Spectrum 450191ZWV User Manual

Home Connect

44571 / 04

HomeConnect Lock Configuration Guide

HomeConnect Lock Configuration Guide
HomeConnect Lock Configuration Guide

English

1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.

2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.

3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.

Notes

1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.

2. Deleting access code(s) can only be
done directly from the Z-Wave or ZigBee
control system.

3. Depending on the controller location
and Z-Wave protocol version, it may be
necessary to perform the inclusion process
on the HomeConnect Lock within 12
inches from the control system. During
the inclusion process, ensure that both
the control system and HomeConnect lock
remain stationary for a total of 60 seconds
to complete the encryption exchange and
for the lock to be properly displayed on the
Z-Wave control system.

4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.

5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.

Español

1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.

2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.

3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.

Notes

1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.

2. Deleting access code(s) can only be done
directly from the Z-Wave or ZigBee control
system.

3. Depending on the controller location and
Z-Wave protocol version, it may be necessary
to perform the inclusion process on the
HomeConnect Lock within 12 inches from
the control system. During the inclusion
process, ensure that both the control system
and HomeConnect lock remain stationary
for a total of 60 seconds to complete the
encryption exchange and for the lock to be
properly displayed on the Z-Wave control
system.

4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.

5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.

Français

1. Ensure you have followed all the steps in
the SmartCode Quick Installation Guide.

2. Locate and remove the interior cover from
your HomeConnect lock to expose the
Programming Instructions on the lock. See
Figure 1.

3. For inclusion or exclusion of the lock, refer
to your Z-Wave or ZigBee control system
instructions and reference Figure 2.

Notes

1. This HomeConnect lock supports 30 user
access codes. It is recommended to add
or change access code(s) directly from the
Z-Wave or ZigBee Control system.

2. Deleting access code(s) can only be done
directly from the Z-Wave or ZigBee control
system.

3. Depending on the controller location and
Z-Wave protocol version, it may be necessary
to perform the inclusion process on the
HomeConnect Lock within 12 inches from
the control system. During the inclusion
process, ensure that both the control system
and HomeConnect lock remain stationary
for a total of 60 seconds to complete the
encryption exchange and for the lock to be
properly displayed on the Z-Wave control
system.

4. Z-Wave is a “Wireless mesh network,” and
although Z-Wave has an estimated open air
range of 65 feet, results may vary based on
building construction and communication
path, with 35 feet+ installed distance being
typical. It may be necessary to install a
repeatable or beaming Z-Wave device (i.e.
lamp module) to enhance the communication
path with the controller for a more robust
Z-Wave network.

5. If first inclusion attempt was unsuccessful,
perform exclusion process (see Figure 2) to reset
the lock. Then, repeat the inclusion process.

For technical assistance,

call 1-866-863-6584

PROGRAM MI NG
INSTRUCTIO N S

READY

A B

Press program button below once to enter
the 1st code & twice for the 2nd code

Enter code on exterior keypad

Press on exterior keypad to set code

Future Feature

Mute Beeper

Auto-Lock

LED Notification

PROGRAM

BUTTON

SETTINGS

Fig. 1 Fig. 2

For technical assistance,

call 1-866-863-6584

Inclusion/Exclusion Configuration Process for HomeConnect Locks

HomeConnect Lock Type

HomeConnect Lock Type
HomeConnect Lock Type

For technical assistance,

call 1-866-863-6584

Inclusion/Exclusion Conguration Process for HomeConnect Locks
Inclusion/Exclusion Conguration Process for HomeConnect Locks

Inclusion

Inclusión
Inclusion

Exclusion

Exclusión
Exclusion

A (x1) A (x1)

Z-Wave

A (x4) B (x9)

Zigbee

Copyright © 2013 Spectrum Brands, Inc.

Home Connect

44571 / 04

HomeConnect Lock Configuration Guide

HomeConnect Lock Configuration Guide
HomeConnect Lock Configuration Guide

English

REGULATORY COMPLIANCE

This product complies with standards established by the
following regulatory bodies:

•Federal Communications Commission (FCC)

•Industry Canada

FCC

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (
1 ) this device may not cause harmful interference, and
( 2 ) this device must accept any interference received,
including interference that may cause undesired operation.

This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communi-cations. However,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

receiver.

•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV
technician for help.

IMPORTANT! Changes or modifications not expressly
approved by the manufacturer could void the user’s
authority to operate the equipment.

INDUSTRY CANADA

This Class B digital apparatus complies with Canada
ICES-003. CAN/CSA-C22.2 NO. 14-05 (Industrial Control
Equipment) Operation is subject to the following two
conditions: ( 1 ) this device may not cause interference,
and ( 2 ) this device must accept any interference,
including interference that may cause undesired operation
of the device.

Z-WAVE

•Security enabled Z-Wave product

•Security enabled Z-Wave controller must be used in

order to fully utilize product.

This Z-Wave-enabled door lock can be included, operated,
and is fully interoperable with any Z-Wave secure
controller.

