disabled if no
codes are programmed.
3 Audio
4 Not used.
Color Lock Status
Blinking green Unlocked
Blinking amber Locked
Blinking red Low battery
Door handing process
Solid red
did not work properly.
See the online
Programing and
Troubleshooting Guide.
Deleting a single user code (manually at the lock)
Note: All codes may be deleted at once if the mastercode is enabled. For more information about the
mastercode, consult the Smar tCode 914 Programming and Troubleshooting Guide at www.kwikset.com.
1 Keep door open.
Press Program
button once.
2 Press Lock
button once.
3 Enter user code
to be deleted.
4 Press Lock
button once.
A complete SmartCode 914 Programming and
Troubleshooting Guide is available at www.kwikset.com.
Factory Reset
A factory re set will delete all codes associated with the lock,
and it will remove it from your smart home system.
1 Remove
battery pack.
2 Press and HOLD the Program
button while reinserting
the battery pack.
Keep holding the button for 30
seconds until the lock beeps
and the status LED lashes red.
Status
LED
5 Re-enter user code. 6 Press Lock
button once.
If no button is pressed for ive seconds, the system will time out, and
you will nee d to restart the procedure.
If unsuccessful
Make sure to enter
the same valid code
in steps 3 and 5.
Tes t co de
While the door is
open, test the user
code to make sure
it no longer unlocks
the door.
3 Press the Program button
once more. When the LED
lashe s green and you
hear one beep, the lo ck
has been reset.
Network Information Important Safeguards
ZigBee System Notes
ZigBee is a “Wireless mesh network,” and results may vary based on building construction and
communication path, with 35+ feet being typical installed distance in a st andard home environment and
250 feet+ when the lock has a clear line of sight with the smart home controller or hub. It may be necessary
to install a dditional ZigBee devices to enhance the communication path between the lock and controller/
hub for a more robust ZigBee network .
Removing the lock from the network
Press button “B” on the lock interior nine times.
1. Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel
can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualiied locksmith or other security professional.
4 Perform th e door handing process again
to teach the lock the orientation of the
door, pair the lock with your smart home
system, and add user codes to your lock.
4 / 4
© 2017 Spectrum Brands, Inc.
Loading...