Español

CUMPLIMIENTO NORMATIVO

Este producto cumple con las normas establecidas por los
siguientes organismos reguladores:

•Comisión Federal de Comunicaciones (FCC)

•Industry Canada

FCC

Este dispositivo cumple con la 15ª parte del reglamento
de la FCC. Su funcionamiento está sujeto a las siguientes
dos condiciones: ( 1 ) este dispositivo no deberá causar
ninguna interferencia dañina, y ( 2 ) este dispositivo deberá
aceptar cualquier interferencia recibida, incluyendo aquélla
que podría causar un funcionamiento no deseado.

Se realizaron pruebas a este equipo cuyos resultados
revelaron que cumple con los límites establecidos para
un dispositivo digital de la Clase B, conforme a la 15ª
parte del reglamento de la FCC. Estos límites han sido
impuestos para proporcionar protección razonable contra
interferencias dañinas en una instalación residencial.
Este equipo genera, utiliza y puede irradiar energía de
radiofrecuencia y, si no se instala y utiliza según lo que
indican las instrucciones, podría causar interferencia
dañina en radiocomunicaciones. Sin embargo, no
hay garantía de que la interferencia no ocurrirá en
determinadas instalaciones. Si este equipo efectivamente
causa interferencia en la recepción de radio o televisión,
la cual puede determinarse encendiendo y apagando
el equipo, sugerimos al usuario que intente corregir
dicha interferencia tomando una o más de las siguientes
medidas:

•Volver a orientar o ubicar la antena receptora.

•Incrementar la distancia entre el equipo y el recibidor.

•Conectar el equipo a una toma de corriente en un

circuito distinto del circuito en el cual esté conectado
el recibidor.

•Consultar con el distribuidor o un técnico de radio y TV
con experiencia para obtener su ayuda.

¡IMPORTANTE! Todo cambio o modificación no
aprobado expresamente por el fabricante podría
desautorizar al usuario para operar el equipo.

INDUSTRY CANADA

Este aparato digital de clase B cumple con la norma
Canada ICES-003. CAN/CSA-C22.2 No. 14-05 (Equipo
de Control Industrial) Su funcionamiento está sujeto a las
siguientes dos condiciones: ( 1 ) este dispositivo no deberá
causar ninguna interferencia dañina, y ( 2 ) este dispositivo
deberá aceptar cualquier interferencia, incluyendo aquélla
que podría causar el funcionamiento no deseado del
dispositivo.

Z-WAVE

•Producto Z-WAVE con seguridad permitida.

•El regulador de la seguridad permitida del producto

Z-WAVE se debe usar para utilizar copletamente el
producto.

Esta cerradura de puerta Z-WAVE-permitida puede ser
incluida, funcionada, y es completamente interoperable con
cualquier Z-WAVE regulador seguro.

Français

REGULATORY COMPLIANCE

This product complies with standards established by the
following regulatory bodies:

•Federal Communications Commission (FCC)

•Industrie Canada

FCC

Cet appareil est conforme aux limites prescrites dans la
partie 15 des règlements de la Federal Communication
Commission (FCC) des États-Unis. Son utilisation est
subordonnée aux conditions suivantes : (1) l’appareil ne
doit pas causer d’interférence, et (2) il doit accepter toute
interférence, y compris celles qui peuvent causer son
mauvais fonctionnement.

Lors des tests effectués, cet appareil s’est révélé conforme
aux limites prescrites dans la partie 15 des règlements
de la Federal Communication Commission (FCC) des
États-Unis pour un appareil numérique de Classe B. Ces
limites ont été fixées pour protéger raisonnablement
les installations résidentielles contre les interférences
nuisibles. L’appareil produit, utilise et peut émettre

des radiofréquences. S’il n’est pas installé et utilisé de la
façon prescrite, il peut brouiller les communications radio.
Il n’est pas garanti qu’aucune interférence ne se produira.
Si l’appareil brouille la réception d’une radio ou d’un
téléviseur (pour savoir s’il est à l’origine du brouillage, il
suffit de l’éteindre et de le rallumer), l’utilisateur est invité à
tenter de corriger la situation en prenant une ou plusieurs
des mesures suivantes :

•réorienter ou déplacer l’antenne réceptrice;

•éloigner davantage l’appareil émetteur du récepteur;

•brancher l’appareil dans une prise reliée à un circuit

différent de celui auquel le récepteur est relié;

•consulter le détaillant ou un technicien de
radiotélévision expérimenté pour obtenir de l’aide.

IMPORTANT! Les modifications qui n’ont pas été
expressément approuvées par le fabricant de l’appareil
peuvent annuler l’autorisation d’utiliser l’appareil.

INDUSTRIE CANADA

Cet appareil numérique de la Classe B est conforme à la
norme NMB-003 du Canada. CAN/CSA-C22.2 No. 14-05
(Appareil Industriel de Contrôle L’opération est sujette
aux deux conditions: ( 1 ) ce dispositif peut ne pas causer
l’interférence et ( 2 ) ce dispositif doit accepter n’importe
quelle interférence, y compris l’interférence qui peut
causer le fonctionnement peu désiré du dispositif.

Z-WAVE

•La sécurité a permis le produit de Z-WAVE.

•Le contrôleur de Z-WAVE permis par sécurité doit être

employé afin d’utiliser entièrement le produit.

Ceci serrure de porte Z-WAVE-permise peut être inclus,
fonctionné, et est entièrement interopérable avec le tout
Z-WAVE contrôleur bloqué.